Inverse gas chromatography applications: a review

Quantitative Analysis of Wettability and Its Transition Mechanism in Carbonate Rocks Based on Surface Energy Characterization

Wettability significantly influences crude oil occurrence within reservoirs and hydrocarbon recovery efficiency. Carbonate rock wettability undergoes substantial alteration under elevated temperatures or asphalt adsorption. To quantitatively assess the impacts of temperature and asphalt on carbonate wettability and analyze its transformation mechanisms, inverse gas chromatography was employed to measure surface energy of Ordovician carbonate samples from Tahe Oilfield across 30-130 °C. With increasing temperature, the nonpolar surface energy of carbonate rocks first decreases and then increases, accompanied by enhanced basic component. Utilizing Young's equation and Van Oss theory, theoretical values of interfacial tensions and water contact angles in rock-oil-water systems were calculated based on surface energy components of rock, petroleum, and water, enabling quantitative wettability evaluation. Results demonstrate strengthened water-wetting characteristics with temperature elevation, primarily governed by increased acidic and basic components of carbonate surface energy. More polar carbonate samples exhibit superior hydrophilicity compared to less polar counterparts at equivalent temperatures. The oil-wetting enhancement mechanism through asphalt adsorption arises from ultralow asphalt-carbonate interfacial tension at ambient conditions, facilitating spontaneous asphalt adsorption. Asphalt-coated surfaces dramatically increase water contact angles in light oil-water systems, intensifying oil-wetting behavior. Optimal recovery temperatures range in 60-100 °C for fractured carbonate reservoirs containing light oil and in 100-110 °C for asphalt-rich reservoirs.

The role of surface deformation on responsivity of the pillared layer metal-organic framework DUT-8(Ni)

A unique feature of flexible metal-organic frameworks (MOFs) is their ability to respond dynamically towards molecular stimuli by structural transitions, resulting in pore-opening and closing processes. One of the most intriguing modes is the "gating", where the material transforms from the dense to the porous state. The conditions required for the solid phase structural transition are controlled by the kinetic barriers, including nucleation of the new phase commencing on the crystallite's outer surface. Thus, surface deformation may influence the nucleation, enabling deliberate tailoring of the responsivity. In the present contribution, we investigate how chemical surface treatments (surface deformation) affect the gate opening characteristics of a typical representative of gate pressure MOFs, DUT-8(Ni) ([Ni2(ndc)2(dabco)] n , ndc = 2,6-naphthalenedicarboxylate, dabco = 1,4-diazabicyclo[2.2.2]octane). A combination of various complementary advanced characterization techniques, such as NMR, nanoFTIR, terahertz, in situ XPS, in situ EPR spectroscopies, and inverse gas chromatography, are applied to unravel the changes in surface energy and mechanism of surface deformation.

Investigation of thermodynamic and solubility properties of poly (4-methyl styrene - alt - maleic anhydride) and poly (4-methyl styrene - alt - n-propyl maleimide) copolymers by inverse gas chromatography

Poly (4-methyl styrene - alt - maleic anhydride) (PMS-A) copolymer was synthesized by free radical polymerization, and then modified with n-propyl amine through ring opening of maleic anhydride units to prepare modified poly (4-methyl styrene - alt - n-propyl maleimide) (PMS-I) copolymer. FT-IR analysis confirmed the composition of these copolymers. Thermogravimetric analysis (TGA), glass transition temperature (Tg), and gel permeation chromatography (GPC) were investigated for the copolymers. Some thermodynamic and physicochemical properties were determined for different groups of test solutes at infinite dilution by inverse gas chromatography (IGC) in the temperature ranges 373-393 K and 373-433 K for the PMS-A and the PMS-I copolymers, respectively. The physicochemical characterization of the IGC included the determination of the molar heat enthalpy of sorption, mixing and vaporization (ΔH1S,ΔH1∞,ΔHV), weight fraction activity coefficient,Ω1∞, Flory-Huggins interaction parameters, X12∞ at infinite dilution, Hildebrand solubility parameter, δ2, total and partial Hansen solubility parameters, δT,δd,δp,δh. The results showed that the solubility of the PMS-A copolymer in nonpolar solutes is poor but moderate for the PMS-I copolymer. The solubility of the PMS-A copolymer in benzene and toluene solutes is moderate, but it is good for the PMS-I copolymer. The solubility of the PMS-A copolymer in ketones, halogens, nitriles, acetates, heterocyclic, and alcohol solutes is good, but the solubility of the PMS-I copolymer with these solutes is the best. Values of the Hildebrand solubility parameters of the PMS-A and PMS-I copolymers ranged from 17.57 - 16.73 and 19.48 - 18.06, respectively. In addition, the total Hansen solubility parameters ranged from 18.82 - 17.12 and 16.65 - 15.20.

Surface Energy Distribution of Modified Carbon Black and Interfacial Interactions of Filled Rubber Composites

Carbon black (CB) modification to achieve both homogeneous dispersion and strong interfacial interactions is a challenging subject for high-performance tread rubber composites. The effect of modification on CB surface characteristics is difficult to analyze experimentally, resulting in an uncomprehensive knowledge of the factors influencing interfacial interactions. In this study, 4,4'-diaminodiphenyldisulfide (APDS) was utilized to modify CB. Through molecular simulation techniques, the interfacial binding energy and surface energy distribution were obtained to analyze the interfacial interaction and determine the influence of modifiers on strong binding sites on the CB surface. The strong binding sites were preserved, and the overall interaction was enhanced. The experimental results demonstrated that CB dispersion was evidently improved, and strong interfacial interactions were effectively maintained, verifying the results of molecular simulation. This study elucidated the critical effect of strong binding sites on the CB surface regarding interfacial interactions and also provided theoretical guidance for CB modification. The method of calculating the surface energy distribution of fillers by molecular simulation provides a new efficient strategy for interfacial characterization and modifier evaluation.

