Micromechanical analysis on the compaction of tetrahedral particles

Structure-Property Relationship of Amorphous Maltitol as Tableting Excipient

Maltitol shows interesting properties compared with mannitol or sorbitol, two other polyols, which are widely used as a pharmaceutical excipients for tablet compaction. For this study, the properties of an amorphous polyol, maltitol, were investigated using a tablet press simulator. The aim of this study was to evaluate the behavior of amorphous maltitol compared to SweetPearl® P 200, a pure product, and SweetPearl® P 300 DC, a textured crystalline maltitol excipient for direct compression. The physicochemical and pharmacotechnical properties were compared, revealing a major change in properties after amorphization. The study of the tabletability, mean yield pressure, elastic properties, etc. shows that the compression behavior of amorphous powders has been significantly altered. The results showed specific properties of amorphous maltitol with good tabletability at low compaction pressure. The stability of the amorphous and the evolution of its behavior in compression were then studied, showing a direct link between its recrystallization and the change in its properties. The use of a stabilizing agent, maltotriitol, slowed down the recrystallization, maintaining the specific properties of the amorphous material in compression for a longer period of time.

Discrete Element Method Modelling of the Diametral Compression of Starch Agglomerates

Starch agglomerates are widely applied in the pharmaceutical, agricultural, and food industries. The formation of potato starch tablets and their diametral compression were simulated numerically and verified in a laboratory experiment to analyse the microscopic mechanisms of the compaction and the origins of their breakage strength. Discrete element method (DEM) simulations were performed using EDEM software. Samples comprised of 120,000 spherical particles with radii normally distributed in the range of 5–36 μm were compacted in a cylindrical die with a diameter of 2.5 cm. The linear elastic–plastic constitutive contact model with a parallel bonded-particle model (BPM) was used to model the diametral compression. DEM simulations indicated that the BPM, together with the linear elastic–plastic contact model, could describe the brittle, semi-brittle, or ductile breakage mode, depending on the ratio of the strength to Young’s modulus of the bond and the bond-to-contact elasticity ratio. Experiments confirmed the findings of the DEM simulations and indicated that potato starch (PS) agglomerates can behave as a brittle, semi-brittle, or ductile material, depending on the applied binder. The PS agglomerates without any additives behaved as a semi-brittle material. The addition of 5% of ground sugar resulted in the brittle breakage mode. The addition of 5% gluten resulted in the ductile breakage mode.

Numerical Modeling for Simulation of Compaction of Refractory Materials for Secondary Steelmaking

The purpose of this work is to simulate the powder compaction of refractory materials, using the discrete element method (DEM). The capability of two cohesive contact models, implemented in different DEM packages, to simulate the compaction of a mixture of two refractory materials (dead burnt magnesia (MgO) and calcined alumina (Al₂O₃)) was analyzed, and the simulation results were compared with experimental data. The maximum force applied by the punch and the porosity and final shape quality of the compact were examined. As a starting point, the influence of Young's modulus (E), the cohesion energy density (CED), and the diameter of the Al₂O₃ particles (D) on the results was analyzed. This analysis allowed to distinguish that E and CED were the most influential factors. Therefore, a more extensive examination of these two factors was performed afterward, using a fixed value of D. The analysis of the combined effect of these factors made it possible to calibrate the DEM models, and consequently, after this calibration, the compacts had an adequate final shape quality and the maximum force applied in the simulations matched with the experimental one. However, the porosity of the simulated compacts was higher than that of the real ones. To reduce the porosity of the compacts, lower values of D were also modeled. Consequently, the relative deviation of the porosity was reduced from 40-50% to 20%, using a value of D equal to 0.15 mm.