Pinecone-derived porous activated carbon for high performance all-solid-state electrical double layer capacitors fabricated with flexible gel polymer electrolytes

High-performance, high energy density symmetric supercapacitors based on δ-MnO2 nanoflower electrodes incorporated with an ion-conducting polymer

The present work investigates liquid-based and liquid-free supercapacitors assembled using δ-MnO2-nanoflower-based electrodes. An optimized electrode composition was prepared using acetylene black (AB), a polymer (PEO), a salt (LiClO4), and δ-MnO2 and used for device fabrication. The composite electrode was tested against a liquid electrolyte and a 'liquid-free' composite solid polymer electrolyte (CSPE) membrane. In a three electrode geometry, with 1 M solution of LiClO4 as an electrolyte, the specific capacitance of the electrode was found to be ∼385 F g-1, with a specific energy of ∼23 W h kg-1 and specific power of ∼341 W kg-1 (at 1 mA, 1 V). Dunn's method confirmed that the charge storage process was predominantly pseudocapacitive. When the device was assembled in a two-electrode Swagelok cell, a stable specific capacitance of ∼216 F g-1 was observed with a specific energy of 30 W h kg-1 and a specific power of 417 W kg-1. The supercapacitors exhibited stable performance up to ∼7000 cycles with ∼90% capacitance retention and ∼97% coulombic efficiency. A combination of these cells could light two white light-emitting diodes (LEDs, 3 V) for at least ∼10 minutes. Further, all-solid-state supercapacitors (ASSCs) were fabricated using a Li+ ion (CSPE) membrane. The ASSCs exhibited a specific capacitance of ∼496 F g-1 after ∼500 cycles, with a specific energy and power of ∼19 W h kg-1 and ∼367 W kg-1, respectively. The investigation reveals that the electrodes are versatile and show compatibility with liquid and solid electrolytes. The polymer in the electrode matrix plays an important role in enhancing device performance.

Pinecone derived hierarchical carbon nanostructure as a transducer in a solid-state ion-selective electrode for in vivo analysis of calcium ion

Monitoring extracellular calcium ion (Ca2+) chemical signals in neurons is crucial for tracking physiological and pathological changes associated with brain diseases in live animals. Potentiometry based solid-state ion-selective electrodes (ISEs) with the assist of functional carbon nanomaterials as ideal solid-contact layer could realize the potential response for in vitro and in vivo analysis. Herein, we employ a kind of biomass derived porous carbon as a transducing layer to prompt efficient ion to electron transduction while stabilizes the potential drift. The eco-friendly porous carbon after activation (APB) displays a high specific area with inherit macropores, micropores, and large specific capacitance. When employed as transducer in ISEs, a stable potential response, minimized potential drift can be obtained. Benefiting from these excellent properties, a solid-state Ca2+ selective carbon fiber electrodes (CFEs) with a sandwich structure is constructed and employed for real time sensing of Ca2+ under electrical stimulation. This study presents a new approach to develop sustainable and versatile transducers in solid-state ISEs, a crucial way for in vivo sensing.

Sustainable removal of caffeine and acetaminophen from water using biomass waste-derived activated carbon: Synthesis, characterization, and modelling

The removal of caffeine (CFN) and acetaminophen (ACT) from water using low-cost activated carbons prepared from artichoke leaves (AAC) and pomegranate peels (PAC) was reported in this paper. These activated carbons were characterized using various analytical techniques. The results showed that AAC and PAC had surface areas of 1203 and 1095 m2 g-1, respectively. The prepared adsorbents were tested for the adsorption of these pharmaceuticals in single and binary solutions. These experiments were performed under different operating conditions to evaluate the adsorption properties of these adsorbents to remove CFN and ACT. AAC and PAC showed maximum adsorption capacities of 290.86 and 258.98 mg g-1 for CFN removal, 281.18 and 154.99 mg g-1 for the ACT removal over a wide pH range. The experimental equilibrium adsorption data fitted to the Langmuir model and the kinetic data were correlated with the pseudo-second order model. AAC showed the best adsorption capacities for the removal of these pharmaceuticals in single systems and, consequently, it was tested for the simultaneous removal of these pollutants in binary solutions. The simultaneous adsorption of these compounds on AAC was improved using the central composite design and response surface methodology. The results indicated an antagonistic effect of CFN on the ACT adsorption. AAC regeneration was also analyzed and discussed. A statistical physics model was applied to describe the adsorption orientation of the tested pollutants on both activated carbon samples. It was concluded that AAC is a promising adsorbent for the removal of emerging pollutants due to its low cost and reusability properties.

