Highly efficient uranium (VI) capture from aqueous solution by means of a hydroxyapatite-biochar nanocomposite: Adsorption behavior and mechanism

Ultra-high capacity and selectivity for uranium fixation by carbon nanosphere supported hydroxyapatite nanorod adsorbent

Uranium (U(VI)) has chemical and radiological toxicity, so the effective treatment of uranium-containing wastewater is crucial for both environmental safety and human health. Here, a carbon nanosphere (CNS) supported hydroxyapatite (HAP) nanorod (HAP/CNS) adsorbent was prepared using a simple glucose-assisted hydrothermal method toeffectively immobilize U(VI). Glucose not only derived CNS, but also facilitated HAP crystallization, prohibited HAP aggregation, and introduced oxygen-containing functional groups (i.e., COOH). The optimized HAP/CNS possessed a fantastic adsorption capability of 3080.3 mg/g for U(VI), nearly three times that of HAP and much higher than many reported HAP-based adsorbents. Notably, HAP/CNS was less affected by coexisting ions (distribution coefficient, Kd, researched 6.0 × 104 mL/g) and humic acid, and maintained good capability for real wastewater. The pseudo-second-order kinetic model and Langmuir isotherm model could better explain U(VI) removal behavior by HAP/CNS. Results showed that HAP/CNS and UO22+ combined to form a new uranium-containing compound, i.e., calcium-uranium mica (Ca(UO2)2(PO4)2·3H2O) via ion exchange and dissolution-precipitation, which should be the main reason for the ultra-high capacity and selectivity of HAP/CNS. Additionally, the hydrophilic oxygen-containing functional groups synergistically facilitated U(VI) fixation through complexation. This work introduces a superior adsorbent for purifying uranium-contaminated wastewater and elucidates its synergetic mechanism in uranium fixation.

Bionic polydopamine in-situ functionalized keratin double network gel with adsorption and self-adaptability: promoting uranium entrapment from seawater

Adsorption behavior driven by surface charge is a challenge for uranyl extraction from seawater (UES), so it is attractive to design uranium adsorbents with charge and environment self-adaptability. In this paper, polyphenolamine (PPA) with a dopamine-like structure was synthesized by a one-step method using tannic acid (TA) and polyethyleneimine (PEI) as raw materials. The PPA with different isoelectric points are obtained by adjusting the ratios of TA and PEI, which enables the charge regulation of PPA within pH 6-9. Then, based on the excellent adhesion of PPA, a novel double network PPA-HK aerogel was constructed by the spatial crosslinking strategy between PPA and keratin peptides. It not only realizes the transformation of PPA from dispersed to condensed state, but also endows PPA-HK with the charge-driven regulable adsorption behavior. When the ratio of TA and PEI was 1:2, the maximum adsorption capacity of PPA-HK (265 mg g-1) was achieved at pH = 8 which was exactly the pH of natural seawater. The saturated adsorption capacity of PPA-HK reached 8.05 mg g-1 after 25 days of adsorption in natural seawater, as well as it exhibited excellent recyclability and antibacterial performance (with an antibacterial rate of over 90 %). What is more important is that it still maintains high mechanical strength. The in-situ spatial crosslinking strategy is used in the modification of keratin by using polydopamine-like PPA for the first time. This study not only endues the adsorbent multi properties, but also expands the application potential of keratin in uranium extraction.

Recent approaches and advancement in biochar-based environmental sustainability: Is biochar fulfilling the sustainable development goals?

This review highlights the application of biochar (BC) for attaining different SDGs (SDG 6: clean water and sanitation, SDG 7: affordable and clean energy, SDG 13: climate action, and SDG 15: life on land). These goals coincide with the various existing environmental problems including wastewater treatment, soil amendment, greenhouse gas remediation, and bioenergy generation. So, the review encompasses the various mechanisms involved in the BC-assisted treatment and reclamation of water, pollutant immobilization and enhancing soil properties, reduction of greenhouse gas emission during the wastewater treatment process and soil amendment mechanisms, bioenergy generation through various electrode material, biodiesel production, and many more. The review also explains the various drawbacks and limitations of BC application to the available environmental issues. Conclusively, it was apprehended that BC is an appropriate material for several environmental applications. More research interventions are further required to analyze the applicability of different BC materials for attaining other available SDGs.

Hydroxyapatite derived from eggshell embedded on functionalized g-C3N4 for synergistic extraction of U(VI) from aqueous solution

In this paper, we report hydroxyapatite derived from egg-shell biowaste embedded on diglycolamic acid functionalized graphitic carbon nitride nanocomposite (abbreviated as HAp@D-gCN). The compositional and morphological characteristics of HAp@D-gCN were evaluated using scanning electron microscope, X-ray diffraction, BET, FTIR techniques and surface charge using zeta potential measurement. The sorption of U(VI) species on HAp@D-gCN was investigated through batch studies as a function of pH, contact time, initial U(VI) concentration, adsorbent dosage and ionic strength. The adsorption of U(VI) onto HAp@D-gCN was confirmed by FTIR, XRD and EDS elemental mapping. Adsorption kinetics follow pseudo second order model and it attains equilibrium within 20 min. Adsorption isotherm data correlates well with Langmuir isotherm model with a maximum sorption capacity of 993.6 mg of U(VI) per gram of HAp@D-gCN at 298K. U(VI) can be leached from the loaded adsorbent using 0.01 M Na2CO3 as desorbing agent and its sorption capacity remains unaffected even after 4 adsorption-desorption cycles. Hence, the present study reveals that HAp@D-gCN nanocomposite could serve as an environmental friendly material with potential application in environmental remediation.

