Adsorption of copper(II) ions by keratin/PA6 blend nanofibres

Core-shell nanofibers containing L-arginine stimulates angiogenesis and full thickness dermal wound repair

Despite the advances in medicine, wound healing is still challenging and piques the interest of biomedical engineers to design effective wound dressings using natural and artificial polymers. In present study, coaxial electrospinning was employed to fabricate core-shell nanofiber-based wound dressing, with core composed of polyacrylamide (PAAm) and shell comprising 0.5 % solution of L-Arginine (L-Arg) in aloe vera and keratin (AloKr). Aloe vera and keratin were added as natural polymers to promote angiogenesis, reduce inflammation, and provide antibacterial activity, whereas PAAm in core was used to improve the tensile properties of the wound dressing. Moreover, L-Arg was incorporated in shell to promote angiogenesis and collagen synthesis. The fiber diameter of PAAm/(AloKr/L-Arg) core-shell fibers was (93.33 ± 35.11 nm) with finer and straighter fibers and higher water holding capacity due to increased surface area to volume ratio. In terms of tensile properties, the PAAm/(AloKr/L-Arg) core-shell nanofibers with tensile strength and elastic modulus of 2.84 ± 0.27 MPa and 62.15 ± 5.32 MPa, respectively, showed the best mechanical performance compared to other nanofibers tested. Furthermore, PAAm/(AloKr/L-Arg) exhibited the highest L-Arg release (87.62 ± 3.02 %) and viability of L929 cells in vitro compared to other groups. In addition, the highest rate of in vivo full thickness wound healing was observed in PAAm/(AloKr/L-Arg) group compared to other groups. It significantly enhanced the angiogenesis, neovascularization, and cell proliferation. The prepared PAAm/(AloKr/L-Arg) core-shell nanofibrous dressing could be promising for full-thickness wound healing.

Keratin protein nanofibers from merino wool yarn: a top-down approach for the disintegration of hierarchical wool architecture to extract α-keratin protein nanofibers

We report the extraction of keratin nanofibers from the medulla of a parent yarn after denaturing the cuticle and cortex microstructures of a merino wool yarn. Controlled alkaline hydrolysis, followed by high-speed blending in acetic acid, allowed for the extraction of keratin protein nanofibers with an average diameter of 25 nm and a length of less than 3 μm. SEM and AFM analyses showed the removal of cuticle cells from the yarn. FT-IR and DSC analyses confirmed the hydrolysis and denaturation of the sheet protein matrix of cuticle cells. XPS analysis provided strong evidence for the gradual removal of the epicuticle, cuticle cells, and cortex of the hierarchical wool structure with an increase in alkaline hydrolysis conditions. It was confirmed that the merino wool yarn subjected to hydrolysis under alkaline conditions exposed its internal fibrillar surface. In an acetic acid medium, these fibrillar surfaces obtained a surface charge, which further supported the defibrillation of the structure into its individual nanofibrils during high-speed blending. The extracted nanostructures constitute mainly α-helical proteins. The morphology of the nanofibers is composed of a uniform circular cross-section based on the images obtained using AFM, TEM, and SEM. The extracted nanofibers were successfully fabricated into transparent sheets that can be used in several applications.

Competitive Cation Adsorption on Electron-Irradiated Sheep Wool Changes the Fitting of Adsorption Isotherms for Single-Component Solutions

This work analyses 10 adsorption isotherm models applied to adsorption of Cr(III) and Cu(II) from binary solutions on electron-irradiated sheep wool (0-24-100) kGy. The results are compared with fitting the same adsorbates from corresponding single solutions. The competing cation significantly changes the fitting of the selected isotherms to the extent that even simultaneous fitting of the same cation in the single and binary solution is rare. In the case of Cr(III), 4 favourable matches were found out of 30 compared cases, while in the case of Cu(II), only 2 conformities were found. Having the Cr(III) coordination number exclusively of 6, but Cu(II) up to 4, 5, 6, the last coordinates more easily with the ligands provided by keratin, resulting in preferential chemisorption. If there is still a lack of cysteic acid in the wool to interact with Cr(III) also, this is adsorbed on the wool physically, too. The amount of cysteic acid increasing in the wool with the absorbed dose of energy improves the chemisorption of Cr(III), as well. It can be summarized that during competitive adsorption, Cu(II) binds by chemisorption and Cr(III) by both physisorption and chemisorption, depending on the dose of energy absorbed by the wool.

