Highly efficient adsorbent material for removal of methylene blue dye based on functionalized polyacrylonitrile

Physicochemical, steric, and energetic characterization of kaolinite based silicate nano-sheets as potential adsorbents for safranin basic dye: effect of exfoliation reagent and techniques

Kaolinite was subjected to advanced exfoliation processes to form separated nano-silicate sheets (EXK) with enhanced physicochemical properties as adsorbents. This involved the incorporation of different exfoliating agents, urea (U/EXK), KNO3 (N/EXK), and CTAB (C/EXK), highlighting their impacts on their textural and surficial properties as adsorbents for safranin dye. The applied characterization techniques confirmed the higher exfoliating degree of C/EXK, followed by N/EXK and U/EXK. This appeared significantly in the determined surface area (55.7 m2/g (C/EXK), 36.7 m2/g (U/EXK), and 47.1 m2/g (N/EXK)) and adsorption performances. The C/EXK structure displayed a better safranin uptake capacity (273.2 mg/g) than N/EXK (231 mg/g) and U/EXK (178.4 mg/g). Beside the remarkable differences in textural properties, the advanced mathematical modeling and the corresponding steric and energetic parameters illustrate the mentioned uptake properties. The interface of C/EXK is highly saturated by active uptake sites (Nm = 158.8 mg/g) as compared to N/EXK (109.3 mg/g) and U/EXK (93.4 mg/g), which is in agreement with the characterization findings and the expected higher exposure of siloxane groups. Each of these sites can be filled with four dye molecules using C/EXK and N/EXK, which implies the vertical orientation of these adsorbed ions and the effective operation of multi-molecular mechanisms. The energetic (ΔE < 40 kJ/mol) and thermodynamic investigations indicate the spontaneous, physical, and exothermic uptake of safranin molecules by EXK particulates. These mechanisms might involve dipole bonding (2-29 kJ/mol), electrostatic attraction (2-50 kJ/mol), van der Waals forces (4-10 kJ/mol), and hydrogen bonding (<30 kJ/mol).

Nonsolvent-Induced Phase Separation pPAN Separators for Dendrite-Free Rechargeable Aluminum Batteries

Rechargeable aluminum batteries (RAB) are a promising energy storage system with high safety, long cycle life, and low cost. However, the strong corrosiveness of chloroaluminate ionic liquid electrolytes (ILEs) severely limits the development of RAB separators. Herein, a nonsolvent-induced phase separation strategy was applied to fabricate the pPAN (poly(vinyl alcohol)-modified polyacrylonitrile) separator, which exhibits prominent chemical and electrochemical stability in ILEs. The pPAN separator, owing to its uniform pore size distribution and strong electronegativity with a zeta potential of about -10.20 mV, can effectively inhibit the growth of dendrites. Benefiting from the good ion conductivity (6.38 mS cm-1) and high ion migration number (0.133) of pPAN separator, the full cell with pPAN separator demonstrates stable operation for more than 500 cycles at 600 mA g-1, with a high capacity of 88.8 mAh g-1. When integrating into sodium-ion batteries, the pPAN separators also show an excellent electrochemical performance. This work provides a considerable approach for designing separators to address the issue of Al anode dendrite growth in RABs.

Steric, Synergetic, Energetic Studies on the Impact of the Type of the Hybridized Polymers (Chitosan and β-Cyclodextrin) on the Adsorption Properties of Zeolite-A for Congo Red Dye

Zeolite-A was synthesized successfully from kaolinite and hybridized with two species of biopolymers (chitosan (CH/Z) and β-cyclodextrin (CD/Z)). The obtained hybridized forms were assessed as potential adsorbents of Congo red synthetic dye (CR) with enhanced affinities and elimination capacities. The synthesized CD/Z and CH/Z hybrids demonstrated uptake capacities of 223.6 and 208.7 mg/g, which are significantly higher than single-phase zeolite-A (140.3 mg/g). The integrated polymers change the surface area, surface reactivity, and number of free active receptors that are already present. The classic isotherm investigations validate Langmuir equilibrium behavior for ZA and Freundlich properties for CD/Z and CH/Z. The steric parameters validate a strong increase in the existing active receptors after the incorporation of CD (CD/Z) to be 98.1 mg/g as compared to 83 mg/g for CH/Z and 60.6 mg/g for ZA, which illustrate the detected uptake behaviors. Moreover, the CR dye was adsorbed as several molecules per single site, reflecting the vertical uptake of these molecules by multimolecular mechanisms. The energetic assessment, considering both Gaussian energies and adsorption energies (<40 kJ/mol), validates the dominant impact of the physical mechanism during the sequestration of CR (dipole binding interactions (2-29 kJ/mol) and hydrogen bonds (<30 kJ/mol)), in addition to the considerable effect of ion exchange processes. Based on the thermodynamic parameters, the CR molecules were adsorbed by exothermic and spontaneous reactions.

