Synthesis of a chitosan/polyvinyl alcohol/activate carbon biocomposite for removal of hexavalent chromium from aqueous solution

A spherical adsorbent produced from a bagasse biochar chitosan assembly for selective adsorption of platinum-group metals from wastewater

This study addresses the challenge of platinum-group metal scarcity by exploring the adsorption of these metals from industrial wastewater. An inexpensive adsorbent with selective platinum-group metal adsorption capacity, named chitosan/citric acid@diatomaceous earth-sugarcane bagasse (CTS/CA@DE-SBS), was newly synthesized. The material features a double coating of chitosan and diatomite on bagasse biochar, and it exhibits an excellent adsorption performance for platinum-group metals due to the synergistic effects of the biochar and chitosan-diatomaceous earth intercross-linked coatings. CTS/CA@DE-SBS achieved an 81 % adsorption efficiency and a static saturated adsorption capacity of 217 mg/g for Pt (IV) in water. Notably, the material exhibited selective adsorption properties for platinum-group metals dissolved in diverse aqueous solutions. The potential for the secondary recovery of platinum-group metals in complex aqueous bodies further underscores the significance of this adsorbent. In conclusion, this research introduces a promising solution for platinum-group metal shortages, offering a cost-effective and selective adsorbent with potential applications in the secondary recovery of these metals from industrial wastewater.

Green magnetic carbon/alginate biocomposite beads from iron scrap waste for efficient removal of textile dye and heavy metal

The circular economy can help enhance the value of industrial waste and remediate the environment. This study considers the application of iron scrap from steel production as a free resource to produce magnetic adsorbent beads to remove methylene blue dye and lead (II) ions from wastewater. Composite beads were prepared by incorporating iron scrap and activated carbon into a calcium alginate gel using a simple 'mix and drop' synthesis. The optimized magnetic beads were stable and offered a large specific surface area. The maximum adsorption capacity of the adsorbent, calculated from the Langmuir isotherm model, was 476.19 mg g-1 for methylene blue and 163.93 mg g-1 for lead (II) ions. This study places emphasis upon the zero-waste principle and employs a scalable synthetic approach for the conversion of waste iron scrap into an adsorbent material capable of delivering significant environmental benefits.

Preparation, characterization, and adsorption kinetics of graphene oxide/chitosan/carboxymethyl cellulose composites for the removal of environmentally relevant toxic metals

This study attempted to develop a low-cost and eco-friendly bio-based composite adsorbent that is highly efficient in capturing potential toxic metals. The bio-composite adsorbent was prepared using graphene oxide (GO), carboxymethyl cellulose (CMC) and chitosan (CS); and characterized using FTIR, SEM-EDX and WAXD techniques. Metal-ion concentration in an aqueous solution was measured by ICP-OES. This article reveals that the adsorption of heavy metal ions varied according to the adsorbent quantity, initial metal concentration, pH, and interaction time. The metal ions' adsorption capacity (mg/g) was observed to increase when the interaction time and metal concentration increased. Conversely, metal ions adsorption was decreased with an increase in adsorbent dosages. The effect of pH on metal ions' adsorption was ion-specific. The substantial adsorption by GO/CMC/CS composite for Co2+, CrO42-, Mn2+ and Cd2+, had the respective values of 43.55, 77.70, 57.78, and 91.38 mg/g under acidic conditions. The metal ions experimental data were best fitted with pseudo-second-order (PSO) kinetics, and Freundlich isotherm model (except Co2+). The separation factors (RL) value in the present investigation were found between 0 and 1, meaning that the metal ions adsorption onto GO/CS/CMC composite is favorable. The RL and sorption intensity (1/n) values fitted well to the adsorption isotherm.

Recent advances in removal of inorganic anions from water by chitosan-based composites: A comprehensive review

Chitosan is a modified natural carbohydrate polymer that has been found in the exoskeletons of crustaceans (e.g., lobsters, shrimps, krill, barnacles, crayfish, etc.), mollusks (octopus, oysters, squids, snails), algae (diatoms, brown algae, green algae), insects (silkworms, beetles, scorpions), and the cell walls of fungi (such as Ascomycetes, Basidiomycetes, and Phycomycetes; for example, Aspergillus niger and Penicillium notatum). However, it is mostly acquired from marine crustaceans such as shrimp shells. Chitosan-based composites often present superior chemical, physical, and mechanical properties compared to single chitosan by incorporating the benefits of both counterparts in the nanocomposites. The tunable surface chemistry, abundant surface-active sites, facilitation synthesize and functionalization, good recyclability, and economic viability make the chitosan-based materials potential adsorbents for effective and fast removal of a broad range of inorganic anions. This article reviews the different types of inorganic anions and their effects on the environment and human health. The development of the chitosan-based composites synthesis, the various parameters like initial concentration, pH, adsorbent dosage, temperature, the mechanism of adsorption, and regeneration of adsorbents are discussed in detail. Finally, the prospects and technical challenges are emphasized to improve the performance of chitosan-based composites in actual applications on a pilot or industrial scale.

