Nanoparticle-embedded hydrogel synthesized electrodes for electrochemical oxidation of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS)

A neuraminidase-based electrochemical biosensor for high-throughput screening of antiviral compounds in traditional Chinese medicine

Neuraminidase (NA), a highly sensitive recognition element for anti-influenza activity, was immobilized on a glassy carbon electrode modified with nitrogen-doped graphene-functionalized multi-walled carbon nanotube composites (N-Gr/MWCNTs) and polypyrrole (Ppy) via re-polymerization. A highly sensitive electrochemical biosensor was thus developed for the rapid screening of antiviral components in natural products, utilizing the high specific surface area and conductivity of N-Gr/MWCNTs and polypyrrole, along with the high-throughput and specific recognition capabilities of NA. Under optimized conditions, the sensor was used to assess five distinct classes of compounds, demonstrating an activity sequence of Baicalein > Baicalin > Rutin ≈ Matrine > Levistilide A, which aligns with previous literature. This study presents a convenient and efficient method for screening antiviral components in natural products, providing new strategies and technological support for the development of cost-effective, eco-friendly, and rapid screening platforms.

Organic Electrochemical Transistors with Molecularly Imprinted Polymer Electrodes for Rapid Detection of Perfluorooctanoic Acid

Per- and polyfluoroalkyl substances (PFAS) are persistent environmental contaminants linked to adverse health effects, and there is a need for sensors that can detect PFAS in challenging environments. Electrochemical sensors offer significant potential for achieving cost-effective, rapid, and real-time detection of PFAS, particularly in comparison to current detection techniques, which rely on costly chromatographic methods. Here, we report that organic electrochemical transistors (OECTs) containing a molecularly imprinted polymer (MIP) gate electrode can selectively detect perfluorooctanoic acid (PFOA) in seawater. We prepared a molecularly imprinted polyaniline (PANI) gate electrode by polymerizing aniline onto filter paper in the presence of PFOA, followed by rinsing to remove the PFOA. When used as a gate electrode in an organic electrochemical device (OECT), the presence of PFOA produced a measurable change in the OECT source-drain current due to adsorption of PFOA onto the gate electrode, which reduced capacitance and increased impedance. Other molecules produced a weak or no response. Specifically, we show that the device responds strongly to PFOA but only weakly to perfluoropropionic acid (PFPrA), perfluorohexanoic acid (PFHxA), and surfactant 4-dodecylbenzenesulfonic acid (DBSA). The device is also able to selectively detect PFOA in mixtures containing these other PFAS or surfactants. We achieved a detection limit of 1.6 parts per trillion (ppt) or 3.86 × 10-12 M, below the regulatory advisory level of 70 ppt set by the United States Environmental Protection Agency for PFOA. This work demonstrates low-cost sensors capable of rapid and molecularly specific detection of PFOA, which can potentially lead to low-cost sensors for monitoring the concentrations of PFOA and other PFAS in seawater and other challenging environments.

Electrochemical destruction of PFAS at low oxidation potential enabled by CeO2 electrodes utilizing adsorption and activation strategies

The persistence and ecological impact of per- and poly-fluoroalkyl substances (PFAS) in water sources necessitate effective and energy-efficient treatment solutions. This study introduces a novel approach using cerium dioxide (CeO2) electrodes enhanced with oxygen vacancy (Ov) to catalyze the defluorination of PFAS. By leveraging the unique affinity between cerium and fluorine-containing species, our approach enables adsorptive preconcentration and catalytic degradation at low oxidation potentials (1.37 V vs. SHE). Demonstrating high removal and defluorination efficiencies of perfluorooctanoic acid (PFOA) at 94.0 % and 73.0 %, respectively, our approach also proves effective in the environmental matrix. It minimizes the impacts of co-existing natural organic matter and chloride ions, crucial benefits of operating at lower oxidation potentials. The role of Ov in CeO2 is validated by both experimental results and density functional theory modeling, demonstrating that these sites can activate the C-F bond and substantially reduce the energy barriers for defluorination. Consequently, our CeO2-based method not only achieves defluorination efficiencies comparable to more energy-intensive techniques but does so while requiring less than 0.62 kWh/m3 per order. This positions our approach as a promising, cost-effective alternative for the remediation of PFAS-contaminated waters, emphasizing its relevance and effectiveness in environmental remediation scenarios.