Research Progress of Water Treatment Technology Based on Nanofiber Membranes

In the field of water purification, membrane separation technology plays a significant role. Electrospinning has emerged as a primary method to produce nanofiber membranes due to its straightforward, low cost, functional diversity, and process controllability. It is possible to flexibly control the structural characteristics of electrospun nanofiber membranes as well as carry out various membrane material combinations to make full use of their various properties, including high porosity, high selectivity, and microporous permeability to obtain high-performance water treatment membranes. These water separation membranes can satisfy the fast and efficient purification requirements in different water purification applications due to their high filtration efficiency. The current research on water treatment membranes is still focused on creating high-permeability membranes with outstanding selectivity, remarkable antifouling performance, superior physical and chemical performance, and long-term stability. This paper reviewed the preparation methods and properties of electrospun nanofiber membranes for water treatment in various fields, including microfiltration, ultrafiltration, nanofiltration, reverse osmosis, forward osmosis, and other special applications. Lastly, various antifouling technologies and research progress of water treatment membranes were discussed, and the future development direction of electrospun nanofiber membranes for water treatment was also presented.

Preparation Methods and Functional Characteristics of Regenerated Keratin-Based Biofilms

The recycling, development, and application of keratin-containing waste (e.g., hair, wool, feather, and so on) provide an important means to address related environmental pollution and energy shortage issues. The extraction of keratin and the development of keratin-based functional materials are key to solving keratin-containing waste pollution. Keratin-based biofilms are gaining substantial interest due to their excellent characteristics, such as good biocompatibility, high biodegradability, appropriate adsorption, and rich renewable sources, among others. At present, keratin-based biofilms are a good option for various applications, and the development of keratin-based biofilms from keratin-containing waste is considered crucial for sustainable development. In this paper, in order to achieve clean production while maintaining the functional characteristics of natural keratin as much as possible, four important keratin extraction methods—thermal hydrolysis, ultrasonic technology, eco-friendly solvent system, and microbial decomposition—are described, and the characteristics of these four extraction methods are analysed. Next, methods for the preparation of keratin-based biofilms are introduced, including solvent casting, electrospinning, template self-assembly, freeze-drying, and soft lithography methods. Then, the functional properties and application prospects of keratin-based biofilms are discussed. Finally, future research directions related to keratin-based biofilms are proposed. Overall, it can be concluded that the high-value conversion of keratin-containing waste into regenerated keratin-based biofilms has great importance for sustainable development and is highly suggested due to their great potential for use in biomedical materials, optoelectronic devices, and metal ion detection applications. It is hoped that this paper can provide some basic information for the development and application of keratin-based biofilms.

Oxidized Biomass and Its Usage as Adsorbent for Removal of Heavy Metal Ions from Aqueous Solutions

Nowadays, very coarse wool fibers are considered waste biomass and are discarded at random or burned. Therefore, it is of actual interest to valorize coarse wool fibers as utile products. In this sense, we report herein an environmentally-friendly process for the preparation of a new material based on oxidized wool fibers and designed for efficient adsorption of heavy metals from wastewater. The morphology and the structure of the obtained product were characterized by scanning electron microscopy (SEM) coupled with an X-ray energy-dispersive module (EDX) and by Fourier-transform infrared spectroscopy (FTIR). Likewise, the performances of the oxidized wool fibers for the adsorption of heavy metal cations (Cu²⁺, Cd²⁺, Pb²⁺) from aqueous solutions were tested. The adsorption kinetics data were analyzed by applying the pseudo-first-order (PFO) and pseudo-second-order (PSO) kinetic models. The equilibrium of the adsorption process was investigated by using the Freundlich and Langmuir isotherm models. According to the Langmuir isotherms registered at 300 K, the maximum adsorption capacities of the oxidized wool were found to increase from Cu²⁺ (9.41 mg/g) and Cd²⁺ (10.42 mg/g) to Pb²⁺ (30.71 mg/g). Consequently, the removal efficiency of metal ions was found to vary in the range of 96.8–99.7%. The thermodynamic parameters (e.g., enthalpy, entropy, and Gibbs free energy) were calculated and discussed.

