The effects of carbon disulfide driven functionalization on graphene oxide for enhanced Pb(II) adsorption: Investigation of adsorption mechanism

Carbon Dot-Stabilized Hydrogel Composite: A New Adsorbent for Efficient and Sustainable Pb(II) Removal

In this paper, a carbon dot hydrogel composite (CDs-Hy) capable of efficiently removing Pb(II) was prepared by hydrogen bonding self-assembly in combination with carbon dots and a hydrogel. CDs-Hy was characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS), and the effect of the adsorption conditions on the adsorption efficiency of CDs-Hy was studied. The results of the study showed that the incorporation of carbon dots, on the one hand, significantly increased the adsorption capacity of the material. On the other hand, it can increase the stability of hydrogels in aqueous solution. The possible adsorption mechanisms were further verified as ion exchange and coordination. CDs-Hy is a novel adsorbent material capable of removing Pb2+ efficiently, which can be reused several times with high stability.

Experimental and computational studies of crystal violet removal from aqueous solution using sulfonated graphene oxide

Positively charged contaminants can be strongly attracted by sulfanilic acid-functionalized graphene oxide. Here, sulfonated graphene oxide (GO-SO3H) was synthesized and characterized for cationic crystal violet (CV) adsorption. We further studied the effect of pH, initial concentration, and temperature on CV uptake. The highest CV uptake occurred at pH 8. A kinetic study was also carried out by applying the pseudo-first-order and pseudo-second-order models. The pseudo-second-order's adsorption capacity (qe) value was much closer to the experimental qe (qeexp:0.13, qecal:0.12) than the pseudo-first-order model (qeexp:0.13, qecal:0.05). The adsorption performance was accomplished rapidly since the adsorption equilibrium was closely obtained within 30 min. Furthermore, the adsorption capacity was significantly increased from 42.85 to 79.23%. The maximum adsorption capacities of GO-SO3H where 97.65, 202.5, and 196.2 mg·g-1 for CV removal at 298, 308, and 328 K, respectively. The Langmuir and Freundlich adsorption isotherms were applied to the experimental data. The data fit well into Langmuir and Freundlich except at 298 K, where only Langmuir isotherm was most suitable. Thermodynamic studies established that the adsorption was spontaneous and endothermic. The adsorption mechanism was revealed by combining experimental and computational methods. These findings suggest that GO-SO3H is a highly adsorbent for removing harmful cationic dye from aqueous media.

Ethanol-mediated synthesis of γ-cyclodextrin-based metal-organic framework as edible microcarrier: performance and mechanism

Here, an ethanol-mediated method was introduced to fabricate γ-cyclodextrin-based metal-organic frameworks (γ-CD-MOFs) as microcarriers for epigallocatechin-3-gallate (EGCG). Through adjusting ethanol gas diffusion temperature and ethanol liquid feed speed, we achieved control of crystallization efficiency and crystals size without extra surfactants. Under the sequential regulatory by ethanol in two phases, the obtained γ-CD-MOFs with cubic shape exhibited excellent crystallinity, high surface area, and uniform size distribution. Through the interplay of hydrogen bonding, hydrophobic interactions and π stacking, EGCG molecules could be stored efficiently within cavities and tunnels of the γ-CD-MOFs with high load capability of 334 mg g^-1. More importantly, the incorporation of EGCG within frameworks wouldn't disintegrate the unique body-centered cubic structure of γ-CD-MOFs, in turn, would improve the thermostability and antioxidative activity of EGCG. Significantly, all food-grade materials ensured the γ-CD-MOFs high acceptance and applicability for food and biomedical applications.

An ultra-sensitive and selective electrochemical sensor based on GOCS composite and ion imprinted polymer for the rapid detection of Cd2+ in food samples

An ultra-sensitive and selective electrochemical sensor was proposed through the combination of carbon disulfide-functionalized graphene oxide (GOCS) composite with high conductivity and cadmium ion-imprinted polymer (IIP). Using pyrrole as the functional monomer and Cd²⁺ as the template ion, the IIP was formed by in situ electropolymerization on GOCS composite. Under the optimized experimental conditions, the sensor exhibited a good linear relationship in the range of 0.5-50 μg/L Cd²⁺ concentration, with the lowest detection limit of 0.23 μg/L. The sensor exhibited not only good selectivity for the determination of Cd²⁺, but also good repeatability with current response remaining 87.6 % after four cycles. Furthermore, the sensor exhibited similar sensing performance in lettuce, orange and peach with recovery ranging from 82.6 % to 110.63 %. This work is expected to provide an electrochemical sensor with excellent selectivity, good stability and sensitivity for the detection of trace amounts of Cd²⁺ in real samples.

Adsorption of Pb(II) from wastewater using a red mud modified rice-straw biochar: Influencing factors and reusability

Efficient environmental remediation of toxic chemicals using effective sorbents has received considerable attention recently. For the present study, the synthesis of a red mud/biochar (RM/BC) composite was performed from rice straw with the aim of achieving Pb(II) removal from wastewater. Characterization was performed by using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), energy dispersive spectroscopy (EDS), Zeta potential analysis, elemental mapping, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Results showed that RM/BC had higher specific surface area (S_BET = 75.37 m² g^-1) than raw biochar (S_BET = 35.38 m² g^-1). The Pb(II) removal capacity (q_e) of RM/BC was 426.84 mg g^-1 at pH 5.0, and the adsorption data well fitted pseudo second order kinetics (R² = 0.93 and R² = 0.98), as well as the Langmuir isotherm model (R² = 0.97 and R² = 0.98) for both BC and RM/BC. Pb(II) removal was slightly hindered with the increasing strength of co-existing cations (Na⁺, Cu²⁺, Fe³⁺, Ni²⁺, Cd²⁺). The increase in temperatures (298 K, 308 K, 318 K) favored Pb(II) removal by RM/BC. Thermodynamic study indicated that Pb(II) adsorption onto BC and RM/BC was spontaneous and primarily governed by chemisorption and surface complexation. A regeneration study revealed the high reusability (>90%) and acceptable stability of RM/BC even after five successive cycles. These findings indicate that RM/BC evidenced special combined characteristics of red mud and biochar, hence its use for Pb removal from wastewater offers a green and environmentally sustainable approach fitting the "waste treating waste" concept.

