Electrochemical synthesis, characterization and electrochromic properties of indan and 1,3-benzodioxole-based poly(2,5-dithienylpyrrole) derivatives

4-(Trifluoromethoxy)phenyl-Containing Polymers as Promising Anodic Materials for Electrochromic Devices

Three 4-(trifluoromethoxy)phenyl-based polydithienylpyrroles (PTTPP, P(TTPP-co-DTC), and P(TTPP-co-DTP)) were synthesized electrochemically and their electrochromic behaviors were characterized. The introduction of electron withdrawing trifluoromethoxy unit in the side chain of polydithienylpyrroles (PSNS) decreases the HOMO and LUMO energy levels of PSNS. PTTPP film displays three various colors (grayish-yellow at 0 V, grayish-blue at 1.0 V, and bluish-violet at 1.4 V) from reduced to oxidized states. The optical contrast of PTTPP, P(TTPP-co-DTC), and P(TTPP-co-DTP) electrodes are 24.5% at 1050 nm, 49.0% at 916 nm, and 53.8% at 1302 nm, respectively. The highest η of the PTTPP electrode is 379.64 cm2 C−1 at 1050 nm. Three ECDs based on PTTPP, P(TTPP-co-DTC), or P(TTPP-co-DTP) as anodic film and PProDOT-Et2 as cathodic film were fabricated. PTTPP/PProDOT-Et2 ECD showed high transmittance change (35.7% at 588 nm) and high η (890.96 cm2·C−1 at 588 nm). P(TTPP-co-DTC)/PProDOT-Et2 and P(TTPP-co-DTP)/PProDOT-Et2 ECDs showed high transmittance change, rapid response time, adequate open circuit memory, and good electrochemical redox stability. Based on these findings, this work provides novel insights for appropriate design of high transmittance change and high efficient multi-colored electrochromic polymers.

Electrochromic Devices Based on Poly(2,6-di(9H-carbazol-9-yl)pyridine)-Type Polymer Films and PEDOT-PSS

2,6-Di(9H-carbazol-9-yl)pyridine (DiCP) was synthesized and its corresponding homopolymer (PDiCP) and copolymers (P(DiCP-co-CPDT), P(DiCP-co-CPDT2), P(DiCP-co-CPDTK), and P(DiCP-co-CPDTK2)) were synthesized electrochemically. The anodic copolymer with DiCP:cyclopentadithiophene ketone (CPDTK) = 1:1 feed molar ratio showed high transmittance change (ΔT%) and colouration efficiency (η), which were measured as 39.5% and 184.1 cm² C-1 at 1037 nm, respectively. Electrochromic devices (ECDs) were composed of PDiCP, P(DiCP-co-CPDT), P(DiCP-co-CPDT2), P(DiCP-co-CPDTK), and P(DiCP-co-CPDTK2) as anodically-colouring polymers, and poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonic acid) (PEDOT-PSS) as cathodically-colouring polymers. P(DiCP-co-CPDTK)/PEDOT-PSS ECD showed light silverish-yellow at 0.0 V, light grey at 0.7 V, grey at 1.3 V, light greyish blue at 1.7 V, and greyish blue at 2.0 V. Moreover, P(DiCP-co-CPDTK)/PEDOT-PSS ECD presented high ΔT (38.2%) and high η (633.8 cm² C-1) at 635 nm.

Impact of polyethyleneglycol addition on diffusion coefficients in binary ionic liquid electrolytes composed of dicationic ionic liquid and polyethyleneglycol

