Unraveling microplastics removal in wastewater treatment plant: A comparative study of two wastewater treatment plants in Thailand

Release of microplastics from polymeric ultrafiltration membrane system for drinking water treatment under different operating conditions

Drinking water has emerged as an important route for microplastics (MPs) to enter the human body, prompting concerns about their adverse health impacts. Membrane filtration technology is widely recognized as an effective treatment solution for combating MP pollution in water. However, recent research disputes that polymeric membrane systems may serve as additional sources of MPs in drinking water. The aim of this research is to investigate MP release from ultrafiltration membrane systems under different operating conditions by providing concrete evidence, identifying the operational factors contributing to the release, and elucidating the underlying possible mechanisms. Two key pieces of evidence were found to support the assertion that MPs were released from membrane systems, i.e., negative removal efficiency and an alteration in MP compositions observed between feed and permeate samples. Surprisingly, the MPs released from the membrane system originated not only from the membrane material and its additives but also from plastic-made equipment and even the other polymers used in the system. Overall results reveal that destructive activities such as shear stress, mechanical abrasion, and chemical oxidation processes, along with the carrying of MPs from external sources, are identified as potential mechanisms driving the concentration increase and polymer composition shift of MPs in permeate water. This study enhances an understanding of MP pollution in drinking water caused by membrane technology, potentially spurring the development of mitigation strategies for this issue.

Pressure-Driven Membrane Processes for Removing Microplastics

The intense consumption of polymeric materials combined with poor waste management results in the dissemination of their fragments in the environment as micro- and nanoplastics. They are easily dispersed in stormwater, wastewater, and landfill leachate and carried towards rivers, lakes, and oceans, causing their contamination. In aqueous matrices, the use of membrane separation processes has stood out for the efficiency of removing these particulate contaminants, achieving removals of up to 100%. For this review article, we researched the removal of microplastics and nanoplastics by membrane processes whose driving force is the pressure gradient. The analysis focuses on the challenges found in the operation of microfiltration, ultrafiltration, nanofiltration, and reverse-osmosis systems, as well as on the innovations applied to the membranes, with comparisons of treatment systems and the peculiarities of each system and each aqueous matrix. We also point out weaknesses and opportunities for future studies so that these techniques, known to be capable of removing many other contaminants of emerging concern, can subsequently be widely applied in the removal of micro- and nanoplastics.

Prevalence and characteristics of microplastic contamination in soft drinks and potential consumer exposure

Microplastics (MPs) contamination in human food is a growing concern due to potential health risks. Recent studies have indicated that MPs have been found in various human tissues and organs, including the placenta, lungs, liver, and blood. This highlights the importance of investigating the presence and concentration of MPs in food products, as it directly relates to human health and safety. In this study, MP contamination was detected and characterized in commercially available soft drinks in Thailand. Nine popular soft drink brands in Thailand, packaged in different materials, including plastic bottles, aluminum cans, and glass bottles, were investigated. The results revealed that regardless of packaging type, all the soft drink brands tested contained MPs, with concentrations ranging from 2 ± 3 to 39 ± 12 items per liter. MPs in the 50-100 μm size range, primarily with a fragment-like morphology, were most commonly found. Given that the average person in Thailand consumes approximately 41.13 L of soft drinks annually, it is estimated that an individual could ingest between 81 and 1609 MPs yearly. These findings raise significant concerns about the potential health impacts of MP ingestion through soft drinks and underscore the need for further research and regulation.

Microplastic accumulation and transport in agricultural soils with long-term sewage sludge amendments

Land application of sewage sludge brings microplastic contamination to soil. However, studies regarding the occurrence and mobility of sludge-borne microplastics in soil are insufficient. In the present study, based on an experimental field, the effects of sludge application amount on the accumulation and migration of microplastics in 0-20 (upper) and 20-40 cm (lower) soil layers were evaluated. After 16 years of continuous sludge application (36 t/ha per year), the microplastic content and migration ratio in upper soil reached 6811 particles/kg and 148 %, which was about 5 and 20 times, respectively, higher than that of the control soil without sludge. The microplastics in upper and lower soil layers, were mainly 0.2-0.5 mm in size, mostly fibrous in shape, primarily transparent in color, and predominantly rayon in composition. Microplastic surfaces may persistently adsorb clay minerals and iron/titanium oxides from soil, posing potential environmental risks. Sludge application had a significant positive correlation with soil microplastic abundance, resulting in a good fit of predictive model constructed for microplastic accumulation in sludge-amended soils. These findings help to improve the knowledge on environmental behavior of microplastics in sludge-amended soil, and can provide a scientific basis for the regulation of microplastic pollution during sludge land application.