Simultaneous adsorption of As(III) and Pb(II) by the iron-sulfur codoped biochar composite: Competitive and synergistic effects

Simultaneous elimination of As(III) and Pb(II) from wastewater is still a great challenge. In this work, an iron-sulfur codoped biochar (Fe/S-BC) was successfully fabricated in a simplified way and was applied to the remediate the co-pollution of As(III) and Pb(II). The positive enthalpy indicated that the adsorption in As-Pb co-pollution was an endothermic reaction. The mechanism of As(III) removal could be illustrated by surface complexation, oxidation and precipitation. In addition to precipitation and complexation, the elimination mechanism of Pb(II) also contained ion exchange and electrostatic interactions. Competitive and synergistic effects existed simultaneously in the co-contamination system. The suppression of As(III) was ascribed to competitive complexation of the two metals on Fe/S-BC, while the synergy of Pb(II) was attributed to the formation of the PbFe₂(AsO₄)₂(OH)₂. Batch experiments revealed that Fe/S-BC had outstanding ability to remove As(III) and Pb(II), regardless of pH dependency and interference by various coexisting ions. The maximum adsorption capacities of the Fe/S-BC for As(III) and Pb(II) were 91.2 mg/g and 631.7 mg/g, respectively. Fe/S-BC could be treated as a novel candidate for the elimination of As(III)-Pb(II) combined pollution.

Efficient visual adsorption of Pb2+ by nanocellulose/sodium alginate microspheres with fluorescence sensitivity

In this study, carbon dots (CDs) were prepared by a one-pot hydrothermal method using tempo-oxidized cellulose nanocrystals (TOCNC) and polyethylenimine (PEI). The CDs were self-assembled with a microsphere adsorbent prepared using TOCNC and sodium alginate (SA). CDs-TOCNC/SA-an environmentally friendly, fluorescent-sensitive, and recyclable microsphere adsorbent-was obtained. FTIR analysis showed that PEI successfully modified the CDs. In addition, the fluorescence quenching of CDs was observed when the concentration of Pb²⁺ was 0.0001-100 mg/L, indicating that CDs can dynamically monitor Pb²⁺. CDs-TOCNC/SA can produce blue fluorescence under 365 nm UV light and selectively and efficiently adsorb Pb²⁺. When the concentration of Pb²⁺ was 0.0001-100 mg/L, fluorescence quenching of the adsorbent was observed, indicating that CDs-TOCNC/SA could visually adsorb Pb²⁺. The adsorption isotherm and kinetic parameters show that the adsorption process conforms to the Langmuir isotherm model at 298 K, and the maximum adsorption capacity of Pb²⁺ was 190.1 mg/g at pH = 5. Moreover, CDs-TOCNC/SA could still obtain 78.99 % Pb²⁺ after five sorption-desorption cycles. The adsorption mechanism may involve ion exchange, electrostatic attraction, intra-particle diffusion, and chemical complexation.

Synthesis of Fe-THC MOFs and functionalizing MOFs by MXenes for the selective removal of lead(ii) ions from wastewater

The elimination of heavy metals, especially lead, from wastewater is vital for the environment and human health and using a proper adsorbent to achieve this goal is highly desirable. Initially, Fe-THC MOF was prepared using a simple method and functionalized using MXene for efficient, rapid, and selective elimination of lead. Different characterization tools demonstrated that Fe-THC MOF and its composite Fe-THC/MXene were successfully prepared. The adsorption outcomes showed that the maximum sorption capability was 674 mg g^-1 at 305 K and pH 4.5. The sorption kinetics obeys the pseudo-second-order kinetic model, and the sorption isotherms fit the Langmuir isotherm model. This finding suggests monolayer sorption on Fe-THC/MXene, and the rate-controlling step is chemisorption. Thermodynamic findings exhibit that sorption was a spontaneous and exothermic process. The sorption process can selectively adsorb Pb ions from aqueous media. After five adsorption-desorption tests, the adsorption efficiency of Fe-THC/MXene was still high. The sorption mechanism of lead on Fe-THC was mainly due to the interaction of lead ions with -F and -O ions and porosity of the Fe-THC/MXene composite. The -O and -F ions were derived from MXene, while the porosity was derived from the MOFs of composites. These findings confirmed that Fe-THC/MXene enables rapid, efficient, and selective elimination of lead from wastewater, which is of practical importance.

