Free-standing N-Graphene as conductive matrix for Ni(OH)2 based supercapacitive electrodes

Strategy of Voltage Match on the Maximum Power Point for a High-Efficiency Photorechargeable Device

A photorechargeable device can generate power from sunlight and store it in one device, which has a broad application prospect in the future. However, if the working state of the photovoltaic part in the photorechargeable device deviates from the maximum power point, its actual power conversion efficiency will reduce. The strategy of voltage match on the maximum power point is reported to achieve a high overall efficiency (η_oa) of the photorechargeable device assembled by a passivated emitter and rear cell (PERC) solar cell and Ni-based asymmetric capacitors. According to matching the voltage of the maximum power point of the photovoltaic part, the charging characteristics of the energy storage part are adjusted to realize a high actual power conversion efficiency of the photovoltaic part (η_pv). The η_pv of a Ni(OH)₂-rGO-based photorechargeable device is 21.53%, and the η_oa is up to 14.55%. This strategy can promote further practical application for the development of photorechargeable devices.

Battery-Type-Behavior-Retention Ni(OH)2-rGO Composite for an Ultrahigh-Specific-Capacity Asymmetric Electrochemical Capacitor Electrode

Nanosized battery-type materials applied in electrochemical capacitors can effectively reduce a series of problems caused by low conductivity and large volume changes. However, this approach will lead to the charging and discharging process being dominated by capacitive behavior, resulting in a serious decline in the specific capacity of the material. By controlling the material particles to an appropriate size and a suitable number of nanosheet layers, the battery-type behavior can be retained to maintain a large capacity. Here, Ni(OH)₂, which is a typical battery-type material, is grown on the surface of reduced graphene oxide to prepare a composite electrode. By controlling the dosage of the nickel source, the composite material with an appropriate Ni(OH)₂ nanosheet size and a suitable number of layers was prepared. The high-capacity electrode material was obtained by retaining the battery-type behavior. The prepared electrode had a specific capacity of 397.22 mA h g^-1 at 2 A g^-1. After the current density was increased to 20 A g^-1, the retention rate was as high as 84%. The prepared asymmetric electrochemical capacitor had an energy density of 30.91 W h kg^-1 at a power density of 1319.86 W kg^-1 and the retention rate could reach 79% after 20,000 cycles. We advocate an optimization strategy that retains the battery-type behavior of electrode materials by increasing the size of nanosheets and the number of layers, which can significantly improve the energy density while combining the advantage of the high rate capability of the electrochemical capacitor.

Steps towards highly-efficient water splitting and oxygen reduction using nanostructured β-Ni(OH)2

β-Ni(OH)2 nanoplatelets are prepared by a hydrothermal procedure and characterized by scanning and transmission electron microscopy, X-ray diffraction analysis, Raman spectroscopy, and X-ray photoelectron spectroscopy. The material is demonstrated to be an efficient electrocatalyst for oxygen reduction, oxygen evolution, and hydrogen evolution reactions in alkaline media. β-Ni(OH)2 shows an overpotential of 498 mV to reach 10 mA cm-2 towards oxygen evolution, with a Tafel slope of 149 mV dec-1 (decreasing to 99 mV dec-1 at 75 °C), along with superior stability as evidenced by chronoamperometric measurements. Similarly, a low overpotential of -333 mV to reach 10 mA cm-2 (decreasing to only -65 mV at 75 °C) toward hydrogen evolution with a Tafel slope of -230 mV dec-1 is observed. Finally, β-Ni(OH)2 exhibits a noteworthy performance for the ORR, as evidenced by a low Tafel slope of -78 mV dec-1 and a number of exchanged electrons of 4.01 (indicating direct 4e--oxygen reduction), whereas there are only a few previous reports on modest ORR activity of pure Ni(OH)2.

Carbon–nitrogen–metal material as a high performing oxygen evolution catalyst

Oxygen evolution reaction catalysts composed of Ni–N3 molecular motifs grafted onto carbon black.

