Preparation of PAA-g-CTAB/PANI polymer based gel-electrolyte and the application in quasi-solid-state dye-sensitized solar cells

Rapid-Response and Wide-Range pH Sensors Enabled by Self-Assembled Functional PAni/PAA Layer on No-Core Fiber

The measurement of pH has received great attention in diverse fields, such as clinical diagnostics, environmental protection, and food safety. Optical fiber sensors are widely used for pH sensing because of their great advantages. In this work, an optical fiber pH sensor is fabricated, by combining the merits of the multimode interference configuration and pH-sensitive polyaniline/polyacrylic acid (PAni/PAA) coatings, which was successfully in situ deposited on the no-core fiber (NCF) by the layer-by-layer (LBL) self-assembly method. The sensors' performance was experimentally characterized when used for pH detection. It has a high sensitivity of 0.985 nm/pH and a great linear response in a universal pH range of 2-12. The response time and recovery time is measured to be less than 10 s. In addition, its temperature sensitivity is tested to be about 0.01 nm/°C with a low temperature crosstalk effect, which makes it promising for detecting pH in the liquid phase with temperature variation. The sensors also demonstrated easy fabrication, good stability, and repeatability, which are adapted to pH detection in most practical applications.

Effect of PEG Molecular Weight on the Polyurethane-Based Quasi-Solid-State Electrolyte for Dye-Sensitized Solar Cells

Nanosilica was surface modified with polyaniline and incorporated into polyurethane to form a polymer matrix capable of entrapping a liquid electrolyte and functioning as quasi-solid-state electrolyte in the dye-sensitized solar cells. The effect on the S−PANi distribution, surface morphology, thermal stability, gel content, and structural change after varying the PEG molecular weight of the polyurethane matrix was analyzed. Quasi-solid-state electrolytes were prepared by immersing the polyurethane matrix into a liquid electrolyte and the polymer matrix absorbency, conductivity, and ion diffusion were investigated. The formulated quasi-solid-state electrolytes were applied in dye-sensitized solar cells and their charge recombination, photovoltaic performance, and lifespan were measured. The quasi-solid-state electrolyte with a PEG molecular weight of 2000 gmol−1 (PU−PEG 2000) demonstrated the highest light-to-energy conversion efficiency, namely, 3.41%, with an open-circuit voltage of 720 mV, a short-circuit current of 4.52 mA cm−2, and a fill factor of 0.63.

Facile synthesis of water-dispersible poly(3-hexylthiophene) nanoparticles with high yield and excellent colloidal stability

There has been growing interest in water-processable conjugated polymers for biocompatible devices. However, some broadly used conjugated polymers like poly(3-hexylthiophene) (P3HT) are hydrophobic and they cannot be processed in water. We herein report a facile yet highly efficient assembly method to prepare water-dispersible pyridine-containing P3HT (Py-P3HT) nanoparticles (NPs) with a high yield (>80%) and a fine size below 100 nm. It is based on the fast nanoprecipitation of Py-P3HT stabilized by hydrophilic poly(acrylic acid) (PAA). Py-P3HT can form spherical NPs at a concentration up to 0.2 mg/mL with a diameter of ∼75 nm at a very low concentration of PAA, e.g., 0.01-0.1 mg/mL, as surface ligands. Those negatively charged Py-P3HT NPs can bind with metal cations and further support the growth of noble metal NPs like Ag and Au. Our self-assembly methodology potentially opens new doors to process and directly use hydrophobic conjugated polymers in a much broader context.

Conducting polymer hydrogels as a sustainable platform for advanced energy, biomedical and environmental applications

Environmentally friendly polymeric materials and derivative technologies play increasingly important roles in the sustainable development of our modern society. Conducting polymer hydrogels (CPHs) synergizing the advantageous characteristics of conventional hydrogels and conducting polymers are promising to satisfy the requirements of environmental sustainability. Beyond their use in energy and biomedical applications that require exceptional mechanical and electrical properties, CPHs are emerging as promising contaminant adsorbents owing to their porous network structure and regulable functional groups. Here, we review the currently available strategies for synthesizing CPHs, focusing primarily on multifunctional applications in energy storage/conversion, biomedical engineering and environmental remediation, and discuss future perspectives and challenges for CPHs in terms of their synthesis and applications. It is envisioned to stimulate new thinking and innovation in the development of next-generation sustainable materials.