Removal of perfluorooctanoic acid via polyethyleneimine modified graphene oxide: Effects of water matrices and understanding mechanisms

This research aimed to evaluate the adsorption behaviors and mechanisms of perfluorooctanoic acid (PFOA) onto polyethyleneimine modified graphene oxide (GO-PEI) from aqueous solutions. The adsorption capacity was significantly improved by doping polyethyleneimine (PEI) onto graphene oxide (GO). The Brunauer-Emmett-Teller (BET) isotherm model was considered as the best isotherm model in describing the PFOA adsorption onto GO-PEI3 (w_PEI/w_GO = 3). GO-PEI3 exhibited high adsorption capacity (q_e = 368.2 mg/g, calculated from BET isotherm model) and excellent stability. The maximum monolayer amount of PFOA adsorption onto GO-PEI3 (q_m = 231.2 mg/g) was successfully evaluated. The calculated saturated concentration (C_s = 169.9 mg/L) of PFOA on GO-PEI3 closely agrees with its critical micelle concentration (CMC = 157.0 mg/L), suggesting the formation of multilayer hemi-micelles or micelles PFOA structures on the surface of GO-PEI3. PFOA adsorption onto GO-PEI3 was inhibited by several factors including: the presence of humic acid (HA) by competing with the adsorption sites, background salts through the double-layer compression effect, and the competition from soluble ions for the amine or amide functional groups on GO-PEI3. Finally, both the FT-IR and XPS results confirmed that the adsorption of PFOA onto GO-PEI3 was through electrostatic attraction and hydrophobic interaction (physical adsorption), but not chemical adsorption. This work provides fundamental knowledge both in understanding the adsorption behavior through the BET isotherm model and in developing a stable adsorbent for PFOA adsorption. In addition, the findings highlight the potential of PFOA remediation from wastewater systems using GO-PEI in engineering applications.

Electrochemical regeneration of granular activated carbon using an AQS (9,10- anthraquinone-2-sulfonic acid)/PPy modified graphite plate cathode

In the present study, we investigate the regeneration efficiency of Rhodamine B (RhB)-saturated granular activated carbon (GAC) in an electrochemical regeneration system by using a 9,10-anthraquinone-2-sulfonic acid/polypyrrole modified graphite plate (AQS/PPy-GP) cathode. The response surface methodology based on the Box-Behnken design (RSM-BBD) approach was used to optimize regeneration parameters, whereby the optimum condition of the independent variables was as follows: applied current = 155 mA, concentration of supporting electrolyte = 0.13 M, and regeneration time = 7 h. The electrochemical regeneration system with the AQS/PPy-GP electrode achieved high regeneration efficiency and significantly reduced energy consumption. H₂O₂ concentration generated in the electrolysis system was notably increased, and the time of complete degradation of organics was shortened by 25% compared to the electrode without modification. The mechanism for RhB degradation was proposed as AQS acting as a catalyst to promote the formation of H₂O₂. The regeneration study showed that AQS/PPy-GP cathode had appreciable reusability for GAC regeneration with a regeneration efficiency of 76.6% after 8 regeneration cycles. In summary, the electrochemical regeneration based on AQS/PPy-GP cathode would have practical industrial applications in treating spent activated carbons.

Novel GO/Fe-Mn hybrid for the adsorptive removal of Pb(II) ions from aqueous solution and the spent adsorbent disposability in cement mix: compressive properties and leachability study for circular economy benefits

GO/Fe-Mn hybrids were prepared by a single-pot chemical precipitation method and were characterized using FTIR, XRD, Raman, zeta potential, and FESEM, which confirmed the impregnation of Fe/Mn onto GO sheets. The synthesized hybrids were successively applied in removing the Pb(II) ions from aqueous solution and later utilizing the spent adsorbent to increase the properties of cement. The adsorption capability of the synthesized hybrid was seen in a set of batch studies to find out that about 15 min of contact time was required to remove 99% of the contaminant at a pH of 5 ± 0.2 and a dose of 0.83 g/L. The mechanism of the adsorption process for the synthesized hybrid was well described by Elovich kinetic model with an R² of 0.99 and Langmuir isotherm model, also with an R² of 0.99. The desorption studies conducted using 0.1 M HCl solution showed significant stability of the hybrid with a drop of 12% in the removal efficiency of Pb after up to five adsorption-desorption cycles. This points to an efficient adsorbent having potential for economical use. Later, the spent adsorbent was mixed with cement at ratios of 0.05%, 0.1%, and 0.5%, and compressive strength tests were performed, which showed an increase in the strength by 7.62%, 16.11%, and 26.82% at 28 days of curing time. The TCLP and SPLP tests performed on the hybrid and cement-spent adsorbent mix showed all the leaching parameters were well within the permissible limits. This development shows the potential for the use of spent adsorbent in a circular economy model.

Synthesis of Functionalized Carboxylated Graphene Oxide for the Remediation of Pb and Cr Contaminated Water

With the growing scarcity of water, the remediation of water polluted with heavy metals is the need of hour. The present research work is aimed to address this problem by adsorbing heavy metals ions (Pb (II) and Cr (VI)) on modified graphene oxide having an excess of carboxylic acid groups. For this, graphene oxide (GO) was modified with chloroacetic acid to produce carboxylated graphene oxide (GO-COOH). The successful synthesis of graphene oxide and its modification has been confirmed using Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray Diffraction (XRD), Scanning electron microscopy (SEM), Energy Dispersive X-ray Analysis (EDX) and Transmission electron microscopy (TEM). The increase in surface area of graphene oxide after treatment with chloroacetic acid characterized by BET indicated its successful modification. A batch experiment was conducted to optimize the different factors affecting adsorption of both heavy metals on GO-COOH. After functionalization, we achieved maximum adsorption capacities of 588.23 mg g^-1 and 370.37 mg g^-1 for Pb and Cr, respectively, by GO-COOH which were high compared to the previously reported adsorbents of this kind. The Langmuir model (R² = 0.998) and Pseudo-second-order kinetic model (R² = 0.999) confirmed the monolayer adsorption of Pb and Cr on GO-COOH and the chemisorption as the dominant process governing adsorption mechanism. The present work shows that the carboxylation of GO can enhance its adsorption capacity efficiently and may be applicable for the treatment of wastewater.

