Pore formation in 1,2-dimyristoyl-sn-glycero-3-phosphocholine/cholesterol mixed bilayers by low concentrations of antimicrobial peptide melittin

Bioactive Glass and Melittin Thin Films Deposited by MAPLE for Titanium Implant Functionalization

The development of bioactive coatings for metallic implants is essential to enhance osseointegration and improve implant longevity. In this study, composite thin films based on bioactive glass and melittin were synthesized using the matrix-assisted pulsed laser evaporation technique and deposited onto titanium substrates. The coatings were characterized using physicochemical analysis methods, including scanning electron microscopy, atomic force microscopy, contact angle measurements, Fourier transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, and electrochemical impedance spectroscopy. Simulated body fluid immersion tests were also conducted to assess bioactivity over time. Scanning electron microscopy and atomic force microscopy revealed dense, irregular surface textures with nanoscale features and an average roughness of ~120 nm, favorable for cell adhesion. Contact angle measurements showed a significant shift from hydrophobic (~95° for bare titanium) to moderately hydrophilic (~62° for the bioglass and melittin coating) surfaces, indicating improved biocompatibility. Electrochemical impedance spectroscopy demonstrated enhanced corrosion resistance in simulated body fluid, with the coating exhibiting a ~45% decrease in impedance magnitude after 12 h of immersion, compared to only 4% for bare titanium. Fourier transform infrared spectroscopy and energy-dispersive X-ray spectroscopy analyses confirmed the progressive formation of a carbonated apatite layer after 7 days of simulated body fluid exposure, suggesting high bioactivity and osteoconductive potential. The combined effects of bioactive glass and melittin in the thin film structure offer promising applications in orthopedic and dental implants, enhancing both biological performance and structural integrity.

Neochloris oleoabundans cell wall rupture through melittin peptide: a new approach to increase lipid recovery

OBJECTIVES

Microalgae cell wall affects the recovery of lipids, representing one of the main difficulties in the development of biofuel production. This work aimed to test a new method based on melittin peptide to induce a cellular disruption in N. oleoabundans.

RESULTS

Neochloris oleoabundans cells were grown at 32 °C in the presence of a high concentration of nitrate-phosphate, causing a cell disruption extent of 83.6%. Further, a two-fold increase in lipid recovery following melittin treatment and solvent extraction was observed. Additionally, it was possible to verify the effects of melittin, both before and after treatment on the morphology of the cells. Scanning electron microscopy (SEM) and confocal images of the melittin-treated microalgae revealed extensive cell damage with degradation of the cell wall and release of intracellular material.

CONCLUSIONS

Melittin produced a selective cell wall rupture effect in N. oleoabundans under some culture conditions. These results represent the first report on the effect of melittin on lipid recovery from microalgae.

Structure, Function, and Physicochemical Properties of Pore-forming Antimicrobial Peptides

Antimicrobial peptides (AMPs), a class of antimicrobial agents, possess considerable potential to treat various microbial ailments. The broad range of activity and rare complete bacterial resistance to AMPs make them ideal candidates for commercial development. These peptides with widely varying compositions and sources share recurrent structural and functional features in mechanisms of action. Studying the mechanisms of AMP activity against bacteria may lead to the development of new antimicrobial agents that are more potent. Generally, AMPs are effective against bacteria by forming pores or disrupting membrane barriers. The important structural aspects of cytoplasmic membranes of pathogens and host cells will also be outlined to understand the selective antimicrobial actions. The antimicrobial activities of AMPs are related to multiple physicochemical properties, such as length, sequence, helicity, charge, hydrophobicity, amphipathicity, polar angle, and also self-association. These parameters are interrelated and need to be considered in combination. So, gathering the most relevant available information will help to design and choose the most effective AMPs.

Synergistic effect of ultrasound and antimicrobial solutions of cecropin P1 in the deactivation of Escherichia coli O157:H7 using a cylindrical ultrasonic system

This study investigates the synergistic effect of ultrasonication and antimicrobial action of antimicrobial peptide cecropin P1 on the inactivation of Escherichia coli O157:H7 in a cylindrical ultrasonication system. The inactivation of E. coli at pH 7.4 was performed using: ultrasonication (14, 22, and 47 kHz), cecropin P1 (20 µg/mL), and a combination of both. We found the treatment at 22 kHz, 8W for 15 min of exposure and a combination of ultrasound at higher frequency (47 kHz, 8 W) and cecropin P1 for one minute of exposure were more efficient, reducing the cell density by six orders of magnitude, compared to individual treatments (ultrasound or cecropin P1 only). Dye leakage studies and transmission electron microscopy further validated these results. A continuous flow system was designed to demonstrate synergism of ultrasonication with antimicrobial peptide Cecropin P1 in the inactivation of E. coli; synergism was shown to be more at higher ultrasonication frequencies and power levels. Acoustic cavitation by ultrasonic treatment could drastically improve microbial deactivation by antimicrobial peptides cecropin P1 by increasing their ability for pore formation in cell membranes. A continuous ultrasonication and antimicrobial peptides system can lead to an energy-efficient and economical sterilization system for food safety applications.