A chemically bonded supercapacitor using a highly stretchable and adhesive gel polymer electrolyte based on an ionic liquid and epoxy-triblock diamine network

Despite significant advances in the development of flexible gel polymer electrolytes (GPEs), there are still problems to be addressed to apply them to flexible electric double layer capacitors (EDLCs), including interfacial interactions between the electrolyte and electrode under deformation. Previously reported EDLCs using GPEs have laminated structures with weak interfacial interactions between the electrode and electrolyte, leading to fragility upon elongation and low power density due to lower utilization of the surface area of the carbon material in the electrode. To overcome these problems, we present a new strategy for constructing an epoxy-based GPE that can provide strong adhesion between electrode and electrolyte. The GPE is synthesized by polymerization of epoxy and an ionic liquid. This GPE shows high flexibility up to 509% and excellent adhesive properties that enable strong chemical bonding between the electrode and electrolyte. Moreover, the GPE is stable at high voltage and high temperature with high ionic conductivity of ∼10⁻³ S cm⁻¹. EDLCs based on the developed GPE exhibit good compatibility between the electrode and electrolyte and work properly when deformed. The EDLCs also show a high specific capacitance of 99 F g⁻¹, energy density of 113 W h kg⁻¹, and power density of 4.5 kW g⁻¹. The excellent performance of the GPE gives it tremendous potential for use in next generation electronic devices such as wearable devices.

A chemically bonded supercapacitor using a stretchable and adhesive gel polymer electrolyte based on ionic liquid and epoxy for flexible devices.

Ultrasonic irradiation preparation of graphitic-C3N4/polyaniline nanocomposites as counter electrodes for dye-sensitized solar cells

In this research, polyaniline/graphitic carbon nitride (PANI/g-C₃N₄) nanocomposites were synthesized via in-situ electrochemical polymerization of aniline monomer whit different number of cyclic voltammetry scans (10, 20 and 30 cycles) after electrode surface pre-preparation using a potential shock under ultrasonic irradiation. PANI/g-C₃N₄ nanocomposites with two values of g-C₃N₄ (0.010 wt% and 0.015 wt%) were deposited on the surface of the transparent conducting film (FTO glass) by immersing FTO into the aniline solution and g-C₃N₄ during the electro-polymerization. The resulting PANI/g-C₃N₄ films were characterized by Fourier transformed infra-red (FTIR), power X-ray diffraction (PXRD), field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM) techniques. The prepared electrodes were applied as counter electrode in dye-sensitized solar cells. Among them, the prepared electrode with 10 cycles and 0.01 wt% g-C₃N₄ showed the best efficiency. These hybrids show good catalytic activity in elevating tri-iodide reduction and due to the synergistic effect of PANI and g-C₃N₄, PANI/g-C₃N₄ nanocomposite electrode shows power conversion efficiency about 1.8%.

The potential of incorporation of binary salts and ionic liquid in P(VP-co-VAc) gel polymer electrolyte in electrochemical and photovoltaic performances

In this study, dye-sensitized solar cells (DSSCs) has been assembled with poly(1-vinylpyrrolidone-co-vinyl acetate) (P(VP-co-VAc)) gel polymer electrolytes (GPEs) which have been incorporated with binary salt and an ionic liquid. The potential of this combination was studied and reported. The binary salt system GPEs was having ionic conductivity and power conversion efficiency (PCE) that could reach up to 1.90 × 10⁻³ S cm⁻¹ and 5.53%, respectively. Interestingly, upon the addition of the ionic liquid, MPII into the binary salt system the ionic conductivity and PCE had risen steadily up to 4.09 × 10⁻³ S cm⁻¹ and 5.94%, respectively. In order to know more about this phenomenon, the electrochemical impedance studies (EIS) of the GPE samples have been done and reported. Fourier transform infrared studies (FTIR) and thermogravimetric analysis (TGA) have also been studied to understand more on the structural and thermal properties of the GPEs. The Nyquist plot and Bodes plot studies have been done in order to understand the electrochemical properties of the GPE based DSSCs and Tafel polarization studies were done to determine the electrocatalytic activity of the GPE samples.

Poly(Acrylic acid)⁻Based Hybrid Inorganic⁻Organic Electrolytes Membrane for Electrical Double Layer Capacitors Application

Nanocomposite polymer electrolyte membranes (NCPEMs) based on poly(acrylic acid)(PAA) and titania (TiO₂) are prepared by a solution casting technique. The ionic conductivity of NCPEMs increases with the weight ratio of TiO₂.The highest ionic conductivity of (8.36 ± 0.01) × 10^-4 S·cm^-1 is obtained with addition of 6 wt % of TiO₂ at ambient temperature. The complexation between PAA, LiTFSI and TiO₂ is discussed in Attenuated total reflectance-Fourier Transform Infrared (ATR-FTIR) studies. Electrical double layer capacitors (EDLCs) are fabricated using the filler-free polymer electrolyte or the most conducting NCPEM and carbon-based electrodes. The electrochemical performances of fabricated EDLCs are studied through cyclic voltammetry (CV) and galvanostatic charge-discharge studies. EDLC comprising NCPEM shows the specific capacitance of 28.56 F·g^-1 (or equivalent to 29.54 mF·cm^-2) with excellent electrochemical stability.

Graphene-incorporated quasi-solid-state dye-sensitized solar cells

To reduce fabrication cost and simplify the preparation technique, a DSSC comprising a graphene/TiO₂ anode, a PAA–PEG/graphene gel electrolyte, and a graphene CE is fabricated, yielding an efficiency of 3.62%.