Microbial etch: A novel construction method of functionalized biochar for enhanced uranium extraction in radioactive wastewater

Nuclear energy is playing an increasingly important role on the earth, but the nuclear plants leaves a legacy of radioactive waste pollution, especially uranium-containing pollution. Straw biochar with wide sources, large output, low cost, and easy availability, has emerged as a promising material for uranium extraction from radioactive wastewater, but the natural biomass with suboptimal structure and low content of functional groups limits the efficiency. In this work, microbial etch was first came up to regulate the biochar's structure and function. The surface of the biochar becomes rougher and more microporous, and the mineral contents (Ca, P) indirectly increased by microbial etch. The biochar was modified by calcium phosphate and exhibited a remarkable uranium extraction capacity of 590.8 mg g-1 (fitted value). This work provides a cost-effective and sustainable method for preparing functionalized biochar via microbial etch, which has potential for application to uranium extraction from radioactive wastewater.

A critical review on biochar for the removal of toxic pollutants from water environment

As an effort to tackle some of the most pressing ecological issues we are currently experiencing, there has been an increasing interest in employing biomass-derived char products in various disciplines. Thermal combustion of biomass results in biochar production, which is a remarkably rich source of carbon. Not only does the biochar obtained by the thermochemical breakdown of biomass lower the quantity of carbon released into the environment, but it also serves as an eco-friendly substitute for activated carbon (AC) and further carbon-containing products. An overview of using biochar to remove toxic pollutants is the main subject of this article. Several techniques for producing biochar have been explored. The most popular processes for producing biochar are hydrothermal carbonization, gasification and pyrolysis. Carbonaceous materials, alkali, acid and steam are all capable of altering biochar. Depending on the environmental domains of applications, several modification techniques are chosen. The current findings on characterization and potential applications of biochar are compiled in this survey. Comprehensive discussion is given on the fundamentals regarding the formation of biochar. Process variables influencing the yield of biochar have been summarized. Several biochars' adsorption capabilities for expulsion pollutants under various operating circumstances are compiled. In the domain of developing biochar, a few suggestions for future study have been given.

A Phosphorylated Dendrimer-Supported Biomass-Derived Magnetic Nanoparticle Adsorbent for Efficient Uranium Removal

A novel biomass-based magnetic nanoparticle (Fe3O4-P-CMC/PAMAM) was synthesized by crosslinking carboxymethyl chitosan (CMC) and poly(amidoamine) (PAMAM), followed by phosphorylation with the incorporation of magnetic ferric oxide nanoparticles. The characterization results verified the successful functionalization and structural integrity of the adsorbents with a surface area of ca. 43 m2/g. Batch adsorption experiments revealed that the adsorbent exhibited a maximum adsorption capacity of 1513.47 mg·g-1 for U(VI) at pH 5.5 and 298.15 K, with Fe3O4-P-CMC/G1.5-2 showing the highest affinity among the series. The adsorption kinetics adhered to a pseudo-second-order model (R2 = 0.99, qe,exp = 463.81 mg·g-1, k2 = 2.15×10-2 g·mg-1·min-1), indicating a chemically driven process. Thermodynamic analysis suggested that the adsorption was endothermic and spontaneous (ΔH° = 14.71 kJ·mol-1, ΔG° = -50.63 kJ·mol-1, 298. 15 K), with increasing adsorption capacity at higher temperatures. The adsorbent demonstrated significant selectivity for U(VI) in the presence of competing cations, with Fe3O4-P-CMC/G1.5-2 showing a high selectivity coefficient. The performed desorption and reusability tests indicated that the adsorbent could be effectively regenerated using 1M HCl, maintaining its adsorption capacity after five cycles. XPS analysis highlighted the role of phosphonate and amino groups in the complexation with uranyl ions, and validated the existence of bimodal U4f peaks at 380.1 eV and 390.1 eV belonging to U 4f7/2 and U 4f5/2. The results of this study underscore the promise of the developed adsorbent as an effective and selective material for the treatment of uranium-contaminated wastewater.

Redox-active phytic acid-based self-assembled hybrid material for enhanced uranium adsorption from highly acidic solution

Achieving efficient uranium adsorption from highly acidic wastewater is still considered challenging. Here, an inorganic-organic hybridized self-assembly material (rPFE-10) with redox activity was constructed by phytic acid (PA), ethylenediamine (EDA), and Fe(II) via a facile one-pot route, and further applied for U(VI) removal. In the static adsorption experiment, rPFE-10 achieved the maximum U(VI) adsorption capacity of 717.1 mg/g at the optimal pH of 3.5. It also performed preeminently in a highly acidic condition of pH = 1.0, with the highest adsorption capacity of 551.2 mg/g and an equilibrium time of 30 min. Moreover, rPFE-10 exhibited a pH-responsive adsorption selectivity for U(VI) and An-Ln (S(U(VI)) and S(An-Ln)), which increased to 69 % and 94 % respectively as pH decreased from 3.0 to 1.0. Additionally, the spectral analysis revealed a reconstruction mechanism induced by multiple synergistic adsorption, in which U(VI) exchange with EDA+/2+ and Fe2+/3+ and earned suitable coordination geometry and ligand environment to coordinate with PA (mainly P-OH), while partial U(VI) is reduced by Fe(II) in framework. This work not only highlights the facile strategy for enhanced U(VI) retention in highly acidic solution, but expands the potential application of supramolecular self-assembly material in treatment of nuclear wastewater.

High efficiency adsorption of uranium by magnesia-silica-fluoride co-doped hydroxyapatite

Hydroxyapatite has a high affinity to uranium, and element doping can effectively improve its adsorption performance. In this study, magnesia-silica-fluoride co-doped hydroxyapatite composite was prepared by hydrothermal method, and the effect of single-phase and multiphase doping on the structure and properties of the composites was investigated. The results showed that the specific surface area of Mg-Si-F-nHA composites increased by 63.01% after doping. Comparing with nHA, U(VI) adsorption capacity of Si-nHA, Mg-Si-nHA and Mg-Si-F-nHA composites increased by 13.01%, 17.39% and 22.03%, respectively. The adsorption capacity of Mg-Si-F-nHA composite reached 1286.76 mg/g. Adsorbent dosage and pH obviously affected U(VI) adsorption, and the experimental data can be fitted well by PSO and Sips models. The physicochemical characterization before and after adsorption suggested that complexation, ion exchange and precipitation participated in uranium adsorption. In conclusion, different elements doping can effectively improve the uranium adsorption properties of hydroxyapatite composites.

