Long-range transport potential and atmospheric persistence of cyclic volatile methylsiloxanes based on global measurements

Interference of the gas chromatography- mass spectrometry instrumental background on the determination of trace cyclic volatile methylsiloxanes and exclusion of it by delayed injection

Cyclic volatile methylsiloxanes (cVMS) have been widely found in various types of environmental media and attracted increasing attention as new pollutants. However, there is still a great challenge in the accurate quantification of trace cVMS, due to their volatility, and the high background originating from GC/MS accessories and surroundings. In this work, the main sources of the high background were investigated in detail for octamethylcyclotetrasiloxane (D4), decmethylcyclopentasiloxane (D5) and dodecmethylcyclohexosiloxane (D6). Several effective measures were employed to minimize these backgrounds, including the delayed injection method to minimize the interference from the injection septum. Then, a GC-MS method was developed for the accurate determination of D4, D5 and D6, with a linear range of 2 - 200 μg/L. The coefficient of determination was 0.9982-0.9986, the limit of detection (LOD) was 0.40-0.52 μg/L, and the quantitative range was 1.88-190 μg/L. Good reproducibility and recovery were obtained, indicating the reliability of the established analytical method.

Cyclic volatile methyl siloxanes (D4, D5, and D6) as the emerging pollutants in environment: environmental distribution, fate, and toxicological assessments

Cyclic volatile methyl siloxanes (cVMS) have now become a subject of environmental contamination and risk assessment due to their widespread use and occurrence in different environmental matrices. Due to their exceptional physio-chemical properties, these compounds are diversely used for formulations of consumer products and others implying their continuous and significant release to environmental compartments. This has captured the major attention of the concerned communities on the grounds of potential health hazards to human and biota. The present study aims at comprehensively reviewing its occurrence in air, water, soil, sediments, sludge, dusts, biogas, biosolids, and biota and their environmental behavior as well. Concentrations of cVMS in indoor air and biosolids were higher; however, no significant concentrations were observed in water, soil, and sediments except for wastewaters. No threat to the aquatic organisms has been identified as their concentrations do not exceed the NOEC (maximum no observed effect concentration) thresholds. Mammalian (rodents) toxicity hazards were not very evident except for the occurrence of uterine tumors in very rare cases under long-term chronic and repeated dose exposures in laboratory conditions. Human relevancy to rodents were also not strongly enough established. Therefore, more careful examinations are required to develop stringent weight of evidences in scientific domain and ease the policy making with respect to their production and use so as to combat any environmental consequences.

Dimethylsiloxanes in dust from nine indoor microenvironments of Henan Province: Occurrence and human exposure assessment

Dimethylsiloxanes (MSs) are widely used in daily life and industry, with indoors being the main release site. Detecting the levels of MSs in indoor dust is essential for assessing the risks of human exposure. In this study, the content of MSs (D3-D8 and L3-L16) was quantified in indoor dust samples from nine microenvironments of Henan Province. The detection frequency of the targets ranged from 5.00 % to 100 %. The sum concentration of dimethylsiloxanes (TSi) was in a range of 463-3.32 × 104 ng·g-1 (median: 1.92 × 103 ng·g-1). The sum concentration of linear dimethylsiloxanes (TLSi) from all microenvironments was higher than the sum concentration of cyclic dimethylsiloxanes (TCSi), which was consistent with previously reported results. D7 and D8 were the main cyclic dimethylsiloxane, which had similar sources based on Spearman correlation analysis (p < 0.001). Moreover, D8 was detected with high levels in indoor dust for the first time, which warrants further exploration. L8-L16 were the main linear dimethylsiloxanes, which may have been due to their widespread use in electronic equipment and office equipment. The Spearman analysis found that total organic carbon (TOC) in indoor dust had weak effect on MSs. Additionally, relatively high MS levels were recorded in high people-flow working microenvironments. Accordingly, the exposure doses of MSs via indoor dust intake were estimated for different age groups using the model of worst-case exposure and median concentration. Toddlers had the highest EDIs (95th percentile concentration, 90.7 ng·kg-1-bw·d-1) to MSs.