Development and Characterization of the Shortest Anti-Adhesion Peptide Analogue of B49Mod1

Inhibition of cancer cell adhesion is an effective approach to killing adherent cancer cells. B49 and its analog B49Mod1 peptides, derived from the extracellular domain (ECD) of bone marrow stromal antigen 2 (BST-2), display anti-adhesion activity on breast cancer cells. However, the minimal sequence required for this anti-adhesion activity is unknown. Here, we further characterized the anti-adhesion activity of B49Mod1. We show that the anti-adhesion activity of B49Mod1 may require cysteine-linked disulfide bond and that the peptide is susceptible to proteolytic deactivation. Using structure-activity relationship studies, we identified an 18-Mer sequence (B18) as the minimal peptide sequence mediating the anti-adhesion activity of B49Mod1. Atomistic molecular dynamic (MD) simulations reveal that B18 forms a stable complex with the ECD of BST-2 in aqueous solution. MD simulations further reveal that B18 may cause membrane defects that facilitates peptide translocation across the bilayer. Placement of four B18 chains as a transmembrane bundle results in water channel formation, indicating that B18 may impair membrane integrity and form pores. We hereby identify B18 as the minimal peptide sequence required for the anti-adhesion activity of B49Mod1 and provide atomistic insight into the interaction of B18 with BST-2 and the cell membrane.

Cholesterol re-organisation and lipid de-packing by arginine-rich cell penetrating peptides: Role in membrane translocation

Cell penetrating peptides (CPPs) are able to transport hydrophilic molecules inside cells. To reach the cytosol, the peptide associated with a cargo must cross the plasma or the endosomal membrane. Different molecular mechanisms for peptide internalisation into cells have been proposed and it is becoming clear that the cellular internalisation mechanisms are different depending on the peptide sequence and structure and the target membrane. Herein, the penetration of three peptides into large unilamellar vesicles were studied: the homeodomain derived 16-residues penetratin, nona-arginine (R9), and a small peptide containing 6 arginine and 3 tryptophan residues (RW9). The membrane models were composed of phospholipids from natural sources containing different molecular species. We observed that among the three peptides, only the amphipathic peptide RW9 was able to cross the membrane vesicles in the liquid disordered state. The changes in the distribution of the previously characterized cholesterol-pyrene probe show that cholesterol-pyrene molecules dissociate from clusters upon membrane interaction with the three peptides and that the cholesterol environment becomes more disordered in the presence of RW9. Finally, we studied the effect of the peptides on lipid ordering on giant plasma membrane vesicles. The amphipathic peptides RW9 and its longer homologue RW16 induced lipid de-packing in plasma membrane vesicles. Overall, the data suggest that a disordered membrane favours the translocation of RW9, that the membrane cholesterol is redistributed during peptide interaction, and that the peptide amphipathic character is important to increase membrane fluidity and peptide membrane translocation.

14-Helical β-Peptides Elicit Toxicity against C. albicans by Forming Pores in the Cell Membrane and Subsequently Disrupting Intracellular Organelles

Synthetic peptidomimetics of antimicrobial peptides (AMPs) are promising antimicrobial drug candidates because they promote membrane disruption and exhibit greater structural and proteolytic stability than natural AMPs. We previously reported selective antifungal 14-helical β-peptides, but the mechanism of antifungal toxicity of β-peptides remains unknown. To provide insight into the mechanism, we studied antifungal β-peptide binding to artificial membranes and living Candida albicans cells. We investigated the ability of β-peptides to interact with and permeate small unilamellar vesicle models of fungal membranes. The partition coefficient supported a pore-mediated mechanism characterized by the existence of a critical β-peptide concentration separating low- and high-partition coefficient regimes. Live cell intracellular tracking of β-peptides showed that β-peptides translocated into the cytoplasm, and then disrupted the nucleus and vacuole sequentially, leading to cell death. This understanding of the mechanisms of antifungal activity will facilitate design and development of peptidomimetic AMPs, including 14-helical β-peptides, for antifungal applications.

