Temperature and bath gas composition dependence of effective fluorescence lifetimes of toluene excited at 266nm

Excitation wavelength dependence of the fluorescence lifetime of anisole

Photo-physical models that describe the pressure- and temperature-dependent fluorescence quantum yield of organic fluorescence tracers rely on an accurate prediction of the initial excited-state population, collision-dependent relaxation processes, and state-dependent relaxation processes. In case the initial excited-state population distribution reached after the laser excitation equals on average the thermal distribution, the fluorescence quantum yield becomes pressure independent. This initial distribution critically depends on the temperature-dependent ground-state population before excitation as well as the excitation wavelength. The ability to predict this behavior is a critical check for the validity of the existing photophysical models. The dependence of the effective fluorescence lifetime of anisole on the excitation wavelength (256-270 nm) was investigated at temperatures between 325 and 525 K for pressures between 1 and 4 bar. For each temperature, a unique excitation wavelength was found where the fluorescence lifetime is pressure-independent. The comparison of the experimental results with the predictions based on the established photophysical step-ladder models revealed a systematic underestimation of the required excitation photon energies for direct excitation into the thermalized level. An improved modeling approach based on quantum chemistry calculations for implementing simulated excitation spectra and state-dependent transition probabilities overcomes these limitations. Our results show for the example of anisole that the fluorescence step-ladder models that exist for aromatic fluorescence tracers must be modified to correctly predict the effect of the excitation wavelength.

Single-shot time-gated fluorescence lifetime imaging using three-frame images

Qualitative and quantitative measurements of complex flows demand for fast single-shot fluorescence lifetime imaging (FLI) technology with high precision. A method, single-shot time-gated fluorescence lifetime imaging using three-frame images (TFI-TGFLI), is presented. To our knowledge, it is the first work to combine a three-gate rapid lifetime determination (RLD) scheme and a four-channel framing camera to achieve this goal. Different from previously proposed two-gate RLD schemes, TFI-TGFLI can provide a wider lifetime range 0.6 ~ 13ns with reasonable precision. The performances of the proposed approach have been examined by both Monte-Carlo simulations and toluene seeded gas mixing jet diagnosis experiments. The measured average lifetimes of the whole excited areas agree well with the results obtained by the streak camera, and they are 7.6ns (N₂ = 7L/min; O₂ < 0.1L/min) and 2.6ns (N₂ = 19L/min; O₂ = 1L/min) with the standard deviations of 1.7ns and 0.8ns among the lifetime image pixels, respectively. The concentration distributions of the quenchers and fluorescent species were further analyzed, and they are consistent with the experimental settings.

Advanced Laser-Based Techniques for Gas-Phase Diagnostics in Combustion and Aerospace Engineering

Gaining information of species, temperature, and velocity distributions in turbulent combustion and high-speed reactive flows is challenging, particularly for conducting measurements without influencing the experimental object itself. The use of optical and spectroscopic techniques, and in particular laser-based diagnostics, has shown outstanding abilities for performing non-intrusive in situ diagnostics. The development of instrumentation, such as robust lasers with high pulse energy, ultra-short pulse duration, and high repetition rate along with digitized cameras exhibiting high sensitivity, large dynamic range, and frame rates on the order of MHz, has opened up for temporally and spatially resolved volumetric measurements of extreme dynamics and complexities. The aim of this article is to present selected important laser-based techniques for gas-phase diagnostics focusing on their applications in combustion and aerospace engineering. Applicable laser-based techniques for investigations of turbulent flows and combustion such as planar laser-induced fluorescence, Raman and Rayleigh scattering, coherent anti-Stokes Raman scattering, laser-induced grating scattering, particle image velocimetry, laser Doppler anemometry, and tomographic imaging are reviewed and described with some background physics. In addition, demands on instrumentation are further discussed to give insight in the possibilities that are offered by laser flow diagnostics.

Fluorescence characteristics of the fuel tracers triethylamine and trimethylamine for the investigation of fuel distribution in internal combustion engines

Laser-induced fluorescence based on fuel tracers like amines is a suitable measurement technique for mixing studies in internal combustion (IC) engines. Triethylamine has often been used in gasoline IC engines; however, no detailed fluorescence characterization for excitation at 263 or 266 nm is available. Trimethylamine (TMA) exhibits high potential as a gaseous fuel tracer but little information about TMA fluorescence is currently available. A picosecond laser source combined with a streak camera equipped with a spectrograph was used to determine the spectral fluorescence emission and fluorescence decay time of both tracers. The tracers were investigated at various temperatures and pressures in a calibration cell with nitrogen as bath gas. The results provide an in-depth understanding of the fluorescence characteristics of both tracers and allow assessment of their application to the investigation of fuel distribution in IC engines.

Formaldehyde preparation methods for pressure and temperature dependent laser-induced fluorescence measurements

Formaldehyde is an excellent tracer for the early phase of ignition of hydrocarbon fuels and can be used, e.g., for characterization of single droplet ignition. However, due to its fast thermal decomposition at elevated temperatures and pressures, the determination of concentration fields from laser-induced fluorescence (LIF) measurements is difficult. In this paper, we address LIF measurements of this important combustion intermediate using a calibration cell. Here, formaldehyde is created from evaporation of paraformaldehyde. We discuss three setups for preparation of formaldehyde/air mixtures with respect to their usability for well-defined heating of formaldehyde/air mixtures. The "basic setup" uses a resist heater around the measurement cell for investigation of formaldehyde near vacuum conditions or formaldehyde/air samples after sequential admixing of air. The second setup, described for the first time in detail here, takes advantage of a constant flow formaldehyde/air regime which uses preheated air to reduce the necessary time for gas heating. We used the constant flow system to measure new pressure dependent LIF excitation spectra in the 343 nm spectral region (41 (4) absorption band of formaldehyde). The third setup, based on a novel concept for fast gas heating via excitation of SF6 (chemically inert gas) using a TEA (transverse excitation at atmospheric pressure) CO2 laser, allows to further minimize both gas heating time and thermal decomposition. Here, an admixture of CO2 is served for real time temperature measurement based on Raman scattering. The applicability of the fast laser heating system has been demonstrated with gas mixtures of SF6 + air, SF6 + N2, as well as SF6 + N2 + CO2 at 1 bar total pressure.

In-cylinder temperature measurements via time-correlated single-photon counting of toluene laser-induced fluorescence through a fiber-based sensor

In a near-production internal combustion engine, the effective fluorescence lifetime of toluene was determined by time-correlated single-photon counting with a minimally invasive fiber-optic spark-plug sensor. The lifetime measurement provided continuous crank-angle-resolved measurements of gas temperature. Proof-of-concept experiments in a motored four-cylinder spark-ignition engine were evaluated with a time resolution of 500 μs, yielding temperature precision of 25 K (standard deviation) at top-dead center. In these experiments, 10% toluene was added to the nonfluorescent base fuel iso-octane. Fluorescence lifetimes were related to temperature via calibration measurements in a high temperature pressure vessel, with the data fitted to a functional dependence derived from a previously published phenomenological model.