Per- and polyfluoroalkyl substances and volatile methyl siloxanes in global air: Spatial and temporal trends

The study reports on the atmospheric concentrations of per- and polyfluoroalkyl substances (PFAS) and volatile methyl siloxanes (VMS) measured using sorbent-impregnated polyurethane foam disks (SIPs) passive air samplers. New results are reported for samples collected in 2017, which extends temporal trend information to the period 2009-2017, for 21 sites where SIPs have been deployed since 2009. Among neutral PFAS, fluorotelomer alcohols (FTOHs) had higher concentrations than perfluoroalkane sulfonamides (FOSAs) and perfluoroalkane sulfonamido ethanols (FOSEs) with levels of ND‒228, ND‒15.8, ND‒10.4 pg/m³, respectively. Among ionizable PFAS, the sum of perfluoroalkyl carboxylic acids (PFCAs) and perfluoroalkyl sulfonic acids (PFSAs) in air were 0.128-781 and 6.85-124 pg/m³, respectively. Longer-chain i.e. C₉-C₁₄ PFAS, which are relevant to the recent proposal by Canada for a listing of long-chain (C₉-C₂₁) PFCAs to the Stockholm Convention, were also detected in the environment at all site categories including Arctic sites. Cyclic and linear VMS ranged between 1.34‒452 and 0.01-12.1 ng/m³, respectively, showing dominance in urban areas. Despite the wide range of levels observed across different site categories, geometric means of the PFAS and VMS groups were fairly similar when grouped according to the five United Nations regions. Variable temporal trends in air (2009-2017) were observed for both PFAS and VMS. PFOS, which has been listed in the Stockholm Convention since 2009, is still showing increasing tendencies at several sites, indicating constant input from direct and/or indirect sources. These new data inform international chemicals management for PFAS and VMS.

Seasonal and latitudinal variability in the atmospheric concentrations of cyclic volatile methyl siloxanes in the Northern Hemisphere

Field data from two latitudinal transects in Europe and Canada were gathered to better characterize the atmospheric fate of three cyclic methylsiloxanes (cVMSs), i.e., octamethyl-cyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5) and dodecamethylcyclohexasiloxane (D6). During a year-long, seasonally resolved outdoor air sampling campaign, passive samplers with an ultra-clean sorbent were deployed at 15 sampling sites covering latitudes ranging from the source regions (43.7-50.7 °N) to the Arctic (79-82.5 °N). For each site, one of two passive samplers and one of two field blanks were separately extracted and analyzed for the cVMSs at two different laboratories using gas-chromatography-mass spectrometry. Whereas the use of a particular batch of sorbent and the applied cleaning procedure to a large extent controlled the levels of cVMS in field blanks, and therefore also the method detection and quantification limits, minor site-specific differences in field blank contamination were apparent. Excellent agreement between duplicates was obtained, with 95% of the concentrations reported by the two laboratories falling within a factor of 1.6 of each other. Nearly all data show a monotonic relationship between the concentration and distance from the major source regions. Concentrations in source regions were comparatively constant throughout the year, while the concentration gradient towards remote regions became steeper during summer when removal via OH radicals is at its maximum. Concentrations of the different cVMS oligomers were highly correlated within a given transect. Changes in relative abundance of cVMS oligomers along the transect were in agreement with relative atmospheric degradation rates via OH radicals.

Atmospheric Degradation of Cyclic Volatile Methyl Siloxanes: Radical Chemistry and Oxidation Products

Cyclic volatile methyl siloxanes (cVMS) are anthropogenic chemicals that have come under scrutiny due to their widespread use and environmental persistence. Significant data on environmental concentrations and persistence of these chemicals exists, but their oxidation mechanism is poorly understood, preventing a comprehensive understanding of the environmental fate and impact of cVMS. We performed experiments in an environmental chamber to characterize the first-generation oxidation products of hexamethylcyclotrisiloxane (D3), octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5) under different peroxy radical fates (unimolecular reaction or bimolecular reaction with either NO or HO₂) that approximate a range of atmospheric compositions. While the identity of the oxidation products from D3 changed as a function of the peroxy radical fate, the identity and yield of D4 and D5 oxidation products remained largely constant. We compare our results against the output from a kinetic model of cVMS oxidation chemistry. The reaction mechanism used in the model is developed using a combination of previously proposed cVMS oxidation reactions and standard atmospheric oxidation radical chemistry. We find that the model is unable to reproduce our measurements, particularly in the case of D4 and D5. The products that are poorly represented in the model help to identify possible branching points in the mechanism, which require further investigation. Additionally, we estimated the physical properties of the cVMS oxidation products using structure-activity relationships and found that they should not be significantly partitioned to organic or aqueous aerosol. The results suggest that cVMS first-generation oxidation products are also long-lived in the atmosphere and that environmental monitoring of these compounds is necessary to understand the environmental chemistry and loading of cVMS.

