Flexible graphene oxide−wrapped SnO2 hollow spheres with high electrochemical sensing performance in simultaneous determination of 4−aminophenol and 4−chlorophenol

Fast and effective assessment of 4-chlorophenol as a persistent organic pollutant (POP) using a multi-walled carbon nanotube-modified screen-printed carbon electrode (C/MWCNT-COOH/SPCE)

In this study, a rapid, precise, and targeted electroanalytical method was developed for the trace determination of 4-chlorophenol (4-CP). The study reports the use of cyclic voltammetry (CV) to characterize the electrochemical response of 4-CP and the optimization of differential pulse voltammetry (DPV) settings for its sensitive quantification. Screen-printed carbon electrodes (SPCEs) were selected for the sensitive detection of 4-CP using DPV. The incorporation of multi-walled carbon nanotubes functionalized with carboxyl groups (MWCNT-COOH) as a modifier on the working SPCE significantly enhances the electrode's performance, resulting in a 5-fold increase in sensitivity compared to that of the unmodified SPCE. Under optimal conditions, oxidation peak current exhibited a detection limit of 9.2 nM and was proportional to 4-CP concentration in the range of 0.01-1.3 μM. Additionally, the constructed sensor demonstrated high stability, high selectivity, good reproducibility, and excellent feasibility. These findings suggest that the C/MWCNT-COOH/SPE offers a simple, rapid, and cost-effective method for the prospective online assessment of 4-CP in various samples with different matrices.

A novel sensor based on Ti3C2 MXene/Co3O4/carbon nanofibers composite for the sensitive detection of 4-aminophenol

A novel, sensitive Ti3C2 MXene/Co3O4/carbon nanofibers (Ti3C2 MXene/Co3O4/CNFs) composite was synthesized via a HF exfoliating Ti3AlC2 strategy, followed by doping Co3O4 and Ti3C2 MXene into the CNFs via a combination electrospinning and thermal annealing process. Ti3C2 MXene/Co3O4/CNFs composite exhibits higher catalytic effect, conductivity, chemical stability, and electrochemical performance than Co3O4 and Ti3C2 MXene in electrochemical impedance, differential pulse stripping voltammetry, chronocoulometry, and cyclic voltammetry tests. This Ti3C2 MXene/Co3O4/CNFs hybrid modified electrode provides fast analysis of 4-aminophenol (4-AP) with ultrahigh sensitivity, enhanced reproducibility and strong anti-interference capability. Furthermore, the level of 4-AP was quantified by this electrode with a wide linear range from 0.5 to 150 μM (R2 > 0.99) and a low detection limit about 0.018 μM was achieved. Finally, the fabricated electrode was used for fast and sensitive analysis of 4-AP spiked in tap water and blood serum samples. This work presents the new Ti3C2 MXene/Co3O4/CNFs electrode provides a platform for 4-AP monitoring and has the advantages of high selectivity, accuracy, simplicity, and rapid analysis.

A carbon based-screen-printed electrode amplified with two-dimensional reduced graphene/Fe3O4 nanocomposite as electroanalytical sensor for monitoring 4-aminophenol in environmental fluids

The analysis water pollutants are so important strategy for investigation of water quality. On the other hand, 4-aminophenol is known as a hazardous and high-risk compound for humans, and its detection and measurement is very important for investigating the quality of surface and groundwater. In this study, graphene/Fe₃O₄ nanocomposite was synthesized by a simple chemical method and characterized by EDS and TEM methods and results showed Nano spherical shape of Fe₃O₄ nanoparticle with diameter about 20 nM decorated at surface of 2D reduce graphene nanosheet (2D-rG-Fe₃O₄). The 2D-rG-Fe₃O₄ was used as excellent catalyst at surface of carbon-based screen-printed electrode (CSPE) and used as electroanalytical sensor in monitoring and determination of 4-aminophenol in waste water sample. The results confirmed improving ∼4.0 times in oxidation signal and reducing 120 mV in oxidation potential of 4-aminophenol at surface of 2D-rG-Fe₃O₄/CSPE compare to CSPE, respectively. The electrochemical investigation showed pH dependence behavior with equal value of electron and proton for -aminophenol at surface of 2D-rG-Fe₃O₄/CSPE. Using square wave voltammetry method (SWV), the 2D-rG-Fe₃O₄/CSPE successfully monitored 4-aminophenol in the concentration range 1.0 nM-200 μM. Finally, 2D-rG-Fe₃O₄/CSPE monitored 4-aminophenol in the different environmental fluids such as urban waste water, industrial waste water and river samples with recovery range 97.2%-104.3% that confirm powerful ability of 2D-rG-Fe₃O₄/CSPE as analytical tool.