Prospects of titanium carbide-based MXene in heavy metal ion and radionuclide adsorption for wastewater remediation: A review

Contamination of water sources with various organic and inorganic non-biodegradable pollutants is becoming a growing concern due to industrialization, urbanization, and the inefficiency of traditional wastewater treatment processes. Transition Metal Carbides/Nitrides (MXenes) are emerging as advanced nanomaterials of choice for treating contaminated water owing to their excellent conductivity, mechanical flexibility, high specific surface area, scalable production, rich surface functionalities, and layered morphology. MXenes have demonstrated enhanced ability to adsorb various organic and inorganic contaminants depending upon their surface terminal groups (-OH, -F, and -O) and interlayer spacing. Titanium carbide (Ti₃C₂T_x) is most researched to date due to its ease of processing and stability. Ti₃C₂T_x has shown excellent performance in absorbing heavy metal ions and radioactive heavy metals. This review summarizes state-of-the-art Ti₃C₂T_x synthesis, including selective etching techniques, optimization of the desired adsorption features (controlling surface functional groups, intercalation, sonication, and functionalization), and regeneration and adsorption mechanism to remove contaminants. Furthermore, the review also compares the adsorption performance of Ti₃C₂T_x with other commercial adsorbents (including chitosan, cellulose, biomass, and zeolites). Ti₃C₂T_x has been found to have an adsorption efficiency of more than 90% in most studies due to its layered structure, which makes the functional groups easily accessible, unique and novel compared to other conventional nanomaterials and adsorbents. The challenges, potential solutions, and prospects associated with the commercial development of Ti₃C₂T_x as adsorbents are also discussed. The review establishes a framework for future wastewater treatment research using MXenes to address the global problem of water scarcity.

Synthesis and application of graphene oxide as a nanoadsorbent to remove Cd (II) and Pb (II) from water: adsorption equilibrium, kinetics, and regeneration

In this work, graphene oxide (GO) was synthesized by the modified Hummers method. The nanomaterial was characterized by FTIR and Raman spectroscopy, SEM, and pH at the point of zero charge. GO exhibited typical characteristics of graphene-based materials, indicating that graphite oxidation and exfoliation occurred successfully. Cd (II) and Pb (II) adsorption onto GO was carried out in batch systems, in which the effect of adsorbent dosage, contact time, and initial adsorbate concentration were evaluated. Langmuir, Freundlich, and Sips isotherm models, as well as pseudo order models and Elovich kinetic equation were applied to adsorption experimental data. Results indicated that increasing adsorbent mass, the removal efficiency of Cd (II) and Pb (II) increased. Freundlich isotherm better described Pb (II) adsorption (R² = 0.96), while Cd (II) isotherm showed linear behavior. From the Akaike's AIC parameter, kinetic data were satisfactorily described by pseudo-first order (Cd (II)) and pseudo-n order (Pb (II)) models. GO was successfully subjected to five regeneration cycles, maintaining high efficiency (> 90%) in all cycles. GO showed high potential for the adsorption of Cd (II) and Pb (II) from aqueous solution, due to its high adsorption capacity, rapid Cd (II) and Pb (II) intakes, and great regeneration performance.

Highly efficient recovery of heavy rare earth elements by using an amino-functionalized magnetic graphene oxide with acid and base resistance

In the application of various magnetic materials for water treatment, control of surface resistance to acid and alkali corrosion remains largely overlooked, which could greatly extend their service life. We herein prepare amino grafted magnetic graphene oxide composites using a simple one-step cross-link reaction between the graphene oxide and magnetic Fe₃O₄/C nanoparticles. The as-prepared magnetic graphene oxide composites have long-term stability under acid and alkali solutions and shows an excellent performance in removing Ho(III), a representative rare earth element (REE) from water. The observed adsorption capacity of 72.1 mg Ho(III)/g exceeded that of most magnetic materials previously reported. Regeneration of the magnetic composites was realized in acid and alkali solutions but their structural integrity and physicochemical properties retained even after 18 adsorption-desorption cycles. The current adsorbent also shows excellent adsorption performance for other heavy REEs, such as Er(III), Eu(III), Lu(III), Tm(III), Y(III) and Yb(III). This work can provide a new strategy for constructing an acid and base resistance magnetic graphene oxide for the high-efficient recovery of heavy REEs from aqueous solution.

Facile fabrication of N-doped hierarchical porous carbons derived from soft-templated ZIF-8 for enhanced adsorptive removal of tetracycline hydrochloride from water

N-doped hierarchical porous carbons (NHPCs) were successfully prepared from soft-templated zeolitic imidazolate framework-8 (ZIF-8) precursors using sodium dodecylbenzene sulfonate (SDBS) as a template through facile one-step carbonization and applied in tetracycline hydrochloride (TCH) adsorption. The NHPC synthesized at 1000 °C with an SDBS/Zn²⁺ molar ratio of 0.075 exhibited the highest TCH adsorption (q_m = 80.92 mg g^-1) owing to its relatively large BET surface area (1067.41 m² g^-1) and pore volume (1.22 cm³ g^-1) and the stronger surface interaction between TCH and NHPCs (HC1000-0.075). Compared with surfactant-free ZIF-8-derived carbon (HC), introduction of SDBS in the ZIF-8 precursor not only improved the pore structure of the carbon materials but also increased the nitrogen content and the number of surface functional groups. Adsorption kinetics and isotherms showed that the pseudo-second-order model and Sips model fit the TCH adsorption behavior on HC and HC1000-0.075 well. Adsorption experiments and characterizations revealed that the adsorption mechanism involved in TCH adsorption on HC1000-0.075 mainly depended on the synergistic effect of pore filling, H-bonding, π-π interactions, and weak electrostatic interactions. This study provides an effective and simple strategy for fabricating MOF-derived NHPCs as a promising adsorbent for the removal of antibiotics from water.

