Dual-signal anodic stripping voltammetric determination of trace arsenic(III) at a glassy carbon electrode modified with internal-electrolysis deposited gold nanoparticles

Highly sensitive and selective anodic stripping voltammetric procedure of As(III) determination following double deposition and double stripping steps mode in combination with a flow system

Double deposition and double stripping steps mode was used for the first time in combination with a flow system for anodic stripping voltammetric determination of As(III) ions. The proposed way of the voltammetric measurements leads to a decrease of the detection limit as compared to the values obtained using a traditional three-electrode system thanks to an initial preconcentration of the analyte on the first working electrode as well as the significant increase of the selectivity of As(III) determination thanks to the application of a flow system. Optimization of the analytical procedure was performed. The calibration curve of As(III) determination was a straight line in the range from 1 × 10-9 to 5 × 10-8 mol L-1. The estimated detection limit was 4.8 × 10-10 mol L-1 (deposition time of 120 s at both working electrodes). The repeatability of the proposed procedure calculated as RSD% for As(III) at a concentration of 1 × 10-8 mol L-1 was 3.8 % (n = 7). The tolerable limit of Cu(II) excess was significantly increased thanks to the solution exchange after the first deposition step. The correctness of the proposed procedure was confirmed by analysis of a real water sample and lake water certified reference material by obtaining satisfactory recovery values.

Anodic stripping voltammetry of arsenic determination with edible mushroom-nafion-modified glassy carbon electrode

An edible Mushroom-Nafion modified glassy carbon electrode (M2N5-GCE) was prepared using a homogeneous mixture varying the concentrations of these, in addition to the origin of the mushroom (Shiitake, Lentinula edodes, M1 and Abrantes, Agariscus bisporus, M2) and applied to the As(III) determination by anodic stripping voltammetry. After choosing the optimal conditions in the preparation of the electrode, the second stage was to study the effects of various parameters such as supporting electrolyte, pH, accumulation potential, and time (Eacc, tacc). The optimum experimental conditions chosen were Britton Robinson buffer 0.01 mol L-1 pH:4.6; Eacc: -1.0 and tacc: 60 s obtaining a signal of oxidation of As(0) to As(III) about 0.08 V. Peak current was proportional to arsenic concentration over the 19.6-117.6 μg L-1 range, with a 3σ detection limit of 13.4 μg L-1. The method was validated using As(III) spiked tap water from the laboratory with satisfactory results (RE:3.0 %). Finally, the method was applied to the determination of As(III) in water samples from the Loa River (Northern Chile) in the presence of As(V) in a concentration >20 times higher (RE: 2.3 %).

A Schiff base modified graphene oxide film for anodic stripping voltammetric determination of arsenite

A protocol is described for chemical modification of graphene oxide with a Schiff base derived from diethylenetriamine and 2-hydroxy-4-methoxybenzophenone. The base was grafted onto an indium tin oxide (ITO) film and applied to electroanalytical determination of arsenite. Successful grafting was confirmed by Fourier transform-infrared spectroscopy, spectrophotometry, field emission scanning electron microscopy and cyclic voltammetry. Secondly, the coated ITO film served as a working electrode for the stripping voltammetric determination of arsenite. The analytical signal is generated by selective oxidation of metal species via multi-donor sites present in the derivatized Schiff base. The electroanalytical protocol was optimized by investigating the effects of deposition time, working potential, frequency and amplitude of square wave anodic stripping voltammetry. The method has attractive features including (a) the usage of a non-metallic, non-toxic and cost-effective material; (b) improved sensitivity (with limit of detection as low as 156 pM) due to better adsorption of arsenite in the Schiff base pockets on the ITO, and (c) the application to the determination of arsenite in real samples. Graphical abstract Schematic representation of the fabrication of a Schiff base-functionalized graphene oxide on an indium tin oxide (SB@SiO2@GO@ITO) electrode for selective electrochemical sensing of arsenite due to adsorption on multi-donor sites.

Trace Arsenic Determination in a TiO2 Pigment Matrix Using Electrothermal Atomic Absorption Spectrometry

This work describes the use of electrothermal atomic absorption spectrometry in combination with a pyrolytic graphite-coated tube with a platform for trace arsenic (As) determination in titanium dioxide (TiO₂) pigment. This type of matrix is challenging, as complete digestion in hydrofluoric acid-containing solution is needed. First, closed-vessel microwave digestion was performed for the full-sample decomposition. Next, a temperature program was optimized for drying, pyrolysis, and atomization temperatures. Furthermore, the use of a chemical modifier mixture was proposed that reduced the background contribution and prevented significant analyte loss and therefore improved the analytical procedure. The optimized method was validated for the detection (LOD) and quantification (LOQ) limits, the linear concentration range, accuracy, and precision. Special attention was devoted to the matrix-matching solutions in the calibration procedure. Linearity was confirmed in the 5.0 to 100.0 µg/L concentration range (R² = 0.999). The average recovery for 16 different real TiO₂ pigment samples was 92.0%, and the relative standard deviation value for six replicate measurements was ≤10.4%. Moreover, the LOD and LOQ in terms of the TiO₂ pigment mass was determined to be 0.2 µg/(g TiO₂) and 0.7 µg/(g TiO₂), respectively. The latter complies with Commission Directive 2008/128/EC, which does not allow more than 3 µg As/(g product) as the specific criteria of purity. Finally, based on scanning electron microscopy analysis of unused and several times used pyrolytic graphite-coated tubes, usage of the tube 250 times before replacement is recommended.

