Electrochemical synthesis of layer-by-layer reduced graphene oxide sheets/polyaniline nanofibers composite and its electrochemical performance

Metal-Free Graphene-Based Derivatives as Oxygen Reduction Reaction Electrocatalysts in Energy Conversion and Storage Systems: An Overview

Oxygen reduction reaction (ORR) is one of the most important reactions in electrochemical energy storage and conversion devices. To overcome the slow kinetics, minimize the overpotential, and make this reaction feasible, efficient, and stable, electrocatalysts are needed. Metal-free graphene-based systems are considered promising and cost-effective ORR catalysts with adjustable structures. This review is meant to give a rational overview of the graphene-based metal-free ORR electrocatalysts, illustrating the huge amount of related research developed particularly in the field of fuel cells and metal-air batteries, with particular attention to the synthesis procedures. The novelty of this review is that, beyond general aspects regarding the synthesis and characterization of graphene, above 90% of the various graphene (doped and undoped species, composites)-based ORR electrocatalysts have been reported, which represents an unprecedented thorough collection of both experimental and theoretical studies. Hundreds of references are included in the review; therefore, it can be considered as a vademecum in the field.

Mitigating Zinc Dendrite Formation and Parasitic Side Reactions in Aqueous Zn-Ion Batteries Via Laser-Assisted Carbonization of Cu-PANI Films on Zn Anodes

Aqueous zinc-ion batteries (ZIBs) are gaining attraction for large-scale energy storage systems due to their high safety, significant capacity, cost-effectiveness, and environmental friendliness. On the other hand, the development of aqueous ZIBs is restricted by the limited practical application of zinc (Zn) because of the high reactivity of Zn in aqueous electrolytes, which results in the severe dendrite growth and parasitic side reactions such as hydrogen evolution reaction (HER). In this study, heteroatom-doped carbon porous surface modification by laser-assisted carbonization of copper (Cu) doped polyaniline (PANI) is designed and fabricated on top of the Zn metal anode (c-Cu-PANI/Zn). The c-Cu-PANI surface-modified Zn anodes exhibit high electrochemical stability and performance during the Zn plating-stripping cycles and suppress the dendrite formation. The symmetrical cell and half-cell with the c-Cu-PANI/Zn anodes exhibit stable cycles for 6000 h and 100% Coulombic efficiency for 2500 cycles, respectively. Moreover, the c-Cu-PANI/Zn║V2O5 cell delivers a high specific capacity of 319 mAh g-1 at 0.2 A g-1, which is significantly higher than that of the bare Zn║V2O5 cell (240 mAh g-1). It is believed that applying c-Cu-PANI as a surface modification can enhance the stability and reversibility of the Zn anodes, therefore accelerating the commercialization of ZIBs.

Amplifying Reactivity of Bio-Inspired [FeFe]-Hydrogenase Mimics by Organic Nanotubes

A bio-inspired FeFe hydrogenase model which catalyses hydrogen evolution reaction (HER) in acidic solutions is immobilized in polyaniline (PANI)-based nanotubes. A combination of analytical techniques reveals that this construct maintains both the molecular signatures of the bio-inspired complex and the material properties of PANI. The amine and imine-rich environment of the PANI chain amplifies the inherent HER activity of the bio-inspired complex, allowing electrocatalytic HER at neutral pH, with lower overpotentials and higher current densities compared to the bio-inspired complex alone. This construct retains the oxygen stability of the bio-inspired complex and remains stable through several hours of aerobic electrolysis, producing only 6.5 % H₂O₂ from the competing oxygen reduction reaction (ORR).