State-of-art advances on removal, degradation and electrochemical monitoring of 4-aminophenol pollutants in real samples: A review

p_Aminophenol, namely 4-aminophenol (4-AP), is an aromatic compound including hydroxyl and amino groups contiguous together on the benzene ring, which are suitable chemically reactive, amphoteric, and alleviating agents in nature. Amino phenols are appropriate precursors for synthesizing oxazoles and oxazines. However, since the toxicity of aniline and phenol can harm human and herbal organs, it is essential to improve a reliable technique for the determination of even a trace amount of amino phenols, as well as elimination or (bio)degradation/photodegradation of it to protect both the environment and people's health. For this purpose, various analytical methods have been suggested up till now, including spectrophotometry, liquid chromatography, spectrofluorometric and capillary electrophoresis, etc. However, some drawbacks such as the requirement of complex instruments, high costs, not being portable, slow response time, low sensitivity, etc. prevent them to be employed in a wide range and swift in-situ applications. In this regard, besides the efforts such as (bio)degradation/photodegradation or removal of 4-AP pollutants from real samples, electroanalytical techniques have become a promising alternative for monitoring them with high sensitivity. In this review, it was aimed to emphasize and summarize the recent advances, challenges, and opportunities for removal, degradation, and electrochemical sensing 4-AP in real samples. Electroanalytical monitoring of amino phenols was reviewed in detail and explored the various types of electrochemical sensors applied for detecting and monitoring in real samples. Furthermore, the various technique of removal and degradation of 4-AP in industrial and urban wastes were also deliberated. Moreover, deep criticism of multifunctional nanomaterials to be utilized as a catalyst, adsorbent/biosorbent, and electroactive material for the fabrication of electrochemical sensors was covered along with their unique properties. Future perspectives and conclusions were also criticized to pave the way for further studies in the field of application of up-and-coming nanostructures in environmental applications.

Quick and accurate determination of hazardous phenolic compounds using CaCu2O3 nanorods based electrochemical sensor

In the present work, we report the fabrication of a novel electrochemical sensor based on nanostructured CaCu₂O₃ as electrode material for the simultaneous determination of 2-Aminophenol (o-AP), 2-Chlorophenol (o-CP) and 2-Nitrophenol (o-NP). Nanorods-shaped CaCu₂O₃ have been synthesized by chemical precipitation method and characterized by powder X-ray diffraction (XRD), X-ray photo-electron microscopy (XPS), field emission electron microscopy (FESEM) and high-resolution transmission electron microscopy (HRTEM). Glassy carbon electrodes (3 mm diameter) have been modified using CaCu₂O₃ nanorods by drop-casting method. Cyclic voltammetry (CV) studies at CaCu₂O₃/GCE exhibited excellent electrochemical behaviours towards the oxidation of 2-AP, 2-CP and 2-NP at different potentials well separated from each other. The CaCu₂O₃/GCE displayed the lowest detection limits of 5.74 nM (0.626 ppb), 1.38 nM (0.177 ppb) and 1.03 nM (0.143 ppb) for 2-AP, 2-CP and 2-NP respectively over wide measurable linear ranges of 175 nM-68 μM (2-AP), 50 nM-90 μM (2-CP) and 25 nM-32 μM (2-NP). Cyclic stability studies showed a loss of 7%, 13% and 14% from initial current responses after conducting 100 cycles of CV for 2-AP, 2-CP and 2-NP in PBS (pH 7.0) which indicated the excellent stability of the fabricated electrode. Reproducibility studies of six different CaCu₂O₃/GCEs exhibited good recoveries in the order of 3.23% (2-AP), 3.54% (2-CP) and 2.46% (2-NP) respectively. The fabricated electrode with excellent sensitivity, stability and reproducibility has been successfully applied for the determination of 2-AP, 2-CP and 2-NP simultaneously in tap water and agricultural water samples. Selectivity studies carried out on CaCu₂O₃/GCE revealed its ability to detect 4-aminophenol and 4-nitorphenol at different oxidation potentials. High performance liquid chromatography (HPLC) studies have been carried out to validate the practical utility of the fabricated sensor.