Electrochemical oxidation of As(iii) on Pd immobilized Pt surface: kinetics and sensing performance

Pd nanoparticles were electrochemically immobilized on a Pt surface in the presence of sodium dodecyl sulfate (SDS) molecules to study the electrokinetics of arsenite oxidation reactions and the corresponding sensing activities. The X-ray photoelectron spectroscopy (XPS) analysis showed that on the Pt surface, Pd atoms exist as adatoms and the contents of Pd(0) and Pd(ii) were 75.72 and 24.28 at%, respectively, and the particle sizes were in the range of 61-145 nm. The experimental results revealed that the catalytic efficiency as well as the charge transfer resistance (at the redox potential of the Fe(ii)/Fe(iii) couple) increased in the order of Pt < Pt-Pd < Pt-Pdsds. A Pt-Pdsds electrode exhibited an open circuit potential (OCP) of 0.65 V in acidic conditions; however, when 50.0 mM NaAsO2 was present, the OCP value shifted to 0.42 V. It has been projected that the As(iii) oxidation proceeds using a sequential pathway: As(iii) → As(iv) → As(v). After optimization of the square wave voltammetric data, the limits of detection of As(iii) were obtained as 1.3 μg L-1 and 0.2 μg L-1 when the surface modification of the Pt surface was executed with Pd particles in the absence and presence of the SDS surfactant, respectively. Finally, real samples were analyzed with excellent recovery performance.

Label-free signal-on aptasensor for sensitive electrochemical detection of arsenite

A signal-on aptasensor was fabricated for highly sensitive and selective electrochemical detection of arsenite with a label-free Ars-3 aptamer self-assembled on a screen-printed carbon electrode (SPCE) via Au-S bond. The Ars-3 aptamer could adsorb cationic polydiallyldimethylammonium (PDDA) via electrostatic interaction to repel other cationic species. In the presence of arsenite, the change of Ars-3 conformation due to the formation of Ars-3/arsenite complex led to less adsorption of PDDA, and the complex could adsorb more positively charged [Ru(NH3)6](3+) as an electrochemically active indicator on the aptasensor surface, which produced a sensitive "turn-on" response. The target-induced structure switching could be used for sensitive detection of arsenite with a linear range from 0.2 nM to 100 nM and a detection limit down to 0.15 nM. Benefiting from Ars-3 aptamer, the proposed system exhibited excellent specificity against other heavy metal ions. The SPCE-based aptasensor exhibited the advantages of low cost and simple fabrication, providing potential application of arsenite detection in environment.

Arsenic and antimony in water and wastewater: overview of removal techniques with special reference to latest advances in adsorption

Arsenic and antimony are metalloids, naturally present in the environment but also introduced by human activities. Both elements are toxic and carcinogenic, and their removal from water is of unquestionable importance. The present article begins with an overview of As and Sb chemistry, distribution and toxicity, which are relevant aspects to understand and develop remediation techniques. A brief review of the recent results in analytical methods for speciation and quantification was also provided. The most common As and Sb removal techniques (coagulation/flocculation, oxidation, membrane processes, electrochemical methods and phyto and bioremediation) are presented with discussion of their advantages, drawbacks and the main recent achievements. Literature review on adsorption and biosorption were focused in detail. Considering especially the case of developing countries or rural communities, but also the finite energy resources that over the world are still dependent, recent research have focused especially readily available low-cost adsorbents, as minerals, wastes and biosorbents. Many of these alternative sorbents have been presenting promising results and can be even superior when compared to the commercial ones. Sorption capacities were accurately compiled for As(III,V) and Sb(III,V) species in order to provide to the reader an easy but detailed comparison. Some aspects related to experimental conditions, comparison criteria, lack of research studies, economic aspects and adsorption mechanisms were critically discussed.

Exploiting differential electrochemical stripping behaviors of Fe3O4 nanocrystals toward heavy metal ions by crystal cutting

This study attempts to understand the intrinsic impact of different morphologies of nanocrystals on their electrochemical stripping behaviors toward heavy metal ions. Two differently shaped Fe3O4 nanocrystals, i.e., (100)-bound cubic and (111)-bound octahedral, have been synthesized for the experiments. Electrochemical results indicate that Fe3O4 nanocrystals with different shapes show different stripping behaviors toward heavy metal ions. Octahedral Fe3O4 nanocrystals show better electrochemical sensing performances toward the investigated heavy metal ions such as Zn(II), Cd(II), Pb(II), Cu(II), and Hg(II), in comparison with cubic ones. Specifically, Pb(II) is found to have the best stripping performance on both the (100) and (111) facets. To clarify these phenomena, adsorption abilities of as-prepared Fe3O4 nanocrystals have been investigated toward heavy metal ions. Most importantly, combined with theoretical calculations, their different electrochemical stripping behaviors in view of facet effects have been further studied and enclosed at the level of molecular/atom. Finally, as a trial to find a disposable platform completely free from noble metals, the potential application of the Fe3O4 nanocrystals for electrochemical detection of As(III) in drinking water is demonstrated.