Constructing a high-performance quasi-solid-state asymmetric supercapacitor: NaxMnO2@CNT/WPU-PAAK-Na2SO4/AC-CNT

In Situ Converting Conformal Sacrificial Layer Into Robust Interphase Stabilizes Fluorinated Polyanionic Cathodes for Aqueous Sodium-Ion Storage

Sodium vanadium oxy-fluorophosphates (NVOPF), as typical fluorinated polyanionic compounds, are considered high-voltage and high-capacity cathode materials for aqueous sodium-ion storage. However, the poor cycle life caused by interfacial degradation (especially the attack of specific HF by-products) greatly hampers their application in aqueous electrolytes. Here, it is shown that in situ converting harmful HF derivate to F-containing cathode electrolyte interphase (CEI) can overcome the above challenge. As a proof-of-concept, a conformal Al2O3 sacrificial layer is precoated on NVOPF for on-site generating robust AlF3-rich CEI while eliminating continuous HF release. The evolved CEI chemistry mitigates interfacial side reactions, inhibits vanadium dissolution, and promotes Na+ transport kinetics, thus significantly boosting cycling stability (capacity retention rate increased to 3.15 times), rate capability, and even low-temperature performance (≈1.5 times capacity improvement at -20 °C). When integrated with pseudocapacitive zeolite-templated carbon anode and adhesive hydrogel electrolyte, a unique 2.3 V quasi-solid-state sodium-ion hybrid capacitor is developed, exhibiting remarkable cycle life (77.0% after 1000 cycles), high energy and power densities, and exceptional safety against extreme conditions. Furthermore, a photovoltaic energy storage module is demonstrated, highlighting the potential use in future smart/microgrids. The work paves new avenues for enabling the use of unstable electrode materials via interfacial engineering.

Polymer Electrolytes for Supercapacitors

Because of safety concerns associated with the use of liquid electrolytes and electrolyte solutions, options for non-liquid materials like gels and polymers to be used as ion-conducting electrolytes have been explored intensely, and they attract steadily growing interest from researchers. The low ionic conductivity of most hard and soft solid materials was initially too low for practical applications in supercapacitors, which require low internal resistance of a device and, consequently, highly conducting materials. Even if an additional separator may not be needed when the solid electrolyte already ensures reliable separation of the electrodes, the electrolytes prepared as films or membranes as thin as practically acceptable, resistance may still be too high even today. Recent developments with gel electrolytes sometimes approach or even surpass liquid electrolyte solutions, in terms of effective conductance. This includes materials based on biopolymers, renewable raw materials, materials with biodegradability, and better environmental compatibility. In addition, numerous approaches to improving the electrolyte/electrode interaction have yielded improvements in effective internal device resistance. Reported studies are reviewed, material combinations are sorted out, and trends are identified.

Comprehensive Study on the Ion-Selective Behavior of MnOx for Electrochemical Deionization

Manganese oxide is an effective active material in several electrochemical systems, including batteries, supercapacitors, and electrochemical deionization (ECDI). This work conducts a comprehensive study on the ion-selective behavior of MnOx to fulfill the emptiness in the energy and environmental science field. Furthermore, it broadens the promising application of MnOx in the ion-selective ECDI system. We propose a time-dependent multimechanism ion-selective behavior with the following guidelines by utilizing a microfluidic cell and the electrochemical quartz crystal microbalance (EQCM) analysis. (1) Hydrated radius is the most critical factor for ions with the same valence, and MnOx tends to capture cations with a small hydrated radius. (2) The importance of charge density rises when comparing cations with different valences, and MnOx prefers to capture divalent cations with a strong electrostatic attraction at prolonged times. Under this circumstance, ion swapping may occur where divalent cations replace monovalent cations. (3) NH4+ triggers MnOx dissolution, leading to performance and stability decay. The EQCM evidence has directly verified the proposed mechanisms, and these data provide a novel but simple method to judge ion selectivity preference. The overall ion selectivity sequence is Ca2+ > Mg2+ > K+ > NH4+> Na+ > Li+ with the highest selectivity values of βCa//Li and βCa//Na around 3 at the deionization time = 10 min.

Preparation of NiO decorated CNT/ZnO core-shell hybrid nanocomposites with the aid of ultrasonication for enhancing the performance of hybrid supercapacitors

Supercapacitor (SC) electrodes fabricated with the combination of carbon nanotubes (CNTs) and metal oxides are showing remarkable advancements in the electrochemical properties. Herein, NiO decorated CNT/ZnO core-shell hybrid nanocomposites (CNT/ZnO/NiO HNCs) are facilely synthesized by a two-step solution-based technique for the utilization in hybrid supercapacitors. Benefitting from the synergistic advantages of three materials, the CNT/ZnO/NiO HNCs based electrode has evinced superior areal capacity of ~67 µAh cm-2 at a current density of 3 mA cm-2 with an exceptional cycling stability of 112% even after 3000 cycles of continuous operation. Highly conductive CNTs and electrochemically active ZnO contribute to the performance enhancement. Moreover, the decoration of NiO on the surface of CNT/ZnO core-shell increases the electro active sites and stimulates the faster redox reactions which play a vital role in augmenting the electrochemical properties. Making the use of high areal capacity and ultra-long stability, a hybrid supercapacitor (HSC) was assembled with CNT/ZnO/NiO HNCs coated nickel foam (CNT/ZnO/NiO HNCs/NF) as positive electrode and CNTs coated NF as negative electrode. The fabricated HSC delivered an areal capacitance of 287 mF cm-2 with high areal energy density (67 µWh cm-2) and power density (16.25 mW cm-2). The combination of battery type CNT/ZnO/NiO HNCs/NF and EDLC type CNT/NF helped in holding the capacity for a long period of time. Thus, the systematic assembly of CNTs and ZnO along with the NiO decoration enlarges the application window with its high rate electrochemical properties.

Advanced materials and technologies for supercapacitors used in energy conversion and storage: a review

Supercapacitors are increasingly used for energy conversion and storage systems in sustainable nanotechnologies. Graphite is a conventional electrode utilized in Li-ion-based batteries, yet its specific capacitance of 372 mA h g−1 is not adequate for supercapacitor applications. Interest in supercapacitors is due to their high-energy capacity, storage for a shorter period and longer lifetime. This review compares the following materials used to fabricate supercapacitors: spinel ferrites, e.g., MFe2O4, MMoO4 and MCo2O4 where M denotes a transition metal ion; perovskite oxides; transition metals sulfides; carbon materials; and conducting polymers. The application window of perovskite can be controlled by cations in sublattice sites. Cations increase the specific capacitance because cations possess large orbital valence electrons which grow the oxygen vacancies. Electrodes made of transition metal sulfides, e.g., ZnCo2S4, display a high specific capacitance of 1269 F g−1, which is four times higher than those of transition metals oxides, e.g., Zn–Co ferrite, of 296 F g−1. This is explained by the low charge-transfer resistance and the high ion diffusion rate of transition metals sulfides. Composites made of magnetic oxides or transition metal sulfides with conducting polymers or carbon materials have the highest capacitance activity and cyclic stability. This is attributed to oxygen and sulfur active sites which foster electrolyte penetration during cycling, and, in turn, create new active sites.