A sensitive and selective amperometric determination of perfluorooctanesulfonic acid on Mo2Ti2AlC3 MXene precursor-modified electrode

Various commercial and industrial products widely use highly toxic eight-carbon-chain perfluorooctanesulfonate (PFOS), posing a significant threat to the health of living organisms. In this study, the electrochemical detection of PFOS was achieved by developing a carbon paste electrode (CPE) using the Mo2Ti2AlC3 MAX phase. Mo2Ti2AlC3 was synthesized and directly used to construct the CPE. The electrochemical performance of the prepared sensor was tested using various electrochemical techniques, such as cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), differential pulse voltammetry (DPV), and amperometric titration. The developed electrochemical sensor exhibited two linear ranges from 0.001 to 0.09 μM and from 1.1 to 62.6 μM, with a detection limit of 0.04 nM. The sensor demonstrated high sensitivity, measuring 145.1 μA μM-1 cm-2, and a response time of 5 s for PFOS quantification at a working potential of 0.3 V. Additionally, the sensor demonstrated outstanding resistance to typical interfering chemicals. The applicability and reliability of the developed sensor for PFOS determination were further tested in real samples, yielding recoveries in the range of 92.6-108.2%, with relative standard deviation (RSD) values between 1.8% and 3.7%. The Mo2Ti2AlC3 MAX phase-based electrochemical sensor is simple, rapid, sensitive, and cost-effective, making it a promising approach for the quantification of PFOS in environmental water and soil samples.

Electrochemical advanced oxidation combined to electro-Fenton for effective treatment of perfluoroalkyl substances "PFAS" in water using a Magnéli phase-based anode

Per-and polyfluoroalkyl substances (PFAS), known as "forever chemicals", are posing a considerable threat to human health and the environment, that conventional treatment methods are unable to treat. In recent years, electrochemical advanced oxidation emerged as a promising technology for the degradation of recalcitrant pollutants such as PFAS. This work reports the degradation of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS), using a Magnéli phase-based anode type Ti4O7 by electro-oxidation and electro-oxidation combined with electro-Fenton. First the Ti4O7 anode was prepared from Rutile TiO2 powder and characterized, the results showed that the Ti n O2n-1 phase is the dominant phase. Afterward, the degradation of PFOA and PFOS was evaluated on the developed anode. After 5 hours of treatment, 52% and 82% of PFOA and PFOS were removed respectively. To improve this results electro-oxidation was combined with electro-Fenton, the degradation of both pollutants increased, 92% of PFOA was degraded and PFOS was totally removed after 5 hours of treatment. The energy consumption was also evaluated at t 1/2 which is defined as the time when half of the initial concentration of PFOA and PFOS was degraded. Combining the two degradation approaches showed promising results that need to be further optimized for potential application at large volumes.

Photocatalytic degradation of perfluorooctanoic acid (PFOA) from water: A mini review

Perfluorooctanoic acid (PFOA) has drawn increasing attention as a highly persistent organic pollutant. The inherent stability, rigidity and potential toxicities characteristics make it a challenge to develop efficient technologies to eliminate it from water. Photocatalytic technology, as one advanced method, has been widely used in the degradation of PFOA in water. In this review, recent progress in the design of photocatalysts including doping, defects engineering, heterojunction and surface modification to boost the photocatalytic performance toward PFOA is summarized. The relevant degradation mechanisms were also discussed in detail. Finally, future prospect and challenges are proposed. This review may provide new guidelines for researchers to design much more efficient photocatalysts applied in the elimination of PFOA.

Y-mediated optimization of 3DG-PbO2 anode for electrochemical degradation of PFOS

In our previous study, the three-dimensional graphene-modified PbO2 (3DG-PbO2) anode was prepared for the effective degradation of perfluorooctanesulfonat (PFOS) by the electrochemical oxidation process. However, the mineralization efficiency of PFOS at the 3DG-PbO2 anode still needs to be further improved due to the recalcitrance of PFOS. Thus, in this study, the yttrium (Y) was doped into the 3DG-PbO2 film to further improve the electrochemical activity of the PbO2 anode. To optimize the doping amount of Y, three Y and 3DG codoped PbO2 anodes were fabricated with different Y3+ concentrations of 5, 15, and 30 mM in the electroplating solution, which were named Y/3DG-PbO2-5, Y/3DG-PbO2-15 and Y/3DG-PbO2-30, respectively. The results of morphological, structural, and electrochemical characterization revealed that doping Y into the 3DG-PbO2 anode further refined the β-PbO2 crystals, increased the oxygen evolution overpotential and active sites, and reduced the electron transfer resistance, resulting in a superior electrocatalytic activity. Among all the prepared anodes, the Y/3DG-PbO2-15 anode exhibited the best activity for electrochemical oxidation of PFOS. After 120 min of electrolysis, the TOC removal efficiency was 80.89% with Y/3DG-PbO2-15 anode, greatly higher than 69.13% with 3DG-PbO2 anode. In addition, the effect of operating parameters on PFOS removal was analyzed by response surface, and the obtained optimum values of current density, initial PFOS concentration, pH, and Na2SO4 concentration were 50 mA/cm2, 12.21 mg/L, 5.39, and 0.01 M, respectively. Under the optimal conditions, the PFOS removal efficiency reached up to 97.16% after 40 min of electrolysis. The results of the present study confirmed that the Y/3DG-PbO2 was a promising anode for electrocatalytic oxidation of persistent organic pollutants.