Effect of Copper Selenide Modification on the Conductivity of PA6, PA66, PAN, and PES Fibers

Textile production has been steadily increasing for a few decades and, as a result, the amount of industrial textile waste is also increasing. This waste can be reused as raw material to produce new functional composites. Such materials can be used for special purposes with varying combinations of physical and chemical properties by using polymers modified with thin semiconductive or electrically conductive layers of binary inorganic compounds. In this paper, a study of the possibilities of altering the properties of synthetic fiber conductivity by modification with copper selenide is presented. A two-step adsorption/diffusion method was used for the copper selenide layer forming on the surface of the fibers. The treatment process was repeated cyclically. To evaluate the morphological properties of Cu_xSe treated fibers, scanning electron microscopy (SEM) and energy dispersion X-ray (EDX) were performed. The study showed that the chosen modification method is more suitable for PA and PAN fibers. Dense layers of copper selenides were successfully formed on their surface, which significantly reduced their electrical resistance.

Mixed-Ligand Strategy for the Creation of Hierarchical Porous ZIF-8 for Enhanced Adsorption of Copper Ions

The adsorption of heavy metals using metal-organic framework-based adsorption technology has been pointed out as a promising technique for the removal of these toxic elements from water. However, their adsorption capacity needs to be enhanced. Thus, the current work reports the effect of using a mixed-ligand strategy on the MOF framework and its effect on the removal of copper ions from water by adding terephthalic acid (BDC) linker to the ZIF-8precursors (2-methylimidazole (mI) and Zn²⁺) under solvothermal synthesis, leading to the formation of a hierarchical microporous mesoporous MOF, named Zn-mI-BDC, which was characterized by SEM, EDX, XRD, TGA, BET, and FTIR. As a result, all of these techniques revealed that the addition of a controlled amount of BDC did not alter the crystallinity of ZIF-8, resulting in the creation of a pore size of 4.2 nm. The new hierarchical porous MOF was tested for the adsorption of copper and exhibited an enhanced adsorption capacity compared to pristine ZIF-8 and many other standard adsorbents. The adsorption isotherm matched well with the Langmuir isotherm model, suggesting that the adsorption process chemisorption had a dominant role in the adsorption of Cu²⁺ species. Therefore, the current work is considered as an important step toward the use of a mixed-ligand strategy in enhancing the adsorption capacity of heavy metals using MOF materials.

A comprehensive review on preparation, functionalization and recent applications of nanofiber membranes in wastewater treatment

The direct discharge of significant amounts of polluted water into water bodies causes adverse ecological and human health effects. This severe deterioration in water quality creates significant challenges to meet the growing demand for clean water. Therefore, the world urgently needs environmentally friendly advanced technology to overcome this global crisis. In this regard, nanofiber-based membrane filtration is a promising technique in wastewater remediation because of their huge surface area, extremely porous structure, amenable pore size/pore size distribution, variety of material choices, and flexibility to modification with other functional materials. However, despite their unique properties, fouling, poor mechanical properties, shrinkage, and deformation are major drawbacks of nanofiber membranes for treating wastewater. This review presents a comprehensive overview of nanofiber membranes' fabrication and function in water purification applications as well as providing novel approaches to overcoming/alleviating the mentioned disadvantages. The review first presents nanofiber membrane preparation methods, focusing on electrospinning as a versatile and viable technique alongside discussing the parameters controlling nanofiber morphology. Afterward, the functionalization of nanofiber membranes by combining them with other nanomaterials, such as metal and metal-oxide nanoparticles, carbon nanotubes, metal-organic frameworks, and biomolecules, were demonstrated and discussed. In addition, nanofiber membranes functionalized with microorganisms were highlighted. Finally, we introduced and discussed in detail the most relevant and recent advances in nanofiber applications in wastewater treatment in the context of removing different pollutants (e.g., heavy metals, nutrients, radioactive elements, pharmaceuticals, and personal care products, dyes, and pesticides). Moreover, the promising antimicrobial ability of nanofiber membranes in removing microorganisms from wastewater has been fully underscored. We believe this comprehensive review could provide researchers with preliminary data and guide both researchers and producers engaged in the nanofiber membrane industry, letting them focus on the research gaps in wastewater treatment.

