A novel water-in-ionic liquid microemulsion and its interfacial effect on the activity of laccase

Dielectric Depiction of 1-Butyl-3-methylimidazolium Tetrafluoroborate/1-Butyl-3-methylimidazolium 1,4-Bis(2-ethylhexyl) Sulfosuccinate/Benzene Microemulsions: Percolation, Interface Polarization, and Electrical Parameters

Two dielectric relaxations located at approximately 10 and 300 MHz were analyzed in the microemulsion composed of the polar ionic liquid (PIL) 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4]), the surface-active ionic liquid (SAIL) 1-butyl-3-methylimidazolium 1,4-bis(2-ethylhexyl) sulfosuccinate ([bmim][AOT]), and benzene. The curve of the dc conductivity vs PIL weight fraction shows two inflection points, namely, 16.69 and 27.90 wt %, which are used to divide the PIL/O, bicontinuous (B.C.), and O/PIL subregions. The critical exponents of percolation u = 0.75, 0.79, and 0.80 are suggested from the scaling dependence of dc conductivity on the PIL weight fraction, together with frequency dependences of both permittivity and loss angle, which all infer that static percolation occurs in the microemulsion. Only one dielectric relaxation at high frequency was observed in the PIL/O subregion, when the concentration increased to the boundary between the PIL/O and B.C. subregions; the second dielectric relaxation appeared at low frequency. The high-frequency relaxation is caused by interfacial polarization. The low-frequency relaxation is attributed to the dipole-oriented polarization of AOT-. When the oil content of the system was reduced, the interface became softer to allow more AOT- to rotate, and the cation shifted from moving around its long axis to rotating along its short axis. The static dielectric constant of [bmim][AOT] was given. The dielectric constants and conductivity of the dispersed and continuous phases in the PIL/O and O/PIL subregions were calculated from the dielectric parameters of high-frequency relaxation.

Water-pluronic-ionic liquid based microemulsions: Preparation, characterization and application as micro-reactor for enhanced catalytic activity of Cytochrome-c

Microemulsions (µEs), comprising water as polar component, pluronic (normal, L35 and reverse, 10R5) as surfactant and a hydrophobic ionic liquid (HIL) as non-polar component have been prepared and characterized. Owing to higher surface activity, pluronics have promoted the formation of µEs without the use of co-surfactant. Thus prepared µEs have been utilized as nano-reactors for the oxidation of guaiacol in the presence of Cytochrome-c (Cyt-c) at 15, 20, and 25 °C. A 3.2- and 1.3-fold increase in the rate of formation of product of enzymatic catalysis in direct µE (HIL-in-water) with reverse pluronic (10R5) is observed at 15 and 20 °C as compared to that in buffer. However, negligible enzymatic activity is observed in the direct µE formed by normal pluronic (L35). The catalytic activity of Cyt-c decreases in reverse µEs (water-in-HIL) as compared to direct µEs irrespective of the nature of pluronic used. The contrasting nature of nano-interfaces formed by pluronics in µEs and the extent of hydration of these nano-interfaces controlled by temperature exerts varying influence on the catalytic activity of Cyt-c. It is expected that the present work would result in providing a versatile platform for the creation of new IL and pluronic-based µEs for bio-catalytic applications, which have never been reported.

Electropolymerization of EDOT in an anionic surfactant-stabilized hydrophobic ionic liquid-based microemulsion

