Single wall carbon nanotubes polymerization under compression: An atomistic molecular dynamics study

New carbon allotropes derived from nanotubes via a three-fold distortion mechanism

Besides commonly used graphite, carbon nanotubes are also often chosen as precursor materials for the synthesis of new carbon phases. Here we identify, using ab initio calculations, two new three-dimensional crystalline modifications of carbon nanotubes with P63/mcm (D36h) symmetry derived from (6,0) and (9,0) nanotubes via a three-fold distortion assisted reconstruction mechanism. The resulting sp2 + sp3 hybrid network structures have a 24- and 36-atom hexagonal unit cell, termed as (6,0)-hP24 and (9,0)-hP36 carbon, and they topologically correspond to two-dimensional graphyne and graphdiyne. Total-energy calculations show that they are energetically more stable than the original nanotubes and previously reported polymerized nanotube structures. Their dynamic stability has been confirmed by phonon mode analysis. Electronic band structure calculations reveal that they are semiconductors with an indirect band gap of 0.18 eV for hP24, and a direct band gap of 2.15 eV for hP36. The present results establish a new type of carbon phase and offer insights into understanding the complex structural landscape of polymerized nanotubes.

Mechanical properties and electronic structure of edge-doped graphene nanoribbons with F, O, and Cl atoms

In this study, we present the structural, electronic, and mechanical properties of edge-doped zigzag graphene nanoribbons (ZGNRs) doped with fluorine, oxygen, and chlorine atoms. To the best of our knowledge, to date, no experimental results concerning the mechanical properties of graphene-derived nanoribbons have been reported in the literature. Simulations indicate that Cl- and F-doped ZGNRs present an equivalent 2-dimensional Young's modulus E^2D, which seems to be higher than those of graphene and H-doped ZGNRs. This is a consequence of the electronic structure of the system, particularly originating from strong interactions between the dopant atoms localized at the edges. The interaction between dopant atoms located at the edges is higher for Cl and lower for F and O atoms. This is the origin of the observed trend, in which E > E > E for all the analyzed ZGNRs.

Direct Intertube Cross-Linking of Carbon Nanotubes at Room Temperature

Carbon nanotubes (CNTs) have long been regarded as an efficient free radical scavenger because of the large-conjugation system in their electronic structures. Hence, despite abundant reports on CNT reacting with incoming free radical species, current research has not seen CNT itself displaying the chemical reactivity of free radicals. Here we show that reactive free radicals can in fact be generated on carbon nanotubes via reductive defluorination of highly fluorinated single-walled carbon nanotubes (FSWNTs). This finding not only enriches the current understanding of carbon nanotube chemical reactivity but also opens up new opportunities in CNT-based material design. For example, spacer-free direct intertube cross-linking of carbon nanotubes was previously achieved only under extremely high temperature and pressure or electron/ion beam irradiation. With the free radicals on defluorinated FSWNTs, the nanotubes containing multiple radicals on the sidewall can directly cross-link with each other under ambient temperature through intertube radical recombination. It is demonstrated that carbon nanotube fibers reinforced via direct cross-linking displays much improved mechanical properties.

Polyaniline/carbon nanotube sheet nanocomposites: fabrication and characterization

Practical approaches are needed to take advantage of the nanometer-scale mechanical properties of carbon nanotubes (CNTs) at the macroscopic scale. This study was conducted to elucidate the salient factors that can maximize the mechanical properties of nanocomposites fabricated from commercially available CNT sheets. The CNT sheets were modified by stretching to improve CNT alignment and in situ polymerization using polyaniline (PANI), a π-conjugated conductive polymer, as a binder. The resulting CNT nanocomposites were subsequently postprocessed by hot pressing and/or high temperature treatment to carbonize the PANI as a means to improve mechanical properties. The PANI/CNT nanocomposites demonstrated significant improvement in mechanical properties compared to pristine CNT sheets. The highest specific tensile strength of PANI/stretched CNT nanocomposite was 484 MPa/(g/cm3), which was achieved in a sample with ∼42 wt % of PANI. This specimen was fabricated by in situ polymerization followed by hot pressing. The highest specific Young's modulus of 17.1 GPa/(g/cm3) was measured on a sample that was hot-pressed and carbonized. In addition, the highest DC-electrical conductivity of 621 S/cm was obtained on a sample prepared by in situ polymerization of PANI on a stretched CNT sheet.

In situ mechanical property measurements of amorphous carbon-boron nitride nanotube nanostructures

To understand the mechanical properties of amorphous carbon (a-C)/boron nitride nanotube (BNNT) nanostructures, in situ mechanical tests are conducted inside a transmission electron microscope equipped with an integrated atomic force microscope system. The nanotube structure is modified with amorphous carbon deposited by controlled electron beam irradiation. We demonstrate multiple in situ tensile, compressive, and lap shear tests with a-C/BNNT hybrid nanostructures. The tensile strength of the a-C/BNNT hybrid nanostructure is 5.29 GPa with about 90 vol% of a-C. The tensile strength and strain of the end-to-end joint structure with a-C welding is 0.8 GPa and 5.2% whereas the lap shear strength of the side-by-side joint structure with a-C is 0.25 GPa.

Mechanical properties of graphene nanoribbons

Herein, we investigate the structural, electronic and mechanical properties of zigzag graphene nanoribbons in the presence of stress by applying density functional theory within the GGA-PBE (generalized gradient approximation-Perdew-Burke-Ernzerhof) approximation. The uniaxial stress is applied along the periodic direction, allowing a unitary deformation in the range of ± 0.02%. The mechanical properties show a linear response within that range while a nonlinear dependence is found for higher strain. The most relevant results indicate that Young's modulus is considerable higher than those determined for graphene and carbon nanotubes. The geometrical reconstruction of the C-C bonds at the edges hardens the nanostructure. The features of the electronic structure are not sensitive to strain in this linear elastic regime, suggesting the potential for using carbon nanostructures in nano-electronic devices in the near future.

Molecular dynamics simulation of single wall carbon nanotubes polymerization under compression

Single wall carbon nanotubes (SWCNTs) often aggregate into bundles of hundreds of weakly interacting tubes. Their cross-polymerization opens new possibilities for the creation of new super-hard materials. New mechanical and electronic properties are expected from these condensed structures, as well as novel potential applications. Previous theoretical results presented geometric modifications involving changes in the radial section of the compressed tubes as the explanation to the experimental measurements of structural changes during tube compression. We report here results from molecular dynamics simulations of the SWCNTs polymerization for small diameter arm chair tubes under compression. Hydrostatic and piston-type compression of SWCNTs have been simulated for different temperatures and rates of compression. Our results indicate that large diameter tubes (10,10) are unlike to polymerize while small diameter ones (around 5 A) polymerize even at room temperature. Other interesting results are the observation of the appearance of spontaneous scroll-like structures and also the so-called tubulane motifs, which were predicted in the literature more than a decade ago.

Polymerization of Carbon Nanotubes through Self-Irradiation

We have investigated the formation of cross-links between neighboring carbon nanotubes within a bundle. Classical molecular dynamics was used to follow the evolution of the system when it is bombarded by low-energy carbon atoms. We show that it is possible to polymerize carbon nanotubes through irradiation and discuss the most common types of defects produced. Cross-links are created mainly in the direction perpendicular to the surface, and for higher energies, defects are created deeper in the rope. The final defects geometries may provide a realistic input to electronic density first principle calculations.