Distribution behavior of arsenate into α-calcium sulfate hemihydrate transformed from gypsum in solution

Mineralogical transformation of arsenic at different copper smelting workshops: The impact on arsenic bioaccessibility

Soil arsenic (As) contamination associated with the demolition of smelting plants has received increasing attention. Soil As can source from different industrial processes, and also participate in soil weathering, making its speciation rather complex. This study combined the usage of chemical sequential extraction and advanced spectroscopic techniques, e.g., time of flight secondary ion mass spectrometry (ToF-SIMS), to investigate the mineralogical transformation of soil As at different processing sites from a typical copper smelting plant in China. Results showed that the stability of arsenic species decreased following the processes of storage, smelting, and flue gas treatment. Arsenic in the warehouse area was incorporated into pyrite (FeS2) as well as its secondary minerals such as jarosite (KFe3(SO4)2(OH)6). At the smelting area, a large proportion of As was adsorbed by iron oxides from smelting slags, while some As existed in stable forms like orpiment (As2S3). At the acid-making area, more than half of As was adsorbed on amorphous iron oxides, and some were adsorbed on the flue gas desulfurization gypsum. More importantly, over 86% of the As belonged to non-specifically and specifically adsorbed fractions was found to be bioaccessible, highlighting the gypsum-adsorbed As one of the most hazardous species in smelting plant soils. Our findings indicated the importance of iron oxides in As retention and suggested the potential health risk of gypsum-adsorbed As. Such detailed knowledge of As speciation and bioaccessibility is vital for the management and remediation of As-contaminated soils in smelting plants.

Synthesis of magnetic adsorbents from titanium gypsum and biomass wastes for enhanced phosphate removal

A novel scheme was proposed to prepare magnetic adsorbents by co-pyrolysis of titanium gypsum (TiG) and agricultural biomass wastes for phosphate (P) recovery. Co-presence of biomass wastes could improve TiG decomposition in inert atmosphere to generate magnetic centers and active sites, and P adsorption correlated well with organic volatiles of biomass wastes. The adsorption process evolved from a biomass-controlled process to a TiG-controlled process when increasing the mass ratio of corncob above 10 %. The optimal adsorbent (i.e. GC₁₀) exhibited higher P adsorption capacity (Q_m 183 mg/g) than many previous adsorbents; moreover, it can be magnetically separated from water after P adsorption. Active sites including CaO, CaS and Fe₃O₄ were deemed as the main factors for P chemisorption and surface precipitation. Most of adsorbed P could be released continuously and slowly by dilute NaHCO₃. These results highlight potential applications of TiG and biomass waste derived adsorbents in P purification and recovery.

Efficient remediation of heavily As(III)-contaminated soil using a pre-oxidation and stabilization/solidification technique

The high mobility of As(III) makes it difficult to remediate heavily As(III)-contaminated soil. A novel remediation technique that combines pre-oxidation and stabilization/solidification (PO + S/S) is proposed in this study to remediate heavily As(III)-contaminated soil. After oxidizing As(III) in the contaminated soil using Fenton's reagent, FeCl₃·6H₂O was used as a chemical stabilizing agent to reduce the toxicity and mobility of As. Finally, Portland cement (PC) was used for solidification. The effects and mechanisms of the proposed technique were studied using unconfined compressive strength tests, leaching tests, sequential extraction procedure (SEP), and a series of spectroscopic/microscopic investigations. The experimental results showed that the addition of FeCl₃·6H₂O increased the strength of the curing body because the hydration degree of PC and pore structure were improved. Portland cement can increase the pH of the curing body. At a 1:1 Fe to As molar ratio and a 15 wt% PC dosage, the leached As concentration decreased to 3.25 mg L^-1, and the remediation efficiency reached 99.54%. The SEP results showed that the PO + S/S treatment converted As into more stable phases and effectively reduced the potential mobile phase risk. The majority of As was bound to hydrated iron oxides; however, the increased pH affected the Fe-As interactions and prompted the release of As from the surface of the hydrated iron oxides. Spectroscopic/microscopic investigations indicated that the PO + S/S treatment converted As(III) to less toxic and less mobile As(V) and then immobilized by the encapsulation of calcium silicate hydrate and ion exchange of ettringite. This study provides a scientific basis and theoretical support for the effective remediation of heavily As(III)-contaminated soil.

A Simple and Efficient Method for Preparing High-Purity α-CaSO4·0.5H2O Whiskers with Phosphogypsum

A simple and efficient approach for the high-purity CaSO₄·2H₂O (DH) whiskers and α-CaSO₄·0.5H₂O (α-HH) whiskers derived from such phosphogypsum (PG) was proposed. The impact of different experimental parameters on supersaturated dissolution–recrystallization and preparation processes of α-CaSO₄·0.5H₂O was elaborated. At 3.5 mol/L HCl concentration, the dissolution temperature and time were 90 °C and 20 min, respectively. After eight cycles and 5–8 times cycles, total crystallization amount of CaSO₄·2H₂O was 21.75 and 9.97 g/100 mL, respectively, from supersaturated HCl solution. The number of cycles affected the shape and amount of the crystal. Higher HCl concentration facilitated CaSO₄·2H₂O dissolution and created a much higher supersaturation, which acted as a larger driving force for phase transformation of CaSO₄·2H₂O to α-CaSO₄·0.5H₂O. The HCl solution system’s optimum experimental conditions for HH whiskers preparation involved acid leaching of CaSO₄·2H₂O sample, with HCl concentration 6.0 mol/L, reaction temperature 80 °C, and reaction time 30 min–60 min. Under the third cycle conditions, α-CaSO₄·0.5H₂O whiskers were uniform in size, clear, and distinct in edges and angles. The length range of α-CaSO₄·0.5H₂O whiskers was from 106 μm to 231 μm and diameter range from 0.43 μm to 1.35 μm, while the longest diameter ratio was 231. Purity of α-CaSO₄·0.5H₂O whiskers was approximately 100%, where whiteness reached 98.6%. The reuse of the solution enables the process to discharge no waste liquid. It provides a new reference direction for green production technology of phosphogypsum.

Production and resource utilization of flue gas desulfurized gypsum in China - A review

Flue gas desulfurized gypsum (FGD gypsum), mainly originates from thermal power plants, smelters, and large-scale enterprise boilers. This article reviews the production in China and the latest beneficial utilizations of FGD gypsum. China is a large coal-consuming country and has always had serious SO₂ emissions. Therefore, the Chinese government has implemented a large number of desulfurization measures since 2006. With continually increasing energy consumption and increasingly stringent environmental requirements, the production of FGD gypsum has exceeded 10⁸ tons. The basic properties and the current beneficial applications of FGD gypsum are summarized here. The practical application of FGD gypsum in four fields-building materials, agriculture, material synthesis, and soil-and its impact on the environment, are analyzed. Finally, a new direction is proposed for the future utilization of FGD gypsum.