Here, an anionic surfactant [AOT]^- (bis-(2-ethylhexyl) sulfosuccinate)-stabilized H₂O/[Omim][PF₆] (1-octyl-3-methylimidazolium hexafluorophosphate) microemulsion has been tested for the first time as a medium for the electropolymerization of 3,4-ethylenedioxythiophene (EDOT). To formulate AOT-stabilized [Omim][PF₆]-based microemulsions of different water contents, the phase triangle was determined at 35 °C. Measurements of the conductivities of the microemulsions, their solubilization capacities toward EDOT and their catalytic effects on EDOT electrooxidation show that the present [AOT]^--stabilized ionic liquid microemulsion is a good medium for EDOT electropolymerization. Studies on the process of the electropolymerization of EDOT in this [Omim][PF₆]-based microemulsion indicate that the water content (i.e., microstructure) of the microemulsion medium is an important factor affecting the onset potential and the deposition rate of the PEDOT. The morphology and the doping level of the as-prepared PEDOT are also found to be correlated with the water content of the ionic liquid microemulsion. The microemulsion with higher water content results in a PEDOT with better electroactivity and higher doping levels. FTIR spectra and XPS analysis show that the PEDOT electrosynthesized in the microemulsion is co-doped by both [AOT]^- and [PF₆]^-. Compared with the neat [Omim][PF₆], the use of the ionic liquid microemulsions can reduce not only the consumption of the expensive ionic liquid, but also the onset potential for the electrooxidation of EDOT. Moreover, by tuning the water content of the medium, the electropolymerization of PEDOT and its electrochemical properties could be regulated accordingly. Under the identical deposited charge, the PEDOT originated from the high water content microemulsion (50% H₂O μE) has a higher specific capacitance (124 F g^-1) than that from neat [Omim][PF₆] (117 F g^-1). It follows that the present ionic liquid microemulsion is a good medium for EDOT electropolymerization. The present study opens up a new route for the green and low-cost electrochemical preparation of high-performance PEDOT.

Mixed micelles and bicontinuous microemulsions: Promising media for enzymatic reactions

Enzymes, the natural catalysts, replace catalysts of chemical origin in a wide spectrum of reactions and generally work under environment friendly conditions. Various strategies are adopted to modify catalytic activities of enzymes further, of which one is application of novel reaction medium. This work reviews applicability of novel media like mixed micelles and bicontinuous microemulsions in enzymatic reactions and points out their capability to play bigger roles in enzyme catalysis. Ionic reverse micelles reduced catalytic activities of enzymes through denaturation. Addition of nonionic surfactant to these reverse micelles led to corresponding mixed micelles and thus restored or sometimes enhanced catalytic abilities of enzymes. Mixed micelles comprising of two nonionic surfactants, bicontinuous microemulsion containing two anionic surfactants also acted as efficient reaction media for enzymes. Even a cationic/anionic/nonionic mixed micelle was found to increase activity of enzyme. Mixed micelles and bicontinuous microemulsions comprising of anionic and zwitterionic surfactants augmented enzyme catalysis. Mixed micelles and bicontinuous microemulsions containing ionic liquid and surfactant also had critical impact on enzyme catalysis. Catalytic abilities of enzymes altered significantly in substrate/surfactant and bile salt/surfactant mixed micelles. Concentrations of individual surfactant, molar ratio of surfactants, and molar ratio of water to total surfactants had notable impacts on enzyme catalysis in those media.

Biocompatible Solvents and Ionic Liquid-Based Surfactants as Sustainable Components to Formulate Environmentally Friendly Organized Systems

In this review, we deal with the formation and application of biocompatible water-in-oil microemulsions commonly known as reverse micelles (RMs). These RMs are extremely important to facilitate the dissolution of hydrophilic and hydrophobic compounds for biocompatibility in applications in drug delivery, food science, and nanomedicine. The combination of two wisely chosen types of compounds such as biocompatible non-polar solvents and ionic liquids (ILs) with amphiphilic character (surface-active ionic liquids, SAILs) can be used to generate organized systems that perfectly align with the Green Chemistry concepts. Thus, we describe the current state of SAILs (protic and aprotic) to prepare RMs using non-polar but safe solvents such as esters derived from fatty acids, among others. Moreover, the use of the biocompatible solvents as the external phase in RMs and microemulsions/nanoemulsions with the other commonly used biocompatible surfactants is detailed showing the diversity of preparations and important applications. As shown by multiple examples, the properties of the RMs can be modified by changes in the type of surfactant and/or external solvents but a key fact to note is that all these modifications generate novel systems with dissimilar properties. These interesting properties cannot be anticipated or extrapolated, and deep analysis is always required. Finally, the works presented provide valuable information about the use of biocompatible RMs, making them a green and promising alternative toward efficient and sustainable chemistry.