We conduct a comparative study of conductivity and diffusion coefficient of two dicationic ionic liquids (3,3'-(octane-1,8-diyl)bis(1-ethyl-3-imidazolium) bis(trifluoromethylsulfonyl)amide ([IMCI][TFSI], S1) and 3,3'-(2,2'-(ethane-1,2-diylbis(oxy))bis(ethane-2,1-diyl))bis(1-ethyl-3-imidazolium) bis(trifluoromethylsulfonyl)amide ([IMOI][TFSI], S2)) at various temperatures. The diffusion coefficients of cation and anion in ionic liquids are determined by using pulse gradient spin-echo nuclear magnetic resonance method. S2 shows lower viscosity, higher conductivity, and higher diffusion coefficient than those of S1. Moreover, the influence of polyethyleneglycol (PEG200, M_w  = 200) addition in PEG200/IL binary solutions is investigated. PEG200/S1 binary solutions show lower viscosity, higher conductivity, and higher diffusion coefficient than those of neat S1. The experimental molar conductivity (Λ) of neat IL and PEG200/IL binary solutions is lower than that of the calculated molar conductivity (Λ_NMR ) from pulse gradient spin-echo nuclear magnetic resonance method at various temperatures, indicating that not all the diffusion species belong to the ionic conduction. In other words, NMR diffusion measurements comprise charged and paired (without charge) ions. Copyright © 2017 John Wiley & Sons, Ltd.

Synthesis, characterization and electrochemistry of polycyclic fused aromatic pyrroles and their conjugated polymers

Two conjugated polymers, based on the polycyclic fused aromatic pyrrole-based compound naphthobipyrrole, are synthesized using electrochemical polymerization and chemical polymerization.

Poly(tris(4-carbazoyl-9-ylphenyl)amine)/Three Poly(3,4-ethylenedioxythiophene) Derivatives in Complementary High-Contrast Electrochromic Devices

A carbazole-based polymer (poly(tris(4-carbazoyl-9-ylphenyl)amine) (PtCz)) is electrosynthesized on an indium tin oxide (ITO) electrode. PtCz film displays light yellow at 0.0 V, earthy yellow at 1.3 V, grey at 1.5 V, and dark grey at 1.8 V in 0.2 M LiClO₄/ACN/DCM (ACN/DCM = 1:3, by volume) solution. The ΔT and coloration efficiency (η) of PtCz film are 30.5% and 54.8 cm²∙C-1, respectively, in a solution state. Three dual-type electrochromic devices (ECDs) are fabricated using the PtCz as the anodic layer, poly(3,4-ethylenedioxythiophene) (PEDOT), poly(3,3-dimethyl-3,4-dihydro-thieno[3,4-b][1,4]dioxepine) (PProDOT-Me₂), and poly(3,4-(2,2-diethylpropylenedioxy)thiophene) (PProDOT-Et₂) as the cathodic layers. PtCz/PProDOT-Me₂ ECD shows high ΔTmax (36%), high ηmax (343.4 cm²·C-1), and fast switching speed (0.2 s) at 572 nm. In addition, PtCz/PEDOT, PtCz/PProDOT-Me₂, and PtCz/PProDOT-Et₂ ECDs show satisfactory open circuit memory and long-term stability.

Three Carbazole-Based Polymers as Potential Anodically Coloring Materials for High-Contrast Electrochromic Devices

Three carbazole-based conjugated polymers (poly(3,6-di(2-thienyl)carbazole) (PDTC), poly(2,7-bis(carbazol-9-yl)-9,9-spirobifluorene) (PS2CBP), and poly(3,6-bis(N-carbazole)-N-ethylcarbazole) (PCEC)) are synthesized using electrochemical polymerization. The spectroelectrochemical studies indicate that the PDTC, PS2CBP, and PCEC films show reversible electrochromic behaviors in their redox states, and the PS2CBP film shows a distinct color transition with four various colors (gray at 0 V, grayish-green at 1.0 V, moss green at 1.2 V, and foliage green at 1.4 V). The maximum optical contrast of the PS2CBP and PCEC films is 39.83% at 428 nm and 32.41% at 420 nm, respectively, in an ionic liquid solution. Dual-type electrochromic devices (ECDs) that employ PDTC, PS2CBP, or PCEC film as an anodic layer, and PProDOT-Et₂ film as a cathodic layer, were constructed. The as-prepared PCEC/PProDOT-Et₂ ECD shows high optical contrast (38.25% at 586 nm) and high coloration efficiency (369.85 cm² C-1 at 586 nm), and the PS2CBP/PProDOT-Et₂ ECD shows high optical contrast (34.45% at 590 nm), good optical memory, and good long-term cycling stability.

