Promoting the electrocatalytic performance of PbO2 nanocrystals via incorporation of Y2O3 nanoparticles: Degradation application and electrocatalytic mechanism

Side Reaction Turned Positive: Synchronous OER Manipulating the Electrocatalytic Properties of Anodic Electrodeposited Lead Dioxide

The preparation and modification of porous electrodes are an important component of the new generation electrochemical oxidation technology. Rapid preparation of porous electrodes can be easily achieved by synchronous oxygen bubble electrodeposition. However, according to the reaction mechanism of lead dioxide anodic electrodeposition, there is bound to be a competitive reaction of adsorbed hydroxyl radicals in the oxygen bubble template method, which means that synchronous OER impacts both the surface morphology and potentially the crystalline structure of the metal oxides. Clarifying the comprehensive influence of synchronous OER on the morphology and microstructure of the coating is important. In this work, the electrodeposition process of porous lead dioxide coating is regulated by the way of linear potential increase and realized the rapid preparation of high-performance porous lead dioxide coating within 40 s. The morphology and microstructure, electrical, and electrochemical properties are characterized, combined with theoretical calculation and orthogonal analysis, to investigate the regulatory mechanism of the rapid growth of the porous lead dioxide by the electric potential. It is demonstrated that synchronous OER confers porous morphology and a large number of defects to the coating in situ, and enhancing the electrocatalytic oxidation performance of the electrode.

Y-mediated optimization of 3DG-PbO2 anode for electrochemical degradation of PFOS

In our previous study, the three-dimensional graphene-modified PbO2 (3DG-PbO2) anode was prepared for the effective degradation of perfluorooctanesulfonat (PFOS) by the electrochemical oxidation process. However, the mineralization efficiency of PFOS at the 3DG-PbO2 anode still needs to be further improved due to the recalcitrance of PFOS. Thus, in this study, the yttrium (Y) was doped into the 3DG-PbO2 film to further improve the electrochemical activity of the PbO2 anode. To optimize the doping amount of Y, three Y and 3DG codoped PbO2 anodes were fabricated with different Y3+ concentrations of 5, 15, and 30 mM in the electroplating solution, which were named Y/3DG-PbO2-5, Y/3DG-PbO2-15 and Y/3DG-PbO2-30, respectively. The results of morphological, structural, and electrochemical characterization revealed that doping Y into the 3DG-PbO2 anode further refined the β-PbO2 crystals, increased the oxygen evolution overpotential and active sites, and reduced the electron transfer resistance, resulting in a superior electrocatalytic activity. Among all the prepared anodes, the Y/3DG-PbO2-15 anode exhibited the best activity for electrochemical oxidation of PFOS. After 120 min of electrolysis, the TOC removal efficiency was 80.89% with Y/3DG-PbO2-15 anode, greatly higher than 69.13% with 3DG-PbO2 anode. In addition, the effect of operating parameters on PFOS removal was analyzed by response surface, and the obtained optimum values of current density, initial PFOS concentration, pH, and Na2SO4 concentration were 50 mA/cm2, 12.21 mg/L, 5.39, and 0.01 M, respectively. Under the optimal conditions, the PFOS removal efficiency reached up to 97.16% after 40 min of electrolysis. The results of the present study confirmed that the Y/3DG-PbO2 was a promising anode for electrocatalytic oxidation of persistent organic pollutants.

A non-steroidal drug "diclofenac" is a substrate for electrochemical degradation process using graphite anode

In the electrochemical degradation process, the elimination of organic pollutants could be enhanced using supporting electrolyte and applied voltage. After degradation of the target organic compound, some by-products are formed. Chlorinated by-products are the main products formed in the presence of sodium chloride. In the present study, an electrochemical oxidation process has been applied to diclofenac (DCF) using graphite as an anode and sodium chloride (NaCl) as a supporting electrolyte. Monitoring the removal of the by-products and elucidating them were provided using HPLC and LC-TOF/MS, respectively. A high removal% of 94% DCF was observed under the conditions: 0.5 g NaCl, 5 V, and 80 min of electrolysis, while the removal% of chemical oxygen demand (COD) was 88% under the same conditions, but 360 min of electrolysis was required. The pseudo-first-order rate constant values were quite varied based on the selected experimental conditions; the rate constants were between 0.0062 and 0.054 min^-1, between 0.0024 and 0.0326 min^-1 under the influence of applied voltage and sodium chloride, respectively. The maximum values of energy consumption were 0.93 and 0.55 Wh/mg using 0.1 g NaCl and 7 V, respectively. Some chlorinated by-products, C₁₃H₁₈Cl₂NO₅, C₁₁H₁₀Cl₃NO₄, and C₁₃H₁₃Cl₅NO₅, were selected and elucidated using LC-TOF/MS.