Biamphiphilic ionic liquid based aqueous microemulsions as an efficient catalytic medium for cytochrome c

Considering the remarkable applicability of ionic liquids (ILs) in bio-catalysis involving enzymes, herein, we report new IL based aqueous microemulsions as a catalytic reactor for cytochrome c (Cyt-c). Microemulsions (μEs), comprising water as the polar component, imidazolium (cation) and dioctylsulfosuccinate (AOT) (anion) based biamphiphilic ionic liquid (BAIL) as the surfactant and a hydrophobic ionic liquid (HIL) as the non-polar component have been prepared and characterized. The use of BAIL has promoted the formation of μEs without any co-surfactant, owing to its higher surface activity. The effect of ester- or amide-functionalization of the alkyl chain of the imidazolium cation of BAILs on the phase behavior of μEs has been investigated. The prepared μEs have been characterized via conductivity, dynamic light scattering (DLS), UV-vis absorption and steady-state fluorescence (using external polarity probes) techniques. The prepared μEs have been employed as nano-reactors for exploring the catalytic activity of Cyt-c. The formed BAIL-water nano-interfaces in reverse μEs have exerted a positive effect on the catalytic activity of Cyt-c stored in a water pool of reverse μEs. A five-fold higher rate constant in μEs as compared to buffer establishes μEs as a better catalytic medium. Furthermore, the differing nature of nano-interfaces created by BAILs and water in reverse μEs, depending on the functionalization of the alkyl chain of the cationic part of BAIL, has exerted varying influence on the catalytic activity of Cyt-c. It is expected that the present work will result in providing a versatile platform for the creation of new IL and water based μEs for bio-catalytic applications.

Proteins in Ionic Liquids: Reactions, Applications, and Futures

Biopolymer processing and handling is greatly facilitated by the use of ionic liquids, given the increased solubility, and in some cases, structural stability imparted to these molecules. Focussing on proteins, we highlight here not just the key drivers behind protein-ionic liquid interactions that facilitate these functionalities, but address relevant current and potential applications of protein-ionic liquid interactions, including areas of future interest.

Fatty acids-based microemulsion liquid chromatographic determination of multiple caffeoylquinic acid isomers and caffeic acid in honeysuckle sample

A green and efficient microemulsion liquid chromatographic (MELC) method using fatty acid as co-surfactant and electrochemical detection was established and validated for the determination of four caffeoylquinic acid isomers and caffeic acid in honeysuckle samples. The influences of each individual component within the isocratic oil-in-water (O/W) microemulsion mobile phase were systematically investigated, such as the type and concentration of co-surfactant, concentration of sodium dodecyl sulphate (SDS), organic modifier addition, type and concentration of oil phase, pH and detection voltage. Results indicated that excellent resolution was achieved using 3.0% w/v of propionic acid, 0.5% w/v of ethyl acetate, 1.0% w/v of SDS, 5% w/v acetonitrile, 90.5% v/v of water and 25 mM sodium dihydrogen phosphate at pH = 3 as microemulsion mobile phase and 0.8 V as the optimal voltage value. Under the optimal condition, analytical performance of developed method was evaluated. The detection limits were below 17.3 ng/mL and intra-day and inter-day precisions by relative standard deviations (RSD%) were between 0.5% and 3.6%. Satisfactory recovery (in the range of 83.8-109.1%) with good repeatability lower than 4.7% (n = 3) was obtained. Therefore, the developed O/W MELC method was rapid, precise and accurate for simultaneous determination of neochlorogenic acid, chlorogenic acid, isochlorogenic acid A and isochlorogenic acid C in honeysuckle samples, with contents of 2.6, 28.7, 18.1 and 5.2 mg/g, respectively.

Small-angle X-ray scattering study on nano-scale structures controlled by water content in a binary water/ionic liquid system

We report the water-in-ionic-liquid microemulsions (ME) formed in a binary water/ionic liquid system, without organic solvents, using a surfactant ionic liquid (SAIL) based on 1-butyl-3-methylimidazolium (C4mIm+) as the cation and dioctyl sulfosuccinate (AOT-) as the anion. Small-angle X-ray scattering (SAXS) revealed that MEs were stably formed in the binary water/SAIL solutions in the low water content region (water volume fraction, φw < 0.1), and the ME size systematically increased with increasing φw. We further investigated the nanostructures of the high φw region using a combination of SAXS and rheological measurements and found that the MEs changed to a stacked lamellar structure comprising SAIL bilayers and water phases at φw > 0.12. At the largest water content, φw = 0.99, vesicle structures were obtained.