Combined use of biochar and phosphate rocks on phosphorus and heavy metal availability: A meta-analysis

Biochar (BC) and phosphate rocks (PR) are alternative nutrient sources with multiple benefits for sustainable agriculture. The combination of these soil amendments serves two main purposes: to increase soil phosphorus (P) availability and to remediate heavy metal (HM) contamination. However, a further demonstration of the benefits and risks associated with the combined use of BC and PR (BC + PR) is needed, considering the specific characteristics of raw materials, soil types, experimental conditions, and climatic contexts. This meta-analysis is based on data from 28 selected studies, including 581 paired combinations evaluating effects on extraction and fractionation of cadmium (Cd) and lead (Pb), and 290 paired combinations for soil labile and non-labile P. The results reveal that BC, PR, and BC + PR significantly increase soil labile and non-labile P, with BC + PR showing a 150% greater increase compared to BC alone. In tropical regions, substantial increases in P levels were observed with BC, PR, and BC + PR exhibiting increments of 317, 798, and 288%, respectively. In contrast, temperate climate conditions showed lower increases, with BC, PR, and BC + PR indicating 54, 123, and 88% rises in soil P levels. Moreover, BC, PR, and BC + PR effectively reduce the bioavailability of Cd and Pb in soil, with BC + PR demonstrating the highest efficacy in immobilizing Cd. The synergistic effect of BC + PR highlights their potential for Cd remediation. BC + PR effectively reduces the exchangeable fraction of Cd and Pb in soil, leading to their immobilization in more stable forms, such as the residual fraction. This study provides valuable insights into the remediation potential and P management benefits of BC and PR, highlighting their importance for sustainable agriculture and soil remediation practices.

Innovative Sol-gel functionalized polyurethane foam for sustainable water purification and analytical advances

Nanomaterial combined polymeric membranes such as polyurethane foams (PUFs) have garnered enormous attention in the field of water purification due to their ease of management and surface modification, cost-effectiveness, and mechanical, chemical, and thermal properties. Thus, this study reports the use of novel Sol-gel impregnated polyurethane foams (Sol-gel/PUFs) as new dispersive solid phase microextractors (d- µ SPME) for the efficient separation and subsequent spectrophotometric detection of Eosin Y (EY) textile dye in an aqueous solution with a pH of 3-3.8. The Sol gel, PUFs, and Sol gel-impregnated PUFs were characterized using scanning electron microscopy (SEM), goniometry measurements, dynamic light scattering (DLS), energy dispersive spectroscopy (EDS), UV-Visible, and FTIR spectra. Batch experiment results displayed a remarkable removal percentage (96% ± 5.4%) of the EY from the aqueous solution, with the total sorption time not exceeding 60 min. These data indicate rate-limited sorption via diffusion and/or surface complex ion associate formations after the rapid initial sorption steps. A pseudo-second order kinetic model thoroughly explained the sorption kinetics, providing a sorption capacity (qe) of 37.64 mg g-1, a half-life time (t1/2) of 0.8 ± 0.01 min, and intrinsic penetration control dye retention. The thermodynamic results revealed a negative value for ΔG⁰ (-78.07 kJ mol-1 at 293 K), clearly signifying that the dye uptake was spontaneous, as well as a negative value for ΔH⁰ (-69.58 kJ mol-1) and a positive value for ΔS⁰ (147.65 J mol-1 K-1), making clear the exothermic nature of EY adsorption onto the sorbent, with a growth in randomness at the molecular level. A ternary retention mechanism is proposed, involving the "weak base anion exchanger" of {(-CH2-OH+ -CH2-) (Dye anion)-}Sol-gel/PUF and/or {(-NH2 + -COO-) (Dye anion)-}Sol-gel/PUF via solvent extraction and "surface adsorption" of the dye anion on/in the Sol-gel/PUFs membranes in addition to H-bonding, including surface complexation and electrostatic π-π interaction, between the dye and the silicon/zirconium oxide (Si-O-Zr) and siloxane (Si-O-Si) groups on the sorbent. Complete extraction and recovery (93.65 ± 0.2, -102.28 ± 2.01) of EY dye with NaOH (0.5 M) as a proper eluting agent was achieved using a sorbent-packed mini column. In addition, the established extractor displayed excellent reusability and does not require organic solvents for EY enrichment in water samples, making it a talented nominee as a novel sorbent for EY sorption from wastewater. This study is of great consequence for expanding the applicatio1n of Sol-gel/PUFs in developing innovative spectrophotometric sensing strategies for dye determination. In view of this, it would also be remarkable to perform future studies to explore the analytical implications of this extractor regarding safety and environmental and public health issues associated to the pollutant.

Development of nanofibrous scaffolds containing polylactic acid modified with turmeric and hydroxyapatite/vivianite nanoparticles for wound dressing applications

Damaging the outer layer of the body (the skin) has been a common issue for decades. Fabrication of nanofibrous membranes via the electrospinning technique for the sake of making the wound healing process more facile has caught a lot of interest. For this purpose, a polymeric scaffold of polylactic acid (PLA) was doped with nanoparticles with different concentrations of turmeric/hydroxyapatite/vivianite/graphene oxide. The obtained membrane was tested by XRD, SEM, FTIR, and XPS. The surface topography of the scaffold has experienced changes upon adding different concentrations of the nanoparticles. The contact angle was measured by water droplets. It accentuated change in CA starting from 43.9o for pure condition of PLA to 67.7o for PLA/turmeric/vivianite. The thermogravimetric analysis (TGA) test stated that the PLA scaffold features are thermally stable in relatively high-temperature conditions initiating from room temperature to about 300 °C, meeting the maximum loss in mass of about 5 %. The cell viability was carried out in prepared vitro for the sample which contains PLA/turmeric/vivianite/GO, it was elucidated that the IC50 was around 3060 μg/ml.