Enhanced adsorption of perfluorooctanoate (PFOA) onto low oxygen content ordered mesoporous carbon (OMC): Adsorption behaviors and mechanisms

The pollution of perfluorooctanoic acid (PFOA) in water bodies has been a serious threat to environment and human health. Ordered mesoporous carbons (OMCs) with different oxygen contents were prepared and first used for adsorbing PFOA from aqueous solutions. The OMC-900 with a lower oxygen content has a higher PFOA adsorption capacity than the oxygen-rich OMC-700. OMCs require a much shorter time to reach the adsorption equilibrium comparing with other adsorbents reported in literature. The mesopores play an important role in this rapid adsorption kinetics. The pseudo-second-order model better fitted the kinetic data. The multilayers adsorption was proposed for the adsorption of PFOA onto OMCs since the Freundlich isotherm model fits the experimental data well. The micelle or hemi-micelle structures may be formed during the adsorption. Various background salts showed a positive effect on PFOA adsorption due to the salting-out and divalent bridge effects. The humic acid can lead to a discernible reduction in PFOA adsorption by competing for adsorption sites on OMCs. The hydrophobic interaction and electrostatic interaction adsorption mechanisms were proposed and verified by the adsorption data. The high adsorption capacity and fast adsorption kinetics of the OMC make it a potential adsorbent for PFOA removal in engineering applications.

Phosphate-crosslinked β-cyclodextrin polymer for highly efficient removal of Pb(ii) from acidic wastewater

Novel phosphate-crosslinked β-cyclodextrin polymer was synthesized for highly efficient Pb(ii) removal from acidic wastewater.

Recyclable nitrogen-doped biochar via low-temperature pyrolysis for enhanced lead(II) removal

Facile and low-cost preparation are essential in the conversation of agricultural waste into biochar. In this work, nitrogen-doped biochar (NBC-350-0.1) was prepared by thermal decomposition of urea (urea/biochar = 0.1:1 mass ratio) at a low temperature of 350 °C. NBC-350-0.1 showed good performance for Pb(II) removal with the maximum adsorption capacity of 130.87 mg g^-1 at 25 °C, which was five times that of pristine biochar (BC). Adsorption kinetics, isotherms and thermodynamics studies indicated that the adsorption of Pb(II) by NBC-350-0.1 or BC was the homogeneous monolayer adsorption with chemical action as the rate-limiting step, and was accompanied by spontaneous endothermic. Further analysis showed that the removal of Pb(II) on NBC-350-0.1 and BC depended on the complexation with unsaturated carbon bonds and ion exchange with Ca(II). Moreover, graphitic- and pyridinic-N in NBC-350-0.1 exerted a key part in the adsorption of Pb(II). NBC-350-0.1 regenerated by NaOH exhibited excellent recycling performance keeping the original removal efficiency at 84% after five cycles. In addition, this N doping method is suitable for improving the performance of coffee grounds, sawdust, and bagasse biochar. These results would provide an idea for obtaining recyclable N-doped biochar to treat the Pb(II) polluted wastewater.

Enhanced adsorption of resorcinol onto phosphate functionalized graphene oxide synthesized via Arbuzov Reaction: A proposed mechanism of hydrogen bonding and π-π interactions

Phosphate functionalized graphene oxide (PGO) was successfully prepared by Arbuzov reaction and employed for adsorption of resorcinol from an aqueous phase. The phosphate functional groups were successfully incorporated onto the PGO surface by the formation of P-C bonds as identified by the analysis of FTIR and XPS spectra. The evaluation of adsorption capacity of resorcinol onto PGO exhibited significant improvement of resorcinol removal, achieving an adsorption capacity of 50.25 mg/g in the pH range of 4-7 which was 15 times higher than pristine graphene oxide. The addition of 2.4 M and 5 M NaCl in the adsorption system significantly increased the adsorption capacity towards resorcinol from 50.25 mg/g to 82.10 mg/g and 128.10 mg/g, respectively. Based on kinetics and adsorption isotherm studies, Pseudo-First-Order and Langmuir model are the best model to describe the adsorption process indicating that the adsorption is dominantly controlled by physisorption. The thermodynamic analysis suggested that the adsorption process was the favorable, spontaneous, and endothermic process. Besides, the interplay of hydrogen bonding and π-π interactions is proposed to be the governing physisorption mechanism. The outstanding reusability and better adsorption performance make PGO a promising adsorbent for environmental remediation of resorcinol.