Insight into roles of carbon anodes for removal of refractory organic contaminants in electro-peroxone system: Mechanism, performance and stability

Electro-peroxone (EP) is a novel technique for the removal of refractory organic contaminants (ROCs), while the role of anode in this system is neglected. In this work, the EP system with graphite felt anode (EP-GF) and activated carbon fiber anode (EP-ACF) was developed to enhance ibuprofen (IBP) removal. The results showed that 91.2% and 98.6% of IBP was removed within 20 min in EP-GF and EP-ACF, respectively. Hydroxy radical (O⋅H) was identified as the dominant reactive species, contributing 80.9% and 54.0% of IBP removal in EP-ACF and EP-GF systems, respectively. The roles of adsorption in EP-ACF and direct electron transfer in EP-GF cannot be ignored. Due to the differences in mechanism, EP-GF and EP-ACF systems were suitable for the removal of O⋅H-resistant ROCs (e.g., oxalic acid and pyruvic acid) and non-O⋅H-resistant ROCs (e.g., IBP and nitrobenzene), respectively. Both systems had excellent stability relying on the introduction of oxygen functional groups on the anode, and their electrolysis energy consumption was significantly lower than that of EP-Pt system. The three degradation pathways of IBP were proposed, and the toxicity of intermediates were evaluated. In general, carbon anodes have a good application prospect in the removal of ROCs in EP systems.

Tailored ultra-tough, antimicrobial and recyclable hydrogels based on chitosan and ionic liquid modified montmorillonite with different chain lengths for efficient adsorption of organic dyes in wastewater

Water pollution had exacerbated the global water crisis. Dye effluents posed a serious threat to the environment and human health, so there was an urgent need to develop sustainable methods to mitigate water pollution. In this work, sodium-based montmorillonite (MMT) was stripped using ionic liquids (ILs) with different chain lengths, and a pAAM/pAA/LMA/MMT@ILs-CS hydrogel adsorbent (MICHA) was prepared. The gel-based adsorbent was used to adsorb typical cationic (methylene blue: MB, rhodamine B: RhB) and anionic (methyl orange: MO, indigo carmine: IC) dyes from wastewater. The maximum adsorption capacities of MI16CHA for MB, MO, IC and RhB were 349.6817, 325.415, 316.0142 and 339.8154 mg/g, respectively. The adsorption kinetics and equilibrium data of MI16CHA for dyes were in accordance with the pseudo-first order and Langmuir isotherm models. The adsorption mechanism of MI16CHA on dyes were based on hydrogen bonding, electrostatic and π-π interaction. Thermodynamic studies showed that the adsorption of dyes on MI16CHA was spontaneous and heat-absorbing. The selective experiments demonstrated that MI16CHA has a promising application in real industrial conditions. Cyclic adsorption tests demonstrated the excellent recyclability of MI16CHA. In addition, MI16CHA had excellent antimicrobial and mechanical properties, which endowed the gel adsorbent with anti-pollution and durability.

Hemicelluloses hydrogel: Synthesis, characterization, and application in dye removal

Novel materials using biowaste as adsorbents in wastewater treatment have been allocated considerable interest. Herein, we present the synthesis of different hydrogels of crosslinked polyacrylamide in presence of hemicelluloses with/ without bentonite, using a soft reaction condition. The structure of new hydrogels was characterized by spectroscopic, thermal and microscopic experiments. The semi-interpenetrated network with hemicelluloses: 10 %; acrylamide 79 %; bentonite 10 %; N,N,N',N'-tetramethylethylenediamine: 1 % allows reducing 20 % the use of non-renewable acrylamide, without changing its decomposition temperatures and keeping its water absorption capacity. This hydrogel was applied to dye removals, such as rhodamine B, methylene red and methylene blue in aqueous solutions. In the case of methylene blue, highest removal is observed with maximum adsorption of qmax = 140.66 mg/g, compared to material without hemicelluloses that only a qmax = 88.495 mg/g. The adsorption kinetics and equilibrium adsorption isotherms are in accordance with the pseudo-second-order kinetic model and Langmuir isotherm model, respectively. The developed hydrogel from hemicelluloses represents a potential alternative adsorbent for a sustainable system of sewage treatment.