A La2O3/MXene composite electrode for supercapacitors with improved capacitance and cycling performance

Developing efficient electrode materials is a key towards high power electrochemical energy storage devices. Two-dimensional (2D) MXene shows excellent conductivity and electrochemical performance among other materials. However, the restacking of MXene layers may degrade their specific capacity and cycling performance. Considering this challenge, here we have designed a composite made of 2D MXene nanosheets and lanthanum oxide (La2O3) nanoparticles to overcome the limitations. The bifunctionality of La2O3 nanoparticles prevents the restacking of MXene layers and enhances the electrochemical properties of the electrode due to its good Faradic characteristics. The specific capacitance of the La2O3/MXene composite electrode is 366 F/g at 1 A/g, which is 4.5 and 3 times higher than those of the individual La2O3 and MXene. The composite electrode displays a capacitance retention of 96% after 1,000 cycles, which is due to synergistic effects between the two components and indicates the potential of La2O3/MXene composite for supercapacitors.

Activated carbons with extremely high surface area produced from cones, bark and wood using the same procedure

Activated carbons have been previously produced from a huge variety of biomaterials often reporting advantages of using certain precursors. Here we used pine cones, spruce cones, larch cones and a pine bark/wood chip mixture to produce activated carbons in order to verify the influence of the precursor on properties of the final materials. The biochars were converted into activated carbons with extremely high BET surface area up to ∼3500 m² g^-1 (among the highest reported) using identical carbonization and KOH activation procedures. The activated carbons produced from all precursors demonstrated similar specific surface area (SSA), pore size distribution and performance to electrodes in supercapacitors. Activated carbons produced from wood waste appeared to be also very similar to "activated graphene" prepared by the same KOH procedure. Hydrogen sorption of AC follows expected uptake vs. SSA trends and energy storage parameters of supercapacitor electrodes prepared from AC are very similar for all tested precursors. It can be concluded that the type of precursor (biomaterial or reduced graphene oxide) has smaller importance for producing high surface area activated carbons compared to details of carbonization and activation. Nearly all kinds of wood waste provided by the forest industry can possibly be converted into high quality AC suitable for preparation of electrode materials.

High-surface-area activated carbon from pine cones for semi-industrial spray deposition of supercapacitor electrodes

High surface area carbons are so far the best materials for industrial manufacturing of supercapacitor electrodes. Here we demonstrate that pine cones, an abundant bio-precursor currently considered as a waste in the wood industry, can be used to prepare activated carbons with a BET surface area exceeding 3000 m² g^-1. It is found that the same KOH activation procedure applied to reduced graphene oxide (rGO) and pine cone derived biochars results in carbon materials with a similar surface area, pore size distribution and performance in supercapacitor (SC) electrodes. It can be argued that "activated graphene" and activated carbon are essentially the same kind of material with a porous 3D structure. It is demonstrated that the pine cone derived activated carbon (PC-AC) can be used as a main part of aqueous dispersions stabilized by graphene oxide for spray deposition of electrodes. The PC-AC based electrodes prepared using a semi-industrial spray gun machine and laboratory scale blade deposition of these dispersions were compared to pellet electrodes.

Coherent Integration of Organic Gel Polymer Electrolyte and Ambipolar Polyoxometalate Hybrid Nanocomposite Electrode in a Compact High-Performance Supercapacitor