Phenylthiosemicarbazide-functionalized UiO-66-NH2 as highly efficient adsorbent for the selective removal of lead from aqueous solutions

A novel metal-organic framework (UiO-66-PTC) for efficient removal of Pb²⁺ ions from wastewater has been prepared by using 4-phenyl-3-thiosemicarbazide as the modifier. Various characterizations showed that UiO-66-PTC was successfully synthesized. The absorption results showed that the maximum adsorption capacity of Pb(II) is 200.17 mg/g at 303 K and optimal pH 5. The adsorption kinetic follows the pseudo-second-order model and the adsorption isotherms fit the Langmuir model. This shows that Pb(II) is a single-layer adsorption on the surface of the adsorbent and the rate-controlling step is chemical adsorption. The thermodynamic results show that the adsorption process can proceed spontaneously, belong to the exothermic reaction. The adsorbent can selectively uptake lead ions from wastewater containing multiple interfering ions. After four adsorption and desorption cycles, the adsorption efficiency is still high. The adsorption mechanism of Pb(II) on the adsorbent is mainly through the chelation of Pb(II) with N and S atoms. These results indicate that UiO-66-PTC is an effective material for efficiently and selectivity removal of Pb(II) from solution, which is of practical significance.

Surfactant-assisted adsorption of uranyl ions in aqueous solution on TiO2/polythiophene nanocomposite

In this work, hexadecyltrimethylammonium-bromide (HTAB)-modified polythiophene (PTh)/TiO₂ nanocomposite (HTAB/PTh/TiO₂) was applied to remove uranyl ions (UO₂²⁺). FT-IR, XRD, ζ potential, TGA, SEM, and XPS were utilized to obtain the chemical and physical properties of HTAB/PTh/TiO₂. The effects of HTAB content, preparation temperature, and adsorption conditions on UO₂²⁺ removal were investigated comprehensively. And the UO₂²⁺ adsorption process on HTAB/PTh/TiO₂ was fitted to the Sips model with a saturated adsorption capacity of 234.74 mg/g, which was 6 times over TiO₂. The results suggested that the surfactant of HTAB can significantly improve the adsorption ability of TiO₂ for UO₂²⁺ ions. This work provides a strategy of surfactant modification for enhancing the separation and recovery ability of adsorbent toward UO₂²⁺ in the radioactive wastewater.

Novel recycling of incinerated sewage sludge ash (ISSA) and waste bentonite as ceramsite for Pb-containing wastewater treatment: Performance and mechanism

With rapid economic growth and urbanisation, the reuse and recycling of solid wastes has become a high priority for the sustainable development of modern cities. In this study, two typical solid wastes, incinerated sewage sludge ash (ISSA) and waste bentonite, were co-valorised to produce granular adsorbents through a simple and energy-saving pelletisation/sintering process. A mixture of ISSA and bentonite at a weight ratio of 3:1 was pelletised and sintered at 700 °C. The resultant ceramsite, with good mechanical strength, could effectively remove Pb(Ⅱ) from aqueous solutions. The adsorption kinetics can be described by the pseudo-first-order (PFO) model. The results indicated that the Pb(Ⅱ) adsorption process was dominated by electrostatic attraction, precipitation, and complexation. The isothermal data exhibited a good correlation with the Freundlich model, indicating that the adsorption process was non-ideal and spontaneous. The maximum adsorption capacity was approximately 21.6 ± 0.35 mg/g at 318 K. After 5 cycles of regeneration, the adsorbent maintained good adsorption performance. Moreover, the removal rate was not greatly affected by ionic strength. These findings demonstrate that the granular adsorbent prepared with ISSA and waste bentonite can be recognised as a promising adsorbent for Pb-containing wastewater treatment.

A novel dispersive magnetic solid phase microextraction using ionic liquid-coated amino silanized magnetic graphene oxide nanocomposite for high efficient separation/preconcentration of toxic ions from shellfish samples

A novel dispersive magnetic solid phase microextraction (d-MSPE) method using ionic liquid-coated amino silanized magnetic graphene oxide (MGO@SiO₂-APTES-IL) as adsorbent has been established for enriching and extracting lead(II), copper(II) and cadmium(II) in shellfish samples. The novel nanocomposite was proved synthesized successfully by various characterization technologies. Parameters that could affect the recoveries of target ions were investigated and optimized focusing on adsorption and desorption using Box-Behnken design of response surface methodology (BBD-RSM). The limits of detection (LODs) for three target heavy metal ions were 2.42, 3.36, 3.75 ng L^-1, respectively. Additionally, the maximum adsorption capacities of the nanocomposite for target ions were 251.23, 138.51, 159.31 mg g^-1 at 298 K, respectively, the nanoadsorbent can be regenerated without significant adsorption capacities loss for four times. These observations revealed that the novel nanocomposite can be used as an excellent adsorbent for separation and preconcentration of the target ions.

One-step synthesis of cake-like biosorbents from plant biomass for the effective removal and recovery heavy metals: Effect of plant species and roles of xanthation

The continuous production of plant wastes and heavy metal pollution of waters have become widespread unavoidable challenges. Reutilization of plant wastes to treat toxic metal-contaminated water is an eco-friendly way to simultaneously solve these problems. Herein, three cake-like biosorbents were synthesized from tea waste, trimmed lawn grass and Nephrolepis cordifolia leaves through a one-step xanthation modification method combined with lyophilization, respectively. The plant species affected the appearance, structure and mechanical strength of the biosorbents due to the different contents of hydrocarbons and inorganic substances, which influenced the gel-like degree and thus the ability of the particles to pack between water molecules. The maximum adsorption capacities of the modified materials for Pb(II), Cu(II) and Cd(II) were 247.20, 85.80 and 265.31 mg/g, respectively, far higher than those of the original wastes, and the adsorption was selective. These results were mainly attributed to newly introduced -(CS)-S-Na groups, which triggered ion exchange, complexation and microprecipitation between heavy metal ions and functional groups. As-prepared biosorbents owned an excellent regenerability, which contributed to recovery heavy metals. The physicochemical properties and adsorption performances of the modified materials indicated that xanthation is a universal modification method suited to different plant biomasses with great potential to purify heavy metal-contaminated water. These biosorbents with excellent separability and regenerability might be promising for continuous-flow sewage treatment.