Recent Progress on Nanomaterial-Based Membranes for Water Treatment

Nanomaterials have emerged as the new future generation materials for high-performance water treatment membranes with potential for solving the worldwide water pollution issue. The incorporation of nanomaterials in membranes increases water permeability, mechanical strength, separation efficiency, and reduces fouling of the membrane. Thus, the nanomaterials pave a new pathway for ultra-fast and extremely selective water purification membranes. Membrane enhancements after the inclusion of many nanomaterials, including nanoparticles (NPs), two-dimensional (2-D) layer materials, nanofibers, nanosheets, and other nanocomposite structural materials, are discussed in this review. Furthermore, the applications of these membranes with nanomaterials in water treatment applications, that are vast in number, are highlighted. The goal is to demonstrate the significance of nanomaterials in the membrane industry for water treatment applications. It was found that nanomaterials and nanotechnology offer great potential for the advancement of sustainable water and wastewater treatment.

A critical review on the electrospun nanofibrous membranes for the adsorption of heavy metals in water treatment

Electrospun nanofibrous membranes (ENFMs) have many superior advantages, such as large specific surface area, high porosity, easy modification, good flexibility, and easy separation for recycling, which are consider as excellent adsorbents. In this paper, the research progress in the adsorption of heavy metals in water treatment by ENFMs is reviewed. Three types of ENFMs, including organic polymer ENFMs, organic polymer/inorganic material composite ENFMs and inorganic ENFMs are summarized, and their adsorption capacities for heavy metals in water are compared. The adsorption selectivity and capacity of ENFMs for heavy metals are depended largely on the type and number of functional groups on the surface of membranes, and usually the more the functional groups, the higher the adsorption capacity. The adsorption mechanisms of ENFMs are also mainly determined by the type of functional groups on the membrane. At present, the main challenge is to achieve the mass production of high-quality nanofibers and their actual application in the treatment of heavy metal-containing wastewater. Therefore, more consideration should be focused on the improvement of stability, mechanical strength and reusability of ENFMs. This review may provide an insight for the development of ENFMs-based adsorbents for heavy metals separation and water purification in the future.

Properties and Degradation of Novel Fully Biodegradable PLA/PHB Blends Filled with Keratin

The utilization of keratin waste in new materials formulations can prevent its environmental disposal problem. Here, novel composites based on biodegradable blends consisting of poly(lactic acid) (PLA) and poly(3-hydroxybutyrate) (PHB), and filled with hydrolyzed keratin with loading from 1 to 20 wt % were prepared and their properties were investigated. Mechanical and viscoelastic properties were characterized by tensile test, dynamic mechanical thermal analysis (DMTA) and rheology measurements. The addition of acetyltributyl citrate (ATBC) significantly affected the mechanical properties of the materials. It was found that the filled PLA/PHB/ATBC composite at the highest keratin loading exhibited similar shear moduli compared to the un-plasticized blend as a result of the much stronger interactions between the keratin and polymer matrix compared to composites with lower keratin content. The differences in dynamic moduli for PLA/PHB/ATBC blend filled with keratin depended extensively on the keratin content while loss the factor values progressively decreased with keratin loading. Softening interactions between the keratin and polymer matrix resulted in lower glass transitions temperature and reduced polymer chain mobility. The addition of keratin did not affect the extent of degradation of the PLA/PHB blend during melt blending. Fast hydrolysis at 60 °C was observed for composites with all keratin loadings. The developed keratin-based composites possess properties comparable to commonly used thermoplastics applicable for example as packaging materials.