Occurrence Characteristics and Ecotoxic Effects of Microplastics in Environmental Media: a Mini Review

The issue of environmental pollution caused by the widespread presence of microplastics (MPs) in environmental media has garnered significant attention. However, research on MPs pollution has mainly focused on aquatic ecosystems in recent years. The sources and pollution characteristics of MPs in the environment, especially in solid waste, have not been well-described. Additionally, there are few reports on the ecotoxicity of MPs, which highlights the need to fill this gap. This review first summarizes the occurrence characteristics of MPs in water, soil, and marine environments, and then provides an overview of their toxic effects on organisms and the relevant mechanisms. This paper also provides an outlook on the hotspots of research on pollution characterization and ecotoxicity of MPs. Finally, this review aims to provide insights for future ecotoxicity control of MPs. Overall, this paper expands our understanding of the pollution characteristics and ecological toxicity of MPs in current environmental media, providing forward-looking guidance for future research.

Microplastics in aquatic systems: An in-depth review of current and potential water treatment processes

Plastic products, despite their undeniable utility in modern life, pose significant environmental challenges, particularly when it comes to recycling. A crucial concern is the pervasive introduction of microplastics (MPs) into aquatic ecosystems, with deleterious effects on marine organisms. This review presents a detailed examination of the methodologies developed for MPs removal in water treatment systems. Initially, investigating the most common types of MPs in wastewater, subsequently presenting methodologies for their precise identification and quantification in aquatic environments. Instruments such as scanning electron microscopy, dynamic light scattering, Fourier transform infrared spectroscopy, Raman spectroscopy, surface-enhanced Raman spectroscopy, and Raman tweezers stand out as powerful tools for studying MPs. The discussion then transitions to the exploration of both existing and emergent techniques for MPs removal in wastewater treatment plants and drinking water treatment plants. This includes a description of the core mechanisms that drive these techniques, with an emphasis on the latest research developments in MPs degradation. Present MPs removal methodologies, ranging from physical separation to chemical and biological adsorption and degradation, offer varied advantages and constraints. Addressing the MPs contamination problem in its entirety remains a significant challenge. In conclusion, the review offers a succinct overview of each technique and forwards recommendations for future research, highlighting the pressing nature of this environmental dilemma.

Understanding microplastic presence in different wastewater treatment processes: Removal efficiency and source identification

Municipal effluents discharged from wastewater treatment plants (WWTPs) are a considerable source of microplastics in the environment. The dynamic profiles of microplastics in treatment units in WWTPs with different treatment processes remain unclear. This study quantitatively analyzed microplastics in wastewater samples collected from different treatment units in two tertiary treatment plants with distinct processes. The influents contained an average of 15.5 ± 3.5 particles/L and 38.5 ± 2.5 particles/L in the two WWTPs with in the oxidation ditch process and the integrated fixed-film activated sludge process, respectively. Interestingly, microplastic concentrations in the influent were more influenced by the population density in the served area than sewage volume or served population equivalent. Throughout the treatment process, concentrations were reduced to 1.5 ± 0.5 particles/L and 1.0 ± 1.0 particles/L in the final effluents, representing an overall decrease of 90% and 97%, in WWTPs with the oxidation ditch process and integrated fixed-film activated sludge process, respectively. A significant proportion of the microplastics were removed during the primary treatment stage in both WWTPs, with better performance for foam, film, line-shaped and large-sized microplastics. Most microplastics were accumulated in activated sludge, indicating its key role as the primary sink in WWTPs. The multiple correspondence analysis identified laundry washing and daily necessities such as packaging and containers as the major contributors to microplastics in WWTPs. The study proposed recommendations for upgrading WWTPs, modifying designs, and implementing strategies to reduce microplastic sources, aiming to minimize the release of microplastics into the environment. These findings can shed lights on the sources of microplastics in WWTPs, and advance our understanding of the mechanisms for more effective microplastic removals in wastewater treatment technologies in future applications.

