Reaction kinetics and mechanisms of organosilicon fungicide flusilazole with sulfate and hydroxyl radicals

Implementation of laser flash photolysis for radical-induced reactions and environmental implications

Confronted with the imperative crisis of water quality deterioration, the pursuit of state-of-the-art decontamination technologies for a sustainable future never stops. Fitting into the framework of suitability, advanced oxidation processes have been demonstrated as powerful technologies to produce highly reactive radicals for the degradation of toxic and refractory contaminants. Therefore, investigations on their radical-induced degradation have been the subject of scientistic and engineering interests for decades. To better understand the transient nature of these radical species and rapid degradation processes, laser flash photolysis (LFP) has been considered as a viable and powerful technique due to its high temporal resolution and rapid response. Although a number of studies exploited LFP for one (or one class of) specific reaction(s), reactions of many possible contaminants with radicals are largely unknown. Therefore, there is a pressing need to critically review its implementation for kinetic quantification and mechanism elucidation. Within this context, we introduce the development process and milestones of LFP with emphasis on compositions and operation principles. We then compare the specificity and suitability of different spectral modes for monitoring radicals and their decay kinetics. Radicals with high environmental relevance, namely hydroxyl radical, sulfate radical, and reactive chlorine species, are selected, and we discuss their generation, detection, and implications within the frame of LFP. Finally, we highlight remaining challenges and future perspectives. This review aims to advance our understandings of the implementation of LFP in radical-induced transient processes, and yield new insights for extrapolating this pump-probe technique to make significant strides in environmental implications.

Dual Role of Silicon-based Matrices in Electron Exchange Matrices for Waste Treatment

Para chloro aniline (PCA) is a common toxic pollutant found in pharmaceutical wastewater. Our study suggests a novel PCA treatment method based on a heterogeneous advanced oxidation process (AOP) that proceeds in an electron exchange matrix (EEM) prepared by the incorporation of redox-active specie in silica matrices using the sol-gel synthesis route. The results, which are supported by DFT calculations, show that the silicon skeleton of the EEM has two important roles, both as a porous matrix that hosts the redox species and as an oxidant species involved in the AOP. The calculations indicate that the formation of a radical on the nitrogen is favored. The suggested mechanism could shed light on the AOP, which proceeds in a heterogenous system, and on its application inside the understudied EEMs that, until now, have been a virtual black box. A better understanding of the mechanism could lead to improved control over the heterogeneous processes that can play a critical role in industries with the need to treat small amounts of toxic compounds at low concentrations, such as in the pharmaceutical industry.

Carbon dots decorated magnetite nanocomposite obtained using yerba mate useful for remediation of textile wastewater through a photo-Fenton treatment: Ilex paraguariensis as a platform of environmental interest-part 2

Two carbon dots (CD) with diameters of 4.9 ± 1.5 and 4.1 ± 1.2 nm were successfully synthesized through an acid ablation route with HNO₃ or H₂SO₄, respectively, using Ilex paraguariensis as raw material. The CD were used to produce magnetite-containing nanocomposites through two different routes: hydrothermal and in situ. A thorough characterization of the particles by transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), dynamic light scattering (DLS), Fourier transform infrared (FTIR), and X-ray photoelectron spectroscopy (XPS) indicates that all nanomaterials have spherical-like morphology with a core-shell structure. The composition of this structure depends on the route used: with the hydrothermal route, the shell is composed of the CD, but with the in situ process, the CD act as nucleation centers, and so the iron oxide domains are in the shell. Regarding the photocatalytic mechanism for the degradation of methyl orange, the interaction between the CD and the magnetite plays an important role in the photo-Fenton reaction at pH 6.2, in which ligand-to-metal charge transfer processes (LTMCT) allow Fe²⁺ regeneration. All materials (100 ppm) showed catalytic activity in the elimination of methyl orange (8.5 ppm), achieving discoloration of up to 98% under visible irradiation over 400 nm in 7 h. This opens very interesting possibilities for the use of agro-industrial residues for sustainable synthesis of catalytic nanomaterials, and the role of the interaction of iron-based catalysts with organic matter in heterogeneous Fenton-based processes.

Enhanced degradation of bisphenol S by persulfate activated with sulfide-modified nanoscale zero-valent iron

Sulfide-modified nanoscale zero-valent iron (S-nZVI) has been considered an efficient material to remove heavy metals and organic contaminants. The experiments of bisphenol S (BPS) degradation by persulfate (PS) activated with S-nZVI (S-nZVI/PS) or nZVI (nZVI/PS) were carried out in this paper. The results show that, compared to the bare nZVI/PS system, the S-nZVI/PS system shows higher activity in BPS degradation, especially at high BPS concentration. The reaction rate constant k_obs of BPS removal by the S-nZVI/PS system (0.142 min^-1) was much higher than that in nZVI/PS system (0.089 min^-1) because more oxidation species were generated in the S-nZVI/PS system. The results of electron paramagnetic resonance (EPR) and radical quenching tests show that both hydroxyl radical (·OH) and sulfate radical (SO₄^·-) were involved in the degradation of BPS and had a great contribution to BPS removal. Moreover, the effects of S/Fe molar ratio, S-nZVI dosage, initial pH, and initial concentration of PS or BPS on S-nZVI/PS were also studied. The results show that the S/Fe molar ratio has significant influence on the BPS degradation; over 97.7% of the removal efficiency was achieved at 0.035 of S/Fe molar ratio. And the removal efficiency of BPS degradation increased with the increase of the dosage of S-nZVI, PS concentration. Furthermore, BPS could be efficiently removed in solutions with a wide range of initial pH (3.13-9.35). The observed results show that it is promising in the removal of micro-pollutants from water by persulfate activated with S-nZVI.