Poly(3,3-dibenzyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine)/Platinum Composite Films as Potential Counter Electrodes for Dye-Sensitized Solar Cells

In this study, poly(3,3-dibenzyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine)/platinum composite films (PProDOT-Bz₂/Pt) were used as counter electrodes (CEs) in dye-sensitized solar cells (DSSCs). The composite films were prepared on fluorine-doped tin oxide (FTO) glass by radio frequency (RF) sputtering to deposit platinum (Pt) for 30 s. Afterwards, PProDOT-Bz₂ was deposited on the Pt⁻FTO glass via electrochemical polymerization. The electron transfer process of DSSCs was investigated using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The DSSCs with 0.05 C/cm² PProDOT-Bz₂-Pt composite films showed an open circuit voltage (Voc) of 0.70 V, a short-circuit current density (Jsc) of 7.27 mA/cm², and a fill factor (F.F.) of 68.74%. This corresponded to a photovoltaic conversion efficiency (η) of 3.50% under a light intensity of 100 mW/cm².

Applications of Three Dithienylpyrroles-Based Electrochromic Polymers in High-Contrast Electrochromic Devices

Three dithienylpyrroles (1-(4-(methylthio)phenyl)-2,5-di(thiophen-2-yl)-pyrrole (MPS), 1-(4-methoxyphenyl)-2,5-di(thiophen-2-yl)-pyrrole (MPO), and 4-(2,5-di(thiophen-2-yl)-pyrrol-1-yl)benzonitrile (ANIL)) were synthesized and their corresponding polydithienylpyrroles (PSNS) were electrosynthesized using electrochemical polymerization. Spectroelectrochemical studies indicated that poly(1-(4-(methylthio)phenyl)-2,5-di(thiophen-2-yl)-pyrrole) (PMPS) film was green, dark green, and brown in the neutral, oxidation, and highly oxidized state, respectively. The incorporation of a MPS unit into the PSNS backbone gave rise to a darker color than those of the MPO and ANIL units in the highly oxidized state. The PMPS film showed higher ΔTmax (54.47% at 940 nm) than those of the PMPO (43.87% at 890 nm) and PANIL (44.63% at 950 nm) films in an ionic liquid solution. Electrochromic devices (ECDs) employing PMPS, PMPO, and PANIL as anodic layers and poly(3,4-(2,2-diethypropylenedioxy)thiophene)(PProDOT-Et₂) as a cathodic layer were constructed. PMPO/PProDOT-Et₂ ECD showed the highest ΔTmax (41.13%) and coloration efficiency (674.67 cm²·C-¹) at 626 nm, whereas PMPS/PProDOT-Et2 ECD displayed satisfactory ΔTmax (32.51%) and coloration efficiency (637.25 cm²·C-¹) at 590 nm. Repeated cyclic voltammograms of PMPS/PProDOT-Et₂, PMPO/PProDOT-Et₂, and PANIL/PProDOT-Et₂ ECDs indicated that ECDs had satisfactory redox stability.

Effect of Ablation Rate on the Microstructure and Electrochromic Properties of Pulsed-Laser-Deposited Molybdenum Oxide Thin Films

Molybdenum trioxide (MoO₃) is a well-known electrochromic material. In the present work, n-type α-MoO₃ thin films with both direct and indirect band gaps were fabricated by varying the laser repetition (ablation) rate in a pulsed laser deposition (PLD) system at a constant reactive O₂ pressure. The electrochromic properties of the films are compared and correlated to the microstructure and molecular-level coordination. Mixed amorphous and textured crystallites evolve at the microstructural level. At the molecular level, using NMR and EPR, we show that the change in the repetition rate results in a variation of the molybdenum coordination with oxygen: at low repetition rates (2 Hz), the larger the octahedral coordination, and greater the texture, whereas at 10 Hz, tetrahedral coordination is significant. The anion vacancies also introduce a large density of defect states into the band gap, as evidenced by XPS studies of the valence band and supported by DFT calculations. The electrochromic contrast improved remarkably by almost 100% at higher repetition rates whereas the switching speed decreased by almost 6-fold. Although the electrochromic contrast and coloration efficiency were better at higher repetition rates, the switching speed, reversibility, and stability were better at low repetition rates. This difference in the electrochromic properties of the two MoO₃ films is attributed to the variation in the defect and molecular coordination states of the Mo cation.