"Solvent-in-salt" systems for design of new materials in chemistry, biology and energy research

Inorganic and organic "solvent-in-salt" (SIS) systems have been known for decades but have attracted significant attention only recently. Molten salt hydrates/solvates have been successfully employed as non-flammable, benign electrolytes in rechargeable lithium-ion batteries leading to a revolution in battery development and design. SIS with organic components (for example, ionic liquids containing small amounts of water) demonstrate remarkable thermal stability and tunability, and present a class of admittedly safer electrolytes, in comparison with traditional organic solvents. Water molecules tend to form nano- and microstructures (droplets and channel networks) in ionic media impacting their heterogeneity. Such microscale domains can be employed as microreactors for chemical and enzymatic synthesis. In this review, we address known SIS systems and discuss their composition, structure, properties and dynamics. Special attention is paid to the current and potential applications of inorganic and organic SIS systems in energy research, chemistry and biochemistry. A separate section of this review is dedicated to experimental methods of SIS investigation, which is crucial for the development of this field.

Protein diffusion in a bicontinuous microemulsion: inducing sub-diffusion by tuning the water domain size

We study the diffusion of an enhanced green fluorescent protein (GFP+) in bicontinuous sugar-surfactant based microemulsions. The size of the water domains in such systems is controlled by changes of the oil-to-water ratio. Hence, microemulsions allow to produce confinement effects in a controlled way. At high water content the protein is found to exhibit Fickian diffusion. Decreasing the water domain size leads to a slowing down of the protein diffusion and sub-diffusive behavior is obtained on the scale observed by fluorescence correlation spectroscopy. Further decrease of the water domain size finally nearly fixes the GFP+ in these domains and forces it to increasingly follow the breathing mode of the microemulsion matrix.

Tailored ionic liquid-based surfactants for the formation of microemulsions with water and a hydrophobic ionic liquid

Microemulsions (μe) with water and a hydrophobic ionic liquid (IL) usually require 45-60 wt% surfactant to solubilize equal amounts of water and IL. To increase the efficiency we designed a new class of surfactants by combining a hydrophilic but IL-ophobic carbohydrate-based part with a hydrophobic but IL-ophilic IL-based part. These surfactants allow formulating microemulsions with 20 wt% surfactant only which opens up a new arena for efficient water-IL μes.

Study on the catalytic performance of laccase in the hydrophobic ionic liquid-based bicontinuous microemulsion stabilized by polyoxyethylene-type nonionic surfactants

To formulate a compatible green medium for the conversion of a hydrophobic substrate by a hydrophilic enzyme, we investigated the phase behavior of pseudo ternary hydrophobic ionic liquid (HIL)/buffer/polyoxyethylene-type nonionic surfactant (CnEm)/n-alcohol system and the effects of the components on the formulation of the HIL-based bicontinuous microemulsion. It is found that small head group of the surfactant, high concentration of n-alcohol (medium/long alkyl chain) and low cohesive energy density of the HIL result in low phase transition temperature. In the CnEm stabilized compatible bicontinuous microemulsion, the kinetics of laccase catalyzed oxidation of 2,6-dimethoxyphenol were also investigated. It is found that in addition to temperature, n-alcohol is the key parameter affecting the catalytic performance of laccase, and the optimum n-alcohol depends on the type of HIL as an oil phase. All the kinetic parameters, such as Km, kcat, kcat/Km, and Ea (apparent activation energy), indicate that the bicontinuous microemulsion consisting of [Omim]NTf2/buffer/CnEm/n-hexanol is a suitable medium for the laccase-catalyzed reaction. To the best of our knowledge, this is the first report on the formulation of HIL-based bicontinuous microemulsion for enzyme catalysis.