Simultaneous immobilization of lead and arsenic and improved phosphorus availability in contaminated soil using biochar composite modified with hydroxyapatite and oxidation: Findings from a pot experiment

Multi-metals/metalloids contaminated soil has received extensive attention because of their adverse health effects on the safety of the food chain and environmental health. In order to provide additional insight and aid in mitigating environmental risks, a pot experiment was directed to assess the impacts of biochars derived from rice straw (BC), and modified biochars i-e., hydroxyapatite modified (HAP-BC) and oxidized biochars (Ox-BC) on the redistribution, phytoavailability and bioavailability of phosphorus (P), lead (Pb), and Arsenic (As), as well as their effects on the growth of maize (Zea mays L.) in a Lead (Pb)/Arsenic (As) contaminated soil. The results showed that HAP-BC increased the soil total and available P, compared with raw biochar and control treatment. HAP-BC improved soil properties by elevating soil pH and electric conductivity (EC). The Hedley fractionation scheme revealed that HAP-BC enhanced the labile and moderately labile P species in soil. Both HAP-BC and Ox-BC assisted in the P build-up in plant roots and shoots. The BCR (European Community Bureau of Reference) sequential extraction data for Pb and As in soil showed the pronounced effects of HAP-BC towards the transformation of labile Pb and As forms into more stable species. Compared with control, HAP-BC significantly (P ≤ 0.05) decreased the DTPA-extractable Pb and As by 55% and 28%, respectively, subsequently, resulting in reduced Pb and As plant uptakes. HAP-BC application increased the plant fresh and dry root/shoot biomass by 239%, 72%, 222% and 190%, respectively. The Pb/As immobilization by HAP-BC was mainly driven by precipitation, ion exchange and surface complexation mechanisms in soil. In general, HAP-BC application indicated a great capability to be employed as an effective alternative soil amendment for improving P acquisition in soil, simultaneously immobilizing Pb and As in the soil-plant systems.

Efficacy and mechanisms of δ-MnO2 modified biochar with enhanced porous structure for uranium(VI) separation from wastewater

Even though uranium (U) is considered to be an essential strategic resource with vital significance to nuclear power development and climate change mitigation, U exposure to human and ecological environment has received growing concerns due to its both highly chemically toxic and radioactively hazardous property. In this study, a composite (M-BC) based on Ficus macrocarpa (banyan tree) aerial roots biochar (BC) modified by δ-MnO2 was designed to separate U(VI) from synthetic wastewater. The results showed that the separation capacity of M-BC was 61.53 mg/g under the solid - liquid ratio of 1 g/L, which was significantly higher than that of BC (12.39 mg/g). The separation behavior of U(VI) both by BC and M-BC fitted well with Freundlich isothermal models, indicating multilayer adsorption occurring on heterogeneous surfaces. The reaction process was consistent with the pseudo-second-order kinetic model and the main rate-limiting step was particle diffusion process. It is worthy to note that the removal of U(VI) by M-BC was maintained at 94.56% even after five cycles, indicating excellent reusability and promising application potential. Multiple characterization techniques (e.g. Scanning Electron Microscope-Energy Dispersive Spectrometer (SEM-EDS), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), Brunauer-Emmett-Teller (BET) and X-ray Photoelectron Spectroscopy (XPS)) uncovered that U(VI) complexation with oxygen-containing functional groups (e.g. O-CO and Mn-O) and cation exchange with protonated ≡MnOH were the dominant mechanisms for U(VI) removal. Application in real uranium wastewater treatment showed that 96% removal of U was achieved by M-BC and more than 92% of co-existing (potentially) toxic metals such as Tl, Co, Pb, Cu and Zn were simultaneously removed. The work verified a feasible candidate of banyan tree aerial roots biowaste based δ-MnO2-modified porous BC composites for efficient separation of U(VI) from uranium wastewater, which are beneficial to help address the dilemma between sustainability of nuclear power and subsequent hazard elimination.

Soil science and environmental research

As indicated in the call for papers posted for this Special Issue, Soil Science deals with various environmental compartments, so it is closely related to Environmental Research. It is clear that synergisms and collaboration are keys to reach the most fruitful relations among different sciences and scientists, and especially in all that focused on the Environment. In this line, considering Soil Science, Environmental Research, and the multiple and complex eventual combinations involving them, could give new highly interesting works focused on any of the specific subjects covered, as well as on relations among these sciences. The main objective should be going further in positive interactions that could help in protecting the Environment, proposing solutions to face hazards that are drastically threatening our planet. In view of that, the Editors of this Special Issue invited researchers to submit high-quality manuscripts including new experimental data, as well as scientifically founded discussion and reflections on the matter. The VSI has received 171 submissions, with 27% of them being accepted after peer-review. The Editors think that the papers included in this VSI have high scientific value and provide scientific knowledge on the field. In this editorial piece the Editors include comments and reflections on the papers published in the SI.

Fabrication of phosphoric-crosslinked chitosan@g-C3N4 gel beads for uranium(VI) separation from aqueous solution

In this work, a novel g-C₃N₄ filled, phosphoric-crosslinked chitosan gel bead (P-CS@CN) was successfully prepared to adsorb U(VI) from water. The separation performance of chitosan was improved by introducing more functional groups. At pH 5 and 298 K, the adsorption efficiency and adsorption capacity could reach 98.0 % and 416.7 mg g^-1, respectively. After adsorption, the morphological structure of P-CS@CN did not change and adsorption efficiency remained above 90 % after 5 cycles. P-CS@CN exhibited an excellent applicability in water environment based on dynamic adsorption experiments. Thermodynamic analyses demonstrated the value of ΔG, manifesting the spontaneity of U(VI) adsorption process on P-CS@CN. The positive values of ΔH and ΔS showed that the U(VI) removal behavior of P-CS@CN was an endothermic reaction, indicating that the increase of temperature was great benefit to the removal. The adsorption mechanism of P-CS@CN gel bead could be summarized as the complexation reaction with the surface functional groups. This study not only developed an efficient adsorbent for the treatment of radioactive pollutants, but also provided a simple and feasible strategy for the modification of chitosan-based adsorption materials.

