Does navigated patellar resurfacing in total knee arthroplasty result in proper bone cut, motion and clinical outcomes?

Individualised compared to off-the-shelf total knee arthroplasty results in lower and less variable patellar tilt

PURPOSE

The purpose of this study was to compare postoperative patellar tilt at 4 months follow-up in a consecutive series of randomised patients that received individualised or off-the-shelf (OTS) primary total knee arthroplasty (TKA). The hypothesis was that patellar tilt would be lower and less variable in patients who received individualised TKA compared to patients who received OTS TKA.

METHODS

A consecutive series of 385 patients randomised (1:1) to receive either OTS TKA or individualised TKA were analysed. Pre- and postoperative radiographs at 4 months were obtained of weight-bearing long leg, anterior-posterior and lateral knee views and a skyline view at 30° of flexion. Postoperative patellar tilt was measured between the anterior femoral line and patellar resection surface (β) and the anterior femoral line and mediolateral patellar axis (σ). Postoperative patellar tilt (absolute value) was compared between the individualised and OTS TKA groups based on preoperative phenotypes of their femoral mechanical angle, tibial mechanical angle and hip-knee-ankle angle. Variability in postoperative patellar tilt was compared using the 95% confidence intervals (CIs).

RESULTS

Comparisons of baseline patient characteristics revealed no difference between the individualised and OTS TKA groups. Comparison of absolute postoperative patellar tilt revealed significant differences between individualised and OTS TKA (|β|, 1.0° ± 1.0° and 2.5° ± 2.2°, respectively, p < 0.001; |σ|, 1.7° ± 1.6° and 2.8° ± 2.3°, respectively, p < 0.001). The 95% CI of postoperative patellar tilt (|β|) was narrower in patients that received individualised compared to OTS TKA (0.0° to 3.8° and 0.1° to 8.3°, respectively), irrespective of their preoperative phenotype.

CONCLUSION

Patients who underwent individualised TKA had lower and less variable postoperative patellar tilt than those with OTS TKA, irrespective of preoperative phenotype. Individualised TKA allows the decoupling of the tibiofemoral and patellofemoral joints, replicating anatomical trochlear orientation and improving patellar tilt, which could facilitate better clinical outcomes.

CLINICAL TRIAL REGISTRATION

This study constitutes a part of a larger registered randomised controlled trial comparing patient satisfaction following OTS versus individualised TKA (NCT04460989).

LEVEL OF EVIDENCE

Level II.

Isolated effects of patellar resurfacing in total knee arthroplasty and their relation to native patellar geometry

The isolated effects of patellar resurfacing on patellar kinematics are rarely investigated. Nonetheless, knowing more about these effects could help to enhance present understanding of the emergence of kinematic improvements or deteriorations associated with patellar resurfacing. The aim of this study was to isolate the effects of patellar resurfacing from a multi-stage in vitro study, where kinematics after total knee arthroplasty before and after patellar resurfacing were recorded. Additionally, the influence of the native patellar geometry on these effects was analysed. Eight fresh frozen specimens were tested successively with different implant configurations on an already established weight bearing knee rig. The patello-femoral kinematics were thereby measured using an ultrasonic measurement system and its relation to the native patellar geometries was analysed. After patellar resurfacing, the specimen showed a significantly medialized patellar shift. This medialization of the patellar tracking was significantly correlated to the lateral facet angle of the native patella. The patellar shift after patellar resurfacing is highly influenced by the position of the patellar button and the native lateral patellar facet angle. As a result, the ideal medio-lateral position of the patellar component is affected by the geometry of the native patella.

Musculoskeletal Multibody Simulation Analysis on the Impact of Patellar Component Design and Positioning on Joint Dynamics after Unconstrained Total Knee Arthroplasty

Patellofemoral (PF) disorders are considered a major clinical complication after total knee replacement (TKR). Malpositioning and design of the patellar component impacts knee joint dynamics, implant fixation and wear propagation. However, only a limited number of studies have addressed the biomechanical impact of the patellar component on PF dynamics and their results have been discussed controversially. To address these issues, we implemented a musculoskeletal multibody simulation (MMBS) study for the systematical analysis of the patellar component’s thickness and positioning on PF contact forces and kinematics during dynamic squat motion with virtually implanted unconstrained cruciate-retaining (CR)-TKR. The patellar button thickness clearly increased the contact forces in the PF joint (up to 27%). Similarly, the PF contact forces were affected by superior–inferior positioning (up to 16%) and mediolateral positioning (up to 8%) of the patellar button. PF kinematics was mostly affected by the mediolateral positioning and the thickness of the patellar component. A medialization of 3 mm caused a lateral patellar shift by up to 2.7 mm and lateral patellar tilt by up to 1.6°. However, deviations in the rotational positioning of the patellar button had minor effects on PF dynamics. Aiming at an optimal intraoperative patellar component alignment, the orthopedic surgeon should pay close attention to the patellar component thickness in combination with its mediolateral and superior–inferior positioning on the retropatellar surface. Our generated MMBS model provides systematic and reproducible insight into the effects of patellar component positioning and design on PF dynamics and has the potential to serve as a preoperative analysis tool.