Experimental and theoretical insight into hydroxyl and sulfate radicals-mediated degradation of carbamazepine

Carbamazepine (CBZ), a widely detected pharmaceutical in wastewaters, cannot currently be treated by conventional activated sludge technologies, as it is highly resistant to biodegradation. In this study, the degradation kinetics and reaction mechanisms of CBZ by hydroxyl radical (OH) and sulfate radical ()-based advanced oxidation processes (AOPs) were investigated with a combined experimental/theoretical approach. We first measured the UV absorption spectrum of CBZ and compared it to the theoretical spectrum. The agreement of two spectra reveals an extended π-conjugation system on CBZ molecular structure. The second-order rate constants of OH and with CBZ, measured by competition kinetics method, were (4.63 ± 0.01) × 10⁹ M^-1 s^-1 and (8.27 ± 0.01) × 10⁸ M^-1 s^-1, respectively at pH 3. The energetics of the initial steps of CBZ reaction with OH and were also calculated by density functional theory (DFT) at SMD/M05-2X/6-311++G**//M05-2X/6-31 + G**level. Our results reveal that radical addition is the dominant pathway for both OH and . Further, compared to the positive ΔG_R⁰ value for the single electron transfer (SET) reaction pathway between CBZ and OH, the ΔG_R⁰ value for SET reaction between CBZ and is negative, showing that this reaction route is thermodynamically favorable. Our results demonstrated the remarkable advantages of AOPs for the removal of refractory organic contaminants during wastewater treatment processes. The elucidation of the pathways for the reaction of OH and with CBZ are beneficial to predict byproducts formation and assess associated ecotoxicity, providing an evaluation mean for the feasibility of AOPs application.

Evaluation of transformation products from chemical oxidation of micropollutants in wastewater by photoassisted generation of sulfate radicals

In this research, the degradation of seven different micropollutants (MPs) and the formation of their transformation products (TPs) have been assessed during the application of different advanced oxidation processes: photolytic and photocatalytic activation of peroxymonosulfate (PMS) and persulfate (PS). The results were compared with those obtained from the photolytic experiments using hydrogen peroxide (H₂O₂) as oxidant. A significant abatement of almost all MPs was achieved, even with very low UV-C contact time (9 and 28 s). The degradation of atenolol (ATN) and caffeine (CFN) ranged from 84 to 100% with a dose of 0.5 mM of any oxidant. The efficiencies for bisphenol-A (BPA), carbamazepine (CBZ), diclofenac (DCF), ibuprofen (IBP), and sulfamethoxazole (SMX) varied depending on the oxidation system and operating conditions (oxidant dose and UV-C contact time), leading to the photolysis of PMS to higher efficiencies than PS and H₂O₂. In all cases, the abatement of MPs ranged from 63 to 83%, even with the lowest PMS dosage. Moreover, the addition of Fe(II) as a catalyst enhanced the removal efficiency, reaching almost total removal, especially over CBZ, DCF, and IBP. The Dissolved Organic Carbon (DOC) removal ranged between 44 and 62%, suggesting the transformation of MPs in intermediate compounds. The identification of transformation products was carried out for each micropollutant and each oxidation treatment, being observed some transformation products specific of oxidation by sulfate radicals. For example, m/z 165.0432 only appeared after PMS/Fe(II)/UV-C on the degradation of BFA, m/z 251.082 appeared after photolytic activation of PMS and PS on CBZ removal, and m/z 128.0452 was observed after any sulfate radical oxidation treatment, but not after photolysis of H₂O₂.

Reclamation of agro-wastewater polluted with pesticide residues using sunlight activated persulfate for agricultural reuse

The removal of 17 pesticides (pymetrozine, flonicamid, imidacloprid, acetamiprid, cymoxanil, thiachloprid, spinosad, chlorantraniliprole, triadimenol, tebuconazole, fluopyram, difenoconazole, cyflufenamid, hexythiazox, spiromesifen, folpet and acrinathrin) found in agro-wastewater from washing of containers and phytosanitary treatments equipment, has been carried out using sodium persulfate (Na₂S₂O₈) at pilot plant scale under natural sunlight. Persulfate is a strong oxidant, inexpensive and environmentally appropriate. However, this oxidant is slow in kinetics under ordinary conditions. Na₂S₂O₈ can be activated by ultraviolet light, generating SO₄^- radicals, which are also a very strong oxidizing species (E₀ = 2.6 V). Previously, preliminary experiments were carried out at laboratory scale using a photoreactor to optimize the Na₂S₂O₈ (300 mg L^-1) concentration on the rate constants of the found pesticides. The residual levels of the studied pesticides in agro-wastewater (900 L) were in the range 0.02-1.17 mg L^-1 for acrinathrin and fluopyram, respectively. After treatment, nearly complete degradation (>97%) of the parent molecules was achieved although 13% of initial DOC was measured. No significant differences (p < 0.05) were found when comparing grown broccoli using reclaimed and unreclaimed water.