The influence of surface properties on the cooperative behavior of powdered milks

This study comprehensively analyses various powdered milk samples to elucidate their structural, surface, and mechanical properties. Through detailed examination, diverse characteristics among the samples were observed, shedding light on their behavior under different conditions. Notably, findings reveal intriguing insights into surface energy profiles, Harkins spreading coefficient, powder rheological properties, and sound absorption efficiency of the powdered milk samples. The intricate relationship between surface properties and bulk characteristics influenced the cooperative behavior of freely poured and consolidated milk powder beds, resulting in varying flowability from free-flowing to cohesive. Surface energy played a significant role in cohesiveness and dispersibility, with milk fat acting as a key mediator leading to changes in bulk dynamic-mechanical stiffness. These findings hold practical implications for formulating innovative aerosol-based dairy and cosmetic products, thereby enhancing everyday experiences.

Going beyond the Ordered Bulk: A Perspective on the Use of the Cambridge Structural Database for Predictive Materials Design

When Olga Kennard founded the Cambridge Crystallographic Data Centre in 1965, the Cambridge Structural Database was a pioneering attempt to collect scientific data in a standard format. Since then, it has evolved into an indispensable resource in contemporary molecular materials science, with over 1.25 million structures and comprehensive software tools for searching, visualizing and analyzing the data. In this perspective, we discuss the use of the CSD and CCDC tools to address the multiscale challenge of predictive materials design. We provide an overview of the core capabilities of the CSD and CCDC software and demonstrate their application to a range of materials design problems with recent case studies drawn from topical research areas, focusing in particular on the use of data mining and machine learning techniques. We also identify several challenges that can be addressed with existing capabilities or through new capabilities with varying levels of development effort.

New Method to Probe the Surface Properties of Polymer Thin Films by Two-Dimensional (2D) Inverse Gas Chromatography (iGC)

Polymer-based functional surface coatings are extensively used in advanced technologies, including optics, energy, and environmental applications. Surface thermodynamic properties profoundly impact the molecular interactions that control interfacial behaviors, such as adhesion and wettability, which in turn dictate coating processes and performance. Conventionally, contact angle measurements are used to assess the surface energy of polymer films and coatings, where the wettability of a surface is assessed using probe fluids (liquid drops). However, contact angle measurement oftentimes can be nontrivial due to the roughness or chemical heterogeneity of the solid surface, as well as the potential for the liquid drop to swell or even dissolve the material being measured. Alternatively, inverse gas chromatography (iGC) is a versatile technique to measure surface thermodynamics and Lewis acid-base properties while also providing environmental control such as temperature and humidity. Despite these benefits, the application of iGC has been limited to powders or fibers, while the direct measurement of supported thin films or coatings is still a nascent area of research. This creates a challenge when using iGC as a comprehensive platform for measuring the physicochemical properties of solid surfaces. Here, we demonstrate how to effectively use iGC to characterize the surface energy of supported polymer thin films by using a two-dimensional (2D) film holder and modifying operational controls, such as the concentration range of the injected gas probe molecules. This enables the precise control of surface coverage required for analyzing samples having minimal surface area, such as thin films. Poly(methyl methacrylate) (PMMA) was employed as a benchmark to determine suitable iGC parameters and to validate our approach on polymer thin films. The seminal work presented here expands the capability of state-of-the-art iGC to embrace supported thin films (2D iGC) that could either be smooth or display texture/roughness (patterned films) as well as coatings with heterogeneous chemical/structural composition.

Amorphous solid dispersion of a binary formulation with felodipine and HPMC for 3D printed floating tablets

This study focuses on the combination of three-dimensional printing (3DP) and amorphous solid dispersion (ASD) technologies for the manufacturing of gastroretentive floating tablets. Employing hot melt extrusion (HME) and fused deposition modeling (FDM), the study investigates the development of drug-loaded filaments and 3D printed (3DP) tablets containing felodipine as model drug and hydroxypropyl methylcellulose (HPMC) as the polymeric carrier. Prior to fabrication, solubility parameter estimation and molecular dynamics simulations were applied to predict drug-polymer interactions, which are crucial for ASD formation. Physical bulk and surface characterization complemented the quality control of both drug-loaded filaments and 3DP tablets. The analysis confirmed a successful amorphous dispersion of felodipine within the polymeric matrix. Furthermore, the low infill percentage and enclosed design of the 3DP tablet allowed for obtaining low-density systems. This structure resulted in buoyancy during the entire drug release process until a complete dissolution of the 3DP tablets (more than 8 h) was attained. The particular design made it possible for a single polymer to achieve a zero-order controlled release of the drug, which is considered the ideal kinetics for a gastroretentive system. Accordingly, this study can be seen as an advancement in ASD formulation for 3DP technology within pharmaceutics.

Reproducibility of inverse gas chromatography under infinite dilution: Results and interpretations of an interlaboratory study

Over the last years, inverse gas chromatography (IGC) proved to be a versatile and sensitive analytical technique for physicochemical properties. However, the comparability of results obtained by different users and devices remains a topic for debate. This is the first time, an interlaboratory study using different types of IGC instruments is reported. Eight organizations with different IGC devices defined a common lab measurement protocol to analyse two standard materials, silica and lactose. All data was collected in a standard result form and has been treated identically with the objective to identify experimentally observed differences and not potentially different data treatments. The calculated values of the dispersive surface energy vary quite significantly (silica: 22 mJ/m2 - 34 mJ/m2, lactose 37 mJ/m2 - 51 mJ/m2) and so do the ISP values and retention volumes for both materials. This points towards significant and seemingly undiscovered differences in the operation of the instruments and the obtained underlying primary data, even under the premise of standard conditions. Variations are independent of the instrument type and uncertainties in flow rates or the injected quantities of probe molecules may be potential factors for the differences. This interlaboratory study demonstrates that the IGC is a very sensitive analytical tool, which detects minor changes, but it also shows that for a proper comparison, the measurement conditions have to be checked with great care. A publicly available standard protocol and material, for which this study can be seen as a starting point, is still needed to judge on the measurements and the resulting parameters more objectively.