Measuring snow scavenging of two airborne cyclic volatile methylsiloxanes under controlled conditions

The objective of this study was to determine snow scavenging of cVMS and its potential effect on the cVMS concentrations in snowmelt water and surrounding soil. Snow scavenging of two cVMS, octamethylcyclotetrasiloxane (D4) and decamethylcyclopentasiloxane (D5), was examined in two steps. First, sorption and desorption of D4 and D5 on snowflakes, including snow sorption coefficients (K_iA), were measured against a benchmark compound, cyclopentanone, at different temperatures from 0 to -20 °C. Measurements were made using a custom-made snow chamber and ¹⁴C-labeled D4 and D5. In addition, the transfer of snow-bound cVMS to snowmelt water and surrounding soil was studied with ¹⁴C-D4 and ¹⁴C-D5-spiked snowpack placed both in a closed snow chamber and on top of a layer of frozen soil in an open chemical hood. K_iA values measured in both sorption and desorption processes were very small (<10^-2 m). They increased with decreasing temperature and were higher for the D5 compared to D4. The calculated gas scavenging of D4 and D5 was small because of the small K_iA values, while particle scavenging of cVMS is predicted to be negligible due to their low octanol/air partition coefficients (K_OA). Most importantly, almost all ¹⁴C-D4 and ¹⁴C-D5 sorbed by a snowpack was lost during the snow melting process through re-volatilization and hydrolysis and became non-detectable in snowmelt water. In short, the experimental measurements demonstrated that snow scavenging could not be a valid deposition mechanism for these volatile hydrophobic compounds.

A Mini-Review on Recent Developments in Anti-Icing Methods

An aggressive impact of the formed ice on the surface of man-made objects can ultimately lead to serious consequences in their work. When icing occurs, the quality and characteristics of equipment, instruments, and building structures deteriorate, which affects the durability of their use. Delays in the adoption of measures against icing endanger the safety of air travel and road traffic. Various methods have been developed to combat de-icing, such as mechanical de-icing, the use of salts, the application of a hydrophobic coating to the surfaces, ultrasonic treatment and electric heating. In this review, we summarize the recent advances in the field of anti-icing and analyze the role of various additives and their operating mechanisms.

Distribution of cyclic volatile methylsiloxanes in drinking water, tap water, surface water, and wastewater in Hanoi, Vietnam

In this study, four cyclic volatile methylsiloxanes (cVMSs) were determined in drinking water, tap water, surface water, and wastewater samples collected from Hanoi metropolitan area, Vietnam, during August to December 2020 (dry season) by using solid phase extraction combined with gas chromatography tandem mass spectrometry. Highest concentrations of cVMSs in the range of 63-7400 ng/L (mean/median: 1840/1310 ng/L) were found in wastewater samples. A significant difference existed in the concentrations of cVMSs between influent and effluent of a wastewater treatment plant. The sum concentrations of four cVMSs in lake water, tap water, and bottled water samples were in the ranges of 67.0-1100 ng/L (mean/median: 350/282 ng/L), 19.8-350 ng/L (12.6/12.3 ng/L), and 2.31-28.1 ng/L (10.3/8.23 ng/L), respectively. Among the four cVMSs, decamethylcyclopentasiloxane (D5) was found at the highest concentrations in all water samples analyzed. The mean exposure doses of cVMSs calculated for adults and children through the consumption of drinking were 0.409 and 0.412 ng/kg-bw/day, respectively. Human exposure to cVMSs calculated through drinking water consumption was significantly lower than that reported for inhalation.

Review of recent findings on occurrence and fates of siloxanes in environmental compartments

In view of their vast global usage in both consumer products and industrial processes, environmental emission and fates of siloxanes have become concerned issue. This review summarized the research progress, especially in the last decade, on production/consumption data, toxicities, analysis methods, environmental distribution, migration and degradation/transformation of both dimethylsiloxanes and modified siloxanes in atmospheric, aquatic and terrestrial compartments from various areas (especially in China). In spite of their fast degradation (hydrolysis and hydroxylation, etc) in various matrices (except sediment), dimethylsiloxane oligomers have been found in various environmental matrices from many countries due to their constant usage and emission. Moreover, recent literatures have paid attention to behaviors of dimethylsiloxanes in industrial areas, e.g., their higher residual levels compared with residential areas and unique transformed products (such as halogenated products) arose from special industrial production scenarios. Meanwhile, although most prior studies focused on dimethylsiloxanes, identification of modified-siloxanes with other functional groups in environment have been beginning to attract the attention of scientists. Furthermore, related literatures indicated that compared with dimethylsiloxanes, both halogenated-dimethylsiloxanes and modified methylsiloxanes (phenylsiloxanes and trifluoropropylsiloxanes) could have stronger persistence due to their weaker volatilization and degradation, especially in terrestrial matrices.