The colorimetry and smartphone determination of perfluorooctane sulfonate based on cytidine 5'-monophosphate-capped gold nanoclusters with peroxidase-like activity

Besides being a luminescent material, cytidine 5'-monophosphate-capped gold nanoclusters (AuNCs@CMP) also show superior peroxidase-like activity which can promote TMB oxidation in the presence of H₂O₂, causing the solution to turn efficiently from pale to blue. However, the presence of perfluorooctane sulfonate (PFOS) in the above system inhibited TMB oxidation and bluing of the solution, consequently establishing a colorimetric platform of AuNCs/H₂O₂/TMB for PFOS determination. The results showed that it responded to PFOS over a wide range of 2.0-50 μM, with a limit of detection (LOD) as low as 150 nM. Furthermore, in-depth mechanism investigation revealed that, rather than the active site of the catalyst being occupied by PFOS, such a hypochromatic effect originated from depletion of the reactive oxygen species (ROS) by PFOS degradation, thereby also offering a unique strategy to scavenge the lethal toxicity of PFOS. In addition, the colorimetric response of AuNCs/H₂O₂/TMB to PFOS was extended to smartphone determination conveniently based on RGB values. Finally, the established platform was applied to PFOS determination both in soil extracts and in tap water with good recovery, which supplies a novel colorimetric platform for visual determination of PFOS in practice. The method has the advantages of being rapid, sensitive and highly selective, which highlight the design and construction of more systems for determination and elimination of lethal pollutants in environmental water.

Sources, Fate, and Detection of Dust-Associated Perfluoroalkyl and Polyfluoroalkyl Substances (PFAS): A Review

The occurrence of sand and dust storms (SDSs) is essential for the geochemical cycling of nutrients; however, it is considered a meteorological hazard common to arid regions because of the adverse impacts that SDSs brings with them. One common implication of SDSs is the transport and disposition of aerosols coated with anthropogenic contaminants. Studies have reported the presence of such contaminants in desert dust; however, similar findings related to ubiquitous emerging contaminants, such as per- and poly-fluoroalkyl substances (PFAS), have been relatively scarce in the literature. This article reviews and identifies the potential sources of dust-associated PFAS that can accumulate and spread across SDS-prone regions. Furthermore, PFAS exposure routes and their toxicity through bioaccumulation in rodents and mammals are discussed. The major challenge when dealing with emerging contaminants is their quantification and analysis from different environmental media, and these PFAS include known and unknown precursors that need to be quantified. Consequently, a review of various analytical methods capable of detecting different PFAS compounds embedded in various matrices is provided. This review will provide researchers with valuable information relevant to the presence, toxicity, and quantification of dust-associated PFAS to develop appropriate mitigation measures.

Electrochemical Advanced Oxidation of Perfluorooctanoic Acid: Mechanisms and Process Optimization with Kinetic Modeling

Electrochemical advanced oxidation processes (EAOPs) are promising technologies for perfluorooctanoic acid (PFOA) degradation, but the mechanisms and preferred pathways for PFOA mineralization remain unknown. Herein, we proposed a plausible primary pathway for electrochemical PFOA mineralization using density functional theory (DFT) simulations and experiments. We neglected the unique effects of the anode surface and treated anodes as electron sinks only to acquire a general pathway. This was the essential first step toward fully revealing the primary pathway applicable to all anodes. Systematically exploring the roles of valence band holes (h⁺), hydroxyl radicals (HO^•), and H₂O, we found that h⁺, whose contribution was previously underestimated, dominated PFOA mineralization. Notably, the primary pathway did not generate short-chain perfluoroalkyl carboxylic acids (PFCAs), which were previously thought to be the main degradation intermediates, but generated other polyfluorinated alkyl substances (PFASs) that were rapidly degraded upon formation. Also, we developed a simplified kinetic model, which considered all of the main processes (mass transfer with electromigration included, surface adsorption/desorption, and oxidation on the anode surface), to simulate PFOA degradation in EAOPs. Our model can predict PFOA concentration profiles under various current densities, initial PFOA concentrations, and flow velocities.