We report a gel polymer electrolyte (GPE) supercapacitor concept with improved pathways for ion transport, thanks to a facile creation of a coherent continuous distribution of the electrolyte throughout the electrode. Poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) was chosen as the polymer framework for organic electrolytes. A permeating distribution of the GPE into the electrodes, acting both as integrated electrolyte and binder, as well as thin separator, promotes ion diffusion and increases the active electrode–electrolyte interface, which leads to improvements both in capacitance and rate capability. An activation process induced during the first charge–discharge cycles was detected, after which, the charge transfer resistance and Warburg impedance decrease. We found that a GPE thickness of 12 μm led to optimal capacitance and rate capability. A novel hybrid nanocomposite material, formed by the tetraethylammonium salt of the 1 nm-sized phosphomolybdate cluster and activated carbon (AC/TEAPMo12), was shown to improve its capacitive performance with this gel electrolyte arrangement. Due to the homogeneous dispersion of PMo12 clusters, its energy storage process is non-diffusion-controlled. In the symmetric capacitors, the hybrid nanocomposite material can perform redox reactions in both the positive and the negative electrodes in an ambipolar mode. The volumetric capacitance of a symmetric supercapacitor made with the hybrid electrodes increased by 40% compared to a cell with parent AC electrodes. Due to the synergy between permeating GPE and the hybrid electrodes, the GPE hybrid symmetric capacitor delivers three times more energy density at higher power densities and equivalent cycle stability compared with conventional AC symmetric capacitors.

Synthesis and Encapsulation of Ajuga parviflora Extract with Zeolitic Imidazolate Framework-8 and Their Therapeutic Action against G+ and G- Drug-Resistant Bacteria

Infectious diseases caused by bacteria have become a public health issue. Antibiotic therapy for infectious disorders, as well as antibiotic overuse, has resulted in antibiotic-resistant bacterial strains. Zeolitic imidazolate framework-8 (ZIF-8) possesses a wide surface area, high porosity, variable functionality, and potential drug carriers. We have established a clear method for making a nanoscale APE@ZIF-8 nanocomposite agent with outstanding antibacterial activity against methicillin-resistant Staphylococcus aureus (MRSA) and cephalosporin-carbapenem-resistant Escherichia coli (CCREC). We present a unique approach for encapsulating molecules ofAjuga parviflora extract (APE) with ZIF-8. APE@ZIF-8 has a positive charge. By electrostatic contact with the negatively charged bacterial surface of S. aureus and E. coli, APE@ZIF-8 NPs produce reactive oxygen species (ROS) that damage bacterial cell organelles. As a result, the APE@ZIF-8 nanocomposite offers limitless application potential in the treatment of infectious disorders caused by drug-resistant gram-positive and gram-negative bacteria.

Enhanced electrochemical performance of MnNi2O4/rGO nanocomposite as pseudocapacitor electrode material and methanol electro-oxidation catalyst

Binary transition metal oxides with encouraging electrocatalyst properties have been suggested as electrode materials for supercapacitors and methanol oxidation. Hence, in this work, a binary mixed metal oxide based on nickel and manganese (MnNi₂O₄) and its hybrid with reduced graphene oxide were synthesized by a one-step hydrothermal method. After physical and morphological characterization, the potential of these nanostructures was investigated for use as supercapacitor electrodes and methanol electro-oxidation. The results of the electrochemical analysis showed a substantial effect of adding rGO to the MnNi₂O₄. The MnNi₂O₄/rGO hybrid electrode supercapacitor exhibited good stability of 93% after 2000 consecutive CV cycles and a specific capacitance of 575 F g^-1at the current density of 0.5 A g^-1. Furthermore, the application of this hybrid nanomaterial in the methanol electro-oxidation reaction (MOR) indicated its appropriate electrochemical efficiency and stability in methanol oxidation. Our results show that MnNi₂O₄/rGO can be considered as a promising electrode material for energy applications.

Coconut-shell-derived activated carbon for NIR photo-activated synergistic photothermal-chemodynamic cancer therapy

Exploiting new non-metal-based peroxidase-mimic nanoenzymes for chemodynamic therapy (CDT) in cancer treatment is an active and challenging field. Here, we found that activated carbon nanoparticles (denoted as ANs) fabricated from coconut shell have satisfactory peroxidase-mimic nanoenzyme activity. Based on this positive result, gadodiamide, a clinically used nuclear magnetic imaging contrast agent, was loaded inside the AN pores and encapsulated by polyvinylpyrrolidone (PVP) to obtain Gd@PANs. PANs (ANs modified using PVP) efficiently catalyze the massive decomposition of endogenous hydrogen peroxide (H2O2) inside cancer cells to produce toxic oxidized hydroxyl radicals (˙OH) for the CDT treatment of cancer, but they showed no toxicity toward normal cells. Additionally, under 808 nm laser irradiation, the photothermal conversion efficiency of the PANs reaches 45.20%, ensuring their effective photothermal therapy (PTT) treatment functionality. Simultaneously, during PTT treatment, the heating effect significantly enhances the peroxidase-mimic activity of the PANs to achieve an ideal PTT-CDT synergistic therapeutic outcome. Gd@PANs can also be used for the T1-magnetic resonance imaging (MRI) of tumors to integrate treatment and diagnosis.