Impact of coagulation solvent interactions on porous morphology evolution in cellulose xerogels

The role of coagulation solvent interactions on the pore formation mechanism in cellulose xerogels was investigated using single-step coagulation baths. A series of cellulose xerogels were fabricated from cotton yarns partially dissolved in ionic liquid (i.e., 1-ethyl-3-methylimidazolium acetate) and then immersed in one of seven different coagulation baths. These samples were evaluated using N2 physisorption, inverse gas chromatography, and X-ray photoelectron spectroscopy. The regenerated cellulose orientation and resultant surface hydrophilicity was found to be dependent on solvent solubility interactions with an emphasis on polar interaction and dispersion force strength. More importantly, the xerogel specific surface area dramatically decreased from 100 m2g-1 to 0.278 m2g-1 with increasing hydrophilicity, confirming the importance of controlled cellulose orientation during the coagulation step of cellulose xerogel fabrication. These results have been used to propose a new pore formation mechanism in cellulose xerogels and provide recommendations towards the development of controllable porosity during xerogel fabrication.

Study of Disordered Mesoporous Silica Regarding Intrinsic Compound Affinity to the Carrier and Drug-Accessible Surface Area

There is increasing research interest in using mesoporous silica for the delivery of poorly water-soluble drugs that are stabilized in a noncrystalline form. Most research has been done on ordered silica, whereas far fewer studies have been published on using nonordered mesoporous silica, and little is known about intrinsic drug affinity to the silica surface. The present mechanistic study uses inverse gas chromatography (IGC) to analyze the surface energies of three different commercially available disordered mesoporous silica grades in the gas phase. Using the more drug-like probe molecule octane instead of nitrogen, the concept of a "drug-accessible surface area" is hereby introduced, and the effect on drug monolayer capacity is addressed. In addition, enthalpic interactions of molecules with the silica surface were calculated based on molecular mechanics, and entropic energy contributions of volatiles were estimated considering molecular flexibility. These free energy contributions were used in a regression model, giving a successful comparison with experimental desorption energies from IGC. It is proposed that a simplified model for drugs based only on the enthalpic interactions can provide an affinity ranking to the silica surface. Following this preformulation research on mesoporous silica, future studies may harness the presented concepts to guide formulation scientists.

Perspectives on the Wetting of Solids in Pharmaceutical Systems

PURPOSE

The ability of water and aqueous solutions to wet relatively nonpolar pharmaceutical solids during the processing and administration of solid dosage forms is an important part of development.

RESULTS

Various factors, both fundamental and technological, which are important to wettability are reviewed and analyzed. Initially, the ideal thermodynamic importance of liquid surface tension and solid surface energetics, determined by the contact angle and the polarity of the solid surface, are established. Then, emphasis is placed on various factors that change the surface energetics due to crystal defects, polymorphism, varying Miller Indices, crystal habit, amorphous structure, variable surface concentration of components in a formulation mixture, surface roughness, and complex pore structure. Case studies cover single component systems (APIs and excipients), binary mixtures (amorphous solid dispersions and physical mixtures), multicomponent systems (granules and tablets), as well as disintegration and dissolution of solid oral dosage forms.

CONCLUSIONS

This perspective and analysis indicates the primary importance of understanding and modifying solid surface energetics, surface chemical and physical heterogeneities, and pore structure to promote wettability in pharmaceutical systems.

Determination of Hansen solubility parameters of water-soluble proteins using UV-vis spectrophotometry

Determination of solubility parameters by dissolution tests are difficult for some valuable molecules, such as proteins, where the quantities available are small, UV-vis spectroscopy can determine dissolved concentrations of even small amounts of material, but accurate determination of dissolution is difficult in relatively poor solvents, due to difficulty with constructing a reliable calibration curve. In this work we report a new simple procedure to determine the relative dissolution of proteins in various solvents using UV vis spectroscopy for the determination of Hansen solubility parameters (HSP) of proteins. This method allows qualitative determination of the amounts of BSA dissolved in various solvents. The amounts of BSA dissolved in each solvent, can then be used to rank solvents as good or bad for HSP calculation purpose, which gives more reliable ranking than observation alone in dissolution tests. To be able to evaluate the HSP of any solid material, the solubility of the tested material in a range of solvents needs to be determined. Solvents are then scored as good or bad based on observations and from the known properties of those solvents, the HSP of the solute molecule in question can be calculated. Here, bovine serum albumin (BSA) was used as a model protein, but the procedure reported here can be applied to any soluble protein or other macromolecule with a clear UV/vis adsorption peak. This procedure requires the tested material to be highly soluble in water, therefore eliminating the need for the preparation of many standard solutions of BSA in different solvents. Only a set of standard solutions of protein in water is required. UV-vis spectroscopy was used to analyze the remaining solid resuspended in water after centrifugation of solutions of BSA dissolved in other solvents to separate any undissolved protein. The HSP of BSA obtained via this procedure was compared to values previously obtained for BSA using other methods. A very good agreement between the HSP obtained in this work with the that reported by Houen et al. which used amino acid analysis for the estimation of the solubility of BSA in various organic solvents.