Iodine/iodide-doped polymeric nanospheres for simultaneous voltammetric detection of p-aminophenol, phenol, and p-nitrophenol

A sensor was developed for the first time based on polydopamine nanospheres doped with I₂, I^-, and IO₃^- species (PDA-Iodine), to determine the concentration of p-aminophenol (p-AP), phenol (Ph), and p-nitrophenol (p-NP) simultaneously. These polymeric nanospheres were successfully characterized using a variety of techniques including field emission scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared, Raman spectroscopy, and X-ray diffraction analysis. A carbon paste electrode was modified with the PDA-Iodine (CPE/PDA-Iodine). Because of the electrocatalytic activity of DA/DQ, I₂ and I^- species (in the structure of PDA-Iodine), CPE/PDA-Iodine shows enhancement in the electrooxidation peak currents as well as slight negative shift in peak potentials of p-AP, Ph, and p-NP compared with a bare carbon paste electrode. Under optimal experimental conditions, the linear calibration plots are linear in the ranges 0.5-120 μM for p-AP, 0.7-120 μM for Ph, and 1.0-100 μM for p-NP with limits of detection of 30, 40, and 80 nM for p-AP, Ph, and p-NP, respectively (S/N = 3). To prove the performance of the method, the repeatability of the signals of CPE/PDA-Iodine was evaluated and the RSD values obtained were 2.9%, 3.2%, and 3.1% for p-AP (45 µM), Ph (40 µM), and p-NP (40 µM), respectively. The CPE/PDA-Iodine is a promising new sensor for sensing p-AP, Ph, and p-NP simultaneously in tap and river water sample and the values of recoveries for spiked samples were in the range 94.0-104.4%.

Fabrication of novel three-dimensional Fe3O4-based particles electrodes with enhanced electrocatalytic activity for Berberine removal

Reasonable design of three-dimensional (3D) catalytic particle electrodes (CPEs) is crucial for achieving efficient electrocatalytic oxidation of organic pollutants. Herein, the novel Fe₃O₄/SnO₂/GO (FO/SO/GO) particle electrode has been developed and serviced to the 3D electrocatalytic berberine hydrochloride oxidation system with DSA (RuO₂-IrO₂-SnO₂/Ti) electrode as anode and GDE (gas diffusion electrode) electrode as the cathode. Compared with 2D systems and other CPEs, FO/SO/GO electrode shows excellent electrocatalytic activity and remarkable stability for BH removal, that is, the removal rate of BH is 94.8% within 90 min, and the rate constant is 0.03095 min^-1. More importantly, after five cycles, the ternary composite still maintains a strong ability to oxidize pollutants. The structural characterization and electrochemical measurement further uncover that the electron transfer ability and electrocatalytic oxidation efficiency are highly dependent on the surface structure regulation of CPEs. Furthermore, the quenching experiments show that hydroxyl radicals are the main active species in the 3D electro-Fenton (EF) system, which can oxidize BH molecules adsorbed on the surface of GO to CO₂, H₂O, or other products. The results could potentially provide new insights for designing and fabricating more stable and efficient 3D CPEs electrocatalytic removal of organic pollutants in the future.