Rate constants of sulfate radical anion reactions with organic molecules: A review

The rate constants of sulfate radical anion reaction (k_SO4-) with about 230 organic molecules of environmental interest are tabulated and discussed, together with both the methods of rate constant determinations and the reaction mechanisms. k_SO4-'s were collected from the original publications. The highest values in the ∼10⁹ M^-1 s^-1 range are published for aromatic molecules. There is a tendency that electron donating substituents increase and electron withdrawing substituents decrease these values. There are just a few compounds with rate constants established using different techniques in different laboratories. k_SO4-'s determined in different laboratories by the direct techniques, pulse radiolysis or laser flash photolysis, in most cases agree reasonably. The values determined by competitive experimental techniques, by complex kinetics calculations, or by modelling show a large scatter. Some of these techniques seem to be questionable for k_SO4- determination. The sulfate radical anion reacts with ketone and amine moieties of molecules by electron transfer. The same mechanism is also suggested for the reaction with aromatic rings. However, in a few cases addition to the double bond and sulfate anion elimination reactions were distinguished. A typical reaction with the aliphatic parts of the molecule is H-abstraction.

Micropollutants removal by full-scale UV-C/sulfate radical based Advanced Oxidation Processes

The high chemical stability and the low biodegradability of a vast number of micropollutants (MPs) impede their correct treatment in urban wastewater treatment plants. In most cases, the chemical oxidation is the only way to abate them. Advanced Oxidation Processes (AOPs) have been experimentally proved as efficient in the removal of different micropollutants at lab-scale. However, there is not enough information about their application at full-scale. This manuscript reports the application of three different AOPs based on the addition of homogeneous oxidants [hydrogen peroxide, peroxymonosulfate (PMS) and persulfate anions (PS)], in the UV-C tertiary treatment of Estiviel wastewater treatment plant (Toledo, Spain) previously designed and installed in the facility for disinfection. AOPs based on the photolytic decomposition of oxidants have been demonstrated as more efficient than UV-C radiation alone on the removal of 25 different MPs using low dosages (0.05-0.5 mM) and very low UV-C contact time (4-18 s). Photolysis of PMS and H₂O₂ reached similar average MPs removal in all the range of oxidant dosages, obtaining the highest efficiency with 0.5 mM and 18 s of contact time (48 and 55% respectively). Nevertheless, PMS/UV-C reached slightly higher removal than H₂O₂/UV-C at low dosages. So, these treatments are selective to degrade the target compounds, obtaining different removal efficiencies for each compound regarding the oxidizing agent, dosages and UV-C contact time. In all the cases, H₂O₂/UV-C is more efficient than PMS/UV-C, comparing the ratio cost:efficiency (€/m³·order). Even H₂O₂/UV-C treatments are more efficient than UV-C alone. Thus, the addition of 0.5 mM of H₂O₂ compensates the increased of UV-C contact time and therefore the increase of electrical consumption, that it should be need to increase the removal of MPs by UV-C treatments alone.

Degradation of dye Procion Red MX-5B by electrolytic and electro-irradiated technologies using diamond electrodes

This work focuses on the treatment of synthetic wastewater polluted with dye Procion Red MX-5B by different Electrochemical Advanced Oxidation Processes (EAOP) based on diamond anodes. The influence of the current density and the supporting electrolyte has been studied on dye removal and total mineralization of the organic matter. Results show that electrolysis with diamond electrodes is a suitable technology for an efficient degradation of dye. Nonetheless, the process efficiency increases when using chloride as supporting electrolyte because of the electrochemical generation of hypochlorite in wastewater which significantly contribute to dye removal. On the contrary, the total mineralization of the organic matter is more efficient in sulfate media. In this case, large amounts of peroxodisulfate are electrogenerated, favoring the complete removal of total organic carbon (TOC). On the other hand, lower current densities (10 mA cm^-2) lead to a more efficient removal of both dye and TOC due to the mass transfer limitations of the technology. Finally, the coupling of UV light irradiation or ultrasound to electrolysis significantly improves the process performance, being photoelectrolysis the most efficient technology for the treatment of wastewater polluted with Procion Red MX-5B. This fact is due to the potential production of free chlorine or sulfate radicals that takes place by the activation of the electrogenerated oxidants. These species are more reactive than oxidants and, therefore, they quickly attack the organic matter present in wastewater.