Remediation of uranium-contaminated alkaline soil by rational application of phosphorus fertilizers: Effect and mechanism

In alkaline soil, abundant carbonates will mobilize uranium (U) and increase its ecotoxicity, which is a serious threat to crop growth. However, the knowledge of U remediation in alkaline soils remains very limited. In this study, U-contaminated alkaline soil (tillage layer) was collected from the Ili mining area of Xinjiang, the soil remediation was carried out by using phosphorus (P) fertilizers of different solubility (including KH₂PO₄, Ca(H₂PO₄)₂, CaHPO₄, and Ca₃(PO₄)₂), and the pathways and mechanisms of U passivation in the alkaline soil were revealed. The results showed that water-soluble P fertilizers, KH₂PO₄ and Ca(H₂PO₄)₂, were highly effective at immobilizing U, and significantly reduced the bioavailability of soil U. The exchangeable U was reduced by 70.5 ± 0.1% (KH₂PO₄) and 68.2 ± 1.9% (Ca(H₂PO₄)₂), which was converted into the Fe-Mn oxide-bound and residual phases. Pot experiments showed that soil remediation by KH₂PO₄ significantly promoted crop growth, especially for roots, and reduced U uptake in crops by 94.5 ± 1.0%. The immobilization of U by KH₂PO₄ could be attributed to the release of phosphate anions, which react with the uranyl ion (UO₂²⁺) forming a stable mineral of meta-ankoleite and enhancing the binding of UO₂²⁺ to the soil Fe-Mn oxides. In addition, KH₂PO₄ dissolution produces acidity and P fertilizer, which can reduce soil alkalinity and improve crop growth. The findings in this work demonstrate that a rational application of P fertilizer can effectively, conveniently, and cheaply remediate U contamination and improve crop yield and safety on alkaline farmland.

Synergy of surface adsorption and intracellular accumulation for removal of uranium with Stenotrophomonas sp: Performance and mechanisms

Uranium is well-known to have serious adverse effects on the ecological environment and human health. Bioremediation stands out among many remediation methods owing to its being economically feasible and environmentally friendly. This study reported a great promising strategy for eliminating uranium by Stenotrophomonas sp. CICC 23833 in the aquatic environment. The bacterium demonstrated excellent uranium adsorption capacity (q_max = 392.9 mg/g) because of the synergistic effect of surface adsorption and intracellular accumulation. Further analysis revealed that hydroxyl, carboxyl, phosphate groups and proteins of microorganisms were essential in uranium adsorption. Intracellular accumulation was closely related to cellular activity, and the efficiency of uranium processing by the permeabilized bacterial cells was significantly improved. In response to uranium stress, the bacterium was found to release multiple ions in conjunction with uranium adsorption, which facilitates the maintenance of bacterial life activities and the conversion of uranyl to precipitates. These above results indicated that Stenotrophomonas sp. Had great potential application value for the remediation of uranium.

Multicomponent adsorption of heavy metals onto biogenic hydroxyapatite: Surface functional groups and inorganic mineral facilitating stable adsorption of Pb(Ⅱ)

Due to the coexistence of various heavy metals in the contaminated environment, it is essential to comprehensively study the multicomponent adsorption of heavy metals in order to tackle these combined pollutants. Herein, the adsorption processes of Pb(Ⅱ), Cu(Ⅱ) and Cd(Ⅱ) by biogenic hydroxyapatite (BHAp) were investigated in single and multicomponent systems. The maximum adsorption capacity for Pb(Ⅱ), Cu(Ⅱ) and Cd(Ⅱ) by BHAp in single system reached 311.16, 82.05 and 92.54 mg g^-1, respectively, while adsorption capacity for Cu(Ⅱ) and Cd(Ⅱ) in multicomponent system decreased more obviously than that of Pb(Ⅱ). Furthermore, the stability of Cu(Ⅱ) and Cd(Ⅱ) adsorbed on BHAp was indeed influenced in multicomponent system. By means of the characterization analysis, it was found that ion exchange was more instrumental in the adsorption processes of Cu(Ⅱ) and Cd(Ⅱ) in single system than in multicomponent system. Significantly, it was observed that the proportion of generally stable Pb(II) adsorbed on BHAp exceeded 95% in both single and multicomponent systems. This result might be due to the in-site growth of stable crystals of Pb_xCa_10-x(PO₄)₆(OH)₂, which was synergistically induced by surface functional groups and inorganic mineral of BHAp, and was unaffected by the coexistence of Cu(Ⅱ) and Cd(Ⅱ).

Efficient uranium(VI) adsorbing bioinspired nano-sized hydroxyapatite composites: synthesis, tuning, and adsorption mechanism

The production of large amounts of uranium-containing wastewater and its potential hazards has stimulated green and efficient material removal of uranium (VI). Inspired by the natural mineralization of bone, a facile and eco-friendly biomimetic synthesis of nano-hydroxyapatite (HAP) was carried out using chitosan (CS) as a template. It was found that the reaction temperature and the amount of precursors influence the particle size, crystallinity and specific surface area of the CS/HAP nanorods, and consequently their U(VI) adsorption efficiency. Moreover, the synthesized CS/HAP-40 with smaller particle size, lower crystallinity, and larger specific surface area show a more efficient U(VI) removal compared with CS/HAP-55 and CS/HAP-55-AT. It has a maximum adsorption capacity of 294.12 mg·g^-1 of the CS/HAP-40. Interestingly, the U(VI) removal mechanism of CS/HAP-40 in acidic (pH = 3) and alkaline (pH = 8) aqueous solutions was found to be different. As one of the main results, the U(VI) adsorption mechanisms at pH 8 could be surface complexation and ion exchange. On the contrary, three different mechanisms could be observed at pH 3: dissolution-precipitation to form chernikovite, surface complexation, and ion exchange.