Plastic waste management in recycling facilities: Intentionally generated MPs as an emerging contaminant

There is little knowledge about microplastic (MP) pollution in plastic recycling facility (PRF) wastewater. In this study, MPs in the wastewaters of four PRFs located in Türkiye were characterized for size, shape, color, and polymer types after sieving from 5,000 µm to the lowest 75 µm with seven sieves. The wet peroxide oxidation procedure was applied before attenuated total reflectance fourier transform infrared spectroscopy analysis for polymer identification. Polyethylene, and polypropylene were the dominant (75 % of total count) MP types within 22 polymer types. Average hit qualities of polymers increased from 69 % to above 84 % for the device software (OPUS) and open software (OpenSpecy). The abundance of MPs was determined as 53,987 MPs/L and 0.8 g MP/L for mixed PRFs 7,582 MPs/L and 4.6 g/L for the LDPE recycling facility, and 2,196 MPs/L and 0.06 g MPs/L for the granulation cooling water by count and weight, respectively. Small-sized MPs are found in the bottom sample much more than the surface and effluent samples in the washing tank. This indicated that MPs adsorbed the pollutants settled in the washing tank due to adsorbed pollution/biofilm. A maximum of 4.6 kg MP/ton of plastic recycled can be discharged as MPs that can be recovered. Considering the plastics recycling capacity, discharged MPs in these PRFs are possibly above 30,000 tons.

Application of advanced oxidation processes for the removal of micro/nanoplastics from water: A review

Micro/nanoplastics (MNPs) have been increasingly found in environments, food, and organisms, arousing wide public concerns. MNPs may enter food chains through water, posing a threat to human health. Therefore, efficient and environmentally friendly technologies are needed to remove MNPs from contaminated aqueous environments. Advanced oxidation processes (AOPs) produce a vast amount of active species, such as hydroxyl radicals (·OH), known for their strong oxidation capacity. As a result, an increasing number of researchers have focused on using AOPs to decompose and remove MNPs from water. This review summarizes the progress in researches on the removal of MNPs from water by AOPs, including ultraviolet photolysis, ozone oxidation, photocatalysis, Fenton oxidation, electrocatalysis, persulfate oxidation, and plasma oxidation, etc. The removal efficiencies of these AOPs for MNPs in water and the influencing factors are comprehensively analyzed, meanwhile, the oxidation mechanisms and reaction pathways are also discussed in detail. Most AOPs can achieve the degradation of MNPs, mainly manifest as the decrease of particle size and the increase of mass loss, but the mineralization rate is low, thus requiring further optimization for improved performance. Investigating various AOPs is crucial for achieving the complete decomposition of MNPs in water. AOPs will undoubtedly play a vital role in the future for the removal of MNPs from water.

Microplastics in aquatic environments: A comprehensive review of toxicity, removal, and remediation strategies

The occurrence of microplastics (MPs) in aquatic environments has been a global concern because they are toxic and persistent and may serve as a vector for many legacies and emerging pollutants. MPs are discharged to aquatic environments from different sources, especially from wastewater plants (WWPs), causing severe impacts on aquatic organisms. This study mainly aims to review the Toxicity of MPs along with plastic additives in aquatic organisms at various trophic compartments and available remediation methods/strategies for MPs in aquatic environments. Occurrences of oxidative stress, neurotoxicity, and alterations in enzyme activity, growth, and feeding performance were identical in fish due to MPs toxicity. On the other hand, growth inhibition and ROS formation were observed in most of the microalgae species. In zooplankton, potential impacts were acceleration of premature molting, growth retardation, mortality increase, feeding behaviour, lipid accumulation, and decreased reproduction activity. MPs togather with additive contaminants could also exert some toxicological impacts on polychaete, including neurotoxicity, destabilization of the cytoskeleton, reduced feeding rate, growth, survivability and burrowing ability, weight loss, and high rate of mRNA transcription. Among different chemical and biological treatments for MPs, high removal rates have been reported for coagulation and filtration (>86.5 %), electrocoagulation (>90 %), advanced oxidation process (AOPs) (30 % to 95 %), primary sedimentation/Grit chamber (16.5 % to 58.84 %), adsorption removal technique (>95 %), magnetic filtration (78 % to 93 %), oil film extraction (>95 %), and density separation (95 % to 100 %). However, desirable extraction methods are required for large-scale research in MPs removal from aquatic environments.