Development of Novel PET-PAN Electrospun Nanocomposite Membrane Embedded with Layered Double Hydroxides Hybrid for Efficient Wastewater Treatment

Layered double hydroxides (LDHs) with their unique structural chemistry create opportunities to be modified with polymers, making different nanocomposites. In the current research, a novel PET-PAN embedded with Mg-AI-LDH-PVA nanocomposite membrane was fabricated through electrospinning. SEM, EDX, FTIR, XRD, and AFM were carried out to investigate the structure and morphology of the nanocomposite membrane. The characterization of the optimized nanocomposite membrane showed a beadless, smooth structure with a nanofiber diameter of 695 nm. The water contact angle and tensile strength were 16° and 1.4 Mpa, respectively, showing an increase in the hydrophilicity and stability of the nanocomposite membrane by the addition of Mg-Al-LDH-PVA. To evaluate the adsorption performance of the nanocomposite membrane, operating parameters were achieved for Cr(VI) and methyl orange at pH 2.0 and pH 4.0, respectively, including contact time, adsorbate dose, and pollutant concentration. The adsorption data of the nanocomposite membrane showed the removal of 68% and 80% for Cr(VI) and methyl orange, respectively. The process of adsorption followed a Langmuir isotherm model that fit well and pseudo-2nd order kinetics with R2 values of 0.97 and 0.99, respectively. The recycling results showed the membrane's stability for up to five cycles. The developed membrane can be used for efficient removal of pollutants from wastewater.

Steric and Energetic Studies on the Synergetic Enhancement Effect of Integrated Polyaniline on the Adsorption Properties of Toxic Basic and Acidic Dyes by Polyaniline/Zeolite-A Composite

The synergetic enhancement effect of the polyaniline (PANI) integration process on the adsorption properties of the PANI/zeolite-A composite (PANI/ZA) as an adsorbent for malachite green and Congo red synthetic dyes was evaluated based on classic equilibrium modelling in addition to the steric and energetic parameters of advanced isotherm studies. The PANI/ZA composite displays enhanced adsorption capacities for both methylene blue (270.9 mg/g) and Congo red (235.5 mg/g) as compared to ZA particles (methylene blue (179.6 mg/g) and Congo red (140.3 mg/g)). The reported enhancement was illustrated based on the steric parameters of active site density (Nm) and the number of adsorbed dyes per active site (n). The integration of PANI strongly induced the quantities of the existing active sites that have enhanced affinities towards both methylene blue (109.2 mg/g) and Congo red (92.9 mg/g) as compared to the present sites on the surface of ZA. Every site on the surface of PANI/ZA can adsorb about four methylene blue molecules and five Congo red molecules, signifying the vertical orientation of their adsorbed ions and their uptake by multi-molecular mechanisms. The energetic investigation of the methylene blue (-10.26 to -16.8 kJ/mol) and Congo red (-9.38 to -16.49 kJ/mol) adsorption reactions by PANI/ZA suggested the operation of physical mechanisms during their uptake by PANI/ZA. These mechanisms might involve van der Waals forces, dipole bonding forces, and hydrogen bonding (<30 kJ/mol). The evaluated thermodynamic functions, including enthalpy, internal energy, and entropy, validate the exothermic and spontaneous behaviours of the methylene blue and Congo red uptake processes by PANI/ZA.

In situ preparation of TiO2/f-MWCNT catalyst using Pluronic F127 assisted sol-gel process for sonocatalytic degradation of methylene blue