Non-Substituted Imidazolium-Based Electrolytes as Potential Alternatives to the Conventional Acidic Electrolytes of Polyaniline-Based Electrode Materials for Supercapacitors

Although disubstituted imidazolium cation is sterically crowded, hundreds of ionic liquids based on this cation have been reported as electrolytes for energy storage devices. In contrast to disubstituted imidazolium, non-substituted imidazolium is uncrowded sterically and has not yet been investigated as an electrolyte, to the best of our knowledge. Hence, imidazolium hydrogen sulfate [Imi][HSO4], in mixture with water, was studied as an electrolyte for PANI-based electrode materials. For comparison, pyrrolidinium with hydrogen sulfate or p-toluene sulfonate ([Pyrr][HSO4] or [Pyrr][PTS]), in mixture with water, were also investigated as alternatives to the conventional electrolyte (i.e., aqueous H2SO4) for PANI electrodes. Walden plots of binary mixture ionic liquid-water weight ratios with the optimal ionic conductivity (i.e., [Imi][HSO4]/water 48/52 wt% (195.1 mS/cm), [Pyrr][HSO4]/water 41/59 wt% (186.6 mS/cm), and [Pyrr][PTS]/water 48/52 wt% (43.4 mS/cm) along with the electrochemical performances of PANI in these binary mixtures showed that [Pyrr][HSO4]aq or [Imi][HSO4]aq are convenient electrolytes for PANI/PIL, as opposed to [Pyrr][PTS]aq. Furthermore, replacing the conventional aqueous electrolyte H2SO4 with [Imi][HSO4] aq increased the specific capacitance of PANI/PIL from 249.8 to 268.5 F/g at 15 mV/s. Moreover, PANI/PIL electrodes displayed a quasi-ideal capacitive behavior in [Imi][HSO4]aq (the correction factor of CPE4 was 0.99). This primary study has shown that non-substituted imidazolium as an electrolyte could enhance the electrochemical performances of PANI electrodes and could be a good alternative to the conventional electrolyte.

Polyaniline-graphene based composites electrode materials in supercapacitor: synthesis, performance and prospects

Supercapacitors (SCs) have become one of the most popular energy-storage devices for high power density and fast charging/discharging capability. Polyaniline is a class of conductive polymer materials with ultra-high specific capacitance, and the excellent mechanical properties will play a key role in the research of flexible SCs. The synergistic effect between polyaniline and graphene is often used to overcome their respective inherent shortcomings, thus the high-performance polyaniline-graphene based nanocomposite electrode materials can be prepared. The development of graphene-polyaniline nanocomposites as electrode materials for SCs depends on their excellent microstructure design. However, it is still difficult to seek a balance between graphene performance and functionalization to improve the weak interfacial interaction between graphene and polyaniline. In this manuscript, the latest preparation methods, research progress and research results of graphene-polyaniline nanocomposites on SCs are reviewed, and the optimization of electrode structures and performances is discussed. Finally, the prospect of graphene-polyaniline composites is expected.

Exploring the redox characteristics of porous ZnCoS@rGO grown on nickel foam as a high-performance electrode for energy storage applications

A supercapattery is a device that combines the properties of batteries and supercapacitors, such as power density and energy density. A binary composite (zinc cobalt sulfide) and rGO are synthesized using a simple hydrothermal method and modified Hummers' method. A notable specific capacity (C_s) of 1254 C g^-1 is obtained in the ZnCoS@rGO case, which is higher than individual C_s of ZnS (975 C g^-1) and CoS (400 C g^-1). For the asymmetric (ASC) device (ZnCoS@rGO//PANI@AC), the PANI-doped activated carbon and ZnCoS@rGO are used as the cathode and anode respectively. A high C_m of 141 C g^-1 is achieved at 1.4 A g^-1. The ASC is exhibited an extraordinary energy density of 45 W h kg^-1 with a power density 5000 W kg^-1 at 1.4 A g^-1. To check the stability of the device, the ASC device is measured for 2000 charging/discharging cycles. The device showed improved coulombic efficiency of 94%. These findings confirmed that the two-dimensional materials provide the opportunities to design battery and supercapacitor hybrid devices.

