Chemical and Electrochemical Stability of Nitrogen and Sulphur Doped Mesoporous Carbons

H2O2 production at gas-diffusion cathodes made from agarose-derived carbons with different textural properties for acebutolol degradation in chloride media

The excessive cost, unsustainability or complex production of new highly selective electrocatalysts for H₂O₂ production, especially noble-metal-based ones, is prohibitive in the water treatment sector. To solve this conundrum, biomass-derived carbons with adequate textural properties were synthesized via agarose double-step pyrolysis followed by steam activation. A longer steam treatment enhanced the graphitization and porosity, even surpassing commercial carbon black. Steam treatment for 20 min yielded the greatest surface area (1248 m² g^-1), enhanced the mesopore/micropore volume distribution and increased the activity (E_1/2 = 0.609 V) and yield of H₂O₂ (40%) as determined by RRDE. The upgraded textural properties had very positive impact on the ability of the corresponding gas-diffusion electrodes (GDEs) to accumulate H₂O₂, reaching Faradaic current efficiencies of ~95% at 30 min. Acidic solutions of β-blocker acebutolol were treated by photoelectro-Fenton (PEF) process in synthetic media with and without chloride. In urban wastewater, total drug disappearance was reached at 60 min with almost 50% mineralization after 360 min at only 10 mA cm^-2. Up to 14 degradation products were identified in the Cl^--containing medium.

Sulfur Doping versus Hierarchical Pore Structure: The Dominating Effect on the Fe-N-C Site Density, Activity, and Selectivity in Oxygen Reduction Reaction Electrocatalysis

Nitrogen doping has been always regarded as one of the major factors responsible for the increased catalytic activity of Fe-N-C catalysts in the oxygen reduction reaction, and recently, sulfur has emerged as a co-doping element capable of increasing the catalytic activity even more because of electronic effects, which modify the d-band center of the Fe-N-C catalysts or because of its capability to increase the Fe-N_x site density (SD). Herein, we investigate in detail the effect of sulfur doping of carbon support on the Fe-N_x site formation and on the textural properties (micro- and mesopore surface area and volume) in the resulting Fe-N-C catalysts. The Fe-N-C catalysts were prepared from mesoporous carbon with tunable sulfur doping (0-16 wt %), which was achieved by the modulation of the relative amount of sucrose/dibenzothiophene precursors. The carbon with the highest sulfur content was also activated through steam treatment at 800 °C for different durations, which allowed us to modulate the carbon pore volume and surface area (1296-1726 m² g^-1). The resulting catalysts were tested in O₂-saturated 0.5 M H₂SO₄ electrolyte, and the site density (SD) was determined using the NO-stripping technique. Here, we demonstrate that sulfur doping has a porogenic effect increasing the microporosity of the carbon support, and it also facilitates the nitrogen fixation on the carbon support as well as the formation of Fe-N_x sites. It was found that the Fe-N-C catalytic activity [E_1/2 ranges between 0.609 and 0.731 V vs reversible hydrogen electrode (RHE)] does not directly depend on sulfur content, but rather on the microporous surface and therefore any electronic effect appears not to be determinant as confirmed by X-ray photoemission spectroscopy (XPS). The graph reporting Fe-N_x SD versus sulfur content assumes a volcano-like shape, where the maximum value is obtained for a sulfur/iron ratio close to 18, i.e., a too high or too low sulfur doping has a detrimental effect on Fe-N_x formation. However, it was highlighted that the increase of Fe-N_x SD is a necessary but not sufficient condition for increasing the catalytic activity of the material, unless the textural properties are also optimized, i.e., there must be an optimized hierarchical porosity that facilitates the mass transport to the active sites.

Highly Graphitized Fe-N-C Electrocatalysts Prepared from Chitosan Hydrogel Frameworks

The development of platinum group metal-free (PGM-free) electrocatalysts derived from cheap and environmentally friendly biomasses for oxygen reduction reaction (ORR) is a topic of relevant interest, particularly from the point of view of sustainability. Fe-nitrogen-doped carbon materials (Fe-N-C) have attracted particular interest as alternative to Pt-based materials, due to the high activity and selectivity of Fe-Nx active sites, the high availability and good tolerance to poisoning. Recently, many studies focused on developing synthetic strategies, which could transform N-containing biomasses into N-doped carbons. In this paper, chitosan was employed as a suitable N-containing biomass for preparing Fe-N-C catalyst in virtue of its high N content (7.1%) and unique chemical structure. Moreover, the major application of chitosan is based on its ability to strongly coordinate metal ions, a precondition for the formation of Fe-Nx active sites. The synthesis of Fe-N-C consists in a double step thermochemical conversion of a dried chitosan hydrogel. In acidic aqueous solution, the preparation of physical cross-linked hydrogel allows to obtain sophisticated organization, which assure an optimal mesoporosity before and after the pyrolysis. After the second thermal treatment at 900 °C, a highly graphitized material was obtained, which has been fully characterized in terms of textural, morphological and chemical properties. RRDE technique was used for understanding the activity and the selectivity of the material versus the ORR in 0.5 M H2SO4 electrolyte. Special attention was put in the determination of the active site density according to nitrite electrochemical reduction measurements. It was clearly established that the catalytic activity expressed as half wave potential linearly scales with the number of Fe-Nx sites. It was also established that the addition of the iron precursor after the first pyrolysis step leads to an increased activity due to both an increased number of active sites and of a hierarchical structure, which improves the access to active sites. At the same time, the increased graphitization degree, and a reduced density of pyrrolic nitrogen groups are helpful to increase the selectivity toward the 4e- ORR pathway.

