Co-treatment of landfill leachate with urban wastewater by chemical, physical and biological processes: Fenton oxidation preserves autochthonous bacterial community in the activated sludge process

Elucidation of the stress mechanisms on activated sludge stability induced by yttrium oxide nanoparticles with cytotoxicity: Performance deterioration, biointerface variation and microbial response

As technoscience advances, widespread use of nanoparticles (NPs) has resulted in environmental risks. This study focuses on the potential stress of 0-200 mg/L yttrium oxide (Y2O3) NPs on the activated sludge stability. Y2O3 NPs progressively suppressed nitrification, caused significant NO2- accumulation (200 mg/L) and diminished activities of key functional enzymes. Deteriorated flocculation corroborates the Y2O3 NPs' destruction. Extracellular polymeric substances were lessened, yet amplified microbial metabolites prove the microbial counteraction coping with Y2O3 NPs' cytotoxicity. Plausible blockage of different protein channels contributed to the wane in biological nitrogen-removal capacity. Plus, 50 mg/L Y2O3 NPs stimulated the β-glucan production. When exceeding 100 mg/L, plentiful Y2O3 NPs aggregate on sludge-surface, which inhibits nutrients transfer and metabolism. Furthermore, ammonia-oxidizing bacteria shifted from Nitrosomonas to Nitrosospira with Y2O3 NPs increase. Reduction in Nitrospira, Saccharimonada-genera, and Microlunatus further corroborates the impairment of pollutants removal. PICRUSt2 prediction demonstrates Y2O3 NPs impedes nitrogen and glycolytic metabolic pathway.

The role of biodegradable plastics in lignite anaerobic digestion: Changes of organics transformation and metabolic pathway

Biodegradable plastics (BPs) and lignite, both rich in organic matter, present significant challenges for efficient conversion into clean energy. This study examined the anaerobic co-digestion of BPs and lignite under controlled laboratory conditions. The results demonstrated that the co-digestion of polylactic acid (PLA) and lignite (at a 1:2 mass ratio, with 5 g PLA and 10 g lignite as the model system) rapidly acclimated to the anaerobic environment, enhancing cumulative biogas production by 57 % compared to the mono-digestion of lignite alone. Synergistic fermentation significantly increased the production of organic small molecules while effectively degrading recalcitrant substances, including hydroxyl, aromatic, and methylene groups. Euryarchaeota emerged as the dominant phylum, with its abundance increasing by 118.4 %. Gene abundance for the carbon dioxide-to-methane conversion pathway increased by 60.1 %, confirming it as the primary methane metabolic pathway. These findings provide a novel method for the conversion and utilization of BPs and lignite.

Bacterial community dynamics in a biofilm-based process after electro-assisted Fenton pre-treatment of real olive mill wastewater

In this work, the effect of the electro-assisted Fenton (EAF) process on the bacterial community of a moving bed biofilm reactor (MBBR) for olive mill wastewater (OMW) co-treatment with urban wastewater (UWW) was investigated. According to metagenomic analysis, pre-treatment by EAF, while removing total phenols (TPHs) up to 84 % ± 3 % and improving biodegradability of OMW from 0.38 to 0.62, led to the emergence of bacterial genera in the MBBR (R2) that were not detected under conditions without pre-treatment (R1). Indeed, in that condition, Candidatus Competibacter replaced Amaricoccus as dominant denitrifying bacteria. In both cases, the bacterial community composition matched with high simultaneous nitrification-denitrification efficiency (up to 98 %). Finally, Chlorobium (2.5-4.1 %), sulphate-reducing bacteria and Geobacter (up to 1.6 ± 0.4 %), anaerobic bacteria that utilise iron oxides, were observed exclusively with EAF application, suggesting potential for the development of new integrated microbial electrochemical systems.

