TriMOF synergized on the surface of activated carbon produced from pineapple leaves for the environmental pollutant reduction and oxygen evolution process

Mesoporous activated carbon derived from fruit by-product by pyrolysis induced chemical activation: optimization and mechanism for fuchsin basic dye removal

In this study, pineapple crown (PC) feedstock residues were utilized as a potential precursor toward producing activated carbon (PCAC) via pyrolysis induced with ZnCl2 activation. The PCAC has a surface area (457.8 m2/g) and a mesoporous structure with an average pore diameter of 3.35 nm, according to the Brunauer-Emmett-Teller estimate. The removal of cationic dye (Fuchsin basic; FB) was used for investigating the adsorption parameters of PCAC. The optimization of significant adsorption variables (A: PCAC dose (0.02-0.1 g/100 mL); B: pH (4-10); C: time (10-90); and D: initial FB concentration (10-50 mg/L) was conducted using the Box-Behnken design (BBD). The pseudo-second-order (PSO) model characterized the dye adsorption kinetic profile, whereas the Freundlich model reflected the equilibrium adsorption profile. The maximum adsorption capacity (qmax) of PCAC for FB dye was determined to be 171.5 mg/g. Numerous factors contribute to the FB dye adsorption mechanism onto the surface of PCAC, which include electrostatic attraction, H-bonding, pore diffusion, and π-π stacking. This study illustrates the utilization of PC biomass feedstock for the fabrication of PCAC and its successful application in wastewater remediation.

High surface area activated carbon from a pineapple (ananas comosus) crown via microwave-ZnCl2 activation for crystal violet and methylene blue dye removal: adsorption optimization and mechanism

In this investigation, microwave irradiation assisted by ZnCl2 was used to transform pineapple crown (PN) waste into mesoporous activated carbon (PNAC). Complementary techniques were employed to examine the physicochemical characteristics of PNAC, including BET, FTIR, SEM-EDX, XRD, and pH at the point-of-zero-charge (pHpzc). PNAC is mesoporous adsorbent with a surface area of 1070 m2/g. The statistical optimization for the adsorption process of two model cationic dyes (methylene blue: MB and, crystal violet: CV) was conducted using the response surface methodology-Box-Behnken design (RSM-BBD). The parameters include solution pH (4-10), contact time (2-12) min, and PNAC dosage (0.02-0.1 g/100 mL). The Freundlich and Langmuir models adequately described the dye adsorption isotherm results for the MB and CV systems, whereas the pseudo-second order kinetic model accounted for the time dependent adsorption results. The maximum adsorption capacity (qmax) for PNAC with the two tested dyes are listed: 263.9 mg/g for CV and 274.8 mg/g for MB. The unique adsorption mechanism of MB and CV dyes by PNAC implicates multiple contributions to the adsorption process such as pore filling, electrostatic forces, H-bonding, and π-π interactions. This study illustrates the possibility of transforming PN into activated carbon (PNAC) with the potential to remove two cationic dyes from aqueous media.

Sonication strategy for anchoring single metal atom oxides (W, Cu, Co) on CeO2-rGO for boosting electrocatalytic oxygen evolution reaction

In the field of electrocatalysis, single-atomic-layer tungsten, copper, and cobalt oxide on CeO2, ethylene diamine (ED) and reduced graphene oxide (rGO) supported materials shows tremendous potential. Despite the enormous interest in single metal atom oxide (SMAO) catalysts, it is still very difficult to directly convert readily available bulk metal oxide into single atom oxide. It is crucial and tough to create high performance materials for the oxygen evolution reaction (OER) in an alkaline environment. Herein, a single tungsten, copper and cobalt atom oxide (SMAO) anchored on the CeO2 atomic layer and overall components deposited on the rGO (rGO-ED-CeO2-WCuCo) is prepared through a one-pot sonication technique. The presence of SMAO is identified by high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) imaging. The electrocatalytic performance of final rGO-ED-CeO2-WCuCo-30 nanocomposite for the OER in 1 M KOH electrolyte is evidenced by providing low overpotential of 283 mV at 10 mA cm-2. The Tafel slope for OER using rGO-ED-CeO2-WCuCo-30 electrocatalysts is 57.03 mV dec-1. The electrocatalytic activity of rGO-ED-CeO2-WCuCo-30 nanocomposites for OER was noticeably increased when compared to bare CeO2 nanorods (401 mV), rGO-ED-CeO2-WCo-30 (345 mV), rGO-ED-CeO2-WCu-30 (340 mV) and rGO-ED-CeO2-WCuCo-20 (321 mV) samples.

Optimization and mechanistic approach for removal of crystal violet and methylene blue dyes via activated carbon from pyrolyzed-ZnCl2 bamboo waste

In this study, bamboo waste (BW) was subjected to pyrolysis-assisted ZnCl2 activation to produce mesoporous activated carbon (BW-AC), which was then evaluated for its ability to remove cationic dyes, specifically methylene blue (MB) and crystal violet (CV), from aqueous environments. The properties of BW-AC were characterized using various techniques, including potentiometric-based point of zero charge (pHpzc), scanning electron microscopy with energy dispersive X-rays (SEM-EDX), X-ray diffraction (XRD), gas adsorption with Brunauer-Emmett-Teller (BET) analysis, infrared (IR) spectroscopy. To optimize the adsorption characteristics (BW-AC dosage, pH, and contact time) of PBW, a Box-Behnken design (BBD) was employed. The BW-AC dose of 0.05 g, solution pH of 10, and time of 8 min are identified as optimal operational conditions for achieving maximum CV (89.8%) and MB (96.3%) adsorption according to the BBD model. The dye removal kinetics for CV and MB are described by the pseudo-second-order model. The dye adsorption isotherms revealed that adsorption of CV and MB onto BW-AC follow the Freundlich model. The maximum dye adsorption capacities (qmax) of BW-AC for CV (530 mg/g) and MB (520 mg/g) are favorable, along with the thermodynamics of the adsorption process, which is characterized as endothermic and spontaneous. The adsorption mechanism of CV and MB dyes by BW-AC was attributed to multiple contributions: hydrogen bonding, electrostatic forces, π-π attraction, and pore filling. The findings of this study highlight the potential of BW-AC as an effective adsorbent in wastewater treatment applications, contributing to the overall goal of mitigating the environmental impact of cationic dyes and ensuring the quality of water resources.

Graphitic carbon-encapsulated V2O5 nanocomposites as a superb photocatalyst for crystal violet degradation

To materialize the excellent photocatalyst for crystal violet dye-degradation, the graphitic carbon-encapsulated vanadium pentoxide (GC-V₂O₅) nanocomposites were synthesized through the simple sonication method by using the green tea waste-derived GC nanoflakes and the sonochemically synthesized V₂O₅ nanorods. The nanocomposites were confirmed to comprise an aggregated morphology, in which the orthorhombic V₂O₅ nanorods were well anchored with the intertwingled GC nanoflakes. Owing to the encapsulation of defective V₂O₅ by conductive GC, the GC-V₂O₅ nanocomposites exhibited the enhanced photocatalytic dye-degradation efficiency up to 98.4% within 105 min. Namely, the encapsulated GC nanosheets might compensate the native defects (i.e., charge traps) on the V₂O₅ surface; hence, the charge transport could be enhanced during the dye-degradation process while the photocarrier recombination could be suppressed. The results suggest the conducting layer-encapsulated semiconducting oxide nanocomposites (e.g., GC-V₂O₅) to be of good use for future green environmental technology, particularly, as a superb photocatalyst for dye degradation.