Electrochemical behavior of thiosalicylic acid at γ-Fe2O3 nanoparticles and clay composite carbon electrode

Electrochemical detection of oxytetracycline employing sugarcane carbon modified graphite electrode

The present study used CeO2-Co3O4 quantum dots@porous carbon/multiwalled carbon nanotube (CeO2-Co3O4 QDs@PC/MWCNT/GE) composites to modify graphite electrodes to fabricate high-sensitivity electrochemical sensors to detect the presence of oxytetracycline (OTC). The quantum dots were made from waste sugarcane bagasse. The electrochemical analysis demonstrated the superior electrochemical performance of CeO2-Co3O4 QDs@PC/MWCNT/GE, with a peak current density of 1.276 mA/cm2. Electrochemical impedance spectroscopy (EIS) revealed lower impedance values for CeO2-Co3O4 QDs@PC/MWCNT/GE compared to other electrodes, indicating enhanced conductivity. The modified electrode exhibited an enlarged electrochemically active area, with values of 0.602 cm2, almost seven times that of the bare graphite electrode (0.079 cm2). The results showed that the CeO2-Co3O4 QDs@PC/MWCNT/GE had excellent performance for OTC detection, and its linear calibration range was 1.007 × 10-8 to 2.04 × 10-7 M (i.e., 0.005-0.1 ppm) and 1.007 × 10-6 to 1.209 × 10-4 M (i.e., 0.5-60 ppm). The limit of detection and limit of quantification were 1.23 nM (0.61 ppb) and 4.09 nM (2.03 ppb) (S/N = 3), respectively. The electrode demonstrated long-term stability for up to 7 weeks. This method provides a new way to prepare electrochemical sensors for OTC detection.

Electrochemical sensor based on a ZnO-doped graphitized carbon for the electrocatalytic detection of the antibiotic hydroxychloroquine. Application: tap water and human urine

Abstract

In December 2019, the world experienced a new coronavirus, SARS-CoV-2, causing coronavirus disease 2019 originating from Wuhan.The virus has crossed national borders and now affects more than 200 countries and territories. Hydroxychloroquine has been considered as a drug capable of treating COVID-19. The objective of this work is to establish a simple platform for electrocatalytic detection of hydroxychloroquine in human urine samples and pharmaceutical samples (tablets) using a ZnO@CPE sensor constructed by simple and inexpensive hydrothermal methods using a square wave voltammetry method. The best results are obtained in a PBS electrolyte with irreversible behavior of the hydroxychloroquine complement and controlled by diffusion coupled with absorption phenomena. The ZnO@CPE shifts the oxidation potential of hydroxychloroquine with the formation of a single very intense peak at the position of Epa = 0.5 V/(vs Ag/AgCl) with a shift is ΔEp = 0.1 V(vs Ag/AgCl) compared to the unmodified electrode. The obtained ZnO@CPE hybrid nanocomposite was characterized by different techniques and showed excellent electrocatalytic activity and higher active surface area compared to the bare carbon paste electrode. Under the optimized experimental conditions, the ZnO@CPE sensor showed good analytical performance for the determination of trace amounts of hydroxychloroquine, a wide linearity range from 10^-3 M to 0.8 × 10^-6 M with a very low detection limit in the range of 1.33 × 10^-7 M, satisfactory selectivity, acceptable repeatability and reproducibility. The calculated recovery and coefficient of variation for the two samples analyzed are very satisfactory, ranging from 97.6 to 102% and 1.2 to 2.3% respectively. The proposed applied method and the fabricated sensor offer the possibility to analyze traces of hydroxychloroquine in real human urine and water samples.

Graphical abstract

Strategy for the electro-oxidation reaction of hydroxychloroquine on the electro-catalytic surface of the ZnO@Carbon graphite electrode and real-time detection of hydroxychloroquine.

An Insight into Carbon Nanomaterial-Based Photocatalytic Water Splitting for Green Hydrogen Production

At present, the energy shortage and environmental pollution are the burning global issues. For centuries, fossil fuels have been used to meet worldwide energy demand. However, thousands of tons of greenhouse gases are released into the atmosphere when fossil fuels are burned, contributing to global warming. Therefore, green energy must replace fossil fuels, and hydrogen is a prime choice. Photocatalytic water splitting (PWS) under solar irradiation could address energy and environmental problems. In the past decade, solar photocatalysts have been used to manufacture sustainable fuels. Scientists are working to synthesize a reliable, affordable, and light-efficient photocatalyst. Developing efficient photocatalysts for water redox reactions in suspension is a key to solar energy conversion. Semiconductor nanoparticles can be used as photocatalysts to accelerate redox reactions to generate chemical fuel or electricity. Carbon materials are substantial photocatalysts for total WS under solar irradiation due to their high activity, high stability, low cost, easy production, and structural diversity. Carbon-based materials such as graphene, graphene oxide, graphitic carbon nitride, fullerenes, carbon nanotubes, and carbon quantum dots can be used as semiconductors, photosensitizers, cocatalysts, and support materials. This review comprehensively explains how carbon-based composite materials function as photocatalytic semiconductors for hydrogen production, the water-splitting mechanism, and the chemistry of redox reactions. Also, how heteroatom doping, defects and surface functionalities, etc., can influence the efficiency of carbon photocatalysts in H2 production. The challenges faced in the PWS process and future prospects are briefly discussed.