Effect of intermittent water flow on biodegradation of organic micropollutants in the hyporheic zone

Water scarcity in the Mediterranean area has increased the number of intermittent rivers. Recently, hyporheic zones (HZ) of intermittent rivers have gained attention since a substantial part of the stream's natural purification capacity is located within these zones. Thus, understanding the flow dynamics in HZs is crucial for gaining insights into the degradation of organic micropollutants. A lab-scale study using column experiments was conducted in an attempt to elucidate the environmental processes accounting for the biodegradation capacity of the HZ under flow intermittency. A mixture of six compounds including pesticides (chloranthraniliprole, fluopyram and trifloxystrobin) and pharmaceuticals (venlafaxine, amisulpride and paroxetine) spiked at 1 μg/L level was used for degradation kinetic studies and at 1 mg/L for transformation products identification using suspect/non-target liquid chromatography high-resolution mass spectrometry approaches. The experiments lasted 60 days, divided into two 14-day phases: one before and one after a 5-week desiccation period. Bacterial community was charaterized by high-throughput DNA sequencing. The results suggested that intermittent flows stimulated the biodegradation of three compounds namely fluopyram, trifloxystrobin and venlafaxine, showing a large range of biodegradation profiles in batch water/sediment testing system according to OECD 308 tests. Biodegradation rate enhancement was ascribed to the occurrence of additional transformation routes after the desiccation period of river sediment, with the formation of new transformation products reported for the first time in the present work. 16S rDNA sequencing revealed that the desiccation period favored the growth of nitrifying and denitrifying bacteria which could partially explain the emergence of the new transformation pathways and most specifically those leading to N-oxide derivatives. Identification of transformation products also revealed that reductive transformation routes were relevant for this study, being dehydrogenation, dehalogenation, ether bond cleavage and sulfone reduction into sulphide important reactions. These results suggest that the intermittent flow conditions can influence the HZ biodegradation capacity.

Comparative impact analysis of nitrate reduction by typical components of natural organic compounds in magnetite-bearing riparian zones

As the key interface, the nitrate removal capacity of riparian zones is receiving close attention. Although naturally occurring organic compounds in this environment play a pivotal role in shaping microbial communities and influencing the nitrate removal capacity, the relevant research is inadequate. Given the complexity of riparian environments, in this study, we added representative natural organic matter (fulvic acid, butyric acid, naphthalene, starch, and sodium bicarbonate) as carbon conditions and incorporated magnetite to simulate riparian zone components. The study investigated the nitrate degradation efficiency and microbial responses under different natural carbon conditions in real iron-containing environments. Butyric acid exhibited the most efficient nitrate reduction, followed in descending order by naphthalene, starch, sodium bicarbonate, and humic acid. However, this did not imply that butyric acid efficiently removed nitrogen; instead, the nitrogen would circulate in the environment in the form of ammonium. Denitrification and DNRA were the primary drivers of nitrate reduction in each system, while naphthalene and humic acid systems also exhibited nitrification and mineralization. Nitrogen-fixing bacteria represent a unique microbial community in the butyrate system. Further, the synergistic degradation of naphthalene and nitrate demonstrated significant potential applications. High-throughput sequencing revealed that carbon conditions exerted selective pressure on microorganisms, driving Fe (Ⅱ)/Fe (Ⅲ) transformation by shaping the microbial community structure and influencing the nitrogen cycling process.

Combination of electro-oxidation and biological processes for lindane landfill leachate treatment: simultaneous degradation of contaminants and biological reduction of electro-generated chloride-derived by-products