High Efficiency Uranium(VI) Removal from Wastewater by Strong Alkaline Ion Exchange Fiber: Effect and Characteristic

In this study, we analyzed the removal efficiency of uranium(U(VI)) in wastewater at relatively low concentrations using strong alkaline ion exchange fiber (SAIEF). Static tests showed that the strong alkali fibers can purify U(VI) containing wastewater in a concentration range of 20-100 mg L^-1 with an optimal pH of 10.5 and contact time of 15-30 min. Adsorption and desorption cycling tests indicated that, adsorbed uranium is easily desorbed by 0.1 mol L^-1 HCl, and the fiber still maintained the original adsorption efficiency after eight cycles. According to dynamic penetration test results, the SAIEF saturation adsorption capacity was 423.9 mg g^-1, and the effluent concentration of uranium through two series columns was less than 0.05 mg L^-1, reaching the national standard for non-receiving water (GB23727-2009) SEM-EDS and FTIR analysis revealed that the functional group of SAIEF is CH₂N⁺(CH₃)₃Cl^-. Addotionally, the major forms of fiber exchange adsorption are (UO₂)₂CO₃(OH)₃^-, UO₂(CO)₃^4- and UO₂(OH)₃^-. The results indicate that the SAIEF is an excellent material for uranium removal.

In situ synthesis of magnesium-doped hydroxyapatite aerogel for highly efficient U(VI) separation with ultra high adsorption capacity and excellent recyclability

Mg-doped HAP aerogel (MHAPA) was firstly in situ prepared via freeze-drying-calcination technology to capture U(VI). The U(VI) removal capacity by MHAPA even arrived 2685.6 mg g^-1, which was about 2 times over purchased HAP, illustrating that the incorporation of Mg ions could greatly enhance the U(VI) removal capacity. Compared with HAP, MHAPA also showed better anti-ion interference ability and dynamic removal performances. In comparison with other HAP-based adsorbents, MHAPA possessed good recyclability and its desorption rate was up to 93.4% in the first cycle. The excellent U(VI) removal performances of MHAPA might be owing to its low crystallinity and grain size, fast ion exchange rate and partial ionization under acidic conditions, which would accelerate the process of electrostatic attraction, ion-exchange, and complexation to immobilize U(VI). To sum up, the prepared MHAPA was expected to be an environmentally friendly, recyclable and effective adsorbent to immobilize U(VI) in actual wastewater.

Biochar for the removal of contaminants from soil and water: a review

Biochar shows significant potential to serve as a globally applicable material to remediate water and soil owing to the extensive availability of feedstocks and conducive physio-chemical surface characteristics. This review aims to highlight biochar production technologies, characteristics of biochar, and the latest advancements in immobilizing and eliminating heavy metal ions and organic pollutants in soil and water. Pyrolysis temperature, heat transfer rate, residence time, and type of feedstock are critical influential parameters. Biochar’s efficacy in managing contaminants relies on the pore size distribution, surface groups, and ion-exchange capacity. The molecular composition and physical architecture of biochar may be crucial when practically applied to water and soil. In general, biochar produced at relatively high pyrolysis temperatures can effectively manage organic pollutants via increasing surface area, hydrophobicity and microporosity. Biochar generated at lower temperatures is deemed to be more suitable for removing polar organic and inorganic pollutants through oxygen-containing functional groups, precipitation and electrostatic attraction. This review also presents the existing obstacles and future research direction related to biochar-based materials in immobilizing organic contaminants and heavy metal ions in effluents and soil.

Graphical Abstract

Uranium biosorption by hydroxyapatite and bone meal: evaluation of process variables through experimental design

Biosorption has been examined for the treatment of aqueous solutions containing uranium, a radiotoxic pollutant. Nevertheless, the evaluation of the role of process variables by experimental design on the use of hydroxyapatite and bone meal as biosorbents for uranium has not yet been previously addressed. In this study, the effects of adsorbent dosage (M), initial uranium concentrations ([U]0), and solution pH were investigated, using a two-level factorial design and response surface analysis. The experiments were performed in batch, with [U]0 of 100 and 500 mg L-1, pH 3 and 5, and adsorbent/uranium solution ratios of 5 and 15 g L-1. Contact time was fixed at 24 h. Removal rates were higher than 88%, with a maximum of 99% in optimized conditions. [U]0 and M were found to be the most influential variables in U removal in terms of adsorption capacity (q). The experiments revealed that bone meal holds higher adsorption capacity (49.87 mg g-1) and achieved the highest uranium removal (~ 100%) when compared to hydroxyapatite (q = 49.20 mg g-1, removal = 98.5%). The highest value of q for both biomaterials was obtained for [U]0 = 500 mg L-1, pH 3, and M = 5 g L-1. Concerning the removal percentage, bone meal achieved the best performance for [U]0 = 500 mg L-1, pH 3, and M = 15 g L-1. Further experiments were made with real radioactive waste, resulting in a high uranium adsorption capacity for both materials, with 22.11 mg g-1 for hydroxyapatite and 22.08 mg g-1 for bone meal, achieving uranium removal efficiencies higher than 99%.

Nano-hydroxyapatite modified biochar: Insights into the dynamic adsorption and performance of lead (II) removal from aqueous solution

Adsorption of lead as Pb(II) using biochar is an environmentally sustainable approach to remediate this kind of pollution affecting wastewater. In this study, rice straw biochar (BC) was modified by combination with nano-hydroxy-apatite (HAP), resulting in a material designated as BC@nHAP, with enhanced adsorption performance. Based on Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses, it was evidenced that, after modification, HAP greatly enhanced surface functional groups (i.e., -COOH and/or -OH) of raw biochar's surface. Batch tests showed that the maximum sorption capacity of BC (63.03 mg g^-1) was improved due to the modification, reaching 335.88 mg g^-1 in BC@nHAP. Pseudo-second order (PSO) kinetics fitted well the adsorption data (R² = 0.99), as well as the Langmuir isotherm model (showing an adsorption value of 335.88 mg g^-1 for q_e). The results of thermodynamic calculations showed that the adsorption was primarily governed by chemisorption process. FTIR spectroscopy and XPS spectrum after adsorption further confirmed that the adsorption mechanisms were ion exchange with Pb²⁺ and surface complexation by -OH and -COOH. In addition, BC@nHAP revealed a brilliant regeneration capability. The maximum adsorption capacity by BC@nHAP was higher than that of raw biochar or other previously reported adsorbents. Therefore, BC@nHAP could be seen as a new sorbent material with high potential for real-scale heavy metal removal from wastewater, and specifically as a capable candidate new sorbent for Pb(II) removal from wastewater, which has clear implications as regard preservation of environmental quality and public health.