Small Synthetic Peptides Bioconjugated to Hybrid Gold Nanoparticles Destroy Potentially Deadly Bacteria at Submicromolar Concentrations

Synthetic antibacterial peptides are advanced weapons that scientists design and produce to confront current threats of harmful and mortal pathogens, which could affect humans in everyday life. Recently, many small amino acid sequences, greatly efficient in their antibacterial action, have been reported in the literature. To date, only a few synthetic peptides, acting at micromolar or even tenths of micromolar concentrations, are on the market as commercial products, mainly because of their high cost of production. In this context, materials science can provide fundamental help by engineering small synthetic peptides, powered by hybrid gold nanoparticles, which have been found to strongly enhance antimicrobial activity against bacterial infections. Submicromolar concentrations of the 1018K6 peptide, bioconjugated to hybrid polymer-gold nanoparticles, kill almost 100% of pathogen bacteria, such as Listeria and Salmonella genera, paving the way for economically sustainable commercial products based on this synthetic nanocomplex.

Nucleation and growth of pores in 1,2-Dimyristoyl-sn-glycero-3-phosphocholine (DMPC) / cholesterol bilayer by antimicrobial peptides melittin, its mutants and cecropin P1

Antimicrobial peptides are one of the most promising alternatives to antibiotics for targeting pathogens without developing resistance. In this study, pore formation in 1,2-Dimyristoyl-snglycero-3-phosphocholine (DMPC) / cholesterol liposome induced by native melittin, its two mutant variants (G1I and I17 K), and cecropin P1 was investigated by monitoring the dynamics of fluorescence dye leakage. A critical peptide concentration was required for dye leakage with the rate of leakage being dependent on peptide concentration above a critical value. A lag time was required for dye leakage for low peptide concentrations that are above the critical value, which decreased at higher peptide concentrations eventually approaching zero. Lag time was found to be in the order I17 K mutant with lower hydrophobicity and higher net charge > G1I with higher hydrophobicity > melittin > cecropin P1. Cecropin P1 exhibited the highest rate of dye leakage followed by melittin, G1I, and I17 K. Size distribution and transmission electron microscopy (TEM) of liposomes exposed to peptides of different concentrations indicated pore formation with accompanied stretching of liposomes at low peptide concentrations for both melittin and cecropin P1. At much higher concentrations, however, size distribution indicated three peaks for both peptides. In both cases, TEM images show that the middle and small peaks are shown to be due to stretched liposome and broken stretched liposome respectively. For melittin, the large peak is due to peptide aggregates as well as aggregates of liposome. For cecropin P1, however, the large peak indicates cecropin P1 aggregates with solubilized lipids thus suggesting carpet mechanism.

Potential of mean force for insertion of antimicrobial peptide melittin into a pore in mixed DOPC/DOPG lipid bilayer by molecular dynamics simulation

Antimicrobial peptides (AMPs) inactivate microorganisms by forming transmembrane pores in a cell membrane through adsorption and aggregation. Energetics of addition of an AMP to a transmembrane pore is important for evaluation of its formation and growth. Such information is essential for the characterization of pore forming ability of peptides in cell membranes. This study quantifies the potential of mean force through molecular dynamics (MD) simulation for the addition of melittin, a naturally occurring AMP, into a DOPC/DOPG mixed bilayer, a mimic of bacterial membrane, for different extents of insertion into either a bilayer or a pore consisting of three to six transmembrane peptides. The energy barrier for insertion of a melittin molecule into the bilayer was highest in the absence of transmembrane peptides and decreased for the number of transmembrane peptides from three to six, eventually approaching zero. The decrease in free energy for complete insertion of peptide was found to be higher for larger pore size. Water channel formation occurred only for insertion into pores consisting of three or more transmembrane peptides with the radius of water channel being larger for a larger number of transmembrane peptides. The structure of the pore was found to be paraboloid. The estimated free energy barrier for insertion of melittin into an ideal paraboloid pore accounting for different intermolecular interactions was consistent with MD simulation results. The results reported in this manuscript will be useful for the development of a model for nucleation of pores and a rational methodology for selection of synthetic antimicrobial peptides.