Understanding Sorption Mechanisms Directly from Isotherms

Currently, more than 100 isotherm models coexist for the six IUPAC isotherm types. However, no mechanistic insights can be reached when several models, each claiming a different mechanism, fit an experimental isotherm equally well. More frequently, popular isotherm models [such as the site-specific models like Langmuir, Brunauer-Emmett-Teller (BET), and Guggenheim-Anderson-de Boer (GAB)] have been applied to real and complex systems that break their basic assumptions. To overcome such conundrums, we establish a universal approach to model all isotherm types, attributing the difference to the sorbate-sorbate and sorbate-surface interactions in a systematic manner. We have generalized the language of the traditional sorption models (such as the monolayer capacity and the BET constant) to the model-free concepts of partitioning and association coefficients that can be applied across the isotherm types. Through such a generalization, the apparent contradictions, caused by applying the site-specific models alongside with cross-sectional area of sorbates for the purpose of surface area determination, can be eliminated straightforwardly.

Comparison of olefin/paraffin separation by ionic liquid and polymeric ionic liquid stationary phases containing silver(I) ion using one-dimensional and multidimensional gas chromatography

Silver(I) ions have been used in various studies as components within polymer membranes or ionic liquids (ILs) to enable separation of olefins from paraffins. Polymeric ionic liquids (PILs) are a class of polymers synthesized from IL monomers and typically possess higher thermal and chemical stability than the ILs from which they are formed. Until now, very little is known about the difference in strength of silver(I) ion-olefin interactions when they take place in an IL compared to a PIL. In this work, the chromatographic separation of olefins by stationary phases composed of silver(I) bis[(trifluoromethyl)sulfonyl]imide ([Ag⁺][NTf₂^-]) incorporated into the 1-hexyl-3-methylimidazolium NTf₂ ([HMIM⁺][NTf₂^-]) IL and poly(1-hexyl-3-vinylimidazolium NTf₂) (poly([HVIM⁺][NTf₂^-])) PIL at varying concentrations was investigated. Olefins were more highly retained by silver(I) ions in PILs than in ILs as the silver(I) salt concentration in the stationary was increased. The potential separation power of silver(I)-containing IL and PIL stationary phases in comprehensive two-dimensional gas chromatography (GC×GC) was compared to the conventional one-dimensional system. The separation selectivity of alkenes and alkynes from paraffins was significantly increased, while dienes and aromatic compounds showed insignificant changes in retention. The chemical structural features of IL and PIL that enhance silver(I) ion stability and olefin separation were investigated by using silver(I) trifluoromethanesulfonate ([Ag⁺][OTf^-]), 1-decyl-3-methylimidazolium NTf₂ ([DMIM⁺][NTf₂^-]) IL, poly(1-decyl-3-vinylimidazolium NTf₂ (poly([DVIM⁺][NTf₂^-])) PIL, [HMIM⁺][OTf^-] IL and poly([HVIM⁺][OTf^-]) PIL. Longer alkyl substituents appended to the IL (and PIL) cation increased the strength of silver(I) olefin interaction, and [OTf^-] anions in the IL (and PIL) tended to preserve silver(I) ion from thermal reduction, while also retaining olefins less than the [NTf₂^-]-containing columns. In general, silver(I) ions in PILs possessing analogous chemical structures to ILs exhibited higher silver(I) ion-olefin interaction strength but were less thermally stable.

Understanding Nanocellulose-Water Interactions: Turning a Detriment into an Asset

Modern technology has enabled the isolation of nanocellulose from plant-based fibers, and the current trend focuses on utilizing nanocellulose in a broad range of sustainable materials applications. Water is generally seen as a detrimental component when in contact with nanocellulose-based materials, just like it is harmful for traditional cellulosic materials such as paper or cardboard. However, water is an integral component in plants, and many applications of nanocellulose already accept the presence of water or make use of it. This review gives a comprehensive account of nanocellulose-water interactions and their repercussions in all key areas of contemporary research: fundamental physical chemistry, chemical modification of nanocellulose, materials applications, and analytical methods to map the water interactions and the effect of water on a nanocellulose matrix.

Restructuring the Interface of Silk-Polycaprolactone Biocomposites Using Rigid-Flexible Agents

Natural fiber-reinforced biocomposites with excellent mechanical and biological properties have attractive prospects for internal medical devices. However, poor interfacial adhesion between natural silk fiber and the polymer matrix has been a disturbing issue for such applications. Herein, rigid-flexible agents, such as polydopamine (PDA) and epoxy soybean oil (ESO), were introduced to enhance the interfacial adhesion between Antheraea pernyi (Ap) silk and a common medical polymer, polycaprolactone (PCL). We compared two strategies of depositing PDA first (Ap-PDA-ESO) and grafting ESO first (Ap-ESO-PDA). The rigid-flexible interfacial agents introduced multiple molecular interactions at the silk-PCL interface. The "Ap-PDA-ESO" strategy exhibited a greater enhancement in interfacial adhesion, and interfacial toughening mechanisms were proposed. This work sheds light on engineering strong and tough silk fiber-based biocomposites for biomedical applications.

Characterization of polar surface groups on siliceous materials by inverse gas chromatography and the enthalpy-entropy compensation effect