Real lindane landfill leachate (HCH-LL) is characterised by high chlorinated organic compounds concentrations (primarily hexachlorocyclohexane (HCH) isomers and degradation products generated during more than 40 years of ageing), posing environmental and human health risks. In this work, the co-treatment of real HCH-LL (pre-treated via electro-oxidation (EO)) and urban wastewater using an activated sludge process operated in an anoxic/oxic sequencing batch (A/O-SBR) mode was investigated. EO tests were conducted employing either a boron-doped diamond (BDD) anode or a dimensionally stable anode (DSA), resulting in effective HCH isomers removal (>93 % after 20 Ah/L). Chloride-derived by-products (CDBPs) such as free chlorine (up to 828 mg Cl2/L), chlorate (up to 972 mg/L) (formed with EO (DSA)) and perchlorate (up to 1830 mg/L) (with EO (BDD)) persisted after the treatment. EO (DSA) resulted in inhibitory effects (up to 100 % respiration inhibition) on the biological process. Conversely, EO (BDD) negligibly affected biological respiration (up to 20 % less than without pre-treatment), while perchlorate bio-reduction by A/O-SBR was poor (28 %). Acetate addition in pre-treated HCH-LL for perchlorate bio-reduction allowed to achieve simultaneous contaminants removal (> 99 %) and CDBPs reduction (up to 100 %). Biodegradation and bio-adsorption tests without pre-treatment showed partial HCH isomers removal (about 40 %) and poor bio-adsorption.

Insights into the response of nitrogen metabolism to sulfamethoxazole contamination in constructed wetlands with varied substrates

This study conducted an analysis of the variations in nitrogen metabolism pathways within constructed wetlands (CWs) using zeolite (CW-Z), ceramsite (CW-C), and lava (CW-L) under high concentration sulfamethoxazole (SMX) stress. The introduction of SMX hindered the formation of hydrogen bonds on the substrate surfaces; however, these surfaces still maintained a dense and thick biofilm. CW-Z exhibited superior removal efficiencies for ammonium nitrogen (NH4+-N) and nitrate nitrogen (NO3--N) compared to CW-C and CW-L, with removal rates of 92.54 ± 2.88 % and 89.39 ± 6.74 %, respectively. Interestingly, the proportion of genes involved in nitrification, denitrification and nitrate reduction genes in CW-C (36.05 %) were higher than that in CW-C (29.81 %) and CW-L (29.70 %) but the interactions among nitrogen functional bacteria in CW-Z were much more complex. Further analysis of the nitrogen metabolism pathway indicated that under CW-Z enhanced dissimilatory nitrate reduction SMX stress, while CW-L enhanced assimilatory nitrate reduction process compared to CW-C.

Large-Scale Integration of Amplicon Data Reveals Massive Diversity within Saprospirales, Mostly Originating from Saline Environments

The order Saprospirales, a group of bacteria involved in complex degradation pathways, comprises three officially described families: Saprospiraceae, Lewinellaceae, and Haliscomenobacteraceae. These collectively contain 17 genera and 31 species. The current knowledge on Saprospirales diversity is the product of traditional isolation methods, with the inherited limitations of culture-based approaches. This study utilized the extensive information available in public sequence repositories combined with recent analytical tools to evaluate the global evidence-based diversity of the Saprospirales order. Our analysis resulted in 1183 novel molecular families, 15,033 novel molecular genera, and 188 K novel molecular species. Of those, 7 novel families, 464 novel genera, and 1565 species appeared in abundances at ≥0.1%. Saprospirales were detected in various environments, such as saline water, freshwater, soil, various hosts, wastewater treatment plants, and other bioreactors. Overall, saline water was the environment showing the highest prevalence of Saprospirales, with bioreactors and wastewater treatment plants being the environments where they occurred with the highest abundance. Lewinellaceae was the family containing the majority of the most prevalent species detected, while Saprospiraceae was the family with the majority of the most abundant species found. This analysis should prime researchers to further explore, in a more targeted way, the Saprospirales proportion of microbial dark matter.

Changes of nitrogen and phosphorus removal pattern caused by alternating aerobic/anoxia from the perspective of microbial characteristics

The purpose of this study was to compare the impact of different numbers of alternating aerobic/anoxic (A/O) cycles on pollutant removal. Three sequential batch reactors (SBRs) with varying numbers of alternating A/O cycles were established. Under the tertiary anoxic operating conditions, the removal efficiencies of chemical oxygen demand (COD), ammonia nitrogen (NH₄⁺-N), total nitrogen (TN), and total phosphorus (TP) were 88.73%, 89.56%, 72.15%, and 77.61%, respectively. Besides, alternating A/O affected the dominant microbial community relative abundance (Proteobacteria and Bacteroidetes) and increased microbial richness and diversity. It also increased the relative abundance of aerobic denitrifying, heterotrophic nitrifying, and denitrifying phosphorus removal bacteria to change N and P removal patterns. Furthermore, the abundance of carbohydrate metabolism and amino acid metabolism was improved by alternating A/O to improve organic matter and TN removal.