Novel SnO2@ZIF-8/gC3N4 nanohybrids for excellent electrochemical performance towards sensing of p-nitrophenol

Herein, a novel synthetic strategy has been proposed to prepare engineered SnO₂@ZIF-8/gC₃N₄ nanohybrids for electrochemical sensing of p-nitrophenol (p-NP). The electrochemical properties were investigated using cyclic voltammetry (CV), chronoamperometry (CA), and differential pulse voltammetry (DPV). The developed nanohybrid sensor displayed an excellent electrochemical performance towards sensing of p-NP with a detection limit of 0.565 μM. The sensitivity of the prepared nanohybrid was found to be 2.63 μAcm^-2μM^-1. Moreover, the newly fabricated sensor exhibited remarkable selectivity (over tenfold excess) in the presence of common interferents. The simultaneous detection of isomers of nitrophenol is difficult using the developed sensor. However, other common interferents, such as phenol and aminophenol have negligible effects on the sensitivity of SnO₂@ZIF-8/gC₃N₄ towards the detection of p-nitrophenol. Further, the newly developed sensor showed consistency of sensing response up to 30 days. Thus, implementation of SnO₂@ZIF-8/gC₃N₄ nanohybrids as a p-NP electrochemical sensor offers the advantages of simplicity, selectivity, and stability.

Interference-free electrocatalysis of p-chloro meta xylenol (PCMX) on uniquely designed optimized polymeric nanohybrid of P(EDOT-co-OPD) and fMWCNT modified glassy carbon electrode

p-Chloro-meta-Xylenol (PCMX) is an environmentally hazardous phenolic compound having biocidal and antiseptic activity. Very few research publications addressed monitoring this contaminant. This paper presents a rapid sensing system to quantify it in waste water samples. The electrochemical activity of PCMX was exploited through a unique polymeric nanocomposite modified transducer for its quantification. Poly[(3,4-Ethylenedioxythiophene)-co-(o-phenylenediamine)] [P(EDOT-co-OPD)] was deposited through one-step electropolymerization technique on the glassy carbon electrode (GCE) modified by functionalized multi-wall carbon nanotubes (fMWCNTs). An optimized combination of these constituents was evaluated using response surface methodology (RSM) based Box-Behnken experimental design. This maximized the response for PCMX using differential pulse voltammetry (DPV). The sensing matrix was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The structural and morphological study of the modified film was conducted by Fourier transform-infrared spectroscopy (FT-IR), Raman spectroscopy, scanning electron microscopy (SEM), and field emission scanning electron microscope (FESEM). The anodic peak current could be read from a wide range of 0.5-225 μM calibration curve with a detection limit of 0.2545 μmol L^-1. Interestingly this work did not use any biomaterial in the modification but achieved interference-free response with excellent selectivity, sensitivity (0.4668 μA μM^-1 cm^-2), reproducibility (RSD = 2.2%), and repeatability. The sensing platform showed good stability (85.7%) of 3 months even after 150 times repetitive use. Its applicability for real samples was established by good correlation with standard methods.

A sensitive sensor based on MOFs derived nanoporous carbons for electrochemical detection of 4-aminophenol

A novel electrochemical sensor based on zinc oxide/nitrogen doped porous carbons (ZnO/NPC) modified electrode has been constructed for detecting 4-aminophenol (4-AP). The ZnO/NPC material was synthesized by one-step carbonization of MOF-5-NH₂. The modified glassy carbon electrode (ZnO/NPC/GCE) holds excellent electrocatalytic activity toward 4-AP, with a sensitivity of about 31.02 μA/μM/cm². Under optimal conditions, its oxidation peak current increases linearly with the increasing concentration of 4-AP (from 5 to 120 μmol/L), and the detection limits is 0.014 μmol/L (S/N = 3). Furthermore, favorable selectivity, superior reproducibility and outstanding stability have been achieved. The ZnO/NPC/GCE has been applied in detecting 4-AP in industrial waste water and achieved positive results with the recovery of 4-AP ranging from 94.02% to 107.7%, which confirms that this sensor is a reliable platform for the detection of 4-AP in waste water.