Methylsiloxane occurrence and distribution in free-range poultry eggs near a rural industrial park: Indicators of potential risks to birds

The ecological harm from methylsiloxanes has drawn worldwide attention. This study investigated three cyclic (D₄-D₆) and four linear siloxanes (L₇-L₁₀) in the eggs of free-range poultry collected near a rural industrial park in China and found total concentrations in the range of 19.2-1204 (median, 268) ng/g dry weight. Higher concentrations of methylsiloxanes were observed in chicken eggs than duck eggs. Cyclic siloxanes represented a median of 62.2% of the total methylsiloxane concentrations. A source assessment indicated that local soils and outdoor dust were more important sources of egg methylsiloxanes than poultry food. The partitioning of methylsiloxanes between egg yolk and egg albumen was investigated, and preferential distributions of the chemicals in the yolk were observed. This study confirmed that methylsiloxanes were highly prevalent in the study poultry eggs. The results suggested that the potential risks to some wild birds inhabiting this area should be of concern, as their physiologies and feeding ecologies are similar to those of the studied poultry, although available ecotoxicological data of the chemicals to birds remains scarce. Additional research is needed to characterize the accumulation of methylsiloxanes in different bird species and its associated adverse effects on their offspring.

Comment on "Optimization of suspect and non-target analytical methods using GC/TOF for prioritization of emerging contaminants in the Arctic environment"

Lee et al. (2019) recently proposed that volatile methylsiloxanes (VMS) be considered as emerging contaminants in the Arctic environment based on the results of suspect and non-target screening of environmental samples collected from Ny-Ålesund, Svalbard. In any analytical program, it is of critical importance to be able to discern if the identification of analytes is due to true presence in the sampled environmental media or if contamination occurred during sample handling and analysis, leading to false positive detection. This is particularly important for VMS due to their ubiquity in consumer products, sample containers, and analytical instrumentation, thus requiring robust quality control (QC) procedures to support the validity of results. Although Lee et al. (2019) concluded that VMS in the environmental samples originated from potential long-range transport and deposition, it is most likely that local point sources account for their presence. Additionally, there is low confidence in the validity of the reported detection of VMS in the sampled environmental media as this study does not include any of the necessary QC to determine whether the VMS detected would be due to contamination or indicative of presence in the environment.

Development of a New Passive Sampling Method for the Measurement of Atmospheric Linear and Cyclic Volatile Methyl Siloxanes

A new passive sampling method was developed and characterized to measure atmospheric volatile methyl siloxanes (VMS). The infrastructure of a commercial passive air sampler (PAS) was used along with XAD-2 resin as the adsorbent. Experimental sampling rates (SR) determined using collocated active and passive samplers ranged between 0.0363 (L5) and 0.0561 (D3) m³/day and agreed well with the theoretical ones. VMS uptake was highly linear for eight weeks. The precision of the method was very good (<10%). Compared to the other PASs used for VMS, the new method has several advantages (i.e., the sampler is much smaller, it has commercially available components, and the solvent requirement, equipment needed for extraction, and steps for sample preparation are minimal) while achieving similar or lower method detection limits. The developed method was applied to investigate the spatial distribution and possible sources of atmospheric VMS in the Izmir region. Field sampling covered 42 sites representing different source and land use areas. ΣVMS concentrations ranged between 41.4 and 981 ng/m³. The dominant VMS was D5 followed by D3 and D4. Spatial distributions indicated that the main VMS sources in the area were urban areas, wastewater treatment plants, and landfills where the VMS-containing products are used and disposed.

