Poly(l-lactic acid)-polyethylene glycol-poly(l-lactic acid) triblock copolymer: A novel macromolecular plasticizer to enhance the crystallization of poly(l-lactic acid)

Improvement in Crystallization, Thermal, and Mechanical Properties of Flexible Poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide) Bioplastic with Zinc Phenylphosphate

Poly(L-lactide)-b-poly(ethylene glycol)-b-poly(L-lactide) (PLLA-PEG-PLLA) shows promise for use in bioplastic applications due to its greater flexibility over PLLA. However, further research is needed to improve PLLA-PEG-PLLA's properties with appropriate fillers. This study employed zinc phenylphosphate (PPZn) as a multi-functional filler for PLLA-PEG-PLLA. The effects of PPZn addition on PLLA-PEG-PLLA characteristics, such as crystallization and thermal and mechanical properties, were investigated. There was good phase compatibility between the PPZn and PLLA-PEG-PLLA. The addition of PPZn improved PLLA-PEG-PLLA's crystallization properties, as evidenced by the disappearance of the cold crystallization temperature, an increase in the crystallinity, an increase in the crystallization temperature, and a decrease in the crystallization half-time. The PLLA-PEG-PLLA's thermal stability and heat resistance were enhanced by the addition of PPZn. The PPZn addition also enhanced the mechanical properties of the PLLA-PEG-PLLA, as demonstrated by the rise in ultimate tensile stress and Young's modulus. We can conclude that the PPZn has potential for use as a multi-functional filler for the PLLA-PEG-PLLA composite due to its nucleating-enhancing, thermal-stabilizing, and reinforcing ability.

Enhancement in Crystallizability of Poly(L-Lactide) Using Stereocomplex-Polylactide Powder as a Nucleating Agent

High-molecular-weight poly(L-lactide) (HMW-PLLA) is a promising candidate for use as a bioplastic because of its biodegradability and compostability. However, the applications of HMW-PLLA have been limited due to its poor crystallizability. In this work, stereocomplex polylactide (scPLA) powder was prepared by precipitation of a low-molecular-weight poly(L-lactide)/poly(D-lactide) (LMW-PLLA/LMW-PDLA) blend solution and investigated for use as a fully-biodegradable nucleating agent for HMW-PLLA compared to LMW-PLLA powder. The obtained LMW-PLLA and scPLA powders with a nearly spherical shape showed complete homo- and stereocomplex crystallites, respectively. HMW-PLLA/LMW-PLLA powder and HMW-PLLA/scPLA powder blends were prepared by melt blending. The LMW-PLLA powder was homogeneously melted in the HMW-PLLA matrices, whereas the scPLA powder had good phase compatibility and was well-dispersed in the HMW-PLLA matrices, as detected by scanning electron microscopy (SEM). It was shown that the enthalpies of crystallization (ΔHc) upon cooling scans for HMW-PLLA largely increased and the half crystallization time (t1/2) dramatically decreased as the scPLA powder content increased; however, the LMW-PLLA powder did not exhibit the same behavior, as determined by differential scanning calorimetry (DSC). The crystallinity content of the HMW-PLLA/scPLA powder blends significantly increased as the scPLA powder content increased, as determined by DSC and X-ray diffractometry (XRD). In conclusion, the fully biodegradable scPLA powder showed good potential for use as an effective nucleating agent to improve the crystallization properties of the HMW-PLLA bioplastic.

Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer

In this work, the synthesized PLLA/PCL multi-block copolymers with different compositions were introduced into a stereocomplexed poly(lactide) (sc-PLA) matrix to accelerate the stereocomplexation of PLA enantiomers and improve its inherent brittleness. The PLLA/PCL multi-block copolymers were in different compositions to adjust the molecular weight of the PLLA block. The structure, molecular weight, crystallization behavior, crystal structure and thermal stability of PLLA/PCL multi-block copolymers were investigated. The results indicated that PLLA/PCL multi-block copolymers with controllable structure and composition were successfully synthesized. On this basis, the blends of sc-PLA and PLLA/PCL multi-block copolymers were prepared by solution casting, and characterized. The results revealed that the introduction of PLLA/PCL multi-block copolymers promoted the stereocomplexation of the PLA enantiomers during the melting crystallization process to obtain a complete stereocomplexed material. But the presence of the PCL block leads to a decrease in the melting temperature of the stereocomplex and difficulty in homogeneous nucleation. Compared with sc-PLA, the elongation at break of the blends was significantly improved and their tensile strengths were only slightly reduced. And the thermal stability and mechanical properties of the blends could be adjusted by controlling the content and composition of PCL/PLLA multi-block copolymers. These results revealed that the degree of stereocomplexation and toughness of sc-PLA were improved, which may expand the application fields of PLA-based materials.

The PLLA/PCL multi-block copolymer was introduced into the stereocomplexed PLA matrix, and its effect on the crystallization, thermal and mechanical properties of the stereocomplexed PLA was discussed.