Effect of physicochemical properties of peptides from soy protein on their antimicrobial activity

Antimicrobial peptides (AMPs) kill microbial cells through insertion and damage/permeabilization of the cytoplasmic cell membranes and has applications in food safety and antibiotic replacement. Soy protein is an attractive, abundant natural source for commercial production of AMPs. In this research, explicit solvent molecular dynamics (MD) simulation was employed to investigate the effects of (i) number of total and net charges, (ii) hydrophobicity (iii) hydrophobic moment and (iv) helicity of peptides from soy protein on their ability to bind to lipid bilayer and their transmembrane aggregates to form pores. Interaction of possible AMP segments from soy protein with 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine/1-palmitoyl-2-oleoyl-sn-glycero-3-phosphoglycerol (POPC/POPG) bilayers, a mimic of bacterial cell membrane, was investigated. Pore formation was insensitive to helicity and occurred for hydrophobicity threshold in the range of -0.3-0kcal/mol, hydrophobic moment threshold of 0.3kcal/mol, net charge threshold of 2. Though low hydrophobicity and high number of charges help in the formation of water channel for transmembrane aggregates, insertion of peptides with these properties requires overcome of energy barrier, as shown by potential of mean force calculations, thereby resulting in low antimicrobial activity. Experimental evaluation of antimicrobial activity of these peptides against Gram positive L. monocytogenes and Gram negative E. coli as obtained by spot-on-lawn assay was consistent with simulation results. These results should help in the development of guidelines for selection of peptides with antimicrobial activity based on their physicochemical properties.

Activation of Na+/H+ exchanger other than formation of transmembrane pore underlies the cytotoxicity of nematocyst venom from Chrysaora helvola Brandt jellyfish

We previously reported unexpected apoptosis-like cell death induced by nematocyst venom (NV) from Chrysaora helvola Brandt (C. helvola) jellyfish. To assess whether the pore formation mechanism underlay the action of NV, the change in cell membrane permeability was studied in both chicken erythrocytes and human CNE-2 cells. Initially, paradoxical results were derived from osmoprotectant protection assays. Polyethylene glycol (PEG)₂₀₀₀, which completely inhibited the NV induced hemolysis, failed to protect CNE-2 cells. Detailed experiments showed that PEG protection from hemolysis is concentration dependent and indicated caution when estimating the pore size formed by NV with the osmotic protection method. NV-treated CNE-2 cells remained impermeable to dyes with various molecular weights (MWs) (622.6-40,000 Da). Furthermore, membrane depolarization and selective permeability to Na⁺ other than K⁺ were induced in CNE-2 cells. No oxidative damage to the cell membrane was detected. Amiloride, an inhibitor of Na⁺/H⁺ exchanger (NHE), substantially protected both CNE-2 cells and erythrocytes from NV. Combined with the previously reported increase in intracellular pH, we supposed that NV activated plasma membrane NHE without forming transmembrane pores. Interestingly, glutathione (GSH) showed significant protection to CNE-2 cells while potentiating the hemolytic power of NV. This finding may suggest a key role of reactive oxygen species (ROS) in the cytotoxicity of NV. To the best of our knowledge, this is the first report that a hemolytic jellyfish venom acts through NHE in a manner other than compromising membrane integrity. The current work provides new insight into the arsenal of toxic jellyfishes.

Effect of immobilization on the antimicrobial activity of a cysteine-terminated antimicrobial Peptide Cecropin P1 tethered to silica nanoparticle against E. coli O157:H7 EDL933

Antimicrobial peptides (AMPs) have the ability to penetrate the cell membrane, form pores which eventually lead to cell death. Immobilization of AMP on nanoparticles can play a major role in antimicrobial materials, biosensors for pathogen detection and in food safety. The minimum inhibitory concentration (MIC) of free Cecropin P1 (CP1, sequence SWLSTAKKLENSAKKRLSEGIAIAIQGGPR) and adsorbed on silica nanoparticle against E. coli O157:H7 EDL933 were 0.78μg/ml. This was found to be consistent with preservation of α-helical secondary structure of CP1 upon adsorption as indicated by circular dichroism (CD). Cysteine-terminus modified Cecropin P1 (CP1C, sequence SWLSTAKKLENSAKKRLSEGIAIAIQGGPRC) was chemically immobilized onto silica nanoparticles with maleimide-PEG-NHS ester cross-linkers of different PEG chain lengths. The antimicrobial activity of CP1C in solution and adsorbed on silica nanoparticles against E. coli O157:H7 EDL933 were found to be the same as those for CP1. However, tethered CP1C exhibited much higher MIC of 24.38, 37.55 and 109.82μg/ml for (PEG)₂₀, (PEG)₆ and (PEG)₂ linkers respectively. The antimicrobial activity of CP1C tethered to silica nanoparticles with (PEG)₂₀ linker was found to be lower for lower surface coverage with MIC values being 86.06, 36.89, 24.38 and 17.84μg/ml for surface coverage of 12.3%, 24.4%, 52.8% and 83.8% respectively. All atom MD simulation of 1:3 DOPG/DOPC mixed membrane interacting with free and PEGlyated CP1C indicated that presence of PEG linker prevented CP1C from interacting with the bilayer which may explain the loss of antimicrobial activity of tethered CP1C.