Reducing sampling artifacts in active air sampling methodology for remote monitoring and atmospheric fate assessment of cyclic volatile methylsiloxanes

Active sampling methodology for atmospheric monitoring of cyclic volatile methylsiloxanes (cVMS) was improved to reduce sampling artifacts. A new sorbent, ABN Express (ABN), was evaluated for storage stability and measurement accuracy. Storage stability of cVMS on ABN showed less than 1% degradation of the individual ¹³C-labelled octamethylcyclotetrasiloxane (¹³C₄-D4), decamethylcyclopentasiloxane (¹³C₅-D5) and dodecamethylcyclohexasiloxane (¹³C₆-D6) after 14 days storage at room temperature and at -20 °C whereas significant degradation was observed on ENV+ sorbent at room temperature (37-62 %) and -20 °C (9-16 %). ¹³C₄-D4 formed on ENV+ spiked with ¹³C₅-D5, and both ¹³C₄-D4 and ¹³C₅-D5 formed on ENV+ spiked with ¹³C₆-D6. However, this was not observed on the ABN sorbent. Performance of ABN was compared to ENV+ through an 8-month Arctic sampling campaign at the Zeppelin Observatory (Ny Ålesund, Svalbard). Good agreement between ABN and ENV+ was observed for D4 in the spring/summer months. However, D5 and D6 was found to be consistently higher on the ABN sorbent during this time period with D6 showing the greatest deviation. During the winter months, larger deviations were observed between ABN and ENV+ sorbents with a factor of 4 times higher atmospheric concentrations of both D5 and D6 found on ABN; indicating sorbent related degradation on ENV+. Our findings show that the ABN sorbent provides greater stability and accuracy for atmospheric monitoring of cVMS. Implications of these improvements towards atmospheric fate processes will be discussed.

Atmospheric Chemistry of Volatile Methyl Siloxanes: Kinetics and Products of Oxidation by OH Radicals and Cl Atoms

Volatile methyl siloxanes (VMS) are ubiquitous anthropogenic pollutants that have recently come under scrutiny for their potential toxicity and environmental persistence. In this work, we determined the rate constants for oxidation by OH radicals and Cl atoms at 297 ± 3 K and atmospheric pressure in Boulder, CO (∼860 mbar) of hexamethyldisiloxane (L2), octamethyltrisiloxane (L3), decamethyltetrasiloxane (L4), dodecamethylpentasiloxane (L5), hexamethylcyclotrisiloxane (D3), octamethylcyclotetrasiloxane (D4), and decamethylcyclopentasiloxane (D5). Measured rate constants with OH radicals were (1.20 ± 0.09) × 10^-12, (1.7 ± 0.1) × 10^-12, (2.5 ± 0.2) × 10^-12, (3.4 ± 0.5) × 10^-12, (0.86 ± 0.09) × 10^-12, (1.3 ± 0.1) × 10^-12, and (2.1 ± 0.1) × 10^-12 cm³ molec^-1 s^-1, for L2, L3, L4, L5, D3, D4, and D5, respectively. The rate constants for reactions with Cl atoms with the same compounds were (1.44 ± 0.05) × 10^-10, (1.85 ± 0.05) × 10^-10, (2.2 ± 0.1) × 10^-10, (2.9 ± 0.1) × 10^-10, (0.56 ± 0.05) × 10^-10, (1.16 ± 0.08) × 10^-10, and (1.8 ± 0.1) × 10^-10 cm³ molec^-1 s^-1, respectively. Substituent factors of F(-Si(CH₃)₂OR) and F(-SiCH₃(OR)₂) are proposed for use in AOPWIN, a common model for OH radical rate constant estimations. Cl atoms can remove percentage levels of VMS globally with potentially increased importance in urban areas.

A review of contamination status, emission sources, and human exposure to volatile methyl siloxanes (VMSs) in indoor environments

Siloxanes are organo-silicon compounds containing Si-O-Si linkages and methyl branches. Depending on the structure, siloxanes can be divided into cyclic and linear compounds. Methyl siloxanes with small and medium molecular weights (molecular weights less than 500 g mol^-1), are volatile under normal conditions, and hence are referred to as volatile methyl siloxanes (VMSs). VMSs are additive ingredients in many products such as plastics, rubber, personal care products, and household items. This review provides information on the distribution of VMSs in consumer products, indoor air and dust, and their implications for human exposure. VMSs have been used in personal care products and household items at concentrations on the order of hundreds to thousands of micrograms per gram which are the main sources of contamination in the indoor environments. VMSs have been found widely in indoor air and dust. A significant correlation existed between VMS concentrations in indoor air and dust. Among typical VMSs, dodecamethylcylcopentasiloxane (D5) is the major compound found in indoor environments. The human exposure doses to VMSs through dermal absorption, dust ingestion, and inhalation were compiled; Inhalation is a dominant pathway of exposure to VMSs, especially in indoor environments of occupational settings like hair salons. The human exposure doses were higher in children than in adults.