Structured clay minerals-based nanomaterials for sustainable photo/thermal carbon dioxide conversion to cleaner fuels: A critical review

In efforts to achieve a sustainable development goal, the utilization of CO₂ to generate renewable fuels is promising, as it is a sustainable technology that provides affordable and clean energy. To realize the production of renewable green fuels, a proficient and low-cost technology is required. Using photo/thermal catalytic process, the goal of sustainable CO₂ hydrogenation can be achieved. There have been several types of catalysts under exploration, however, they are expensive with limited availability. In the current development, green materials such as mineral clays are emerging as cocatalyst/supports for CO₂ hydrogenation. Clays are bestowed with various beneficial properties such as a large surface area, high porosity, abundant basic sites, excellent thermal stability and chemical corrosion resistance. Clays are promising materials that can drastically reduce the cost in catalyst preparation, partially fulfil the energy demand and reduce greenhouse gas emission. This review aims to focus on the various types of clays and their applications in the field of photo/thermal CO₂ hydrogenation to renewable fuels. Firstly, the classifications of clays are provided, whereby they can be differentiated based on their silicate layers, namely 1:1 and 2:1 type clay and their properties are thoroughly discussed to provide advantages and applications. The applications of various clays such as kaolinite, halloysite, montmorillonite, attapulgite, saponite and volkonskoite for CO₂ hydrogenation reactions are systematically discoursed. In addition, various approaches to improve the capability of raw clays as catalyst support are critically discussed, which include thermal treatment, exfoliation, acid-leaching and pillaring approaches. A critical discussion regarding the engineering aspects to further enhance clay-based catalyst for CO₂ hydrogenation are further disclosed. In short, clays are freely available materials that can be found in abundance. However, there are many more different types of natural green clays that have not been studied and explored in various energy applications.

Gas sensing materials roadmap

Gas sensor technology is widely utilized in various areas ranging from home security, environment and air pollution, to industrial production. It also hold great promise in non-invasive exhaled breath detection and an essential device in future internet of things. The past decade has witnessed giant advance in both fundamental research and industrial development of gas sensors, yet current efforts are being explored to achieve better selectivity, higher sensitivity and lower power consumption. The sensing layer in gas sensors have attracted dominant attention in the past research. In addition to the conventional metal oxide semiconductors, emerging nanocomposites and graphene-like two-dimensional materials also have drawn considerable research interest. This inspires us to organize this comprehensive 2020 gas sensing materials roadmap to discuss the current status, state-of-the-art progress, and present and future challenges in various materials that is potentially useful for gas sensors.

PARAFAC and MCR-ALS approaches to the pKa determination of benzoic acid and its derivatives

In general, the identification of biological activities of a molecule requires the observation of its physicochemical characteristics with its molecular interactions in an organism. The acid-base ionization constant (or pKa) is one of the key parameters that shows the physicochemical behaviors of molecules used in pharmaceuticals, foods, cosmetics etc. Therefore, the development of new methods (or approaches) is necessary to get simple, rapid, inexpensive and reliable determination of the acidity constants of active and inactive ingredients used in commercial products. In this paper, new UV spectroscopic methods were developed for the first time, by applying parallel factor analysis (PARAFAC) and multivariate curve resolution-alternating least squares (MCR-ALS) to the pH-UV spectral data arrays for determining the pKa values of benzoic acid and its five derivatives (4-fluorobenzoic acid, thiosalicylic acid, anthranilic acid, phthalic acid, 4-aminobenzoic acid). The pH profiles obtained by the PARAFAC and MCR-ALS decomposition of the pH-UV data arrays were used for the quantitative estimation of the acid-base ionization constants for the investigated compounds without classical titration procedure. We concluded that the proposed PARAFAC and MCR-ALS provided us an opportunity for simple and rapid pKa determination of relevant compounds, which have functional importance in pharmaceutical and food industries.