A Review on Heavy Metal Ions and Containing Dyes Removal Through Graphene Oxide-Based Adsorption Strategies for Textile Wastewater Treatment

Textile wastewater heavy metal pollution has become a severe environmental problem worldwide. Metal ion inclusion in a dye molecule exhibits a bathochromic shift producing deeper but duller shades, which provides excellent colouration. The ejection of a massive volume of wastewater containing heavy metal ions such as Cr (VI), Pb (II), Cd (II) and Zn (II) and metal-containing dyes are an unavoidable consequence because the textile industry consumes large quantities of water and all these chemicals cannot be combined entirely with fibres during the dyeing process. These high concentrations of chemicals in effluents interfere with the natural water resources, cause severe toxicological implications on the environment with a dramatic impact on human health. This article reviewed the various metal-containing dye types and their heavy metal ions pollution from entryway to the wastewater, which then briefly explored the effects on human health and the environment. Graphene-based absorbers, specially graphene oxide (GO) benefits from an ordered structured, high specific surface area, and flexible surface functionalization options, which are indispensable to realize a high performance of heavy metal ion removal. These exceptional adsorption properties of graphene-based materials support a position of ubiquity in our everyday lives. The collective representation of the textile wastewater's effective remediation methods is discussed and focused on the GO-based adsorption methods. Understanding the critical impact regarding the GO-based materials established adsorption portfolio for heavy metal ions removal are also discussed. Various heavy-metal ions and their pollutant effect, ways to remove such heavy metal ions and role of graphene-based adsorbent including their demand, perspective, limitation, and relative scopes are discussed elaborately in the review.

Oxide modified aluminum for removal of methyl orange and methyl blue in aqueous solution

Oxide modified Al exhibited a higher efficiency in removing organic dyes in aqueous solution than pristine Al.

Goethite dispersed corn straw-derived biochar for phosphate recovery from synthetic urine and its potential as a slow-release fertilizer

In this study, goethiete (α-FeOOH) -biochar (BC) composites were successfully developed from a co-precipitation reaction under alkaline conditions (pH = 11.93) and used as the adsorbent for phosphate recovery from urine. The morphology and crystallinity of α-FeOOH-BC composites were characterized by scanning electron microscopy and X-ray diffraction. α-FeOOH loaded BC was found to be amorphous. This may be caused by the Si residue in BC. The Elovich model and the Langmuir model fit better to the kinetic and isotherm results of α-FeOOH-600BC, respectively, indicating that phosphate adsorption is mainly a chemisorption and monolayer adsorption process. The α-FeOOH-600BC with amorphous structure showed higher adsorption capacity than crystalline α-FeOOH, and the maximum phosphate sorption capacity reached 57.39 mg g^-1. Additionally, the extractable phosphate of this material was approximately 967.5 mg P·kg^-1 suggesting the α-FeOOH-600BC after adsorption could be a promising alternative as a slow-phosphate-release fertilizer. Fourier-transform infrared and X-ray induced photoelectron spectroscopy results showed that the active sites of the adsorption of phosphate were the Fe-OH bonds that formed inner-sphere complexes (Fe-O-P).

Enhanced adsorption of Pb(II) by nitrogen and phosphorus co-doped biochar derived from Camellia oleifera shells

We describe the synthesis of a series of novel nitrogen- and phosphorus-enriched biochar (activated carbon, AC) nanocomposites via the co-pyrolysis of Camellia oleifera shells (COSs) with different weight ratios of ammonium polyphosphate (APP) (w_APP: w_COSs = 1-3:1). The physicochemical characteristics of these nanocomposites (APP@ACs) were investigated via X-ray diffraction (XRD), Raman spectroscopy, N₂ adsorption/desorption analysis, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). The results revealed that the APP@ACs exhibited richer N- and P-containing functional groups than unmodified AC. In addition, the removal performance of APP@AC-3 with respect to Pb(II) (723.6 mg g^-1) was greatly improved relative to unmodified AC (264.2 mg g^-1). Kinetic and equilibrium data followed the pseudo-second-order kinetic model and Langmuir model, respectively. The removal mechanism could be attributed to partial physisorption and predominant chemisorption. The N₂ adsorption/desorption isotherms demonstrated that pore-volume properties could be an effective physical trap for Pb(II). Furthermore, the XPS and FTIR analysis revealed that the chemical removal mechanism of the APP@ACs is surface complexation via N-containing and P-containing functional groups. These findings indicate that the co-pyrolysis of COSs and APP leads to the formation of nitrogen- and phosphorus-containing functional groups that facilitate excellent activated carbon-based (biochar) adsorption performance.