Enhanced Storage Performance of PANI and PANI/Graphene Composites Synthesized in Protic Ionic Liquids

Polyaniline (PANI) was synthesized using oxidative polymerization in a mixture of water with pyrrolidinium hydrogen sulfate [Pyrr][HSO₄], which is a protic ionic liquid PIL. The obtained PANI (PANI/PIL) was compared with conventional PANI (PANI/HCl and PANI/HSO₄) in terms of their morphological, structural, and storage properties. The results demonstrate that the addition of this PIL to a polymerization medium leads to a fiber-like morphology, instead of a spherical-like morphology, of PANI/HSO₄ or an agglomerated morphology of PANI/HCl. In addition, PAN/PIL exhibits an improvement of the charge transfer kinetic and storage capability in H₂SO₄ 1 mol·L^-1, compared to PANI/HCl. The combination of PANI/PIL and graphene oxide (GO), on the other hand, was investigated by optimizing the PANI/GO weight ratio to achieve the nanocomposite material with the best performance. Our results indicate that the PANI/PIL/GO containing 16 wt% of GO material exhibits a high performance and stability (223 F·g^-1 at 10 A·g^-1 in H₂SO₄ 1 mol·L^-1, 4.9 Wh·Kg^-1, and 3700 W·Kg^-1 @ 10 A·g^-1). The obtained results highlight the beneficial role of PIL in building PANI and PANI/GO nanocomposites with excellent performances for supercapacitor applications.

Enhanced Supercapacitor Performance Using a Co3 O4 @Co3 S4 Nanocomposite on Reduced Graphene Oxide/Ni Foam Electrodes

To avoid an enormous energy crisis in the not-too-distant future, it be emergent to establish high-performance energy storage devices such as supercapacitors. For this purpose, a three-dimensional (3D) heterostructure of Co₃ O₄ and Co₃ S₄ on nickel foam (NF) that is covered by reduced graphene oxide (rGO) has been prepared by following a facile multistep method. At first, rGO nanosheets are deposited on NF under mild hydrothermal conditions to increase the surface area. Subsequently, nanowalls of cobalt oxide are electro-deposited on rGO/Ni foam by applying cyclic-voltammetry (CV) under optimized conditions. Finally, for the synthesis of Co₃ O₄ @Co₃ S₄ nanocomposite, the nanostructure of Co₃ S₄ was fabricated from Co₃ O₄ nanowalls on rGO/NF by following an ordinary hydrothermal process through the sulfurization for the electrochemical application. The samples are characterized by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The obtained sample delivers a high capacitance of 13.34 F cm^-2 (5651.24 F g^-1 ) at a current density of 6 mA cm^-2 compared to the Co₃ O₄ /rGO/NF electrode with a capacitance of 3.06 F cm^-2 (1230.77 F g^-1 ) at the same current density. The proposed electrode illustrates the superior electrochemical performance such as excellent specific energy density of 85.68 W h Kg^-1 , specific power density of 6048.03 W kg^-1 and a superior cycling performance (86% after 1000 charge/discharge cycles at a scan rate of 5 mV s^-1 ). Finally, by using Co₃ O₄ @Co₃ S₄ /rGO/NF and the activated carbon-based electrode as positive and negative electrodes, respectively, an asymmetric supercapacitor (ASC) device was assembled. The fabricated ASC provides an appropriate specific capacitance of 79.15 mF cm^-2 at the applied current density of 1 mA cm^-2 , and delivered an energy density of 0.143 Wh kg^-1 at the power density of 5.42 W kg^-1 .

Supercapacitor electrode materials: addressing challenges in mechanism and charge storage

In recent years, rapid technological advances have required the development of energy-related devices. In this regard, Supercapacitors (SCs) have been reported to be one of the most potential candidates to meet the demands of human’s sustainable development owing to their unique properties such as outstanding cycling life, safe operation, low processing cost, and high power density compared to the batteries. This review describes the concise aspects of SCs including charge-storage mechanisms and scientific principles design of SCs as well as energy-related performance. In addition, the most important performance parameters of SCs, such as the operating potential window, electrolyte, and full cell voltage, are reviewed. Researches on electrode materials are crucial to SCs because they play a pivotal role in the performance of SCs. This review outlines recent research progress of carbon-based materials, transition metal oxides, sulfides, hydroxides, MXenes, and metal nitrides. Finally, we give a brief outline of SCs’ strategic direction for future growth.

