Flower-like Bi2S3-In2S3 heterojunction for efficient solar light induced photoreduction of Cr(VI)

Solar-based technologies for removing potentially toxic metals from water sources: a review

Technological advances have led to a proportional increase in the deposition of contaminants across various environmental compartments, including water sources. Heavy metals, also known as potentially toxic metals, are of particular concern due to their significant harmful impacts on environmental and human health. Among the available methods for mitigating the threat of these metals in water, solar radiation-based technologies stand out for their cleanliness, cost-effectiveness, and efficiency in removing or reducing the toxicity of heavy metals. The performance and productivity of these methods in removing heavy metals such as arsenic (As), chromium (Cr), mercury (Hg), and uranium (U) from water still need to be comprehensively synthesized. Thus, this work aims to address that gap. The performance, potential, and challenges of real-world applications of conventional solar stills (CSS), membrane-based solar stills, and solar heterogeneous photocatalysis are concisely summarized and critically reviewed. CSS and membrane-based stills are highly effective (efficacy > 98%) in removing and capturing heavy metals from water. However, structural and functional improvements are needed to enhance productivity (especially for CSS) and usability in real-world environmental remediation and drinking water supply scenarios. Solar heterogeneous photocatalysis is highly effective in removing and/or converting As, Cr, Hg, and U into their non-toxic or less toxic forms, which subsequent processes can easily remove. Further research is necessary to evaluate the safety of photocatalytic materials, their integration into scalable solar reactors, and their usability in real-world environmental remediation applications.

Controllable fabrication of SbxBi2-xS3 solid solution photocatalysts with superior elimination for Cr(VI)

The development of environmentally friendly and cost-effective photocatalysts is of vital significance for the effective removal of heavy metal contamination in water, but it is still a crucial challenge. Herein, the novel SbxBi2-xS3 solid solution photocatalysts with a certain amount of sulfur vacancy were prepared by adjusting the molar ratio of Sb to Bi through a simple hydrothermal strategy, and was applied to the effective photocatalytic reduction of hexavalent chromium (Cr(VI)). Sb1.75Bi0.25S3 with optimized ratio has superior reduction performance of Cr(VI), and the photocatalytic efficiency of Cr(VI) can achieve 91.9 % within 1 h of visible light illumination. The remarkable catalytic efficiency is due to the more applicable band structure of the solid solution photocatalyst, which is conducive for the photocatalytic reaction. Moreover, the substitution of Bi causes the crystal distortion of Sb2S3 and induce the generation of sulfur defects, which can effectively capture photoelectrons, accelerate the carriers separation, and improve the reduction performance. This study provides a hopeful photocatalyst for wastewater purification and promotes the exploration of solid solution photocatalyst in water environment remediation.

An innovative Z-type Sb2S3/In2S3/TiO2 heterostructure: superior performance in the photocatalytic removal of levofloxacin and mechanistic insight

In this study, Sb2S3/In2S3/TiO2 (SIT) heterojunction photocatalysts were prepared by a simple two-step hydrothermal method and applied to the photocatalytic degradation of levofloxacin (LEV). After 160 min of reaction under visible light, the SIT heterojunction photocatalyst degraded 10 mg L-1 LEV at a rate of 86.7%. The degradation of LEV follows pseudo-first-order kinetics with a rate constant 1.16 × 10-2 min-1, which is 1.42, 1.22 and 1.05 times higher than that of TiO2, SI and IT, respectively. Meanwhile, the SIT photocatalysts also showed high photocatalytic activity for other antibiotics. The enhanced photocatalytic activity of the ternary heterostructures was attributed to the full-spectrum response and the synergistic effect of the dual Z-type heterojunctions, which improved the visible light absorption and facilitated the charge separation. In addition, ˙OH and ˙O2- play a dominant role in the photodegradation process. This work contributes to the design of novel photocatalytic materials with dual Z-type heterojunctions and efficient photocatalysts for the degradation of antibiotics.

The "dual-layer sulfur cathode" strategy: An In2S3/Bi2S3@rGO heterostructure as an interlayer/modified separator for boosting the areal capacities of lithium-sulfur batteries

The specific energies and energy densities of lithium-sulfur (Li-S) batteries are influenced by various cell parameters, including the sulfur loading, the sulfur weight percentage in the cathode, and the electrolyte/sulfur ratio. An In2S3/Bi2S3@rGO heterostructure was obtained by growing indium sulfide nanoparticles on the surface of bismuth sulfide nanoflowers in a graphene oxide (GO) solution via a one-step solvothermal approach. This structure was introduced as a modified separator/dual-layer sulfur cathode for Li-S batteries. The Bi2S3/In2S3 heterointerfaces act as active sites to speed up interfacial electron transfer, along with the entrapment, diffusion, and transformation of lithium polysulfides. A Li-S cell containing a dual-layer sulfur cathode (thin layer of In2S3/Bi2S3@rGO sandwiched between two thick layers of sulfur) and coupled with an In2S3/Bi2S3@rGO-coated separator suppressed the polysulfide shuttle effect. The cell based on the dual-layer sulfur cathode technology and operated at a current rate of 0.3C achieved a high capacity (7.1 mAh cm-2) after the 200th cycle, giving an electrolyte/sulfur ratio (10 µL mg-1) under a high sulfur loading (11.53 mg cm-2). These results demonstrate the unique nature of the dual-layer sulfur cathode technique, which can yield high energy density Li-S batteries with high sulfur loadings and low electrolyte/sulfur ratios.