Standing and Lying Ni(OH)2 Nanosheets on Multilayer Graphene for High-Performance Supercapacitors

For conventional synthesis of Ni(OH)₂/graphene hybrids, oxygen-containing functional groups should be firstly introduced on graphene to serve as active sites for the anchoring of Ni(OH)₂. In this work, a method for growing Ni(OH)₂ nanosheets on multilayer graphene (MLG) with molecular connection is developed which does not need any pre-activation treatments. Moreover, Ni(OH)₂ nanosheets can be controlled to stand or lie on the surface of MLG. The prepared hybrids were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The growth processes are suggested according to their morphologies at different growth stages. The enhanced electrochemical performances as supercapacitor electrode materials were confirmed by cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) techniques. Ni(OH)₂ nanosheets standing and lying on MLG show specific capacities of 204.4 mAh g⁻¹ and 131.7 mAh g⁻¹, respectively, at 1 A g⁻¹ based on the total mass of the hybrids and 81.5% and 92.8% capacity retention at a high current density of 10 A g⁻¹, respectively. Hybrid supercapacitors with as-prepared hybrids as cathodes and activated carbon as anode were fabricated and tested.

Advanced Carbon-Nickel Sulfide Hybrid Nanostructures: Extending the Limits of Battery-Type Electrodes for Redox-Based Supercapacitor Applications

Transition-metal sulfides combined with conductive carbon nanostructures are considered promising electrode materials for redox-based supercapacitors due to their high specific capacity. However, the low rate capability of these electrodes, still considered "battery-type" electrodes, presents an obstacle for general use. In this work, we demonstrate a successful and fast fabrication process of metal sulfide-carbon nanostructures ideal for charge-storage electrodes with ultra-high capacity and outstanding rate capability. The novel hybrid binder-free electrode material consists of a vertically aligned carbon nanotube (VCN), terminated by a nanosized single-crystal metallic Ni grain; Ni is covered by a nickel nitride (Ni₃N) interlayer and topped by trinickel disulfide (Ni₃S₂, heazlewoodite). Thus, the electrode is formed by a Ni₃S₂/Ni₃N/Ni@NVCN architecture with a unique broccoli-like morphology. Electrochemical measurements show that these hybrid binder-free electrodes exhibit one of the best electrochemical performances compared to the other reported Ni₃S₂-based electrodes, evidencing an ultra-high specific capacity (856.3 C g^-1 at 3 A g^-1), outstanding rate capability (77.2% retention at 13 A g^-1), and excellent cycling stability (83% retention after 4000 cycles at 13 A g^-1). The remarkable electrochemical performance of the binder-free Ni₃S₂/Ni₃N/Ni@NVCN electrodes is a significant step forward, improving rate capability and capacity for redox-based supercapacitor applications.

Direct Growth of Oxygen Vacancy-Enriched Co3O4 Nanosheets on Carbon Nanotubes for High-Performance Supercapacitors

Ultrathin Co₃O₄ nanosheets (NSs) with abundant oxygen vacancies on conductive carbon nanotube (CNT) nanocomposites (termed as Co₃O₄-NSs/CNTs) are easily achieved by an effective NaBH₄-assisted cyanogel hydrolysis strategy under ambient conditions. The specific capacitance of Co₃O₄-NSs/CNTs with 5% CNT mass can reach 1280.4 F g^-1 at 1 A g^-1 and retain 112.5% even after 10 000 cycles, demonstrating very high electrochemical capability and stability. When assembled in the two-electrode Co₃O₄-NSs/CNTs-5%//reduced graphene oxide (rGO) system, a maximum specific energy density of 37.2 Wh kg^-1 (160.2 W kg^-1) is obtained at room temperature. Ultrathin structure of nanosheets, abundant oxygen vacancies, and the synergistic effect between Co₃O₄-NSs and CNTs are crucial factors for excellent electrochemical performance. Specifically, these characteristics favor rapid electron transfer, complete exposure of the active interface, and sufficient adsorption/desorption of electrolyte ions within the active material. This work gives insights into the efficient construction of two-dimensional hybrid electrodes with high performance for the new-generation energy storage system.

Ni on graphene oxide: a highly active and stable alkaline oxygen evolution catalyst

A novel oxygen evolution catalyst was prepared by reacting NiCl₂·6H₂O with electrochemically exfoliated graphene oxide (EGO) using mild reaction conditions, leading to the simultaneous formation and deposition of Ni oxide nanoparticles onto EGO.