Oxygen-containing groups in cellulose and lignin biochar: their roles in U(VI) adsorption

The adsorption behaviors of cellulose and lignin biochar depend on the evolution of their oxygen-containing groups to some extent. In this study, cellulose-rich pakchoi and lignin-rich corncob were selected to prepare the pyrolytic biochar at variable temperatures, named PBC and CBC, respectively. Their structure-function relationships were in-depth studied via the combination of the adsorption experiments of U(VI) and comprehensive spectral analyses. The maximal adsorption capacity of PBC 300, obtained at 300 °C, was measured as 46.62 mg g^-1 for U(VI), which was ⁓1.3 times higher than 35.60 mg g^-1 of CBC 300. U(VI) adsorption on PBC and CBC were predominantly ascribed to the coordination interaction between oxygen-containing groups and U(VI). Interestingly, the main complexation groups were distinct in both biochars due to the different inherent evolutions of cellulose and lignin. Volatile d-glucose chains in cellulose were apt to degrade rapidly, and the formed carboxyls acted as the most important sites in PBC. However, the stable aromatic network in lignin led to a slow degradation, and more hydroxyls thus remained in CBC, which controlled U(VI) adsorption. In this study, we obtained greatly cost-effective adsorbents of U(VI) and provided some essential insights into understanding the structural evolution-function relationship of cellulose and lignin biochar.

High-speed and efficient removal of uranium (VI) from aqueous solution by hydroxyapatite-modified ordered mesoporous carbon (CMK-3)

In recent years, the synthesis and application of green, cost-effective, and sustainable materials for uranium (VI) removal was significant to environmental protection. The ordered mesoporous carbon (CMK-3) supported different mass of hydroxyapatite materials (HAP@CMK-3) were facilely synthesized via hydrothermal method. The resultant materials were characterized by XRD, FT-IR, BET, SEM, TEM mapping, and XPS, and implemented for immobilizing U(VI). Not only the specific surface area of HAP (7.01 m²/g) was increased by the loading on CMK-3 (818.37 m²/g), but also the adsorption capacity of CMK-3 was increased by HAP modification. Impressively, HAP@CMK-3 exhibited highly adsorption capacity of U(VI) with the increase of HAP deposition and was capable of achieving fast reaction. Therein to, the specific surface area of HAP@CMK-3(2:1) was 253.68 m²/g, as well as the adsorption capacity was up to 1072 mg/g (fitted by Langmuir isotherm, at pH=3.0, 298 K) and the adsorption process was completed in 30 min (followed by pseudo-second-order kinetic). The adsorption mechanisms of U(VI) on HAP@CMK-3 involved electrostatic forces, ionic interactions, and chemical complexation. This work offered new avenues to address the limitations of cost and less secondary pollution for the removal of U(IV) from wastewater.

Surface ion-imprinted brewer's spent grain with low template loading for selective uranyl ions adsorption from simulated wastewater

Efficient removal of uranyl ions from wastewater requires excellent selectivity of the adsorbents. Herein, we report a new strategy using a high monomer/template molar ratio of 500:1 to prepare surface ion-imprinted brewer's spent grain (IIP-BSG) for selective U(VI) removal using binary functional monomers (2-hydroxyethyl methacrylate and diethyl vinylphosphonate) with high site accessibility and easy template removal. IIP-BSG exhibits a maximum U(VI) adsorption capacity of 165.7 mg/g, a high selectivity toward U(VI) in the presence of an excess amount of Eu(III) (Eu/U molar ratio = 20), a good tolerance of salinity, and a high reusability. In addition, mechanism studies have revealed electrostatic interaction and a coordination of uranyl ions by carboxyl and phosphoryl groups, the predominant contribution of high-energy (specific) sites during selective adsorption, and internal mass transfer as the rate-controlling step of U(VI) adsorption. Furthermore, IIP-BSG shows great potentials to separate U(VI) from lanthanides in simulated nuclear wastewater (pH₀ = 3.5) and selectively concentrate U(VI) from simulated mine water (pH₀ = 7.1). This study proves that the ion-imprinting effect can be achieved using a very low template amount with reduced production cost and secondary pollution, which benefits large-scale promotion of the ion-imprinted materials for selective uranyl ions removal.

The Adsorption Potential of Cr from Water by ZnO Nanoparticles Synthesized by Azolla pinnata

Aqueous solutions containing toxic elements (TEs) (such as hexavalent chromium (Cr (VI)) can be toxic to humans even at trace levels. Thus, removing TEs from the aqueous environment is essential for the protection of biodiversity, hydrosphere ecosystems, and humans. For plant fabrication of zinc oxide nanoparticles (PF-ZnONPs), Azolla pinnata plants were used, and X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), SEM, and FTIR techniques were used for the identification of PF-ZnONPs and ZnONPs, which were used to remove Cr (VI) from aqueous solution. A number of adsorption parameters were studied, including pH, dose, concentration of metal ions, and contact time. The removal efficiency of PF-ZnONPs for Cr (VI) has been found to be 96% at a time (60 min), 69.02% at pH 4, and 70.43% at a dose (10 mg·L⁻¹). It was found that the pseudo-second-order model best described the adsorption of Cr (VI) onto PF-ZnONPs, indicating a fast initial adsorption via diffusion. The experimental data were also highly consistent with the Langmuir isotherm model calculations.