High-Performance Electrochromic Devices Based on Poly[Ni(salen)]-Type Polymer Films

We report the application of two poly[Ni(salen)]-type electroactive polymer films as new electrochromic materials. The two films, poly[Ni(3-Mesalen)] (poly[1]) and poly[Ni(3-MesaltMe)] (poly[2]), were successfully electrodeposited onto ITO/PET flexible substrates, and their voltammetric characterization revealed that poly[1] showed similar redox profiles in LiClO4/CH3CN and LiClO4/propylene carbonate (PC), while poly[2] showed solvent-dependent electrochemical responses. Both films showed multielectrochromic behavior, exhibiting yellow, green, and russet colors according to their oxidation state, and promising electrochromic properties with high electrochemical stability in LiClO4/PC supporting electrolyte. In particular, poly[1] exhibited a very good electrochemical stability, changing color between yellow and green (λ = 750 nm) during 9000 redox cycles, with a charge loss of 34.3%, an optical contrast of ΔT = 26.2%, and an optical density of ΔOD = 0.49, with a coloration efficiency of η = 75.55 cm(2) C(-1). On the other hand, poly[2] showed good optical contrast for the color change from green to russet (ΔT = 58.5%), although with moderate electrochemical stability. Finally, poly[1] was used to fabricate a solid-state electrochromic device using lateral configuration with two figures of merit: a simple shape (typology 1) and a butterfly shape (typology 2); typology 1 showed the best performance with optical contrast ΔT = 88.7% (at λ = 750 nm), coloration efficiency η = 130.4 cm(2) C(-1), and charge loss of 37.0% upon 3000 redox cycles.

Applications of Tris(4-(thiophen-2-yl)phenyl)amine- and Dithienylpyrrole-based Conjugated Copolymers in High-Contrast Electrochromic Devices

Tris(4-(thiophen-2-yl)phenyl)amine- and dithienylpyrrole-based copolymers (P(TTPA-co-DIT) and P(TTPA-co-BDTA)) were electropolymerized on ITO electrode by applying constant potentials of 1.0, 1.1, and 1.2 V. Spectroelectrochemical investigations revealed that P(TTPA-co-DIT) film displayed more color changes than P(TTPA-co-BDTA) film. The P(TTPA-co-DIT) film is yellow in the neutral state, yellowish-green and green in the intermediate state, and blue (1.2 V) in highly oxidized state. The ∆T_max of the P(TTPA-co-DIT) and P(TTPA-co-BDTA) films were measured as 60.3% at 1042 nm and 47.1% at 1096 nm, respectively, and the maximum coloration efficiency (η) of P(TTPA-co-DIT) and P(TTPA-co-BDTA) films were calculated to be 181.9 cm²·C⁻¹ at 1042 nm and 217.8 cm²·C⁻¹ at 1096 nm, respectively, in an ionic liquid solution. Dual type electrochromic devices (ECDs) consisting of P(TTPA-co-DIT) (or P(TTPA-co-BDTA)) anodic copolymer, ionic liquid-based electrolyte, and poly(3,4-(2,2-diethylpropylenedioxy)thiophene) (PProDOT-Et₂) cathodic polymer were constructed. P(TTPA-co-BDTA)/PProDOT-Et₂ ECD showed high ΔT_max (48.1%) and high coloration efficiency (649.4 cm²·C⁻¹) at 588 nm. Moreover, P(TTPA-co-DIT)/PProDOT-Et₂ and P(TTPA-co-BDTA)/PProDOT-Et₂ ECDs displayed satisfactory optical memory and long term switching stability.