Surface-modified porous silica is a well-established composite material. To improve its embedding and application behavior, adsorption studies of various probe molecules have been performed using the technique of inverse gas chromatography (IGC). For this purpose, IGC experiments were carried out in the infinite dilution mode on macro-porous micro glass spheres before and after surface modification with (3-mercaptopropyl)trimethoxysilane. To provide information about the polar interactions between probe molecules and the silica surface, in particular, eleven polar molecules have been injected. In summary, the free surface energy for pristine silica ( γ S t o t a l = 229 mJ/m²) and for (3-mercaptopropyl)trimethoxysilane-modified silica ( γ S t o t a l = 135 mJ/m²) indicates a reduced wettability after surface modification. This is due to the reduction of the polar component of the free surface energy ( γ S S P ) from 191 mJ/m² to 105 mJ/m². Simultaneously, with the reduction of surface silanol groups caused by surface modification of silica and, therefore, the decrease in polar interactions, a substantial loss of Lewis acidity was observed by various IGC approaches. Experiments with all silica materials have been conducted at temperatures in the range from 90°C to 120°C to determine the thermodynamic parameters, such as adsorption enthalpy ( Δ H a d s ) and adsorption entropy ( Δ S a d s ), using the Arrhenius regression procedure evaluating the IGC data. With the help of the enthalpy-entropy compensation, two types of adsorption complexes are assumed between polar probe molecules and the silica surface because of different isokinetic temperatures. Identical adsorption complexes with an isokinetic temperature of 370°C have been assigned to alkanes and weakly interacting polar probes such as benzene, toluene, dichloromethane, and chloroform. Polar probe molecules with typical functional groups such as OH, CO, and CN, having the ability to form hydrogen bonds to the silica surface, exhibit a lower isokinetic temperature of 60°C. Quantum chemical calculations of the probe molecules on a non-hydroxylated and hydroxylated silica cluster supported the formation of hydrogen bonds in the case of a strong polar adsorption complex with a bonding distance of 1.7 nm-1.9 nm to the silica surface.

Impact of the Polymer Backbone Structure on the Separation Properties of New Stationary Phases Based on Tricyclononenes

The main purpose of this paper is to compare the chromatographic properties of capillary columns prepared with polymers with different backbone structures and to demonstrate the possibility of polymer differentiation via inverse gas chromatography. With the use of addition and metathesis types of polymerization of tricyclononenes, two new stationary phases were prepared. The metathesis polymer contained double bonds in the polymeric backbone while the backbone of the addition polymer was fully saturated and relatively mobile. A comparison of the separation and adsorption properties of new phases with conventional gas chromatography (GC) stationary phases clearly indicated their non-polar characteristics. However, the difference in the polymer structure appeared to have very little effect on the stationary phase separation properties, so other parameters were used for polymer characterization. The thermodynamic parameters of the sorption of alkanes and aromatic compounds in both polymeric stationary phases were also very similar; however, the entropy of sorption for hydrocarbons with seven or more carbon atoms was different for the two polymers. An evaluation of the specific surface energy of the stationary phases also allowed us to discriminate the two stationary phases.

Separation of plastic wastes using froth flotation - An overview

Despite various initiatives and efforts, plastic solid waste (PSW) has become a major global problem due to decades of relentless use of plastics. Since non-biodegradable plastics can persist in the environment for hundreds of years, threatening animal and human life, discarding them into the environment is not a viable option. Plastic recycling is a critical research area that requires urgent attention since less than 10% of the seven billion tons of globally generated plastic waste has been recycled so far. With recent technological developments, it is now possible to recycle many types of PSW using a variety of methods. This review provides an overview of the froth flotation technology that is currently being researched for PSW recycling. Fundamental working principles, the current state of the development, and limitations of this technique are reviewed. It is suggested that froth flotation with continuous development has tremendous potential to result in a more efficient and environmentally friendly approach to PSW recycling.

Determination of BET Specific Surface Area of Hydrate-Anhydrate Systems Susceptible to Phase Transformation Using Inverse Gas Chromatography

Specific surface area (SSA) is an important parameter in drug development that affects other downstream pharmaceutical properties of interest such as reactivity, stability, dissolution, and ultimately bioavailability. Traditionally, the Brunauer-Emmett-Teller (BET) SSA of pharmaceutical powders is measured via gas adsorption (nitrogen or krypton) that is preceded by a prolonged degassing step under low pressure. This degassing step may not be suitable for certain pharmaceutical hydrates that are susceptible to dehydration and phase transformation under reduced pressure and humidity conditions. Therefore, inverse gas chromatography (IGC) was explored as a reliable alternate technique for determining the SSA of model anhydrate-hydrate systems (trehalose and thiamine hydrochloride) that are prone to such phase transformation during SSA measurement. Both trehalose dihydrate and thiamine HCl non-stoichiometric hydrate were found to undergo partial phase transformation to anhydrous forms during BET analysis via degassing and gas adsorption. In contrast, these hydrates remained stable during surface area analysis using IGC owing to measurements under controlled relative humidity. Thus, IGC proved to be a viable technique for SSA measurement of pharmaceutical hydrates without compromising their physical stability.

Machine Learning Quantitative Structure-Property Relationships as a Function of Ionic Liquid Cations for the Gas-Ionic Liquid Partition Coefficient of Hydrocarbons

Ionic liquids (ILs) are known for their unique characteristics as solvents and electrolytes. Therefore, new ILs are being developed and adapted as innovative chemical environments for different applications in which their properties need to be understood on a molecular level. Computational data-driven methods provide means for understanding of properties at molecular level, and quantitative structure-property relationships (QSPRs) provide the framework for this. This framework is commonly used to study the properties of molecules in ILs as an environment. The opposite situation where the property is considered as a function of the ionic liquid does not exist. The aim of the present study was to supplement this perspective with new knowledge and to develop QSPRs that would allow the understanding of molecular interactions in ionic liquids based on the structure of the cationic moiety. A wide range of applications in electrochemistry, separation and extraction chemistry depends on the partitioning of solutes between the ionic liquid and the surrounding environment that is characterized by the gas-ionic liquid partition coefficient. To model this property as a function of the structure of a cationic counterpart, a series of ionic liquids was selected with a common bis-(trifluoromethylsulfonyl)-imide anion, [Tf2N]-, for benzene, hexane and cyclohexane. MLR, SVR and GPR machine learning approaches were used to derive data-driven models and their performance was compared. The cross-validation coefficients of determination in the range 0.71-0.93 along with other performance statistics indicated a strong accuracy of models for all data series and machine learning methods. The analysis and interpretation of descriptors revealed that generally higher lipophilicity and dispersion interaction capability, and lower polarity in the cations induces a higher partition coefficient for benzene, hexane, cyclohexane and hydrocarbons in general. The applicability domain analysis of models concluded that there were no highly influential outliers and the models are applicable to a wide selection of cation families with variable size, polarity and aliphatic or aromatic nature.

