The influence of graphite particle size on the synthesis of graphene-based materials and their adsorption capacity

Synthesis and Characterization of Graphite Intercalation Compounds with Sulfuric Acid

In this work, graphite intercalation compounds (GICs) were synthesized using three different oxidizers: (NH4)2S2O8, K2S2O8, and CrO3 with and without P2O5 as a water-binding agent. Furthermore, the samples obtained were heat-treated at 800 °C. Specimens were characterized by optical microscopy, Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), and scanning electron microscopy (SEM). The correlation between different characteristic parameters of the Raman analysis has shown that the use of CrO3 results in a much higher structural disorder compared to the products obtained using persulfate oxidizers. Narrowing the correlation set revealed that minimal defect concentration can be reached by using K2S2O8, while the use of (NH4)2S2O8 causes a slightly higher concentration of defects. It was also established that the additional use of P2O5 can help to achieve more effective intercalation and has a positive effect on the formation of the stage I GIC phase. After heat treatment, the intercalated products mostly return to a graphite-like structure; however, the samples obtained with CrO3 stand out with the most significant changes in their surface morphology. Therefore, analysis suggests that GICs obtained using persulfate oxidizers and P2O5 could be a candidate to produce high-quality graphene or graphene oxide.

The Differences of Graphene Oxide Products Made from Three Kinds of Flake Graphites

Graphene oxide (GO), a widespread load platform in many research studies based on its microstructures, is largely made from flake graphite by a strong oxidation method. However, the differences of GO products made from different flake graphites have received little attention. Here, five GO products made from five different flake graphites by the Hummers method are investigated. The results reveal the differences in microstructures of the five GOs concerned with the ratio of C-C sp² structures to defects and the amount of oxygen-containing functional groups, which are further evidenced by their performances of quenching efficiencies by five DNA fluorescent probes. We demonstrated that the microstructural differences of GO products are transmitted from their parent flake graphites. Meanwhile, three kinds of parent flake graphites are proposed: (1) with large flakes and complete C-C sp² structures, (2) with large flakes but defective C-C sp² structures, and (3) with fine flakes but moderate C-C sp² structures, in which the performance of GO made from (1) is the best while the GO made from (3) shows comparable to or even better performance than that made from (2). Our work gives a reminder for precisely choosing graphite in the preparation of GOs and the potential value of tremendous natural fine-flake graphites.

Tailorable Synthesis of Highly Oxidized Graphene Oxides via an Environmentally-Friendly Electrochemical Process

Graphene oxide (GO) is an attractive alternative to graphene for many applications due to its captivating optical, chemical, and electrical characteristics. In this work, GO powders with a different amount of surface groups were synthesized from graphite via an electrochemical two-stage process. Many synthesis conditions were tried to maximize the oxidation level, and comprehensive characterization of the resulting samples was carried out via elemental analysis, microscopies (TEM, SEM, AFM), X-ray diffraction, FT-IR and Raman spectroscopies as well as electrical resistance measurements. SEM and TEM images corroborate that the electrochemical process used herein preserves the integrity of the graphene flakes, enabling to obtain large, uniform and well exfoliated GO sheets. The GOs display a wide range of C/O ratios, determined by the voltage and time of each stage as well as the electrolyte concentration, and an unprecedented minimum C/O value was obtained for the optimal conditions. FT-IR evidences strong intermolecular interactions between neighbouring oxygenated groups. The intensity ratio of D/G bands in the Raman spectra is high for samples prepared using concentrated H2SO4 as an electrolyte, indicative of many defects. Furthermore, these GOs exhibit smaller interlayer spacing than that expected according to their oxygen content, which suggests predominant oxidation on the flake edges. Results point out that the electrical resistance is conditioned mostly by the interlayer distance and not simply by the C/O ratio. The tuning of the oxidation level is useful for the design of GOs with tailorable structural, electrical, optical, mechanical, and thermal properties.