Label-free electrochemical aptasensor for progesterone detection in biological fluids

A label-free electrochemical progesterone (P4) aptasensor was successfully developed by covalently immobilizing NH₂-functionalized P4-specific aptamer on the electrode surface. The NiO-Au hybrid nanofibers were synthesized by the electrospinning technique. GQDs-NiO-AuNFs nanocomposite was prepared by dispersing of electrospun NiO-AuNFs in the as-synthesized graphene quantum dots (GQDs) solution and stirring for 24 h. Novel GQDs-NiO-AuNFs nano-architecture in combination with functionalized multiwalled carbon nanotubes (f-MWCNTs) were further utilized to modify screen printed carbon electrode (SPCE) in order to construct an effective immobilization matrix with plenty of carboxylic functional groups. The stepwise assembly process of the designed aptasensor was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The aptamer-progesterone complex formation led to a hindered electron transfer reaction on the sensing interface, which decreased the redox probe peak current. Based on of this, progesterone could be quantitatively detected by monitoring the decrease of differential pulse voltammetric (DPV) responses of [Fe(CN)₆]^3-/4- peak current with increasing the progesterone concentration. Under optimized experimental parameters, the aptasensor exhibited a dynamic concentration range from 0.01 to 1000 nM and a detection limit of 1.86 pM. The proposed aptasensor was successfully employed for the determination of progesterone in human serum samples and pharmaceutical formulations.

Simultaneous detection of paracetamol and 4-aminophenol at nanomolar levels using biocompatible cysteine-substituted phthalocyanine

Extension of the conjugation and biocompatibility of the phthalocyanine molecule is expected to improve its stability and interaction with bio-molecules without any fouling.

Significant enhancement in the electrochemical determination of 4-aminophenol from nanoporous gold by decorating with a Pd@CeO2 composite film

An electrode based on Pd@CeO₂ nanocomposite-decorated nanoporous gold on a carbon fiber paper was achieved, which demonstrated excellent performance in 4-aminophenol determination.

Facile SrO nanorods: an efficient and alternate detection approach for the selective removal of 4-aminophenol towards environmental safety

In this approach, it is introduced a new route to fabricate a reliable and reproducible wet-chemically prepared SrO NRs fabricated glassy carbon electrode sensor probe by electrochemical method for the detection of phenolic derivatives for the safety of environmental and healthcare fields in broad scales.

A Facile In-Situ Development of L-Valine Film onto the Surface of Carbon Paste Electrode Towards the Detection of Environmentally Hazardous 4-Amino Phenol

A small scale of environmentally hazardous 4-aminophenol can show significant impact on human health. Hence, in the present work, we have designed L-Valine film (Vf) modified carbon paste electrode (Vf/CPE) for the determination of 4-aminophenol. Herein, a facile in-situ L-Valine film was developed by electrochemical polymerization method onto the surface of bare carbon paste electrode (BCPE) with the help of cyclic voltammetry (CV) technique. A two-folds of electrochemical peak current enhancement was achieved at Vf/CPE in comparison with BCPE towards the determination of 4-aminophenol in optimum pH 7.0 of phosphate buffer solution (PBS). This was achieved due to the large surface area and conductive nature of Vf/CPE, which was concluded through the techniques of cyclic voltammetry and electrochemical impedance spectroscopy (EIS). The effect of pH of buffer and scan rate studies were successfully studied. Morphological changes of BCPE and Vf/CPE was studied with the help of scanning electron microscopy (SEM). The formation of Vf on CPE was also analyzed by Fourier transform infrared (FTIR) spectra. Under the optimized conditions, the limit of detection (LOD) and limit of quantification (LOQ) values of 4-aminophenol were estimated with the aid of chronoamperometry (CA) technique and was found to be 9.8 μM and 32 μM, respectively. Finally the proposed method was found to have satisfactory repeatability, reproducibility and stability results with low relative standard deviation (RSD) values.