Nanosystem trends in drug delivery using quality-by-design concept

Quality by design (QbD) has become an inevitable trend because of its benefits for product quality and process understanding. Trials have been conducted using QbD in nanosystems' optimization. This paper reviews the application of QbD for processing nanosystems and summarizes the application procedure. It provides prospective guidelines for future investigations that apply QbD to nanosystem manufacturing processes. Employing the QbD concept in this way is a novel area in nanosystem quality.

Methodology for identification of pore forming antimicrobial peptides from soy protein subunits β-conglycinin and glycinin

Antimicrobial peptides (AMPs) inactivate microbial cells through pore formation in cell membrane. Because of their different mode of action compared to antibiotics, AMPs can be effectively used to combat drug resistant bacteria in human health. AMPs can also be used to replace antibiotics in animal feed and immobilized on food packaging films. In this research, we developed a methodology based on mechanistic evaluation of peptide-lipid bilayer interaction to identify AMPs from soy protein. Production of AMPs from soy protein is an attractive, cost-saving alternative for commercial consideration, because soy protein is an abundant and common protein resource. This methodology is also applicable for identification of AMPs from any protein. Initial screening of peptide segments from soy glycinin (11S) and soy β-conglycinin (7S) subunits was based on their hydrophobicity, hydrophobic moment and net charge. Delicate balance between hydrophilic and hydrophobic interactions is necessary for pore formation. High hydrophobicity decreases the peptide solubility in aqueous phase whereas high hydrophilicity limits binding of the peptide to the bilayer. Out of several candidates chosen from the initial screening, two peptides satisfied the criteria for antimicrobial activity, viz. (i) lipid-peptide binding in surface state and (ii) pore formation in transmembrane state of the aggregate. This method of identification of antimicrobial activity via molecular dynamics simulation was shown to be robust in that it is insensitive to the number of peptides employed in the simulation, initial peptide structure and force field. Their antimicrobial activity against Listeria monocytogenes and Escherichia coli was further confirmed by spot-on-lawn test.

Characterization of antimicrobial activity against Listeria and cytotoxicity of native melittin and its mutant variants

Antimicrobial peptides (AMPs) are relatively short peptides that have the ability to penetrate the cell membrane, form pores leading to cell death. This study compares both antimicrobial activity and cytotoxicity of native melittin and its two mutants, namely, melittin I17K (GIGAVLKVLTTGLPALKSWIKRKRQQ) with a higher charge and lower hydrophobicity and mutant G1I (IIGAVLKVLTTGLPALISWIKRKRQQ) of higher hydrophobicity. The antimicrobial activity against different strains of Listeria was investigated by bioassay, viability studies, fluorescence and transmission electron microscopy. Cytotoxicity was examined by lactate dehydrogenase (LDH) assay on mammalian Caco-2 cells. The minimum inhibitory concentration of native, mutant I17K, mutant G1I against Listeria monocytogenes F4244 was 0.315±0.008, 0.814±0.006 and 0.494±0.037μg/ml respectively, whereas the minimum bactericidal concentration values were 3.263±0.0034, 7.412±0.017 and 5.366±0.019μg/ml respectively. Lag time for inactivation of L. monocytogenes F4244 was observed at concentrations below 0.20 and 0.78μg/ml for native and mutant melittin I17K respectively. The antimicrobial activity against L. monocytogenes F4244 was in the order native>G1I>I17K. Native melittin was cytotoxic to mammalian Caco-2 cells above concentration of 2μg/ml, whereas the two mutants exhibited negligible cytotoxicity up to a concentration of 8μg/ml. Pore formation in cell wall/membrane was observed by transmission electron microscopy. Molecular dynamics (MD) simulation of native and its mutants indicated that (i) surface native melittin and G1I exhibited higher tendency to penetrate a mimic of bacterial cell membrane and (ii) transmembrane native and I17K formed water channel in mimics of bacterial and mammalian cell membranes.