2D/2d heterojunction of MoS2/g-C3N4 nanoflowers for enhanced visible-light-driven photocatalytic and electrochemical degradation of organic pollutants

Photodegradation of toxic pollutants is a promising approach to deal with wastewater management. In this regard, MoS₂/g-C₃N₄ (MSC) derived composites with varying weight-ratios were prepared via fast (30 min) one step microwave-assisted method. The materials were characterized by XRD, XPS, EDS, FESEM and HRTEM to validate their flower-like and sheet-like morphologies. The PL and UV-vis DRS spectra exhibited low recombination-rate and band-gap (1.7 eV), which is appropriate for an effective visible-light degradation. Photocatalytic performance of the catalysts was analyzed by investigating the degradation of methylene blue (MB) as well as pesticide fipronil. Best results were obtained by 5:1 MSC (98.7% degradation efficacy; rate constant 0.0261 min^-1) in 80 min under the sunlight. The effects of solution pH, catalyst-dose, scavengers and illumination-area were also explored. The catalyst was reusable as confirmed by degradation studies (~82% efficiency) even after 5-cycles. The photocatalytic treatment of real industrial-wastewater was also conducted. The TOC and COD analysis validated that the treatment by as-prepared catalyst is more proficient for effluent-treatment than the industrial physico-chemical treatments. Electrochemical degradation of MB was also investigated using the glassy carbon electrode modified with different MSC-ratios. The electrode modified with 5:1 MSC at pH 7 manifested the maximum peak current. The plausible mechanisms for photocatalytic and electrochemical degradations were proposed, which suggested the remarkable potential the prepared nanocomposites for wastewater treatment.

Electrocatalytic detection of herbicide, amitrole at WO3·0.33H2O modified carbon paste electrode for environmental applications

Environmental pollution by the heavy usage of pesticides has been a pandemic issue in view of the rising farming operations for increasing the crop yield to meet the requirements of food chain supply. Throughout the world, environmental pollution by the presence of pesticides, particularly the use of herbicides in large quantities to protect the crops, has posed many environmental issues. In this research, an electrochemical sensor based on tungsten oxide hydrates (WO₃·0.33H₂O) nanorod modified carbon paste electrode (CPE) was developed for the detection of herbicide, amitrole (AMT) by the cyclic voltammeter. Hydrothermally synthesized and characterized WO₃·0.33H₂O nanorod was found to be sensitive towards the detection of AMT due to its superior sensing property as the sensor showed enhanced current and catalytic property when used in phosphate buffer solution (PBS) of pH 5.0 by the cyclic voltammetric (CV) and square wave voltammetric (SWV) techniques. The influence of electro kinetic parameters viz., scan rate, pH, accumulation time and temperature with respect to AMT oxidation was studied using CV. The linearity range was in between 1.0 × 10^-8 M and 24 × 10^-5 M and limit of detection (LOD) and limit of quantification (LOQ) was calculated to be 2.33 nM and 7.8 nM respectively. The proposed simple method demonstrated the potential applicability to detect AMT from the soil and water samples.

ZnO-based nanostructured electrodes for electrochemical sensors and biosensors in biomedical applications

Fascinating properties of ZnO nanostructures have created much interest due to their importance in health care and environmental monitoring. Current worldwide production and their wide range of applications signify ZnO to be a representative of multi-functional oxide material. Recent nanotechnological developments have stimulated the production of various forms of ZnO nanostructures such as nano-layers, nanoparticles, nanowires, etc. Due to their enhanced sensing properties, improved binding ability with biomolecules as well as biological activities have enabled them as suitable candidates for the fabrication of biosensor devices in the biomedical arena. In this review, the synthesis of ZnO nanostructures, mechanism of their interaction with biomolecules and their applications as sensors in health care area are discussed considering the biosensors for molecules with small molecular weight, infectious diseases, and pharmaceutical compounds.

Sensitive and Selective Detection of Tartrazine Based on TiO₂-Electrochemically Reduced Graphene Oxide Composite-Modified Electrodes

TiO₂-reduced graphene oxide composite-modified glassy carbon electrodes (TiO₂–ErGO–GCE) for the sensitive detection of tartrazine were prepared by drop casting followed by electrochemical reduction. The as-prepared material was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). Cyclic voltammetry and second-order derivative linear scan voltammetry were performed to analyze the electrochemical sensing of tartrazine on different electrodes. The determination conditions (including pH, accumulation potential, and accumulation time) were optimized systematically. The results showed that the TiO₂–ErGO composites increased the electrochemical active area of the electrode and enhanced the electrochemical responses to tartrazine significantly. Under the optimum detection conditions, the peak current was found to be linear for tartrazine concentrations in the range of 2.0 × 10⁻⁸–2.0 × 10⁻⁵ mol/L, with a lower detection limit of 8.0 × 10⁻⁹ mol/L (S/N = 3). Finally, the proposed TiO₂–ErGO–GCEs were successfully applied for the detection of trace tartrazine in carbonated beverage samples.