Functionalized electrospun nanofiber membranes for water treatment: A review

Electrospun nanofiber membranes (ENMs) have high porosity, high specific surface area and unique interconnected structure. It has huge advantages and potential in the treatment and recycling of wastewater. In addition, ENMs can be easily functionalized by combining multifunctional materials to achieve different water treatment effects. Based on this, this review summarizes the preparation of functionalized ENMs and its detailed application in the field of water treatment. First, the process and influence factors of electrospinning process are introduced. ENMs with high porosity, thin and small fiber diameter have better performance. Secondly, the modification methods of ENMs are analyzed. Pre-electrospinning and post-electrospinning modification technology can prepare specific functionalized ENMs. Subsequently, functionalized ENMs show water treatment capabilities such as separation, adsorption, photocatalysis, and antimicrobial. Subsequently, the application of functionalized ENMs in water treatment capabilities such as separation, adsorption, photocatalysis, and antimicrobial capabilities were listed. Finally, we also made some predictions about the future development direction of ENMs in water treatment, and hope this article can provide some clues and guidance for the research of ENMs in water treatment.

From fabric to tissue: Recovered wool keratin/polyvinylpyrrolidone biocomposite fibers as artificial scaffold platform

Keratin extracted from wool fibers has recently gained attention as an abundant source of renewable, biocompatible material for tissue engineering and drug delivery applications. However, keratin extraction and processing generally require a copious use of chemicals, not only bearing consequences for the environment but also possibly compromising the envisioned biological outcome. In this study, we present, for the first time, keratin-PVP biocomposite fibers obtained via an all-water co-electrospinning process and explored their properties modulation as a result of different thermal crosslinking treatments. The protein-based fibers featured homogenous morphologies and average diameters in the range of 170-290 nm. The thermomechanical stability and response to a wet environment can be tuned by acting on the curing time; this can be achieved without affecting the 3D fibrous network nor the intrinsic hydrophilic behavior of the material. More interestingly, our protein-based membranes treated at 170 °C for 18 h successfully sustained the attachment and growth of primary human dermal fibroblasts, a cellular model which can recapitulate more faithfully the physiological human tissue conditions. Our proposed approach can be viewed as pivotal in designing tunable protein-based scaffolds for the next generation of skin tissue growth devices.

Use of Chemically Treated Human Hair Wastes for the Removal of Heavy Metal Ions from Water

Human hair is considered a ubiquitous waste product and its accumulation can cause environmental problems. Hence, the search for alternatives that take advantage of this waste as a new raw material is of interest, and contributes to the idea of the circular economy. In this study, chemically modified human hair was used as a low cost biosorbent for the removal of heavy metal ions from aqueous solutions. The effect of the contact time, the pH, and the biosorbent concentration on the biosorption process were investigated. Kinetic modeling indicated that the pseudo-second order kinetic equation fitted well with R2 > 0.999. Furthermore, the equilibrium data fitted the Langmuir adsorption isotherm at 295 K resulting in saturation concentrations of 9.47 × 10−5, 5.57 × 10−5, 3.77 × 10−5, and 3.61 × 10−5 mol/g for the sorption of Cr(III), Cu(II), Cd(II), and Pb(II), respectively. The biosorption process did not change the chemical structure and morphology of the hair, which was shown by FTIR and SEM. In addition, desorption experiments prove that 0.1 mol/L EDTA solution is an efficient eluent for the recovery of Pb(II) from the treated human hair. To summarize, treated human hair showed satisfactory biosorption capacity and can be considered as an effective biosorbent for the treatment of water with a low concentration of heavy metal ions.

N-Doped Animal Keratin Waste Porous Biochar derived from Trapa Natans Husks

Animal-keratin-wastes (AKWs), horns (HN), hair (HR), puffed waterfowl feathers (PF), hydrolyzed waterfowl feathers (HF), hydrolyzed fish meal (HM), crab meat (CM), feathers (FR), shrimp chaff (SC), fish scales (FS), and waste leather (WL) were used as modifiers to prepare animal-keratin-wastes biochars (AKWs-BC) derived from Trapa natans husks (TH). AKWs-BC have a well-developed microporous structure with a pore size mainly below 3 nm. Due to the doping of AKWs, the surface chemical properties of AKWs-BC (especially N functional groups) were improved. The utilization of APWs not only realizes the resource utilization of waste, but also can be used to prepare high-performance biochars.