In this study, titanium dioxide- Pluronics @F127/functionalized -multi walled carbon nanotubes (TiO₂-F127f-/MWCNT) nanocatalysts were prepared, characterized, and used in methylene blue (MB) degradation under ultrasonic conditions. The characterization studies were performed using TEM, SEM, and XRD analyses to reveal the morphological and chemical properties of TiO₂-F127/MWCNT nanocatalysts. To detect the optimum parameters for MB degradation using TiO₂-F127/f-MWCNT nanocatalysts, several experimental parameters were conducted at various conditions such as different temperatures, pH, catalyst amount, hydrogen peroxide (H₂O₂) concentration, and various reaction contents. Transmission electron microscopy (TEM) analyses showed that TiO₂-F127/f-MWCNT nanocatalysts consisted of a homogenous structure and have a 12.23 nm particle size. The crystalline particle size of TiO₂-F127/MWCNT nanocatalysts was found to be 13.31 nm. Scanning electron microscope (SEM) analyses revealed the surface structure of TiO₂-F127/f-MWCNT nanocatalysts turned to be modified after TiO₂ loaded on MWCNT. Under the optimum conditions; pH: 4, MB concentration: 25 mg/L, H₂O₂ concentration: 30 mol/L, reaction time: and catalyst dose: 24 mg/L, chemical oxygen demand (COD) removal efficiency reached a maximum of 92%. To detect the radical effectiveness, three scavenger solvents were tested. Reuse experiments revealed that TiO₂-F127/f-MWCNT nanocatalysts retained 84.2% catalytical activity after 5 cycles. Gas chromatography-mass spectrometry (GC-MS) was successfully used to identify the generated intermediates. In addition, the GC-MS was successfully used to identify produced intermediates. Based on the experimental results, it has been suggested that •OH radicals are the main active species responsible for the degradation reaction in the presence of the TiO₂-F127/f-MWCNT nanocatalysts.

Fabrication of different adsorbents based on zirconium oxide, graphene oxide, and dextrin for removal of green malachite dye from aqueous solutions

In this study, graphene oxide and amine graphene were studied by binding to dextrin and zirconium oxide nanoparticles as adsorbent nanocomposites to the removal of dye. Identification and characterization of the synthesized materials were examined using FTIR, XRD, SEM, and BET analyses. Adsorption tests between adsorbents and green malachite (MG) dye solution for the synthesized nanocomposites were performed by considering parameters such as contact time, solution pH, and adsorbent dosage. The data indicated that dye removal increased with increasing the amount of adsorbent dosage. Increased dye removal by increasing the adsorbent dosage can be attributed to the increase of availability of the number of active sites. The active adsorption sites are saturated during the adsorption process, by the molecules of the adsorbate and filled over time. The results showed that the synthesized bio-composite had malachite green removal ability from aqueous media.

Synthesis of Metalorganic Copolymers Containing Various Contorted Units and Iron(II) Clathrochelates with Lateral Butyl Chains: Conspicuous Adsorbents of Lithium Ions and Methylene Blue

We report the synthesis of three highly soluble metalorganic copolymers, TCP1-3, that were made from a one-pot complexation of iron(II) clathrochelate units that are interconnected by various thioether-containing contorted groups. TCP1-3 were converted into their poly(vinyl sulfone) derivatives OTCP1-3 quantitatively via the selective oxidation of the thioether moieties into their respective sulfones. All of the copolymers, TCP1-3 and OTCP1-3, underwent structural analysis by various techniques; namely, ¹H- and ¹³C-nuclear magnetic resonance (NMR), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), and gel permeation chromatography (GPC). The copolymers were tested as potent lithium ions adsorbents revealing a maximum adsorption (q_m) value of 2.31 mg g^-1 for OTCP2. Furthermore, this same copolymer was found to be a promising adsorbent of methylene blue (MEB); an isothermal adsorption study divulged that OTCP2's uptake of MEB from an aqueous solution (following the Langmuir model) was, at maximum adsorption capacity, (q_m) of 480.77 mg g^-1; whereas the kinetic study divulged that the adsorption follows pseudo second-order kinetics with an equilibrium adsorption capacity (q_e,cal) of 45.40 mg g^-1.

The Removal of a Textile Dye from an Aqueous Solution Using a Biocomposite Adsorbent

The adsorption mechanisms of methylene blue (MB) onto olive waste (residue) treated with KOH (OR-KOH) and onto an OR-KOH and PEG-silica gel composite (OR-KOH/PEG-SG) at various temperatures were investigated using a combination of experimental analysis and Monte Carlo ab-initio simulations. The effects of adsorption process variables such as pH, temperature, and starting adsorbate concentration were investigated. The experimental data were fitted to Langmuir and Freundlich models. The maximum adsorption capacities of MB onto OR-KOH and OR-KOH/PEG-SG adsorbents reached values of 504.9 mg/g and 161.44 mg/g, respectively. The experimental FT-IR spectra indicated that electrostatic attraction and hydrogen bond formation were critical for MB adsorption onto the adsorbents generated from olive waste. The energetic analyses performed using Monte Carlo atomistic simulations explained the experimental results of a differential affinity for the investigated adsorbents and confirmed the nature of the interactions between methylene blue and the adsorbents to be van der Waals electrostatic forces.