"Water-in-salt" electrolyte enhanced high voltage aqueous supercapacitor with carbon electrodes derived from biomass waste-ground grain hulls

To design high specific surface area and optimize the pore size distribution of materials, we employ a combination of carbonization and KOH activation to prepare activated carbon derived from ground grain hulls. The resulting carbon material at lower temperature (800, BSAC-A-800) exhibits a porous structure with a high specific surface area of 1037.6 m2 g-1 and a pore volume of 0.57 m3 g-1. Due to the synergistic structural characteristics, BSAC-A-800 reveals preferable capacitive performance, showing a specific capacitance as high as 313.3 F g-1 at 0.5 A g-1, good rate performance (above 73%), and particularly stable cycling performance (99.1% capacitance retention after 10 000 cycles at a current density of 10 A g-1). More importantly, the assembled symmetric supercapacitor using a water-in-salt electrolyte (17 m NaClO4) with high discharge specific capacitance (59 F g-1 at 0.5 A g-1), high energy density (47.2 W h kg-1) and high voltage (2.4 V) represents significant progress towards performance comparable to that of commercial salt-in-water electrolyte supercapacitors (with discharge specific capacitance of 50 F g-1, energy densities of ∼28.1 W h kg-1 and voltages of 2.0 V).

Hierarchically Nanoporous Pyropolymers Derived from Waste Pinecone as a Pseudocapacitive Electrode for Lithium Ion Hybrid Capacitors

The non-aqueous asymmetric lithium ion hybrid capacitor (LIHC) is a tactical energy storage device composed of a faradic and non-faradic electrode pair, which aims to achieve both high energy and great power densities. On the other hand, the different types of electrode combinations cause severe imbalances in energy and power capabilities, leading to poor electrochemical performance. Herein, waste pinecone-derived hierarchically porous pyropolymers (WP-HPPs) were fabricated as a surface-driven pseudocapacitive electrode, which has the advantages of both faradic and non-faradic electrodes. The unique materials properties of WP-HPPs possessing high effective surface areas and hierarchically open nanopores led to high specific capacities of ~412 mA h g⁻¹ and considerable rate/cycling performance as a cathode for LIHCs. In particular, nanometer-scale pores, approximately 3 nm in size, plays a key role in the pseudocapacitive charge storage behaviors because open nanopores can transport solvated Li-ions easily into the inside of complex carbon structures and a large specific surface area can be provided by the effective active surface for charge storage. In addition, WP-HPP-based asymmetric LIHCs assembled with a pseudocapacitive counterpart demonstrated feasible electrochemical performance, such as maximum specific energy and specific power of ~340 Wh kg⁻¹ and ~11,000 W kg⁻¹, respectively, with significant cycling stability.

Three-dimensional high performance free-standing anode by one-step carbonization of pinecone in microbial fuel cells

In this paper, the free-standing macroporous carbon anode is prepared by one-step carbonization of pinecone without any further modification. The obtained anode is N, P-codoped porous carbon material, which is beneficial for electrochemical active bacterial adhesion and the fast start-up of cells. Both of the output voltage and long-term operation stability of the obtained anode are higher than that of carbon felt. The charge transfer resistance after biofilm formation is only 1.4 Ω, being 85.1% lower than that of carbon felt anode. 16S rRNA gene sequence analysis shows that Geobacter soli is the main electricigen and its ratio at the obtained anode is much higher than that at carbon felt (77.4% vs 34.0%). The N, P-codoped carbon as the three-dimensional free-standing anode has excellent electrochemical properties and is low cost and easy preparation. Most importantly, it enhances extracellular electron transfer, thus has potential application in microbial fuel cells.