Recent Developments in Polymer Nanocomposite-Based Electrochemical Sensors for Detecting Environmental Pollutants

The human population is generally subjected to diverse pollutants and contaminants in the environment like those in the air, soil, foodstuffs, and drinking water. Therefore, the development of novel purification techniques and efficient detection devices for pollutants is an important challenge. To date, experts in the field have designed distinctive analytical procedures for the detection of pollutants including gas chromatography/mass spectrometry and atomic absorption spectroscopy. While the mentioned procedures enjoy high sensitivity, they suffer from being laborious, expensive, require advanced skills for operation, and are inconvenient to deploy as a result of their massive size. Therefore, in response to the above-mentioned limitations, electrochemical sensors are being developed that enjoy robustness, selectivity, sensitivity, and real-time measurements. Considerable advancements in nanomaterials-based electrochemical sensor platforms have helped to generate new technologies to ensure environmental and human safety. Recently, investigators have expanded considerable effort to utilize polymer nanocomposites for building the electrochemical sensors in view of their promising features such as very good electrocatalytic activities, higher electrical conductivity, and effective surface area in comparison to the traditional polymers. Herein, the first section of this review briefly discusses the most important methods for polymer nanocomposites synthesis, such as in situ polymerization, direct mixing of polymer and nanofillers (melt-mixing and solution-mixing), sol-gel, and electrochemical methods. It then summarizes the current utilization of polymer nanocomposites for the preparation of electrochemical sensors as a novel approach for monitoring and detecting environmental pollutants which include heavy metal ions, pesticides, phenolic compounds, nitroaromatic compounds, nitrite, and hydrazine in different mediums. Finally, the current challenges and future directions for the polymer nanocomposites-based electrochemical sensing of environmental pollutants are outlined.

Polyaniline/reduced graphene oxide foams as metal-free cathodes for stable lithium-oxygen batteries

Lithium-oxygen batteries (LOBs) are considered as next-generation energy storage devices owing to their high-energy densities, yet they generally suffer from low actual specific capacity and poor cycle performance. To solve these issues, a range of electrocatalysts have been introduced in the cathode to reduce the overpotential during charge/discharge cycles and minimize unwanted side reactions. Due to relative high costs and limited reserves of noble metals and their compounds, it is important to develop low-cost and efficient metal-free electrocatalysts. Here, we report a simple method to prepare three-dimensional porous polyaniline (PANI)/reduced graphene oxide foams (PPGFs) with different PANI contents via a two-step self-assembly process. When these foams are tested as the cathode in LOBs, the device using the PPGF with 50% PANI content exhibits a discharge capacity up to 36 010 mAh g^-1 and an excellent cycling stability (260 cycles at 1000 mAh g^-1 and 500 cycles at 500 mAh g^-1), provid ing new insights into the design of next-generation metal-free cathodes for LOBs.

Construction of mesoporous carbon microsphere/polyaniline composites as high performance pseudocapacitive electrodes

Mesoporous carbon microspheres (MCMs), as a supercapacitor electrode material, have good gravimetric capacitance and rate performance; however, their low volumetric capacitance, which results from their low density, restricts their application as a micro power source. Herein, polyaniline was introduced into the channels of MCMs to achieve a synergistic effect and significantly increase the volumetric capacitance. MCMs with a high surface area and pore volume allowed the uniform dispersion of PANI within their channels in nanoscale dimensions. The interconnected carbon framework could provide excellent electrical conductivity and alleviate the structural collapse of PANI. Moreover, PANI could function not only as an active pseudocapacitive material that facilitated energy storage but also as a proton transport media that promoted a rapid protonation/deprotonation process during the redox reaction in the internal channels. As a result, PANI/MCM composites, even with a poor pore structure, delivered a high volumetric capacitance of 539F cm^-3 at 1 A g^-1 and an excellent rate performance of 83% at current densities ranging from 0.5 to 20 A g^-1. In addition, PANI/MCM composites exhibited good cycling stability, retaining 84% of the capacitance after 1000 charge/discharge cycles at 1 A g^-1, owing to the high mechanical strength of the MCMs. Therefore, this synthesis strategy could provide an efficient and scalable solution for the development of supercapacitor electrode materials.

