An alternative geometry for bolometer sensors for use at high operating temperatures

Calibration and thermal test results of prototype bolometer sensors for ITER fusion reactor

For over 10 years, several bolometer sensors with different properties have been tested in the IBOVAC facility. The aim has been to develop a bolometer sensor that can be operated in ITER and can withstand harsh operating conditions. For this purpose, important physical properties of the sensors, i.e., cooling time constant τ, normalized heat capacity κ, and normalized sensitivity s_n, have been characterized in a vacuum condition and at various temperatures up to 300 °C. The calibration is achieved by ohmic heating of the sensor absorbers by applying a DC voltage and recording exponential current fall during heating. Recently, a Python program was developed to analyze the data and extract the above mentioned parameters including the uncertainties from recorded currents. In the present series of experiments, the latest prototype sensors developed for ITER are tested and evaluated. These include three different sensor types: two with Au absorbers on ZrO₂ membranes (self-supporting substrate sensors) and one with Au absorbers on Si₃N₄ membranes supported by a Si frame (supported membrane sensors). Tests revealed that the sensor with ZrO₂ substrate can only be operated up to 150 °C, while the supported membrane sensors passed the tests up to 300 °C successfully. These results will be used, together with other upcoming tests, such as irradiation testing, to select the most suitable sensors to be employed in ITER.

Consideration of signal to noise ratio for an imaging bolometer for ITER

An infrared imaging video bolometer (IRVB) is proposed for ITER having a tangential view of the entire ITER cross section. For the initial estimate of the signal level, a 840 m³ plasma is assumed to uniformly radiate 67.3 MW. A more detailed estimate of the signal strength is provided by synthetic images based on radiation data from SOLPS and SANCO models for the edge and core plasma, respectively. The Pt foil used as the radiation absorber would have the dimensions of 7 × 9 cm² and a thickness of 16 μm that will stop 95% of the radiated power. Two different InSb based IR cameras having a sensitivity of 15 mK are considered for measuring the temperature rise of the foil due to the radiation. The first has 1280 × 1024 pixel² and a frame rate of 105 fps. The second has 640 × 512 pixel² and a frame rate of 1000 fps. The resulting IRVBs have 40 × 30 pixel², 10 ms time resolution, and a signal to noise ratio (SNR) of 17 and 20 × 15 pixel², 3 ms time resolution, and a SNR of 35, respectively. The synthetic image data give SNRs of 30 and 59, respectively.

Signal to noise ratio of upgraded imaging bolometer for KSTAR

An InfraRed imaging Video Bolometer (IRVB) was installed on KSTAR in 2012 having a ∼2 μm × 7 cm × 9 cm Pt foil blackened with graphite and a 5 mm × 5 mm aperture located 7.65 cm from the foil with 16 × 12 channels and a time resolution of 10 ms. The IR camera was an Indigo Phoenix (InSb, 320 × 256 pixels, 435 fps, <25 mK). In 2017, the IRVB was upgraded by replacing the IR camera with a FLIR SC7600 (InSb, 640 × 512 pixels, 105 fps, <25 mK). The aperture area was reduced by approximately half to 3.5 mm × 3.5 mm, and the number of channels was quadrupled to 32 × 24. A synthetic image derived using the projection matrix for the upgraded IRVB from a Scrape Off Layer Plasma Simulator (SOLPS) model with 146 kW of total radiated power had a maximum signal of 7.6 W/m² and a signal to noise ratio (SNR) of 11. Experimental data for a plasma with parameters similar to the SOLPS model (total radiated power of 158 kW) had a maximum signal of 12.6 W/m² and noise equivalent power density (SNR) of 0.9 W/m² (14).