Improving organic matter and nutrients removal and minimizing sludge production in landfill leachate pre-treatment by Fenton process through a comprehensive response surface methodology approach

Landfill leachate (LL) represents a very complex effluent difficult to treat and to manage which usually requires a chemical pre-treatment. In this study, response surface methodology (RSM) was used to identify the optimum operating conditions of the Fenton process as a pre-treatment of LL in order to reduce the high organic content and simultaneously optimize the BOD₅:TN:TP ratio. The dosages of Fenton process reagents, namely Fe²⁺ and H₂O₂, were used as variables for the implementation of RSM. Chemical oxygen demand (COD), five-days biochemical oxygen demand (BOD₅), total nitrogen (TN), total phosphorus (TP) removals (and simultaneously BOD₅:TN:TP ratio), sludge-to-iron ratio (SIR) and organic removal-to-sludge ratio (ORSR) were selected as target responses. This approach considered the SIR and ORSR parameters which are a useful tool for assessing sludge formation during the process along with organic matter removal. The variables (H₂O₂ and Fe²⁺ concentrations) significantly affected the responses, as the role of oxidation mechanism is dominant with respect to coagulation one. The pH for the process was fixed to 2.8 while the treatment time was set to 2 h. The optimum operational conditions obtained by perturbation and 3D surface plot, were found to be 4262 mg/L and 5104 mg/L for Fe²⁺ and H₂O₂, respectively (H₂O₂/Fe²⁺ molar ratio = 2) with COD, BOD₅, TN and TP removals of 70%, 67%, 84% and 96% respectively, while SIR and ORSR final values were 1.15 L/mol and 33.79 g/L respectively, in accordance with models-predicted values. Moreover, the initial unbalanced BOD₅:TN:TP ratio (9:1:1) was significantly improved (100:6:1), making the effluent suitable for a subsequent biological treatment. The investigated approach allowed to optimize the removal of organic load and nutrients as well as to minimize the sludge formation in Fenton process, providing a useful tool for the operation and management of LL pre-treatment.

Deciphering the microbial community structures and functions of wastewater treatment at high-altitude area

Introduction: The proper operation of wastewater treatment plants is a key factor in maintaining a stable river and lake environment. Low purification efficiency in winter is a common problem in high-altitude wastewater treatment plants (WWTPs), and analysis of the microbial community involved in the sewage treatment process at high-altitude can provide valuable references for improving this problem. Methods: In this study, the bacterial communities of high- and low-altitude WWTPs were investigated using Illumina high-throughput sequencing (HTS). The interaction between microbial community and environmental variables were explored by co-occurrence correlation network. Results: At genus level, Thauera (5.2%), unclassified_Rhodocyclaceae (3.0%), Dokdonella (2.5%), and Ferribacterium (2.5%) were the dominant genera in high-altitude group. The abundance of nitrogen and phosphorus removal bacteria were higher in high-altitude group (10.2% and 1.3%, respectively) than in low-altitude group (5.4% and 0.6%, respectively). Redundancy analysis (RDA) and co-occurrence network analysis showed that altitude, ultraviolet index (UVI), pH, dissolved oxygen (DO) and total nitrogen (TN) were the dominated environmental factors (p < 0.05) affecting microbial community assembly, and these five variables explained 21.4%, 20.3%, 16.9%, 11.5%, and 8.2% of the bacterial assembly of AS communities. Discussion: The community diversity of high-altitude group was lower than that of low-altitude group, and WWTPs of high-altitude aeras had a unique microbial community structure. Low temperature and strong UVI are pivotal factors contributing to the reduced diversity of activated sludge microbial communities at high-altitudes.