Capacitance Enhancement of Hydrothermally Reduced Graphene Oxide Nanofibers

Nanocarbon materials present sp2-carbon domains skilled for electrochemical energy conversion or storage applications. In this work, we investigate graphene oxide nanofibers (GONFs) as a recent interesting carbon material class. This material combines the filamentous morphology of the starting carbon nanofibers (CNFs) and the interlayer spacing of graphene oxide, and exhibits a domain arrangement accessible for fast transport of electrons and ions. Reduced GONFs (RGONFs) present the partial removal of basal functional groups, resulting in higher mesoporosity, turbostratic stacking, and surface chemistry less restrictive for transport phenomena. Besides, the filament morphology minimizes the severe layer restacking shown in the reduction of conventional graphene oxide sheets. The influence of the reduction temperature (140-220 °C) on the electrochemical behaviour in aqueous 0.5 M H2SO4 of RGONFs is reported. RGONFs present an improved capacitance up to 16 times higher than GONFs, ascribed to the unique structure of RGONFs containing accessible turbostratic domains and restored electronic conductivity. Hydrothermal reduction at 140 °C results in the highest capacitance as evidenced by cyclic voltammetry and electrochemical impedance spectroscopy measurements (up to 137 F·g-1). Higher temperatures lead to the removal of sulphur groups and slightly thicker graphite domains, and consequently a decrease of the capacitance.

Recent Advances in Layer-by-Layer Assembled Conducting Polymer Based Composites for Supercapacitors

Development of well-designed electrodes is the key to achieve high performance supercapacitors. Therefore, as one of the effective methods, a layer-by-layer (LBL) approach is often fruitfully employed for the fabrication of electrode material. Benefiting from a tunable parameter of the LBL approach, this approach has paved a way to design a highly ordered nanostructured electrode material with excellent performance. Conducting polymers (CPs) are the frontrunners in supercapacitors and notably, the LBL assembly of CPs is attracting extensive attention. Therefore, this critical review covers a comprehensive discussion on the research progress of CP-based composites with special importance on the LBL approach predominately for supercapacitors. Following a brief discussion on supercapacitors and CPs, the most up-to-date techniques used in LBL are highlighted.

Bio-interfactants as double-sided tapes for graphene oxide

We present a versatile and highly substrate-independent approach for preparing multisandwich layers based on thermally reduced Graphene Oxide (rGO) which gets strongly attached by bio-interfactants using a layer-by-layer (LBL) aqueous dipping and rinsing process. The process allows for the deposition of homogeneous ultra-thin films (∼5.5 nm) in distinct surface topographies, thicknesses and compositions by varying the bio-interfactant layer(s). The layers formed on quartz or other semi conductive material are electrically conductive, flexible, and transparent. The here-developed approach could be applied for the fabrication of wearables, sensors, and antistatic transparent films.

Benzophenone assisted UV-activated synthesis of unique Pd-nanodendrite embedded reduced graphene oxide nanocomposite: a catalyst for C–C coupling reaction and fuel cell

In this work we report the use of benzophenone (BP) for the synthesis of a palladium (Pd) embedded on reduced graphene oxide (rGO) nanocomposite (Pd/rGO) using a simple aqueous solution and UV irradiation. The simple and facile evolution of thermodynamically unstable branched Pd(0) nanodendrites was achieved by BP photoactivation, circumventing the growth of more stable nanomorphologies. The synthesis of Pd(0)-embedded rGO nanosheets (PRGO-nd) was made possible by the simultaneous reduction of both the GO scaffold and PdCl₂ by introducing BP into the photoactivation reaction. The nanocomposites obtained in the absence of BP were common triangular and twinned Pd(0) structures which were also implanted on the rGO scaffold (PRGO-nt). The disparity in morphologies presumably occurs due to the difference in the kinetics of the reduction of Pd²⁺ to Pd⁰ in the presence and absence of the BP photoinitiator. It was observed that the PRGO-nd was composed of dense arrays of multiple Pd branches around nucleation site which exhibited (111) facet, whereas PRGO-nt showed a mixture of (100) and (111) facets. On comparing the catalytic efficiencies of the as-synthesized nanocatalysts, we observed a superiority in efficiency of the thermodynamically unstable PRGO-nd nanocomposite. This is due to the evolved active facets of the dendritic Pd(0) morphology with its higher surface area, as testified by Brunauer–Emmett–Teller (BET) analysis. Since both PRGO-nd and PRGO-nt contain particles of similar size, the dents and grooves in the structure are the cause of the increase in the effective surface area in the case of nanodendrites. The unique dendritic morphology of the PRGO-nd nanostructures makes them a promising material for superior catalysis, due to their high surface area, and the high density of surface atoms at their edges, corners, and stepped regions. We investigated the efficiency of the as-prepared PRGO-nd catalyst in the Suzuki–Miyaura coupling reaction and showed its proficiency in a 2 h reaction at 60 °C using 2 mol% catalyst containing 0.06 mol% active Pd. Moreover, the electrochemical efficiency for the catalytic hydrogen evolution reaction (HER) was demonstrated, in which PRGO-nd provided a decreased overpotential of 68 mV for a current density of 10 mA cm⁻², a small Tafel slope of 57 mV dec⁻¹ and commendable stability during chronoamperometric testing for 5 h.

