PCDD/F and dioxin-like PCB minimization: A 13-year experimental study along the flue gas cleaning system of a secondary aluminium refining plant

Accounting of the Use and Emissions of Polychlorinated Biphenyl Compounds (PCBs) in India, 1951-2100

Polychlorinated biphenyl compounds (PCBs) are highly toxic organic chemicals still prevalent in the environment. While global inventories of the use and emissions of PCBs have been developed, estimates for individual countries determined using bottom-up approaches are few and often show different trends from the global inventory. Here, we determine the past, present, and future consumption and emissions of PCBs in India. A mass balance model was used to estimate middle (low-high) emissions in the period 1950-2100. Up to 7296 tonnes of PCBs have been used in transformers. PCBs imported as wastes are estimated to be approximately 5000 (2400-9100) tonnes. Total emissions from the use and disposal of transformers, industrial processes, and imported waste disposal are estimated to become 13 (0.1-537) tonnes, 89.26 (0.5-178) tonnes, 63 (3-910) tonnes, respectively, in the period 1950-2100. Congener-specific emissions are relatively high for low-chlorinated PCBs (-8, 18, 28, 31, 52, 101, 110, 118, 153, range: 0.1-118 tonnes). We find that industrial emissions are becoming important sources of PCBs and may become predominant, depending on emission scenarios.

Investigation on Pollution Control Device (PCD) in iron foundry industry to reduce environmental chemicals

Right from the olden days, many products have been made according to foundry practices in order to generate prosperity in the societies in which they operate while reaping these types of benefits through the operation of foundries. It is alarming that the emissions released by foundries affect human health. Therefore, foundries installed Pollution Control devices (PCDs), in accordance with this development; researchers examined the effectiveness of these PCDs in controlling emissions from foundries in different parts of the world. The emission control obtained by installing these PCDs is explained in this article based on the data gathered from the survey. The cartridge filter equipped with an induction furnace reduced the concentration of SPM to less than 20 mg/Nm³. This result of the investigation indicates that the cartridge filter built into the induction furnace achieves the best efficiency in controlling contaminants from iron foundries. Interestingly, the operation of the cartridge filter has yet to be documented. Therefore, the construction operation, the performance of the cartridge filter, and its efficiency in achieving contaminations control in foundries are described. This will provide useful information on the use of cartridge filters in an induction furnace to reduce Iron foundry emissions.

Recent advances in PCB removal from historically contaminated environmental matrices

Despite being drastically restricted in the 1970s, polychlorinated biphenyls (PCBs) still belong among the most hazardous contaminants. The chemical stability and dielectric properties of PCBs made them suitable for a number of applications, which then lead to their ubiquitous presence in the environment. PCBs are highly bioaccumulative and persistent, and their teratogenic, carcinogenic, and endocrine-disrupting features have been widely reported in the literature. This review discusses recent advances in different techniques and approaches to remediate historically contaminated matrices, which are one of the most problematic in regard to decontamination feasibility and efficiency. The current knowledge published in the literature shows that PCBs are not sufficiently removed from the environment by natural processes, and thus, the suitability of some approaches (e.g., natural attenuation) is limited. Physicochemical processes are still the most effective; however, their extensive use is constrained by their high cost and often their destructiveness toward the matrices. Despite their limited reliability, biological methods and their application in combinations with other techniques could be promising. The literature reviewed in this paper documents that a combination of techniques differing in their principles should be a future research direction. Other aspects discussed in this work include the incompleteness of some studies. More attention should be given to the evaluation of toxicity during these processes, particularly in terms of monitoring different modes of toxic action. In addition, decomposition mechanisms and products need to be sufficiently clarified before combined, tailor-made approaches can be employed.