Fabrication of Z-scheme Bi7O9I3/g-C3N4 heterojunction modified by carbon quantum dots for synchronous photocatalytic removal of Cr (Ⅵ) and organic pollutants

Chromium(VI) (Cr(VI)), a highly toxic metal ion, generally co-exists with organic pollutants in industrial effluents. The clean and effective technology for water purification is an imperative issue but still a challenging task. A series of Bi₇O₉I₃/g-C₃N₄ (BOI/CN) composites modified by lignin-derived carbon quantum dots (CQDs) were fabricated by hydrothermal method and applied for synchronous photocatalytic removal of Cr (Ⅵ) and levofloxacin (LEV). With the modification of CQDs in BOI/CN heterojunction, the 0.5-CQD/BOI/CN photocatalyst (0.5% content of CQDs) exhibited stronger light-harvesting capacity, more efficient charge separation, and faster electron transfer. Compared to those of BOI (51.2%), CN (36.8%), and BOI/CN (74.4%), the photoreduction efficiency of Cr(VI) reached up to 100% by 0.5-CQD/BOI/CN under 60 min of light irradiation, together with 94.8% degradation efficiency of LEV. The degradation of LEV was dominantly controlled by active species (•OH and •O₂^-) identified by electron paramagnetic resonance analysis and free radical trapping experiments. The intermediates of LEV were determined by LC-MS and the possible degradation pathway was speculated in combination with density functional theory calculation, involving defluorination, decarboxylation, quinolone rings opening, and piperazine moieties oxidation reactions. This work provides an advanced strategy for the fabrication of high-efficiency CQDs-based Z-scheme photocatalysts for environmental remediation.

Vacancy-Mediated Z-Scheme Heterostructure in SnO2-Decorated Spinel In3-xS4 with Boosted Photocatalytic Activity

The widespread application of dyes and heavy metals causes increasing environmental pollution. One effective way to mitigate environmental pollution is to use semiconductor photocatalysts for redox purification of pollutants. Heterostructured photocatalysts can reduce the electron-hole recombination rate and improve light utilization. In this work, a novel SnO₂/In_3-xS₄ composite with oxygen vacancy defect-mediated Z-scheme heterostructure is constructed for the first time by a one-pot method, in which SnO₂ ultrasmall nanocrystals are decorated on nanopetals of flower-like In_3-xS₄. Material analyses show that the as-built three-dimensional hierarchical architecture is able to essentially increase the specific surface area and thus the active sites of the products. More importantly, the formation of Z-scheme heterojunction between the oxygen vacancy-induced SnO₂ defect level and the In_3-xS₄ band structure not only promotes the separation of photogenerated charges but also makes them more reactive. Through the optimization of the composition ratio between the two phases, the visible-light-driven photocatalytic reaction rates of rhodamine B degradation and Cr(VI) reduction for the developed SnO₂/In_3-xS₄ composite photocatalyst are 12.8 and 6.3 times of bare In_3-xS₄ and 32.0 and 76.0 times of bare SnO₂, respectively. This work should provide a promising implication for designing new high-performance composite photocatalysts.

Efficient Adsorption-Photocatalytic Removal of Tetracycline Hydrochloride over Octahedral MnS

To disclose the effect of crystal plane on the adsorption-photocatalytic activity of MnS, octahedral MnS was prepared via the hydrothermal route to enhance the adsorption and photocatalytic efficiencies of tetracycline hydrochloride (TCH) in visible light region. The optimal MnS treated at 433 K for 16 h could remove 94.83% TCH solution of 260 mg L-1 within 180 min, and its adsorption-photocatalytic efficiency declined to 89.68% after five cycles. Its excellent adsorption-photocatalytic activity and durability were ascribed to the sufficient vacant sites of octahedral structure for TCH adsorption and the feasible band-gap structure for visible-light response. In addition, the band gap structure (1.37 eV) of MnS with a conduction band value of -0.58 eV and a valence band value of 0.79 eV was favorable for the generation of O2-, while unsuitable for the formation of OH. Hence, octahedral MnS was a potential material for the removal of antibiotics from wastewater.

Insight into the enhanced photocatalytic activity mechanism of the Ag3VO4/CoWO4 p–n heterostructure under visible light

A novel Ag3VO4/CoWO4 p–n heterostructure was designed and prepared by an in situ growth method. The physicochemical properties were characterized by multiple techniques, and the photocatalytic performances in Cr(vi) reduction and TC degradation were also evaluated under visible-light irradiation.

Organic bromide-assisted one-pot synthesis of Bi2S3 nanorods using DMSO as a sulfur supply

Metal sulfide semiconductor nanorods have attracted much attention because of their potential use as a photo-responsive component of optical/electrical devices. In the present study, we report a simple solvothermal method...