Benzophenone photoinitiator aided synthesis of Pd-nanodendrite embedded rGO nanocatalyst possessing superior potential in C–C coupling reaction and fuel cell application.

Interfacial Engineered Polyaniline/Sulfur-Doped TiO2 Nanotube Arrays for Ultralong Cycle Lifetime Fiber-Shaped, Solid-State Supercapacitors

Fiber-shaped supercapacitors (FSCs) have great promises in wearable electronics applications. However, the limited specific surface area and inadequate structural stability caused by the weak interfacial interactions of the electrodes result in relatively low specific capacitance and unsatisfactory cycle lifetime. Herein, solid-state FSCs with high energy density and ultralong cycle lifetime based on polyaniline (PANI)/sulfur-doped TiO₂ nanotube arrays (PANI/S-TiO₂) are fabricated by interfacial engineering. The experimental results and ab initio calculations reveal that S doping can effectively promote the conductivity of titania nanotubes and increase the binding energy of PANI anchored on the electrode surface, leading to a much stronger binding of PANI on the surface of the electrode and excellent electrode structure stability. As a result, the FSCs using the PANI/S-TiO₂ electrodes deliver a high specific capacitance of 91.9 mF cm^-2, a capacitance retention of 93.78% after 12 000 charge-discharge cycles, and an areal energy density of 3.2 μW h cm^-2. Meanwhile, the all-solid-state FSC device retains its excellent flexibility and stable electrochemical capacitance even after bending 150 cycles. The enhanced performances of FSCs could be attributed to the large surface area, reduced ion diffusion path, improved electrical conductivity, and engineered interfacial interaction of the rationally designed electrodes.

Flexible Supercapacitors Based on Polyaniline Arrays Coated Graphene Aerogel Electrodes

Flexible supercapacitors(SCs) made by reduced graphene oxide (rGO)-based aerogel usually suffer from the low energy density, short cycle life and bad flexibility. In this study, a new, synthetic strategy was developed for enhancing the electrochemical performances of rGO aerogel-based supercapacitor via electrodeposition polyaniline arrays on the prepared ultralight rGO aerogel. The novel hybrid composites with coated polyaniline (PANI) arrays growing on the rGO surface can take full advantage of the rich open-pore and excellent conductivity of the crosslinking framework structure of 3D rGO aerogel and high capacitance contribution from the PANI. The obtained hybrid composites exhibit excellent electrochemical performance with a specific capacitance of 432 F g^-1 at the current density of 1 A g^-1, robust cycling stability to maintain 85% after 10,000 charge/discharge cycles and high energy density of 25 W h kg^-1. Furthermore, the flexible all-solid-state supercapacitor have superior flexibility and outstanding stability under different bending states from the straight state to the 90° status. The high-performance flexible all-solid-state SCs together with the lighting tests demonstrate it possible for applications in portable electronics.