Synergistic effects of PEG middle-blocks and talcum on crystallizability and thermomechanical properties of flexible PLLA-b-PEG-b-PLLA bioplastic

In this study, talcum was melt-blended with a flexible poly(l-lactide)-b-polyethylene glycol-b-poly(l-lactide) triblock copolymer (PLLA-PEG-PLLA) with 1, 2, 4, and 8 wt% talcum, for improvement of the crystallization and thermomechanical properties of PLLA-PEG-PLLA compared with PLLA. The crystallizability of PLLA-PEG-PLLA/talcum composites was better than that of PLLA/talcum composites as determined from differential scanning calorimetry. X-ray diffractometry showed that the PLLA-PEG-PLLA/talcum films had a higher degree of crystallinity than the PLLA/talcum films. PEG middle-blocks and talcum showed a synergistic effect for crystallization of PLLA end-blocks. The PLLA-PEG-PLLA/talcum films showed better thermomechanical properties than those of the PLLA/talcum films as determined from dynamic mechanical analysis. This was confirmed from the results of dimensional stability to heat. In summary, the PLLA-PEG-PLLA/talcum composites have potential for use as flexible bioplastics with good dimensional stability to heat.

The isothermal crystallization kinetic of poly(L-lactide)-block-poly(ethylene glycol) block copolymers (PLLA-PEG): Effect of block lengths of PEG and PLLA

Poly(ethylene glycol)-block-poly(L-lactide) (PEG-PLLA) is a biodegradable copolymer which widely applied to medicine and drug system, and the morphology, organization and mechanical properties were extensively investigated. However, the crystallization kinetic were...

Synthesis of flexible poly(l-lactide)-b-polyethylene glycol-b-poly(l-lactide) bioplastics by ring-opening polymerization in the presence of chain extender

Poly(l-lactide)-b-polyethylene glycol-b-poly(l-lactide) (PLLA-PEG-PLLA) is found to be more flexible than PLLA due to the flexibility of PEG middle blocks. Melt flow and mechanical properties of PLLA-PEG-PLLA were improved through post melt blending with a chain extender (CE). In this work, in situ chain-extended PLLA-PEG-PLLAs were synthesized by ring-opening polymerization in the presence of Joncryl® CE. The influence of CE content (1.0, 2.0, and 4.0 phr) on the gel content, melt flow index (MFI), thermal properties, and mechanical properties of the obtained in situ chain-extended PLLA-PEG-PLLAs was investigated. The gel content of in situ chain-extended PLLA-PEG-PLLA increased while the MFI and degree of crystallinity significantly decreased with increasing CE content. The in situ chain-extended PLLA-PEG-PLLA with 1.0 phr CE showed the best tensile properties. The extensibility of in situ chain-extended PLLA-PEG-PLLA films decreased when the CE contents were higher than 1.0 phr. These in situ chain-extended PLLA-PEG-PLLA films can be used as highly flexible bioplastics.

Effect of Poly(styrene-ran-methyl acrylate) Inclusion on the Compatibility of Polylactide/Polystyrene-b-Polybutadiene-b-Polystyrene Blends Characterized by Morphological, Thermal, Rheological, and Mechanical Measurements

A poly(styrene-ran-methyl acrylate) (S-MA) (75/25 mol/mol), synthesized by surfactant-free emulsion copolymerization, was used as a compatibilizer for polystyrene-b-polybutadiene-b-polystyrene (SBS)-toughened polylactide (PLA) blends. Upon compatibilization, the blends exhibited a refined dispersed-phase morphology, a decreased crystallinity with an increase in their amorphous interphase, improved thermal stability possibly from the thicker, stronger interfaces insusceptible to thermal energy, a convergence of the maximum decomposition-rate temperatures, enhanced magnitude of complex viscosity, dynamic storage and loss moduli, a reduced ramification degree in the high-frequency terminal region of the Han plot, and an increased semicircle radius in the Cole–Cole plot due to the prolonged chain segmental relaxation times from increases in the thickness and chain entanglement degree of the interphase. When increasing the S-MA content from 0 to 3.0 wt %, the tensile properties of the blends improved considerably until 1.0 wt %, above which they then increased insignificantly, whereas the impact strength was maximized at an optimum S-MA content of ~1.0 wt %, hypothetically due to balanced effects of the medium-size SBS particles on the stabilization of preexisting crazes and the initiation of new crazes in the PLA matrix. These observations confirm that S-MA, a random copolymer first synthesized in our laboratory, acted as an effective compatibilizer for the PLA/SBS blends.

Tailoring Crystalline Morphology by High-Efficiency Nucleating Fiber: Toward High-Performance Poly(l-lactide) Biocomposites

In this work, a high-melting-point poly(l-lactide) fiber (hPLLA fiber) with high-efficiency nucleation activity was prepared and introduced into PLLA matrix to prepare fully biodegradable PLLA biocomposites. The highly active nucleating surfaces of the hPLLA fiber induced chain ordering and lamellar organization, leading to a preferable formation of well-organized PLLA transcrystallinity at the surface of the hPLLA fiber under quiescent conditions. The construction of such compact transcrystallinity increased the crystallinity and enhanced the interfacial adhesion, which largely promoted heat resistance, tensile strength, and barrier property of PLLA biocomposites at a low content of hPLLA fiber. With the addition of 1 wt % hPLLA fiber, the storage modulus of the PLLA biocomposite was enhanced by 82 times from 4 to 330 MPa at 80 °C and the oxygen permeability coefficient and water permeability coefficient were decreased by 52 and 51% to be 5.9 × 10^-15 cm³·cm/cm²·s·Pa and 4.5 × 10^-14 g·cm/cm²·s·Pa, respectively, compared with those of pure PLLA. Moreover, the transparency of PLLA was maintained with the incorporation of hPLLA fiber. Thus, this strategy paved a new way to prepare high-performance and fully biodegradable biocomposites.