Efficient removal of Pb(II) through recycled biochar-mineral composite from the coagulation sludge of swine wastewater

Zeolite-Mg/Fe chloride dual enhanced coagulation is a cost-effective method for advanced treatment of swine wastewater, but the sludge generated after the enhanced coagulation remains to be a problem. In this study, the precipitate from a swine wastewater coagulation unit was regenerated by pyrolysis treatment in an O₂-limited environment to develop a high efficient adsorbent (biochar-mineral composite, BMC) for the removal of Pb(II) from wastewater. SEM images indicate that complex Mg/Fe oxides and sludge biochar gathered around zeolite particles. Effects of different influencing factors such as Pb(II) initial concentration, pH, adsorption time and ion concentration on the adsorption performance were investigated. The results show that the Langmuir isotherm model can better express the adsorption of Pb(II) on BMC than Freundlich model and Temkin model. BMC pyrolyzed at 500 °C showed the maximum adsorption capacity of 450.58 mg/g under experimental condition of 25 °C, 100 mg/L Pb(II) initial concentration and the initial pH of 5.6. The adsorption mechanisms on BMC mainly include ion exchange, electrostatic interaction. Therefore, it is a cost-effective and environmental-friendly strategy to obtain biochar-mineral composite from recycled sludge, which can efficiently remove Pb(II) from wastewater.

The use of artificial neural network (ANN) for modeling adsorption of sunset yellow onto neodymium modified ordered mesoporous carbon

Discharging coloring products in water bodies has degraded water quality irreversibly over the past several decades. Order mesoporous carbon (OMC) was modified by embedding neodymium(III) chloride on the surface of OMC to enhance the adsorptive removal towards these contaminants. This paper represents an artificial neural network (ANN) based approach for modeling the adsorption process of sunset yellow onto neodymium modified OMC (OMC-Nd) in batch adsorption experiments. Neodymium modified OMC was characterized using N₂ adsorption-desorption isotherm, TEM micrographs, FT-IR and XPS spectra analysis techniques. 2.5 wt% Nd loaded OMC was selected as the final adsorbent for further experiments because OMC-2.5Nd showed highest removal efficiency of 93%. The ANN model was trained and validated with the adsorption experiments data where initial concentration, reaction time, and adsorbent dosage were selected as the variables for the batch study, whereas the removal efficiency was considered as the output. The ANN model was first developed using a three-layer back propagation network with the optimum structure of 3-6-1. The model employed tangent sigmoid transfer function as input in the hidden layer whereas a linear transfer function was used in the output layer. The comparison between modeled data and experimental data provided high degree of correlation (R² = 0.9832) which indicated the applicability of ANN model for describing the adsorption process with reasonable accuracy.

Enhanced Pb(II) adsorption onto functionalized ordered mesoporous carbon (OMC) from aqueous solutions: the important role of surface property and adsorption mechanism

Functionalized ordered mesoporous carbon (MOMC-NP) was synthesized by chemical modification using HNO₃ and H₃PO₄ to enhance Pb(II) adsorption. The phosphate functional group represented by P-O-C bonding onto the surface of OMC was verified by FT-IR and XPS. Batch adsorption experiments revealed the improvement of adsorption capacity by 39 times over the virgin OMC. Moreover, the Pb(II) adsorption results provided excellent fits to Langmuir model and pseudo-second-order kinetic model. The adsorption mechanism of Pb(II) onto MOMC-NP revealed the formation of metal complexes with carboxyl, hydroxyl, and phosphate groups through ion exchange reactions and hydrogen bondings. The calculated activation energy was 22.09 kJ/mol, suggesting that Pb(II) adsorption was a chemisorption. At pH>pH_pzc, the main Pb(II) existing species of Pb(II) and Pb(OH)⁺ combine with the carboxyl, hydroxyl, and phosphate functional groups via electrostatic interactions and hydrogen bonding. All these findings demonstrated that MOMC-NP could be a useful and potential adsorbent for adsorptive removal of Pb(II). Graphical abstract.

Organic Functionalized Graphene Oxide Behavior in Water

Surface modified graphene oxide (GO) has received broad interest as a potential platform material for sensors, membranes, and sorbents, among other environmental applications. However, compared to parent (unmodified) GO, there is a dearth of information regarding the behavior of subsequently (secondary) modified GO, other than bulk natural organic matter (NOM) coating(s). Here, we systematically explore the critical role of organic functionalization with respect to GO stability in water. Specifically, we synthesized a matrix of GO-based materials considering a carefully chosen range of bound organic molecules (hydrophobic coatings: propylamine, tert-octylamine, and 1-adamantylamine; hydrophilic coatings: 3-amino-1-propanol and 3-amino-1-adamantanol), so that chemical structures and functional groups could be directly compared. GO (without organic functionalization) with varying oxidation extent(s) was also included for comparison. The material matrix was evaluated for aqueous stability by comparing critical coagulation concentration (CCC) as a function of varied ionic strength and type (NaCl, CaCl₂, MgCl₂, and MgSO₄) at pH 7.0. Without surface derivatization (i.e., pristine GO), increased stability was observed with an increase in the GO oxidation state, which is supported by plate–plate Derjaguin, Landau, Verwey and Overbeek (DLVO) energy interaction analyses. For derivatized GO, we observed that hydrophilic additions (phi-GO) are relatively more stable than hydrophobic organic coated GO (pho-GO). We further explored this by altering a single OH group in the adamantane-x structure (3-amino-1-adamantanol vs. 1-adamantylamine). As expected, Ca²⁺ and monovalent co-ions play an important role in the aggregation of highly oxidized GO (HGO) and phi-GO, while the effects of divalent cations and co-ions were less significant for pho-GO. Taken together, this work provides new insight into the intricate dynamics of GO-based material stability in water as it relates to surface functionalization (surface energies) and ionic conditions including type of co- and counter-ion, valence, and concentration.

Rational structural design of ZnOHF nanotube-assembled microsphere adsorbents for high-efficient Pb2+ removal

Hierarchical nanotube-assembled ZnOHF microspheres were prepared via an amino acid assisted hydrothermal method, which can remove Pb²⁺ efficiently in an aqueous environment.