Thermodynamic criteria analysis for the use of taro starch spherical aggregates as microencapsulant matrix

Kinetics of low radioactive wastewater imbibition and radionuclides sorption in partially saturated ternary-binder mortar

This study seeks to assess the imbibition kinetics of low radioactive wastewater (from the DayaBay nuclear power plant) into a partially saturated ternary-binder mortar, as well as the sorption kinetics of ⁶⁰Co and ¹³⁷Cs from the water. Mortar samples with the initial saturation degrees of 0, 0.4, 0.6, 0.8 and 1.0 were prepared for the wastewater treatment. Pore structure of the mortar was characterized using water vapor sorption isotherm and mercury intrusion porosimetry tests interpreted by the Guggenheim-Anderson-de Boer isothermal equilibrium, and volume- and energy-based fractal models. Results show that the mortar has consistent fractal pore structure between the models, and the liquid imbibitions follow the fractal imbibition kinetics, in which the parameters are non-linearly impacted by the initial saturation degrees. The sorption rate and retention capacity of ¹³⁷Cs are much lower than those of ⁶⁰Co, and both follow the Brouers-Sotolongo fractional kinetics. The findings uncover the complex liquid imbibition and radionuclides sorption kinetics in cement-based porous materials, and the in-situ data would contribute to the material designs and sorption controls for large scale in-situ treatments of wastewater from nuclear power plant.

Rheological Analysis of the Structuralisation Kinetics of Starch Gels

Using the method of dynamic–mechanical analysis, the structuralisation kinetics of condensed starch solutions, cooled down to the temperature of 20 °C, was investigated. A close correlation of spatial crosslinking with local processes of macromolecule associations was discovered. It was found that depending on the concentration intervals of starch solutions, equilibrium nodes of the spatial network assume the form of either single or double hexagonal structures made up of bispiral chain associates. The increase of gel crosslinking, together with the passage of time, is the result of increasing the node functionality of the spatial network.

Starch-based materials encapsulating food ingredients: Recent advances in fabrication methods and applications

Encapsulation systems have gained significant interest in designing innovative foods, as they allow for the protection and delivery of food ingredients that have health benefits but are unstable during processing, storage and in the upper gastrointestinal tract. Starch is widely available, cheap, biodegradable, edible, and easy to be modified, thus highly suitable for the development of encapsulants. Much efforts have been made to fabricate various types of porous starch and starch particles using different techniques (e.g. enzymatic hydrolysis, aggregation, emulsification, electrohydrodynamic process, supercritical fluid process, and post-processing drying). Such starch-based systems can load, protect, and deliver various food ingredients (e.g. fatty acids, phenolic compounds, carotenoids, flavors, essential oils, irons, vitamins, probiotics, bacteriocins, co-enzymes, and caffeine), exhibiting great potentials in developing foods with tailored flavor, nutrition, sensory properties, and shelf-life. This review surveys recent advances in different aspects of starch-based encapsulation systems including their forms, manufacturing techniques, and applications in foods.

Difference Analysis of Gas Molecules Diffusion Behavior in Natural Ester and Mineral Oil Based on Molecular Dynamic Simulation

Natural ester, as a new environmentally green insulating oil, has been widely used in transformer. In an oil-immersed transformer, the normal aging, thermal failure, and discharge failure could easily lead to the decomposition of the oil-paper insulation system and produce different kinds of gases. Studying gas dissolution in natural ester and mineral oil could provide assistance in applying criteria to make a diagnosis of different kinds of faults in the transformer. In this paper, the molecular dynamics method was used to investigate the diffusion behavior of seven fault characteristic gases (including H₂, CO, CH₄, C₂H₂, CO₂, C₂H₄, C₂H₆) in natural ester and mineral oil. The simulation parameters of free volume, interaction energy, mean square displacement, and diffusion coefficient were compared between the natural ester and mineral oil. Meanwhile, the influence of temperature on the diffusion of gas molecules in two kinds of oils was also analyzed. Results showed that the free volume, the interaction energy, and the relative molecular mass of gas molecules were the factors influenced by the diffusion of gas molecules in natural ester and mineral oil. The order of the diffusion coefficients of gas molecules in natural ester was as follows: H₂ > CH₄ > CO > C₂H₂ > C₂H₄ > CO₂ > C₂H₆ and that in mineral oil was as follows: H₂ > CH₄ > CO> C₂H₂ > C₂ H₄ > C₂H₆ > CO₂. By comparing the diffusion behavior of gas molecules in natural ester and mineral oil, it was found that the smaller free volume and higher interaction energy of gas molecules in natural ester were the major reasons for the gas molecules to be more difficult to diffuse in natural ester. The rising temperature could enhance the free volume and reduce the interaction energy between gas molecules and oil. The diffusion coefficient of gas molecules increased exponentially with the follow of temperature. However, the temperature didn’t affect the ordering of diffusion coefficient, free volume, and interaction energy of gas molecules in natural ester and mineral oil.

Preparation and Self-Repairing Properties of Urea Formaldehyde-Coated Epoxy Resin Microcapsules

Urea formaldehyde resin-coated epoxy resin microcapsules were prepared by two-step in situ polymerization. The effects of five factors on the yield, coverage rate, repair rate, and morphology of the microcapsules were investigated by five factors and four levels of orthogonal test. These five factors were the mass ratio of the core to the wall material (Wcore:Wwall), the mass ratio of the emulsifier to the core material (Wemulsifier:Wcore), stirring rate, deposition time, and mass ratio of the emulsifier solution to the core material (Wemulsifier solution:Wcore). The ideal technological level of microcapsule synthesis was determined. According to the results of the range and variance of yield, coverage rate, and repair rate, the comprehensive properties of microcapsules became ideal. At this time, the Wcore:Wwall was 0.8 : 1, Wemulsifier:Wcore was 1 : 100, stirring rate was 600 r/min, deposition time was 32 h, and Wemulsifier solution:Wcore was 8 : 1. When the concentration of microcapsules in the epoxy resin was 10.0%, the self-repair rate was the best and the repair rate was 114.77%. This study is expected to provide a reference value for the preparation of a microcapsule self-healing technology and lay a foundation for the subsequent development of self-healing materials.