Electrospun Silver Nanoparticles-Embedded Feather Keratin/Poly(vinyl alcohol)/Poly(ethylene oxide) Antibacterial Composite Nanofibers

Feathers, which contain >90% keratin, are valuable natural protein resources. The aim of this study is to prepare antimicrobial feather keratin (FK)-based nanofibers by incorporating silver nanoparticles (AgNPs). A series of AgNPs-embedded feather keratin/poly(vinyl alcohol)/poly(ethylene oxide) (FK/PVA/PEO) composite nanofibers with varying amounts of AgNPs content were fabricated by electrospinning. Their morphology, crystallinity, thermal stability, tensile property, and antibacterial activity were systematically investigated. The average diameters of composite nanofibers gradually decreased with increases in the amount of AgNPs. The crystallinity, thermal stability, and antibacterial activity of FK/PVA/PEO nanofibers were enhanced by embedding AgNPs. When embedded with 1.2% AgNPs, both the tensile strength and elongation-at-break reached the highest level. This work has the potential to expand the application of FK-based nanofibers in the biomaterial field.

Keratin Associations with Synthetic, Biosynthetic and Natural Polymers: An Extensive Review

Among the biopolymers from animal sources, keratin is one the most abundant, with a major contribution from side stream products from cattle, ovine and poultry industry, offering many opportunities to produce cost-effective and sustainable advanced materials. Although many reviews have discussed the application of keratin in polymer-based biomaterials, little attention has been paid to its potential in association with other polymer matrices. Thus, herein, we present an extensive literature review summarizing keratin's compatibility with other synthetic, biosynthetic and natural polymers, and its effect on the materials' final properties in a myriad of applications. First, we revise the historical context of keratin use, describe its structure, chemical toolset and methods of extraction, overview and differentiate keratins obtained from different sources, highlight the main areas where keratin associations have been applied, and describe the possibilities offered by its chemical toolset. Finally, we contextualize keratin's potential for addressing current issues in materials sciences, focusing on the effect of keratin when associated to other polymers' matrices from biomedical to engineering applications, and beyond.

Influence of Selective Conditions on Various Composite Sorbents for Enhanced Removal of Copper (II) Ions from Aqueous Environments

Numerous pollutants, including dyes, heavy metals, pesticides, and microorganisms, are found in wastewater and have great consequences when discharged onto natural freshwater sources. Heavy metals are predominantly reported in wastewater. Heavy metals are persistent, non-biodegradable and toxic, transforming from a less toxic form to more toxic forms in environmental media under favourable conditions. Among heavy metals, copper is dominantly found in wastewater effluent. In this review, the effects of high concentration of copper in plants and living tissues of both aquatic animals and humans are identified. The performance of different polymer adsorbents and the established optimum conditions to assess the resultant remediation effect as well as the amount of copper removed are presented. This procedure allows the establishment of a valid conclusion of reduced time and improved Cu (II) ion removal in association with recent nano-polymer adsorbents. Nano-polymer composites are therefore seen as good candidates for remediation of Cu ions while pH range 5-6 and room temperature were mostly reported for optimum performance. The optimum conditions reported can be applied for other metal remediation and development of potent novel adsorbents and process conditions.

Preparation of Ag Doped Keratin/PA6 Nanofiber Membrane with Enhanced Air Filtration and Antimicrobial Properties

Coarse wool is a kind of goat wool that is difficult to further process in the textile industry due to its large diameter, dispersion, better strength, and less bending. Therefore, coarse wool is often discarded as waste or made into low-cost products. In this work, keratin was extracted from coarse wool by a high-efficiency method, and then, an Ag-doped keratin/PA6 composite nanofiber membrane with enhanced filtration and antibacterial performance was prepared using HCOOH as solvent and reductant. HAADF-STEM (high-angle annular dark field-scanning transmission electron microscopy) shows that AgNPs are uniformly distributed in keratin/PA6 (30/70) nanofibers. TGA (Thermogravimetric Analysis) and DSC (Differential Scanning Calorimetry) were employed to investigate the thermal stability of composite membranes with different keratin and AgNP contents. The present keratin as a dopant with polyamide-6 (PA6) was found not only to improve air filtration efficiency but also to enhance water–vapour transmission (WVT). The addition of the Ag nanoparticles (AgNPs) gave a strong antibacterial activity to the composite membrane against Staphylococcus aureus (99.62%) and Escherichia coli (99.10%). Bacterial filtration efficiency (BFE) of the composite membrane against S. aureus and E. coli were up to 96.8% and 95.6%, respectively. All of the results suggested a great potential for coarse wool extraction and application in the air filtration field.

