Cyclic loading of fractured cadaveric femurs after elastomer femoroplasty: an in vitro biomechanical study

Comparative biomechanical analysis of reconstruction and cephalomedullary nails in the treatment of osteoporotic subtrochanteric fractures

INTRODUCTION

This study aimed to compare the biomechanical properties of two types of intramedullary nails - reconstruction nails (RCN) and cephalomedullary nails (CMN) - each with different proximal fixations, in a model of an osteoporotic subtrochanteric femoral fracture. This study focused on assessing stiffness and load to failure of RCN and CMN nails to provide insight into their clinical applications in osteoporotic fracture treatments.

MATERIALS AND METHODS

Ten synthetic osteoporotic femoral models were used to generate a comminuted subtrochanteric fracture model. Five femurs were fixed using an RCN, and the remaining five were fixed using a CMN. The constructs were subjected to axial compression to measure their structural stiffness, load to failure, and failure modes.

RESULTS

The CMN group demonstrated a slightly higher load to failure (mean, 2250 N) than the RCN group (mean, 2100 N), which was statistically significant (p = 0.008). However, the stiffness in both groups was statistically similar (RCN, 250 N/mm; CMN, 255 N/mm; p = 0.69). Both groups showed a load to failure exceeding 1500 N, a typically exerted load on the femoral head by a 75 kg individual. The failure patterns differed, with CMN failures starting at the nail insertion area and RCN failures starting at the reconstruction screw area.

CONCLUSION

The RCN offers stiffness comparable to that of the CMN; although its load to failure is slightly lower than that of the CMN, it still exceeds the physiological tolerance limit. These findings suggest that the RCN is a viable alternative for treating osteoporotic subtrochanteric fractures.

Discrete particle model for cement infiltration within open-cell structures: Prevention of osteoporotic fracture

This paper proposes a discrete particle model based on the random-walk theory for simulating cement infiltration within open-cell structures to prevent osteoporotic proximal femur fractures. Model parameters consider the cement viscosity (high and low) and the desired direction of injection (vertical and diagonal). In vitro and in silico characterizations of augmented open-cell structures validated the computational model and quantified the improved mechanical properties (Young's modulus) of the augmented specimens. The cement injection pattern was successfully predicted in all the simulated cases. All the augmented specimens exhibited enhanced mechanical properties computationally and experimentally (maximum improvements of 237.95 ± 12.91% and 246.85 ± 35.57%, respectively). The open-cell structures with high porosity fraction showed a considerable increase in mechanical properties. Cement augmentation in low porosity fraction specimens resulted in a lesser increase in mechanical properties. The results suggest that the proposed discrete particle model is adequate for use as a femoroplasty planning framework.

Reusing cadaveric humeri for fracture testing after testing simulated rotator cuff tendon repairs

The financial cost of using human tissues in biomedical testing and surgical reconstruction is predicted to increase at a rate that is disproportionately greater than other materials used in biomechanical testing. Our first hypothesis is that cadaveric proximal humeri that had undergone monotonic failure testing of simulated rotator cuff repairs would not differ in ultimate fracture loads or in energy absorbed to fracture when compared to controls (i.e., bones without cuff repairs). Our second hypothesis is that there can be substantial cost savings if these cadaveric proximal humeri, with simulated cuff repairs, can be re-used for fracture testing. Results of fracture tests (conducted in a backwards fall configuration) and cost analysis support both hypotheses. Hence, the bones that had undergone monotonic failure tests of various rotator cuff repair techniques can be re-used in fracture tests because their load-carrying capacity is not significantly reduced.

Feasibility of osteosynthesis of fractured cadaveric hips following preventive elastomer femoroplasty

BACKGROUND

In vitro cadaveric studies showed that elastomer femoroplasty prevents displacement of fracture parts after proximal hip fracture allowing for conservative treatment. In the event that secondary displacement does occur, the purpose of this present study was to determine the feasibility of performing osteosynthesis of a fractured hip after preventive treatment with elastomer femoroplasty.

METHODS

Ten pairs of human cadaveric femurs were fractured in a simulated fall configuration. From each pair, one femur was randomly selected for elastomer femoroplasty prior to fracture generation and the contralateral femur was used as control. Following hip fracture generation, osteosynthesis was performed in all femurs. The operative time per case, technical difficulties during the procedure, and postoperative energy-to-failure load were recorded.

RESULTS

The mean (SD) time to perform osteosynthesis was 20 (6) minutes in the control-group and 19 (5) minutes in the elastomer femoroplasty-group (P=0.69). During osteosynthesis of the fractured hip in the elastomer femoroplasty-group, no difficulties including the need for additional instruments to remove elastomer from the proximal femur were recorded. Postoperative energy-to-failure load was similar in the control-group and the elastomer femoroplasty-group.

CONCLUSION

Fixation with routine osteosynthesis of displaced cadaveric hip fractures is not hindered by the presence of previously injected elastomer.