Paste electrode based on the thermally reduced graphene oxide in ambient air – Its characterization and analytical application for analysis of 4–chloro–3,5–dimethylphenol

Improved procedure for square-wave voltammetric sensing of fenhexamid residues on blueberries peel surface at the anodically pretreated boron-doped diamond electrode

BACKGROUND

Fungicide fenhexamid (FH) has a high residual concentration on fruits and vegetables, thus, it is of high importance to monitor the level of FH residues on foodstuff samples. So far, the assay of FH residues in selected foodstuff samples has been conducted by electroanalytical methods on sp² carbon-based electrodes that are well-known to be susceptible to severe fouling of the electrodes surfaces during electrochemical measurements. As an alternative, sp³ carbon-based electrode such as boron-doped diamond (BDD) can be used in the analysis of FH residues retained on the peel surface of foodstuff (blueberries) sample.

RESULTS

In situ anodic pretreatment of the BDDE surface was found to be the most successful strategy to remediate the passivated BDDE surface by FH oxidation (by)products, and the best validation parameters, i.e., the widest linear range (3.0-100.0 μmol L^-1), the highest sensitivity (0.0265 μA L μmol^-1) and the lowest limit of detection (0.821 μmol L^-1), were achieved on the anodically pretreated BDDE (APT-BDDE) in a Britton-Robinson buffer, pH 2.0, using square-wave voltammetry (SWV). The assay of FH residues retained on blueberries peel surface was performed on the APT-BDDE using SWV, and the obtained concentration of FH residues of 6.152 μmol L^-1 (1.859 mg kg^-1) was found to be below the maximum residue value fixed for blueberries by the European Union regulations (20 mg kg^-1).

SIGNIFICANCE AND NOVELTY

In this work, a protocol based on a very easy and fast foodstuff sample preparation procedure combined with the straightforward pretreatment approach of the BDDE surface was elaborated for the first time for the monitoring of the level of FH residues retained on the peel surface of blueberries samples. The presented reliable, cost-effective, and easy-to-use protocol could find its application as a rapid screening method for the control of food safety.

Highly Sensitive Amperometric Detection of Hydrogen Peroxide in Saliva Based on N-Doped Graphene Nanoribbons and MnO2 Modified Carbon Paste Electrodes

Four different graphene-based nanomaterials (htGO, N-htGO, htGONR, and N-htGONR) were synthesized, characterized, and used as a modifier of carbon paste electrode (CPE) in order to produce a reliable, precise, and highly sensitive non-enzymatic amperometric hydrogen peroxide sensor for complex matrices. CPE, with their robustness, reliability, and ease of modification, present a convenient starting point for the development of new sensors. Modification of CPE was optimized by systematically changing the type and concentration of materials in the modifier and studying the prepared electrode surface by cyclic voltammetry. N-htGONR in combination with manganese dioxide (1:1 ratio) proved to be the most appropriate material for detection of hydrogen peroxide in pharmaceutical and saliva matrices. The developed sensor exhibited a wide linear range (1.0–300 µM) and an excellent limit of detection (0.08 µM) and reproducibility, as well as high sensitivity and stability. The sensor was successfully applied to real sample analysis, where the recovery values for a commercially obtained pharmaceutical product were between 94.3% and 98.0%. Saliva samples of a user of the pharmaceutical product were also successfully analyzed.

Interference-free electrocatalysis of p-chloro meta xylenol (PCMX) on uniquely designed optimized polymeric nanohybrid of P(EDOT-co-OPD) and fMWCNT modified glassy carbon electrode

p-Chloro-meta-Xylenol (PCMX) is an environmentally hazardous phenolic compound having biocidal and antiseptic activity. Very few research publications addressed monitoring this contaminant. This paper presents a rapid sensing system to quantify it in waste water samples. The electrochemical activity of PCMX was exploited through a unique polymeric nanocomposite modified transducer for its quantification. Poly[(3,4-Ethylenedioxythiophene)-co-(o-phenylenediamine)] [P(EDOT-co-OPD)] was deposited through one-step electropolymerization technique on the glassy carbon electrode (GCE) modified by functionalized multi-wall carbon nanotubes (fMWCNTs). An optimized combination of these constituents was evaluated using response surface methodology (RSM) based Box-Behnken experimental design. This maximized the response for PCMX using differential pulse voltammetry (DPV). The sensing matrix was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The structural and morphological study of the modified film was conducted by Fourier transform-infrared spectroscopy (FT-IR), Raman spectroscopy, scanning electron microscopy (SEM), and field emission scanning electron microscope (FESEM). The anodic peak current could be read from a wide range of 0.5-225 μM calibration curve with a detection limit of 0.2545 μmol L^-1. Interestingly this work did not use any biomaterial in the modification but achieved interference-free response with excellent selectivity, sensitivity (0.4668 μA μM^-1 cm^-2), reproducibility (RSD = 2.2%), and repeatability. The sensing platform showed good stability (85.7%) of 3 months even after 150 times repetitive use. Its applicability for real samples was established by good correlation with standard methods.

Degradation and mechanism analysis of chloroxylenol in aqueous solution by gas-liquid discharge plasma combined with ozonation

Gas-liquid discharge non-thermal plasma (NTP) coupled with an ozonation reactor was used to investigate the removal of a broad-spectrum antibacterial agent, chloroxylenol (PCMX), from aqueous solution. Under the same experimental conditions (discharge power of 50.25 W, the initial concentration of PCMX of 60 mg L-1, oxygen flow of 1.0 L min-1 and PCMX solution flow of 150 mL min-1), the PCMX degradation rates in the ozonation-only, NTP-only and NTP/O3 systems were 29.25%, 67.04% and 79.43%, respectively. Correspondingly, the energy efficiency has also been greatly improved, and increased to 0.45, 1.03 and 1.21 g kW-1 h-1. In addition, the effects of the initial concentration of PCMX, initial pH, the flow rate of oxygen, the addition of H2O2 and the addition of a radical scavenger on the degradation rate of PCMX were investigated in the NTP/O3 system. The degradation rate in acidic solutions was higher than that in alkaline solutions. During the removal process of PCMX, the rate of degradation was strongly increased with the addition of H2O2 and acutely decreased with the addition of the radical scavenger. Compared with deionized water the degradation rates of PCMX in secondary effluent were inhibited. Four main intermediates of PCMX degradation by the NTP/O3 system were identified by gas chromatography-mass spectrometry (GC-MS) and a possible degradation pathway of PCMX was proposed. The changes in toxicity of the PCMX solution during the NTP/O3 system oxidation process were also evaluated using bioluminescent bacteria and Quantitative Structure Activity Relationship (QSAR) models with the help of the ECOSAR software.