Performance Loss of Activated Carbon Electrodes in Capacitive Deionization: Mechanisms and Material Property Predictors

Understanding the material property origins of performance decay in carbon electrodes is critical to maximizing the longevity of capacitive deionization (CDI) systems. This study investigates the cycling stability of electrodes fabricated from six commercial and two post-processed activated carbons. We find that the capacity decay rate of electrodes in half cells is positively correlated with the specific surface area and total surface acidity of the activated carbons. We also demonstrate that half-cell cycling stability is consistent with full cell desalination performance durability. Additionally, our results suggest that increase in internal resistance and physical pore blockage resulting from extensive cycling may be important mechanisms for the specific capacitance decay of activated carbon electrodes in this study. Our findings provide crucial guidelines for selecting activated carbon electrodes for stable CDI performance over long-term operation and insight into appropriate parameters for electrode performance and longevity in models assessing the techno-economic viability of CDI. Finally, our half-cell cycling protocol also offers a method for evaluating the stability of new electrode materials without preparing large, freestanding electrodes.

The Nanosized Dye Adsorbents for Water Treatment

Clean water is a vital element for survival of any living creature and, thus, crucially important to achieve largely and economically for any nation worldwide. However, the astonishingly fast trend of industrialization and population growth and the arisen extensive water pollutions have challenged access to clean water across the world. In this regard, 1.6 million tons of dyes are annually consumed. Thereof, 10%–15% are wasted during use. To decolorize water streams, there is an urgent need for the advanced remediation approaches involving utilization of novel materials and technologies, which are cost and energy efficient. Nanomaterials, with their outstanding physicochemical properties, can potentially resolve the challenge of need to water treatment in a less energy demanding manner. In this review, a variety of the most recent (from 2015 onwards) opportunities arisen from nanomaterials in different dimensionalities, performances, and compositions for water decolorization is introduced and discussed. The state-of-the-art research studies are presented in a classified manner, particularly based on structural dimensionality, to better illustrate the current status of adsorption-based water decolorization using nanomaterials. Considering the introduction of many newly developed nano-adsorbents and their classification based on the dimensionality factor, which has never been employed for this sake in the related literature, a comprehensive review will be presented.

Mesoporous Carbon with Different Density of Thiophenic-Like Functional Groups and Their Effect on Oxygen Reduction

The metal-support interactions between sulfur-doped carbon supports (SMCs) and Pt nanoparticles (NPs) were investigated, aiming at verifying how sulfur functional groups can improve the electrocatalytic performance of Pt NPs towards the oxygen reduction reaction (ORR). SMCs were synthetized, tailoring the density of sulfur functional groups, and Pt NPs were deposited by thermal reduction of Pt(acac)₂ . The extent of the metal-support interaction was proved by X-ray photoelectron spectroscopy (XPS) analysis, which revealed a strong electronic interaction, proportional to the density of sulfur defects, whereas XRD spectra provided evidence of higher strain in Pt NPs loaded on SMC. DFT simulations confirmed that the metal-support interaction was strongest in the presence of a high density of sulfur defects. The combination of microstrain and electronic effects resulted in a high catalytic activity of supported Pt NPs towards ORR, with linear correlations of the half-wave potential E_1/2 or the kinetic current j_k with the sulfur content in the support. Furthermore, a mass activity value (550 A g^-1 ) well above the United States Department of Energy target of 440 A g^-1 at 0.9 V (vs. reversible hydrogen electrode, RHE), was determined.

Using aminopyrine as a nitrogen-enriched small molecule precursor to synthesize high-performing nitrogen doped mesoporous carbon for catalyzing oxygen reduction reaction

With aminopyrine as a nitrogen-enriched small molecule precursor, a series of nitrogen doped carbon materials have been fabricated and explored as electrocatalysts for oxygen reduction reaction (ORR).

Green-assembly of three-dimensional porous graphene hydrogels for efficient removal of organic dyes

Herein, a facile and straightforward green-assembly approach was developed for preparation of nitrogen and sulphur co-doped three-dimensional (3D) graphene hydrogels (N/S-GHs) with the assistance of glutathione. Specifically, graphene oxide is reduced and assembled into 3D porous nanostructures with glutathione as the reducing agent and modifier for its intrinsic structure, along with the nitrogen and sulphur sources in the synthetic process. As expected, the as-obtained N/S-GHs demonstrated superior adsorption performances for organic dyes (e.g., methylene blue, malachite green, and crystal violet) in aqueous media. This work provides new insight for the green-assembly of 3D porous nanomaterials as adsorbent and their promising applications in water treatment.