Silver-doped keratin nanofibers preserve a titanium surface from biofilm contamination and favor soft-tissue healing

Peri-implantitis is a severe condition affecting the success of transmucosal dental implants: tissue healing is severely limited by the inflammatory processes that come about to control homeostasis in the surrounding tissues. The main cause of peri-implantitis is bacterial biofilm infection; gingival fibroblasts play a pivotal role in regulating the inflammatory cascades. A new technology aimed at preventing bacterial colonization of titanium (Ti) implants, and enhancing the spread of gingival fibroblasts, is presented. Using electro-spinning, mirror-polished Ti disks were uniformly coated with keratin fibers obtained from discarded wool via sulfitolysis. The keratin-coated surfaces were then doped with silver (Ag) to introduce antibacterial properties, using different concentrations of silver nitrate as a precursor (0.01, 0.05 and 0.1 M). The resulting specimens were characterized in terms of morphology and chemical composition by FESEM, FTIR and XPS, revealing silver concentrations between 1.7 and 1.9%. Silver release into the medium was evaluated in the presence of cells (α-MEM) or bacteria (LB) by ICP; release was 0.2-1.4 mg l^-1 for α-MEM, and 10-40 mg l^-1 for LB. The antibacterial properties of the Ag-doped specimens were tested against a multidrug-resistant Staphylococcus aureus biofilm through morphology (FESEM) and metabolic assay (XTT); reduction in viability was significant (p < 0.05; >80% reduction within 72 h). Lastly, the cytocompatibility of the specimens was confirmed using human primary gingival fibroblasts, whose viability, spread and matrix deposition were found to be comparable to those of untreated Ti polished controls (p > 0.05). Thus, Ag surface enrichment was effective in reducing viability and maturation of S. aureus biofilm, without compromising human cell viability. Moreover, cell spread was found to be very sensitive to keratin fiber stimulation. The strategy thus appears to be very promising to introduce surface features in line with the main requirements for transmucosal dental implants.

Electrospun poly(acrylic acid)/poly(vinyl alcohol) nanofibrous adsorbents for Cu(ii) removal from industrial plating wastewater

Nanofibrous adsorbents were fabricated by electrospinning with a blend solution of poly(acrylic acid) (PAA) and poly(vinyl alcohol) (PVA) polymers and used for copper (Cu(ii)) removal from industrial plating wastewater.

Fabrication and characterization of electrospun feather keratin/poly(vinyl alcohol) composite nanofibers

We have fabricated random and aligned feather keratin (FK)/PVA composite nanofibers through an electrospinning process. The morphology, molecular interactions, crystallization behavior, and tensile properties of the nanofibers were investigated.

Preparation of Petaloid TPEE@AlOOH Nanofibers with Cr (VI)-Removal Capacity

Hexavalent chromium ( Cr (VI)) is a highly toxic pollutant which is harmful to marine organisms as well as humanity. Removing Cr (VI) from water is a hot-spot in environmental remediation. In this work, a novel kind of composite nanofibers membrane (thermal plastic elastomer ester (TPEE)@ AlOOH ) was first proposed by a simple method, based on a hybrid strategy composed of electrospinning and hydrothermal method. The obtained nanofibrous membrane was turned out to be a petaloid structure, which can enlarge the specific surface area of electrospun fibers. Furthermore, the Cr (VI) removal experiments suggested that the obtained nanofibrous membrane showed a high and fast efficiency, a stable recyclable property for the Cr (VI) removal. Therefore, such a novel nanofibrous membrane can be potentially widely used in Cr (VI) removal.

Keratin–polyethylene oxide bio-nanocomposites reinforced with ultrasonically functionalized graphene

Polyethylene oxide (PEO) functionalized graphene (f-G) was prepared by ultrasonication of pristine graphene in PEO aqueous solution.