Land use-based characterization and source apportionment of microplastics in urban storm runoffs in a tropical region

Urban stormwater runoff has been suggested as one important land-based pathway of microplastics (MPs) entering the oceans, in which the abundance and characteristics of MPs may be influenced by urban land use types. However, little information has been reported regarding this, especially in the tropical monsoon region. This study first reports the MPs in urban stormwater runoffs in a tropical monsoon region that were collected from four typical urban land use types, including industrial, highways, commercial, and residential areas. The average MP particle count and mass concentration were measured as 4.7 ± 3.5 particles/L and 3.8 ± 2.9 mg/L, respectively. MP abundances showed clear urban land use gradients following the order of industrial > transportation > commercial > residential area. In terms of the seasonal variation in MP abundances, a slightly increasing particle count in the dry season was noted for the residential site. Source apportionment of MPs in stormwater runoffs was demonstrated based on the land use type, particle morphology, and chemical compositions. With the simple apportionment approach, approximately 85% of the MP sources were able to be identified in the industrial, transportation, and residential sites. However, the commercial site showed high variability in terms of the morphology and polymer type of MPs. Furthermore, significantly positive correlations between MP abundance and runoff turbidity, TSS, COD, and rainfall intensity were identified, while, no significant correlation was found between MP characteristics and selected water quality/meteorological parameters.

An assessment of the impact of structure and type of microplastics on ultrafiltration technology for microplastic remediation

Microplastic, which is of size less than 5 mm, is gaining a lot of attention as it has become a new arising contaminant because of its ecophysiology impact on the aquatic environment. These microplastics are found in freshwater or drinking water and are the major carriers of pollutants. Removal of this microplastic can be done through the primary treatment process, secondary treatment process, and tertiary treatment process. One approach for microplastic remediation is ultrafiltration technology, which involves passing water through a membrane with small pores to filter out the microplastics. However, the efficiency of this technology can be affected by the structure and type of microplastics present in the water. New strategies can be created to improve the technology and increase its efficacy in removing microplastics from water by knowing how various types and shapes of microplastics react during ultrafiltration. The filter-based technique, that is, ultrafiltration has achieved the best performance for the removal of microplastic. But with the ultrafiltration, too some microplastic that are of sizes less than of ultrafiltration membrane passes through the filter and enters the food chain. Accumulation of this microplastic on the membrane also leads to membrane fouling. Through this review article, we have assessed the impact of the structure, size, and type of MPs on ultrafiltration technology for microplastic remediation, with that how these factors affect the efficiency of the filtration process and challenges occur during filtration.

Reduction of Ultrafiltration Membrane Fouling by the Pretreatment Removal of Emerging Pollutants: A Review

Ultrafiltration (UF) processes exhibit high removal efficiencies for suspended solids and organic macromolecules, while UF membrane fouling is the biggest obstacle affecting the wide application of UF technology. To solve this problem, various pretreatment measures, including coagulation, adsorption, and advanced oxidation, for application prior to UF processes have been proposed and applied in actual water treatment processes. Previously, researchers mainly focused on the contribution of natural macromolecular pollutants to UF membrane fouling, while the mechanisms of the influence of emerging pollutants (EPs) in UF processes (such as antibiotics, microplastics, antibiotic resistance genes, etc.) on membrane fouling still need to be determined. This review introduces the removal efficiency and separation mechanism for EPs for pretreatments combined with UF membrane separation technology and evaluates the degree of membrane fouling based on the UF membrane's materials/pores and the structural characteristics of the cake layer. This paper shows that the current membrane separation process should be actively developed with the aim of overcoming specific problems in order to meet the technical requirements for the efficient separation of EPs.