A green method for removing chromium (VI) from aqueous systems using novel silicon nanoparticles: Adsorption and interaction mechanisms

In the present study, we used the horsetail plant (Equisetum arvense) as a green source to synthesize silicon nanoparticles (GS-SiNPs), considering that it could be an effective adsorbent for removing chromium (Cr (VI)) from aqueous solutions. The characterization of GS-SiNPs was performed via Brunauer-Emmett-Teller (BET), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and X-ray photo electron spectroscopy (XPS) techniques. The batch test results of Cr (VI) adsorption on GS-SiNPs showed a high adsorption capacity, reaching 87.9% of the amount added. The pseudo-second order kinetic model was able to comprehensively explain the adsorption kinetics and provided a maximum Cr (VI) adsorption capacity (Q_e) of 3.28 mg g^-1 (R² = 90.68), indicating fast initial adsorption by the diffusion process. The Langmuir isotherm model fitted the experimental data, and accurately simulated the adsorption of Cr (VI) on GS-SiNPs (R² = 97.79). FTIR and XPS spectroscopy gave further confirmation that the main mechanism was ion exchange with Cr and surface complexation through -OH and -COOH. Overall, the results of the research can be of relevance as regards a green and new alternative for the removal of Cr (VI) pollution from affected environments.

Explorations on efficient extraction of uranium with porous coal fly ash aerogels

In order to explore a suitable uranium adsorbent with the advantages of low-cost, recyclability and high efficiency, porous coal fly ash aerogels with different size of coal fly ash were synthesized. Among them, PCFAA-1250 (prepared with 1250 mesh coal fly ash (CFA)) showed better adsorption performance and the maximum adsorption efficiency even approached 96.5% (C₀ = 10 mg L^-1, m/V = 1.0 g L^-1, T = 298 K, t = 24 h and pH = 3.0), which was higher than most of previous adsorbents. Langmuir and pseudo-second-order models were more likely to be used to determine the removal behavior of uranium on PCFAA, illustrating that the adsorption reaction was uniform chemisorption. Meanwhile, the adsorption process on PCFAA was spontaneous. Notably, the desorption efficiencies of all of PCFAA were more than 80% after five cycles, which suggested that PCFAA possessed good recyclability, especially PCFAA-1250. Besides, the adsorption mechanism was further revealed via XPS and the uranium ions were immobilized on the surface of adsorbents through complexation. Based on above conclusions, it could be concluded that PCFAA-1250 had the potential to be a candidate for the extraction of uranium from wastewater.

Effective Adsorption of Colorants from Sugarcane Juice by Bagasse-Based Biochar-Hydroxyapatite Composite

The clarification of sugarcane juice is a crucial stage in the sugar manufacturing process, as it affects evaporator performance, sugar quality and yield. The emergence of environmentally friendly and efficient adsorption technology has resulted in widespread interest in carbon-based materials. However, their low adsorption capacity and reusability make them unsuitable for processing sugarcane juice. Here, we provide a cost-effective and sustainable method to dope hydroxyapatite (HAP) nanoparticles on porous carbon (BBC) derived from sugarcane bagasse (BBC-HAP). The composite shows excellent adsorption capacity for color extract from sugarcane juice of 313.33 mg/g, far more effective than the commercially available carbon-based adsorbents. Isotherm studies show that the adsorption of BBC-HAP composite to the colorants is a monolayer process. The pseudo-first-order (PFO) and pseudo-second-order (PSO) kinetic models demonstrate that the adsorption process is dominated by chemisorption and supplemented by physical adsorption.

Herbal plants- and rice straw-derived biochars reduced metal mobilization in fishpond sediments and improved their potential as fertilizers

Fishpond sediments are rich in organic carbon and nutrients; thus, they can be used as potential fertilizers and soil conditioners. However, sediments can be contaminated with toxic elements (TEs), which have to be immobilized to allow sediment reutilization. Addition of biochars (BCs) to contaminated sediments may enhance their nutrient content and stabilize TEs, which valorize its reutilization. Consequently, this study evaluated the performance of BCs derived from Taraxacum mongolicum Hand-Mazz (TMBC), Tribulus terrestris (TTBC), and rice straw (RSBC) for Cu, Cr, and Zn stabilization and for the enhancement of nutrient content in the fishpond sediments from San Jiang (SJ) and Tan Niu (TN), China. All BCs, particularly TMBC, reduced significantly the average concentrations of Cr, Cu, and Zn in the overlying water (up to 51% for Cr, 71% for Cu, and 68% for Zn) and in the sediments pore water (up to 77% for Cr, 76% for Cu, and 50% for Zn), and also reduced metal leachability (up to 47% for Cr, 60% for Cu, and 62% for Zn), as compared to the control. The acid soluble fraction accounted for the highest portion of the total content of Cr (43-44%), Cu (38-43%), and Zn (42-45%), followed by the reducible, oxidizable, and the residual fraction; this indicates the high potential risk. As compared with the control, TMBC was more effective in reducing the average concentrations of the acid soluble Cr (15-22%), Cu (35-53%), and Zn (21-39%). Added BCs altered the metals acid soluble fraction by shifting it to the oxidizable and residual fractions. Moreover, TMBC improved the macronutrient status in both sediments. This work provides a pathway for TEs remediation of sediments and gives novel insights into the utilization of BC-treated fishpond sediments as fertilizers for crop production.

Simple one-pot synthesis of manganese dioxide modified bamboo-derived biochar composite for uranium(VI) removal

Exploitation of bamboo-derived biochar offers a lucrative opportunity for using moso bamboo due to its short growth cycle, large quantity and universality. Novel MnO2 modified bamboo-derived biochar composites (MnO2@BBC) were...

Recent Progress in the Application of Hydroxyapatite for the Adsorption of Heavy Metals from Water Matrices

Wastewater treatment remains a critical issue globally, despite various technological advancements and breakthroughs. The study of different materials and technologies gained new valences in the last years, in order to obtain cheap and efficient processes, to obtain a cleaner environment for future generations. In this context, the present review paper presents the new achievements in the materials domain with highlights on apatitic materials used for decontamination of water loaded with heavy metals. The main goal of this review is to present the adsorptive removal of heavy metals using hydroxyapatite-based adsorbents, offering a general overview regarding the recent progress in this particular area. Developing the current review, an attempt has been made to give appropriate recognition to the most recent data regarding the synthesis methods and targeted pollutants, including important information regarding the synthesis methods and precursors, morphological characteristics of the adsorbent materials and effectiveness of processes.