Effects of Cosmetic Emulsions on the Surface Properties of Mongolian Hair

In the light of clean beauty and sustainability requirements emerging in the personal care market, the urgent need for the replacement of silicones in hair conditioners-with comparable performance and customer experience-has been highlighted in the industry. In this context, the goal of the present study was to investigate the physical effects of different silicone-free conditioner formulations on Mongolian hair after damage due to bleaching and compare the results to property changes induced by a classical silicone-containing formulation. To that end, the morphology, structure, and composition of strands and individual fibers of this hair type were characterized before and after bleaching by means of optical microscopy, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). It is shown that oxidative bleaching causes significant damage to the native hair surface, leading to local depletion or even large-area removal of the outer hydrophobic lipid layer. This results in enhanced wettability of the bleached hair by water (as confirmed by contact angle measurements) and is accompanied by an undesired loss of hair gloss and softness. Upon treatment with suitable cosmetic emulsions, the natural hydrophobicity of intact Mongolian hair can be partially or fully restored, with silicone-free formulations having effects similar to those of established silicone-containing products. The successive influence of bleaching and conditioning was further monitored using inverse gas chromatography (iGC), a technique that probes changes in surface energetics and polarity over an ensemble of an entire hair strand through interactions with specific molecules at the solid/gas interface. The resulting data mirror the macroscopic behavior of the bleached/conditioned hair and provide a quantitative scale for measuring damage and repair effects. Most notably, the effect of bleaching and subsequent conditioning on the haptic perception of hair strands could also be quantified with the aid of a biomimetic measurement system, which identifies increased friction (both tactile and sliding) as the major cause for the strawy feel of bleached hair and indicates successful relubrication after treatment with suitable conditioner formulations. Finally, the different physical properties determined for native, bleached, and reconditioned Mongolian hair are found to be reflected in application-oriented tests, namely in vitro measurements of wet and dry combing work. Overall, the data collected in this work shed novel light on the surface properties of Mongolian hair and highlight that effective hair conditioning after damage can be achieved without silicones in advanced cosmetic emulsions based on octyldodecyl myristate and glyceryl oleate.

Quantitative Determination of the Hydrophobicity of Nanoparticles

The hydrophobicity of nanoparticles (NPs) is one of the most important physicochemical properties that determines their agglomeration state under various environmental conditions. When studying nano-bio interactions, it is found that the hydrophobicity of NPs plays a predominant role in mediating the biological response and toxicity of the NPs. Although many methods have been developed to qualitatively or quantitatively determine hydrophobicity, there is not yet a scientific consensus on the standard of characterizing the hydrophobicity of NPs. We have developed a novel optical method, called the maximum particle dispersion (MPD), for quantitatively characterizing the hydrophobicity of NPs. The principle of measurement of the MPD method lies in the control of the aggregation state of the NPs via manipulating the van der Waals interactions between NPs across a dispersion liquid. We have scrutinized the mechanism of the MPD method using a combination of dynamic light scattering and atomic force microscopy and further verified the MPD method using a completely independent dye adsorption method. The MPD method demonstrated great promise to be developed into an easy-to-use and cost-effective method for quantitatively characterizing the hydrophobicity of NPs.

Hydroxypropyl Cellulose for Drug Precipitation Inhibition: From the Potential of Molecular Interactions to Performance Considering Microrheology

There has been recent interest in using hydroxypropyl cellulose (HPC) for supersaturating drug formulations. This study investigated the potential for molecular HPC interactions with the model drug celecoxib by integrating novel approaches in the field of drug supersaturation analysis. Following an initial polymer characterization study, quantum-chemical calculations and molecular dynamics simulations were complemented with results of inverse gas chromatography and broadband diffusing wave spectroscopy. HPC performance was studied regarding drug solubilization and kinetics of desupersaturation using different grades (i.e., HPC-UL, SSL, SL, and L). The results suggested that the potential contribution of dispersive interactions and hydrogen bonding depended strongly on the absence or presence of the aqueous phase. It was proposed that aggregation of HPC polymer chains provided a complex heterogeneity of molecular environments with more or less excluded water for drug interaction. In precipitation experiments at a low aqueous polymer concentration (i.e., 0.01%, w/w), grades L and SL appeared to sustain drug supersaturation better than SSL and UL. However, UL was particularly effective in drug solubilization at pH 6.8. Thus, a better understanding of drug-polymer interactions is important for formulation development, and polymer blends may be used to harness the combined advantages of individual polymer grades.

Application of inverse gas chromatography in the surface characterization of diethanol amine modified polystyrene based polymer

In the present work, diethanol amine modified polystyrene based polymer (PVBC-Diethanol amine) was synthesized and characterized, then surface properties of the polymer were examined by inverse gas chromatography method at infinite dilution. The retention diagrams obtained based on the interaction of polar and nonpolar probes with the polymer were drawn over a temperature range from 30 to 55 °C. Through the diagrams, the dispersive component of the surface free energy, g S D of the polymer surface, and the specific enthalpy of adsorption, DH A S , of probes on the polymer were also calculated. Lewis acid, K A , and Lewis base, K D , parameters of PVBC-Diethanol amine surface were determined. The values of K A and K D indicated that PVBC-Diethanol amine surface exhibited a basic behavior.