Promising Rice-Husk-Derived Carbon/Ni(OH)2 Composite Materials as a High-Performing Supercapacitor Electrode

Improving the electrochemical performance of biomass-derived carbon electrode-active materials for supercapacitor applications has recently attracted considerable attention. Herein, we develop hybrid electrode materials from rice-husk-derived porous carbon (RH-C) materials and β-Ni(OH)₂ via a facile solid-state reaction strategy comprising two steps. The prepared RH-C/Ni(OH)₂ (C-Ni) was investigated using scanning electron microscopy (SEM) (energy-dispersive X-ray spectrometer (EDS)), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD) to acquire the physical and chemical information, which was used to demonstrate the successful fabrication of C-Ni. Thermogravimetric analysis (TGA) measurement results confirmed that the thermal stability of C-Ni changed due to the presence of Ni(OH)₂. As expected, C-Ni possesses a high capacitance of ∼952 F/g at a current density of 1.0 A/g. This result is higher than that of pure biomass-based carbon materials under the three-electrode system. This facile preparation method, which was used to synthesize the electrode-active materials, can extend to the value-added utility of other waste biomass materials as high-performing supercapacitor electrodes for energy storage applications.

Versatility of Amide-Functionalized Co(II) and Ni(II) Coordination Polymers: From Thermochromic-Triggered Structural Transformations to Supercapacitors and Electrocatalysts for Water Splitting

The new 2D coordination polymers (CPs) [M(L)₂(H₂O)₂]_n [M = Co^II (1) and Ni^II (2); L = 4-(pyridin-3-ylcarbamoyl)benzoate] were synthesized from pyridyl amide-functionalized benzoic acid (HL). They were characterized by elemental, Fourier transform infrared, thermogravimetric, powder X-ray diffraction (PXRD), and single-crystal X-ray diffraction (XRD) structural analyses. Single-crystal XRD analysis revealed the presence of a 2D polymeric architecture, and topological analyses disclose a 2,4-connected binodal net. A thermochromic effect leads to the production of two new CPs, 1' and 2', by heating at ca. 220 °C, accompanied by a color change from orange to purple in the case of 1 and from blue to green in the case of 2. The transformation of 1 to 1' takes place through an intermediate (1a) with a different twist of the L^- ligand, leading to the formation of a 1D polymeric architecture, as proven by single-crystal XRD analysis. The addition of water or keeping 1' or 2' in air for several days leads to regeneration of 1 or 2, respectively. The thermochromic-triggered structural transformations of 1 and 2 were further substantiated by PXRD and UV-vis ground-state diffuse-reflectance absorption studies. The supercapacitance ability of the CPs 1 and 2 and a Ni-Co composite (made from mixing the CPs 1 and 2) was investigated by electroanalytical techniques, such as cyclic voltammetry and electrochemical impedance spectroscopy. The CP 2 exhibits the highest specific capacity of 273.8 C g^-1 at an applied current density of 1.5 A g^-1. These newly developed CPs further act as electrocatalysts for the water-splitting reaction.

Simultaneous Synthesis and Nitrogen Doping of Free-Standing Graphene Applying Microwave Plasma

An experimental and theoretical investigation on microwave plasma-based synthesis of free-standing N-graphene, i.e., nitrogen-doped graphene, was further extended using ethanol and nitrogen gas as precursors. The in situ assembly of N-graphene is a single-step method, based on the introduction of N-containing precursor together with carbon precursor in the reactive microwave plasma environment at atmospheric pressure conditions. A previously developed theoretical model was updated to account for the new reactor geometry and the nitrogen precursor employed. The theoretical predictions of the model are in good agreement with all experimental data and assist in deeper understanding of the complicated physical and chemical process in microwave plasma. Optical Emission Spectroscopy was used to detect the emission of plasma-generated ‘‘building units’’ and to determine the gas temperature. The outlet gas was analyzed by Fourier-Transform Infrared Spectroscopy to detect the generated gaseous by-products. The synthesized N-graphene was characterized by Scanning Electron Microscopy, Raman, and X-ray photoelectron spectroscopies.

Graphene and Lithium-Based Battery Electrodes: A Review of Recent Literature

Graphene is a new generation material, which finds potential and practical applications in a vast range of research areas. It has unrivalled characteristics, chiefly in terms of electronic conductivity, mechanical robustness and large surface area, which allow the attainment of outstanding performances in the material science field. Some unneglectable issues, such as the high cost of production at high quality and corresponding scarce availability in large amounts necessary for mass scale distribution, slow down graphene widespread utilization; however, in the last decade both basic academic and applied industrial materials research have achieved remarkable breakthroughs thanks to the implementation of graphene and related 1D derivatives. In this work, after briefly recalling the main characteristics of graphene, we present an extensive overview of the most recent advances in the development of the Li-ion battery anodes granted by the use of neat and engineered graphene and related 1D materials. Being far from totally exhaustive, due to the immense scientific production in the field yearly, we chiefly focus here on the role of graphene in materials modification for performance enhancement in both half and full lithium-based cells and give some insights on related promising perspectives.