Elaboration of Highly Modified Stainless Steel/Lead Dioxide Anodes for Enhanced Electrochemical Degradation of Ampicillin in Water

Lead dioxide-based electrodes have shown a great performance in the electrochemical treatment of organic wastewater. In the present study, modified PbO2 anodes supported on stainless steel (SS) with a titanium oxide interlayer such as SS/TiO2/PbO2 and SS/TiO2/PbO2-10% Boron (B) were prepared by the sol–gel spin-coating technique. The morphological and structural properties of the prepared electrodes were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS). It was found that the SS/TiO2/PbO2-10% B anode led to a rougher active surface, larger specific surface area, and therefore stronger ability to generate powerful oxidizing agents. The electrochemical impedance spectroscopy (EIS) measurements showed that the modified PbO2 anodes displayed a lower charge transfer resistance Rct. The influence of the introduction of a TiO2 intermediate layer and the boron doping of a PbO2 active surface layer on the electrochemical degradation of ampicillin (AMP) antibiotic have been investigated by chemical oxygen demand measurements and HPLC analysis. Although HPLC analysis showed that the degradation process of AMP with SS/PbO2 was slightly faster than the modified PbO2 anodes, the results revealed that SS/TiO2/PbO2-10%B was the most efficient and economical anode toward the pollutant degradation due to its physico-chemical properties. At the end of the electrolysis, the chemical oxygen demand (COD), the average current efficiency (ACE) and the energy consumption (EC) reached, respectively, 69.23%, 60.30% and 0.056 kWh (g COD)−1, making SS/TiO2/PbO2-10%B a promising anode for the degradation of ampicillin antibiotic in aqueous solutions.

Electrocatalysis degradation of coal tar wastewater using a novel hydrophobic benzalacetone modified lead dioxide electrode

Coal tar wastewater is hard to degrade by traditional methods because of its toxic pollutant constituents and high concentration of aromatic hydrocarbons, especially phenolic substances. A new type of hydrophobic benzacetone modified PbO₂ anode (BA-PbO₂ electrodes) was used for the electrocatalytic treatment of coal tar wastewater in a continuous cycle reactor. The surface morphology, structure, valences of elements, hydrophobicity, hydroxyl radical (·OH) produced capacity, electrochemical properties and stability of BA-PbO₂ electrodes were characterized by SEM (scanning electron microscopy), XRD (X-ray diffraction), XPS (X-ray photoelectron spectroscopy), contact angle, a fluorescence probe test, an electrochemical workstation and accelerated life test, respectively. The BA-PbO₂ electrodes exhibited a compact structure and finely dispersed crystallize size of 4.6 nm. The optimum degradation conditions of coal tar wastewater were as follows: current density of 90 mA cm^-2, electrode gap of 1 cm and temperature at 25 °C with flow velocity of 80 L h^-1. The chemical oxygen demand (COD) removal efficiency reached 92.39% after 240 min of degradation under the optimized conditions and the after-treatment COD value was 379.51 mg L^-1 which was lower than the centralized emission standard (less than 400 mg L^-1). These findings demonstrated the feasibility and efficiency of electrocatalytically degrading coal tar wastewater by BA-PbO₂ electrodes. The possible mechanism and pathway for phenol a specific pollutant in coal tar wastewater were investigated by quantum chemistry calculations (Multiwfn) and gas chromatography-mass spectrometry (GC-MS). The toxicity of each intermediate was predicted by the ECOSAR program.

Evaluation of diclofenac degradation effect in "active" and "non-active" anodes: A new consideration about mineralization inclination

This work investigates the electrochemical oxidation (EO) of diclofenac (DCF) in water with Ti/Ti₄O₇, Ti/Ru-Ir, Ti/Sb-SnO₂ and Ti/PbO₂ electrodes. Scanning electron microscope and X-ray diffraction results suggest that Ti/Ti₄O₇ has porous stacked surface morphology and Ti/Sb-SnO₂ possesses the smallest grain size. Linear sweep voltammetry test results indicate that PbO₂ has the highest oxygen evolution potential, while Ti/Ti₄O₇ and Ti/Ru-Ir show better oxygen evolution activity. DCF degradation results reveal that PbO₂ possessed the highest DCF removal (R_DCF = 99.2%) and chemical oxygen demand (COD) removal (R_COD = 97.0%), the fastest COD degradation rate (k = 0.0275 min^-1, R² = 0.964), the lowest specific energy consumption (EC_DCF = 1.81 kWh^.g DCF^-1, EC_TOC = 6.90 kWh^.g TOC^-1). The toxicity variation of DCF during EO process on PbO₂ is rise first and then to fall. Considering the differences of the four electrodes in residual, conversion and mineralization aspects, mineralization selectivity (MS) was proposed to estimate the mineralization inclination of electrodes during EO process, and PbO₂ displays the strongest mineralization inclination (MS = 0.594). In addition, the possible degradation pathway of DCF on PbO₂ electrode indicates a composite behavior of conversion and mineralization. All of them above indicate the promising application potential of PbO₂ in lower concentration pharmaceuticals and personal care products wastewater treatment. Moreover, MS could be employed as a supplementary index to assess the different inclinations of this composite behavior on various electrodes used for electrochemical treatment of organics in later studies.