Opposing Effects of Additives in Dry Milling and Tableting of Organic Particles

Applying additives and excipients during the dry processing of fine particles is a common measure to control the particle–particle interactions, to specifically influence the powder properties and to enhance the process efficiency or product quality. In this study, the impacts of a particulate lubricant, a nano-disperse flow additive and liquid grinding aids on the dry fine milling and subsequent tableting of the ground material were investigated for three different organic model compounds. It is presented that the three additive classes cause varying and partly opposing effects during these process steps. Especially the lubricant and the grinding aids were shown to increase the efficiency of the milling process as well as the product fineness of the ground material, and to avoid critical product adhesions on the machine surfaces. Thereby, stable and efficient grinding conditions were partially not possible without the addition of such additives. However, as these positive effects are attributed to a reduction of the adhesive forces between the particles, much lower tablet strengths were achieved for these additives. This propagation of powder, and in turn, final product properties over whole process chains, has not been studied in detail so far. It was further revealed that the material behavior and the microstructure of the product particles is decisive for the processing as well, which is why additive effects may be product-specific and can even be suppressed under certain processing conditions. In comparison to the process performances, the powder properties and surface energies of the product particles were less influenced by the additives. On the contrary, particle-based morphologies or deformation behavior seem to play a major role in comparison to inorganic materials. Thus, it can be stated that global bulk properties and surface energies provide first indications of powder behavior and susceptibility. However, additional specific properties need to be evaluated to more clearly understand the influences of additives.

Comparison of Surface Properties of Sepiolite and Palygorskite: Surface Energy and Nanoroughness

The surface properties of two sepiolite samples and one palygorskite sample were compared using inverse gas chromatography (IGC). Samples were previously conditioned at appropriate temperatures for the removal of all zeolitic water. Dispersive (or Lifshitz–van der Waals) component of the surface energy (γ_s^d), specific interactions (−ΔG_a^s) with π electron donor bases (1-alkenes), and nanomorphology indices (IMχT) based on the injections of cycloalkanes and a branched alkane were measured. From IGC data, at 240 °C, it was found that the palygorskite was clearly distinguished from the sepiolites. The palygorskite possessed a lower γ_s^d, larger −ΔG_a^s with 1-alkenes, and remarkably higher IMχT. Slight differences could also be observed between the two sepiolite samples with the same origin. The results were rationalized in terms of the structural features of the two studied minerals. The larger channels of the sepiolite allow for a better insertion of the n-alkanes (longer retention times) while excluding the bulkier probes, such as cyclooctane or 2,2,4-trimethylpentane. Accordingly, the corresponding γ_s^d values were larger and the IMχT values were lower (higher surface nanoroughness) for the sepiolites. Regarding Lewis acid–base properties, all the sample’s surfaces evidenced a very strong amphoteric character. The present results highlight the potential of the evaluated samples for, e.g., adsorption processes with volatile organic compounds or matrix–filler interactions regarding the production of composite structures with Lewis acid–base matrices.

Physicochemical Gas-Solid Sorption Properties of Geologic Materials Using Inverse Gas Chromatography

The goal of this study was to determine the physicochemical properties of a variety of geologic materials using inverse gas chromatography (IGC) by varying probe gas selection, temperature, carrier gas flow rate, and humidity. This is accomplished by measuring the level of interaction between the materials of interest and known probe gases. Identifying a material's physicochemical characteristics can help provide a better understanding of the transport of gaseous compounds in different geologic materials or between different geological layers under various conditions. Our research focused on measuring the enthalpy (heat) of adsorption, Henry's constant, and diffusion coefficients of a suite of geologic materials, including two soil types (sandy clay-loam and loam), quartz sand, salt, and bentonite clay, with various particle sizes. The reproducibility of IGC measurements for geologic materials, which are inherently heterogeneous, was also assessed in comparison to the reproducibility for more homogeneous synthetic materials. This involved determining the variability of physicochemical measurements obtained from different IGC approaches, instruments, and researchers. For the investigated IGC-determined parameters, the need for standardization became apparent, including the need for application-relevant reference materials. The inherent physical and chemical heterogeneities of soil and many geologic materials can make the prediction of sorption properties difficult. Characterizing the properties of individual organic and inorganic components can help elucidate the primary factors influencing sorption interactions in more complex mixtures. This research examined the capabilities and potential challenges of characterizing the gas sorption properties of geologic materials using IGC.

A Co-Processed API Approach for a Shear Sensitive Compound Affording Improved Chemical Stability and Streamlined Drug Product Processing

The physical properties of active pharmaceutical ingredients (API) are critical to both drug substance (DS) isolation and drying operations, as well as streamlined drug product (DP) processing and the quality of final dosage units. High aspect ratio, low bulk density, API 'needles' in particular are a hindrance to efficient processing, with a low probability that conventional crystallization routes can modify the challenging morphology. The compound evaluated in this manuscript demonstrated this non-ideal morphology, with the added complexity of shear sensitivity. Modest shear exposure resulted in conversion of the thermodynamically stable crystalline phase to the amorphous phase, with the amorphous phase then undergoing accelerated chemical degradation. Slow filtration during DS isolation resulted in uncontrolled and elevated amorphous levels, while subsequent DP operations including blending, densification and compression increased amorphous content still further. A chemically stable final dosage unit would ideally involve a high bulk density, free flowing API that did not require densification in order to be commercialized as an oral dosage form with direct encapsulation of a single dosage unit. Despite every effort to modify the crystallization process, the physical properties of the API could not be improved. Here, an innovative isolation strategy using a thin film evaporation (TFE) process in the presence of a water soluble polymer alleviated filtration and drying risks and consistently achieved a high bulk density, free flowing co-processed API amenable to direct encapsulation. Characterization of the engineered materials suggested the lower amorphous levels and reduced shear sensitivity were achieved by coating surfaces of the API at relatively low polymer loads. This particle engineering route blurred conventional DS/DP boundaries that not only achieved improved chemical stability but also resulted in a optimized material, with simplified and more robust processing operations for both drug substance and drug product.

