Electrolysis with diamond anodes: Eventually, there are refractory species!

Analysis of the degradation of m-cresol with Fe/AC in catalytic wet peroxide oxidation enhanced by swirl flow

Catalytic wet peroxide oxidation (CWPO) enhanced by swirl flow (SF-CWPO) was developed for the first time to explore the degradation of m-cresol in 3%iron/activated carbon catalysed Fenton reaction. Under the conditions of catalyst dosage of 0.6 g/L, H₂O₂ dosage of 1.5 mL/L, pH = 6 and reaction time of 20 min, the degradation rate of m-cresol and total organic carbon in 100 mg/L m-cresol solution reaches 81.5% and 82%, respectively. The reaction speed in the SF-CWPO system with an independently designed cyclone reactor was two times faster than the traditional CWPO systems. In addition, via liquid chromatography-mass spectrometry analysis of the degradation product, the possible degradation pathway for m-cresol was proposed. The proposed SF-CWPO can potentially be an efficient and economical method to treat organic pollutants in wastewaters.

Toward real applicability of electro-ozonizers: Paying attention to the gas phase using actual commercial PEM electrolyzers technology

This work focuses on increasing the TRL of electro-ozonizer technology by evaluating the effect of electrolyte composition and operation conditions on the production of ozone, using an actual commercial cell, CONDIAPURE®, in conditions similar to what could be expected in a real application. Not only is attention paid to the changes in the concentration of ozone in the liquid phase, but also to those observed in the gas phase. The electrolyte and its recirculation flowrate, as well as operation temperatures and pressures are found to have significant influence on production rates. The most efficient way to produce ozone is operating at low temperatures and high pressures. In this work, 0.25 and 0.21 mg O₃/min were obtained operating at 10 A in electrolytes consisting of aqueous solutions of perchloric and sulfuric acid, respectively, in tests carried out at 13 °C and 2 bars of gauge pressure. The negative effect of scavengers that appear electrochemically along the production of ozone is very important and seems to be partially compensated when organics are present in the solution due to the competition between the reaction of these scavengers with ozone or organics.

Does intensification with UV light and US improve the sustainability of electrolytic waste treatment processes?

This work aims to assess the influence of ultrasounds (US) application or ultraviolet (UV) light irradiation on the efficiency and sustainability of the treatment of wastes by conductive diamond electrochemical oxidation (CDEO). To do this, a life cycle assessment (LCA) is carried out in order to quantify the environmental impacts of the intensified CDEO processes. Inventories of three bench scale remediation plants (CDEO, Sono-CDEO and Photo-CDEO) in which the different technologies are implemented are performed by means of Ecoinvent 3.3 data base. AWARE, USEtox, IPPC and ReCiPe methodologies are used to quantify the environmental burden into 5 midpoint (water footprint, global warming 100a, ozone layer depletion, human toxicity, freshwater ecotoxicity) and 17 endpoint impact categories. Photo-CDEO attains the faster and more efficient removal in terms of energy consumed. All impact categories are lower in the case in which UV light irradiation is coupled to the CDEO treatment, particularly if the electrolyte does not contain chloride anions. From the point of view of toxicity and ecotoxicity, it is essential to achieve a complete mineralization, because of the intermediates generated into wastes containing chloride anions can become more hazardous than the initial pesticide. The operation of these technologies at large current densities shows positive results from the sustainability point of view, despite the huge environmental impact related to the energy production. Data notice that almost a 99.0% of the total global warming potential is mainly due to the electricity required during the electrochemical treatment, being higher by the sono and photo CDEO treatments because of the use of additional devices. Nevertheless, this issue can be overcome by means of using renewable energies as power sources of these remediation treatments. According to results, it can be claimed that the electrochemical technologies may successfully compete with other AOPs in terms of sustainability.

Influence of hydrodynamic conditions on the degradation of 1-butyl-3-methylimidazolium chloride solutions on boron-doped diamond anodes

This study assessed the influence of hydrodynamic conditions on the degradation process of 1-butyl-3-methylimidazolium chloride (BMImCl) solution on a boron-doped diamond anode in a filter-type electrochemical reactor configuration. The results show that this parameter did not significantly affect this process when operating in the laminar regime. However, in the transition regime (Re ≥ 2000), higher flow rates resulted in a faster removal of BMImCl and total organic carbon, making the process more efficient. Following BMImCl degradation, nitrates were generated at the cathode, then reduced at the cathode to ammonium; combination with free chloride produced at the anode led to the transformation of chloride into combined chlorine forms instead of more toxic oxianions such as chlorate and perchlorate. Thus, the flow rate can be a key parameter for defining operating conditions in which the target BMImCl is more effectively degraded with reduced generation of undesirable secondary products.

Removal of imidazolium-based ionic liquid by coupling Fenton and biological oxidation

In this work, we assessed the potential of combining Fenton´s reagent and biological oxidation for removing the imidazolium-based ionic liquid 1-Ethyl-3-methylimidazolium chloride (EmimCl). Fenton-like oxidation was conducted at variable H₂O₂ doses from 20 to 100% the stoichiometric value as calculated from the theoretical chemical oxygen demand (COD). The stoichiometric H₂O₂ dose afforded Total Organic Carbon (TOC) conversion and COD removal of 50 and 62%, respectively. Identifying the reaction by-products formed at low hydrogen peroxide doses allowed a plausible pathway for EmimCl oxidation to be proposed. The effluents from Fenton-like oxidation at substoichiometric H₂O₂ doses were less ecotoxic and more biodegradable than was the parent ionic liquid. The effluent from Fenton-like oxidation with the 60% H₂O₂ dose (TOC conversion ≅ 41%, COD removal ≅ 31%) was subsequently subjected to an effective biological treatment that allowed complete removal of the starting compound, increased its ecotoxicity to a low-moderate level and rendered it acceptably biodegradable. Biological oxidation was performed in 8-h and 12-h cycles in a sequencing batch reactor. Combining Fenton and biological oxidation of EmimCl afforded TOC conversion and COD removal of around 90%.

Heterogeneous electro-Fenton as plausible technology for the degradation of imidazolinium-based ionic liquids

Conventional water treatments are generally inadequate for degradation of emerging pollutants such as ionic liquids (ILs). The use of heterogeneous electro-Fenton (HEF) has attracted great interest, due to its ability to efficiently oxidize a wide range of organic pollutants operating in cycles or in continuous mode. In this study, the removal of a complex IL from the imidazolinium family (1,3-Bis(2,4,6-trimethylphenyl)imidazolinium chloride), by means of HEF using iron alginate spheres as catalyst has been investigated, resulting in significant TOC decay after 6 h. The optimization of the key process parameters (current, IL concentration and catalyst dosage) has been performed using a Box-Behnken experimental design and achieving 76.98% of TOC abatement in 2 h of treatment. Current proved to be a crucial parameter and high catalyst dosage is required to achieve the maximum removal. In addition, an insight about the availability of iron into the reactor and the evolution of several intermediates has been carried out by employing differential pulse voltammetry on screen-printed carbon electrodes. The evolution of the different voltammetric peaks confirmed the influence of iron release, and the generation of several iron complexes has permitted the comprehension of the degradation pathway, which has been validated by chromatographic techniques.