Transport properties of microemulsions with ionic liquid apolar domains as a function of ionic liquid content

The conductivity, dynamic viscosity and diffusion coefficient of aqueous ionic liquid microemulsions were measured as a function of ionic liquid content. ​The conclusions from transport properties were supported by UV-Vis as well as FTIR measurements.

Water-in-ionic liquid microemulsion formation in solvent mixture of aprotic and protic imidazolium-based ionic liquids

We report that water-in-ionic liquid microemulsions (MEs) are stably formed in an organic solvent-free system, i.e., a mixture of aprotic (aIL) and protic (pIL) imidazolium-based ionic liquids (ILs) containing the anionic surfactant dioctyl sulfosuccinate sodium salt (AOT). Structural investigations using dynamic light, small-angle X-ray, and small-angle neutron scatterings were performed for MEs formed in mixtures of aprotic 1-octyl-3-methylimidazolium ([C8mIm(+)]) and protic 1-alkylimidazolium ([CnImH(+)], n = 4 or 8) IL with a common anion, bis(trifluoromethanesulfonyl)amide ([TFSA(-)]). It was found that the ME structure strongly depends on the mixing composition of the aIL/pIL in the medium. The ME size appreciably increases with increasing pIL content in both [C8mIm(+)][TFSA(-)]/[C8ImH(+)][TFSA(-)] and [C8mIm(+)][TFSA(-)]/[C4ImH(+)][TFSA(-)] mixtures. The size is larger for the n = 8 system than that for the n = 4 system. These results indicate that the shell part of MEs is composed of both AOT and pIL cation, and the ME size can be tuned by pIL content in the aIL/pIL mixtures.

Amphiphile self-assemblies in supercritical CO2 and ionic liquids

Supercritical (sc) CO2 and ionic liquids (ILs) are very attractive green solvents with tunable properties. Using scCO2 and ILs as alternatives of conventional solvents (water and oil) for forming amphiphile self-assemblies has many advantages. For example, the properties and structures of the amphiphile self-assemblies in these solvents can be easily modulated by tuning the properties of solvents; scCO2 has excellent solvation power and mass-transfer characteristics; ILs can dissolve both organic and inorganic substances and their properties are designable to satisfy the requirements of various applications. Therefore, the amphiphile self-assemblies in scCO2 and ILs have attracted considerable attention in recent years. This review describes the advances of using scCO2 or/and ILs as amphiphile self-assembly media in the last decade. The amphiphile self-assemblies in scCO2 and ILs are first reviewed, followed by the discussion on combination of scCO2 and ILs in creating microemulsions or emulsions. Some future directions on the amphiphile self-assemblies in scCO2 and ILs are highlighted.

Esterification of oleic acid in [Bmim]BF4/[Hmim]HSO4 + TX-100/cyclohexane ionic liquid microemulsion

[Hmim]HSO₄-based microemulsion is an efficient catalyst system for esterification; it provides large interface areas, the resultant water enters [Bmim]BF₄ microdomain.

The Henry reaction in [Bmim][PF₆]-based microemulsions promoted by acylase

An environmentally-friendly, enzyme-promoted procedure for the Henry reaction was first studied using water-in-[Bmim][PF6] microemulsions as reaction medium. The Amano acylase from Aspergillus oryzae showed better catalytic activity for the addition reactions of nitromethane with a series of aromatic aldehydes, and a highest yield of 90% was obtained.

The catalytic activity enhancement and biodegradation potential of free laccase and novel sol-gel laccase in non-conventional solvents

The catalytic activity of free laccase and a novel sol-gel laccase (SOLAC) in ionic liquids and organic solvents was demonstrated by using 2,6-dimethoxyphenol (2,6-DMP) as a substrate. The enhancement of the catalytic activity of the SOLAC was observed and compared to the free laccase in both media. The oxidative biodegradation of o-chlorophenol as a model of phenolic environmental pollutants in organic media shows that the degradation was observed only when using water pre-saturated organic solvents or reverse micelle system. The SOLAC gave higher biodegradation rate in either aqueous or organic solvents, in which the optimum temperature was observed at 40 °C for the reverse micelle system as a reaction medium. All results demonstrated the potential use of the SOLAC for biodegradation of phenolic environmental pollutants in non-conventional media.