Thermoplastic bio-nanocomposites: From measurement of fundamental properties to practical application

Although the discovery of plastic has revolutionized materials used in many industries and by consumers, their non-biodegradable nature has led to one of the greatest problems of our times: plastic waste in the environment. Bioplastics which are biobased and biodegradable, have been suggested as alternatives for their fossil based counterparts, but their properties often do not meet the requirements that standard plastics would, and are in clear need of improvement. One way to do so is by the addition of nanoparticles which, when homogeneously dispersed, have been reported to result in great improvements. However, in practice, homogenous distribution of nanoparticles is not that trivial due to their tendency to aggregate, also after addition to the polymer matrix. Although theoretical frameworks to prevent this process are available, we feel that the options explored in practice are often rather trial and error in nature. For that reason, we review the theories available, aiming to facilitate the design of the nanocomposites for a sustainable future. We first discuss thermodynamic frameworks which revolve around nanoparticle aggregation. To minimize nanoparticle aggregation, the nanoparticle and polymer can be selected in such a way that they have similar polar and dispersive surface energies. The second part is dedicated to nanocomposite processing, where kinetic effects act on the nanocomposite material therewith influencing its final morphology, although it is good to point out that other factors such as reaggregation also affect the final nanocomposite morphology. The third section is dedicated to how nanoparticles affect the polymer matrix to which they are added. We describe how interactions at an atomic scale, result in the formation of an interphasial region which ultimately leads to changed bulk material properties. From these three sections, we conclude that three parameters are often overlooked when designing nanocomposites, namely the surface energies of the nanoparticles and polymers, the aggregation bond energy or strength, and the interphase region. Therefore, in the fourth section we provide an overview of techniques to identify these three parameters. We finish with a summery and outlook for the design of bio nanocomposites, where we bring all insights from the previous four sections together.

Interphases, Interfaces, and Surfaces of Active Materials in Rechargeable Batteries and Perovskite Solar Cells

The ever-increasing demand for clean sustainable energy has driven tremendous worldwide investment in the design and exploration of new active materials for energy conversion and energy-storage devices. Tailoring the surfaces of and interfaces between different materials is one of the surest and best studied paths to enable high-energy-density batteries and high-efficiency solar cells. Metal-halide perovskite solar cells (PSCs) are one of the most promising photovoltaic materials due to their unprecedented development, with their record power conversion efficiency (PCE) rocketing beyond 25% in less than 10 years. Such progress is achieved largely through the control of crystallinity and surface/interface defects. Rechargeable batteries (RBs) reversibly convert electrical and chemical potential energy through redox reactions at the interfaces between the electrodes and electrolyte. The (electro)chemical and optoelectronic compatibility between active components are essential design considerations to optimize power conversion and energy storage performance. A focused discussion and critical analysis on the formation and functions of the interfaces and interphases of the active materials in these devices is provided, and prospective strategies used to overcome current challenges are described. These strategies revolve around manipulating the chemical compositions, defects, stability, and passivation of the various interfaces of RBs and PSCs.

Determination of physicochemical properties of ionic liquids by gas chromatography

Over the years room temperature ionic liquids have gained attention as solvents with favorable environmental and technical features. Both chromatographic and conventional methods afford suitable tools for the study of their physicochemical properties. Use of gas chromatography compared to conventional methods for the measurement of physicochemical properties of ionic liquids have several advantages; very low sample concentrations, high accuracy, faster measurements, use of wider temperature range and the possibility to determine physicochemical properties of impure samples. Also, general purpose gas chromatography instruments are widely available in most laboratories thus alleviating the need to purchase more specific instruments for less common physiochemical measurements. Some of the main types of physicochemical properties of ionic liquids accessible using gas chromatography include gas-liquid partition constants, infinite dilution activity coefficients, partial molar quantities, solubility parameters, system constants of the solvation parameter model, thermal stability, transport properties, and catalytic and other surface properties.

Understanding Crystal Cleavability and Physical Properties of Crystal Surfaces Using in Silico Simulation

In the drug formulation process, compound dissolution rate and wettability may be improved by grinding. However, there is no method to understand the effects of the wettability of the crystal facets of the ground product. Here, acetylsalicylic acid (ASA) was used to evaluate the changes in crystal morphology and dissolution rate by jet milling using powder X-ray diffraction and in silico simulation. Several cleavage facets were observed in cube crystals, and the (0 0 2) facet was observed in plate crystals. Furthermore, the dissolution rate of the ground samples per unit area decreased with the cleavage of the (1 0 0) and (0 0 2) facets. The polar surface energy of the ground sample decreased with increasing grinding pressure. The simulation results showed that the absolute attachment energy of the (1 0 0) and (0 0 2) facets was lower than that of the other crystal facets. Moreover, atoms with low polarity were present on the crystal surface of (0 0 2). The wettability and dissolution rate of the (0 0 2) facet were worse than those of the (1 0 0) facet. It was suggested that the dissolution rate of the ground sample was affected by the wettability of the crystal facet caused by the cleavage. The cleavability and wettability may be understood by simulation.

Like dissolves like: A first-principles theory for predicting liquid miscibility and mixture dielectric constant

Liquid mixtures are ubiquitous. Miscibility and dielectric constant are fundamental properties that govern the applications of liquid mixtures. However, despite their importance, miscibility is usually predicted qualitatively based on the vaguely defined polarity of the liquids, and the dielectric constant of the mixture is modeled by introducing mixing rules. Here, we develop a first-principles theory for polar liquid mixtures using a statistical field approach, without resorting to mixing rules. With this theory, we obtain simple expressions for the mixture's dielectric constant and free energy of mixing. The dielectric constant predicted by this theory agrees well with measured data for simple binary mixtures. On the basis of the derived free energy of mixing, we can construct a miscibility map in the parameter space of the dielectric constant and molar volume for each liquid. The predicted miscibility shows remarkable agreement with known data, thus providing a quantitative basis for the empirical "like-dissolves-like" rule.