Carbon nanotube/Co3O4 nanocomposites selectively coated by polyaniline for high performance air electrodes

We herein report the preparation of carbon nanotube (CNT)/Co₃O₄ nanocomposites selectively coated with polyaniline (PANI) via an electropolymerization method, for use as an effective electrode material for Li-air (Li-O₂) batteries. The Co₃O₄ catalyst attached to the CNTs facilitated the dissociation of reaction products and reduced the overpotential of the cells. As the carbon surface activates the side reactions, the PANI coating on the carbon surface of the electrode suppressed the side reaction at the electrode/Li₂O₂ and electrode/electrolyte interfaces, thus enhancing the cycle performance of the electrode. In addition, the catalytic activity of Co₃O₄ on the CNT/Co₃O₄ nanocomposites remained unaffected, as the Co₃O₄ surface was not covered with a PANI layer due to the nature of the electropolymerization method. Overall, the synergic effect of the PANI layer and the Co₃O₄ catalyst leads to a superior cyclic performance and a low overpotential for the electrode based on selectively PANI-coated CNT/Co₃O₄ nanocomposites.

Synthesis of well-dispersive 2.0 nm Pd–Pt bimetallic nanoclusters supported on β-cyclodextrin functionalized graphene with excellent electrocatalytic activity

Illustration for the preparation of the Pd–Pt@β-CD-RGO nanohybrid using an in situ reduction method.

Recent developments in the layer-by-layer assembly of polyaniline and carbon nanomaterials for energy storage and sensing applications. From synthetic aspects to structural and functional characterization

The construction of hybrid polymer-inorganic nanoarchitectures for electrochemical purposes based on the layer-by-layer assembly of conducting polymers and carbon nanomaterials has become increasingly popular over the last decade. This explosion of interest is primarily related to the increasing mastery in the design of supramolecular constructs using simple wet chemical approaches. Concomitantly, this continuous research activity paved the way to the rapid development of nanocomposites or "nanoblends" readily integrable into energy storage and sensing devices. In this sense, the layer-by-layer (LbL) assembly technique has allowed us to access three-dimensional (3D) multicomponent carbon-based network nanoarchitectures displaying addressable electrical, electrochemical and transport properties in which conducting polymers, such as polyaniline, and carbon nanomaterials, such as carbon nanotubes or nanographene, play unique roles without disrupting their inherent functions - complementary entities coexisting in harmony. Over the last few years the level of functional sophistication reached by LbL-assembled carbon-based 3D network nanoarchitectures, and the level of knowledge related to how to design, fabricate and optimize the properties of these 3D nanoconstructs have advanced enormously. This feature article presents and discusses not only the recent advances but also the emerging challenges in complex hybrid nanoarchitectures that result from the layer-by-layer assembly of polyaniline, a quintessential conducting polymer, and diverse carbon nanomaterials. This is a rapidly developing research area, and this work attempts to provide an overview of the diverse 3D network nanoarchitectures prepared up to now. The importance of materials processing and LbL integration is explored within each section and while the overall emphasis is on energy storage and sensing applications, the most widely-used synthetic strategies and characterization methods for "nanoblend" formation and performance evaluation are also presented.

Ultrastrong, Chemically Resistant Reduced Graphene Oxide-based Multilayer Thin Films with Damage Detection Capability

Multilayer thin films of graphene oxide (GO) and poly(vinylamine) (PVAm) were deposited via layer-by-layer assembly. Poly(vinylamine) pH was used to tailor film thickness and GO layer spacing. Graphene oxide concentration in the films was controlled through simple pH adjustment. Thermal reduction of the PVAm/GO multilayer thin films rendered them electrically conductive, which could be further tailored with PVAm pH. These reduced films also exhibited exceptionally high elastic modulus of 30 GPa and hardness of 1.8 GPa, which are among the highest of any graphene-filled polymer composite values ever reported. Cross-linking of these films with glutaraldehyde improved their chemical resistance, allowing them to survive strongly acidic or salty solutions. Additionally, scratches in the films can be instantaneously detected by a simple electrical resistance measurement. These films are promising for a variety of packaging and electronic applications.

The green reduction of graphene oxide

Graphene is an ultra-thin material, which has received broad interest in many areas of science and technology because of its unique physical, chemical, mechanical and thermal properties.