PEI-modified chitosan/activated carbon composites for Cu(II) removal from simulated pyrophosphate plating rinsing wastewater

It is a challenging task to remove heavy metal ions efficiently from the wastewater containing high concentrations of complexants. In this work, a novel PEI-modified chitosan/activated carbon composite adsorbent (PCA) was prepared and applied to the removal of Cu(II) from pyrophosphate plating rinsing wastewater. The main species of Cu(II) in the pyrophosphate wastewater was [Cu(HP2O7)2]4- or [Cu(P2O7)2]6-, which were denoted as [Cu(II)-PP] anions. The maximum adsorption capacity of PCA for Cu(II) reached 1.41 mmol g-1 under the condition of pH = 8 and molar ratio of pyrophosphate to Cu(II) = 4:1. The adsorption kinetic behavior of Cu(II) on PCA followed the Elovich model best and PCA attained adsorption equilibrium within 36 h. The thermodynamic studies showed that the adsorption process of Cu(II) by PCA was endothermic and spontaneous. The PCA fixed bed column was used to remove Cu(II) from simulated pyrophosphate plating rinsing wastewater. After three consecutive adsorption-desorption cycles, the adsorption performance, hydraulic conductivity, and mechanical stability of PCA column did not decrease. The FTIR and XPS analysis results indicated that [Cu(II)-PP] anions can be adsorbed on PCA by electrostatic attraction with protonated amine groups or coordination with the amine groups of PCA via ligand substitution.

Surfactant supported chitosan for efficient removal of Cr(VI) and anionic food stuff dyes from aquatic solutions

In order to develop a novel and cost-effective adsorbent with outstanding adsorption capacity and excellent recyclability for anionic pollutants, the chitosan-modified cetyltrimethylammonium bromide sorbent (CS@CTAB) was fabricated. Fourier-transform infrared spectroscopy, N2 adsorption-desorption isotherm, elemental analysis, Thermogravimetric analysis, X-ray diffraction, and Scanning electron microscopy have been applied to evaluate both raw and surfactant modified chitosan (CS@CTAB). Azorubine, Sunset Yellow, and hexavalent chromium were used to study the adsorption behavior of CS@CTAB under various parameters such as adsorbent dose, initial dye and metal ion concentration, contact time, and temperature. Adsorption equilibrium, kinetics models and thermodynamic parameters were investigated. The adsorption isotherm fitted well with the Langmuir isotherm model, with a maximum adsorption capacity of 492.6 mg/g, 492.6 mg/g, and 490.196 mg/g for Azorubine, Sunset Yellow, and Hexavalent Chromium, respectively. The kinetic studies showed that the pseudo-second-order model provided a better correlation between experimental data. Furthermore, the calculated thermodynamic parameters confirmed that the adsorption of Cr(VI), E110, and E122 by CS@CTAB material is a spontaneous and exothermic process. The fabricated CS@CTAB adsorbent was employed for the efficient elimination of Azorubine, Sunset Yellow, and hexavalent chromium from real water samples, synthetic mixtures, and colored soft drinks, with a percentage of recovery of ~ 96%. The plausible adsorption mechanisms of Azorubine, Sunset Yellow, and hexavalent chromium on the surface of CS@CTAB are elucidated. The adsorption anticipated to be due to electrostatic interaction and hydrogen bond formation for hexavalent chromium; while the adsorption of Azorubine and Sunset Yellow, was assumed to be due to electrostatic interaction, hydrogen bonding, and n-π interaction. Finally, the study demonstrates the efficiency of CS@CTAB for the removal of anionic species from several samples, including natural water and colored beverages.

Enhanced adsorptive removal of hexavalent chromium in aqueous media using chitosan-modified biochar: Synthesis, sorption mechanism, and reusability

Hexavalent chromium (Cr(VI)) is deemed a priority contaminant owing to its carcinogenicity, teratogenicity, and mutagenicity towards flora and fauna. A novel Chitosan-modified Mimosa pigra biochar (CMPBC) was fabricated and efficiency of Cr(VI) oxyanion removal in aqueous systems was compared with the pristine biochar. The gross composition of pyrolyzed biomass was determined through the proximate analysis. The instrumental characterization of X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) confirmed the amino modification of MPBC when treated with chitosan. Characteristic features of the Cr(VI) sorptive process by CMPBC and MPBC were examined by performing batch sorption studies. Experimental data suggested that sorption is heavily dependent on pH, with the highest adsorption capacity (14.4 ± 0.9 mg g^-1) occurring at pH 3. It was further noted that the removal efficiency of CMPBC (92%) was considerably greater than that of MPBC (75%) when the biochar dose and initial concentration of Cr(VI) are 1 g L^-1 and 5 mg L^-1 respectively. The kinetic data were best interpreted by the power function model (R² = 0.97) suggesting a homogenous chemisorption process. The isotherm data of removal of Cr(VI) by CMPBC was inferred well by Redlich Peterson and Temkin isotherms. Results of sorption-desorption regeneration cycles indicated that the Cr(VI) uptake by CMPBC is not fully reversible. The electrostatic attractions between cationic surface functionalities and Cr(VI) oxyanions, partial reductive transformation of Cr(VI) species to Cr(III), as well as complexation of Cr(III) onto CMPBC were the possible mechanisms of mitigation of Cr(VI) by CMPBC. The results and outcomes of this research suggest the possibility of utilizing the chitosan-modified Mimosa pigra biochar as an easily available, environmentally sustainable, and inexpensive sorbent to decontaminate Cr(VI) pollution from aqueous media.

A polyurethane foam membrane filled with double cross-linked chitosan/carboxymethyl cellulose gel and decorated with ZSM-5 nano zeolite: Simultaneous dye removal

A novel bio-based polyurethane foam was fabricated using double cross-linked chitosan/carboxymethyl cellulose gel, filled with ZSM-5 nano zeolite, and hot-pressed into the membrane. The prepared foam membrane was characterized using FESEM, FTIR, BET, TGA, and pH_ZPC analyses and then used for continuous dye removal. The results modification of polyurethane foam with chitosan/carboxymethyl cellulose gel and ZSM-5 nano zeolite would increase the retention ability of positive cationic methylene blue. Also, the foam could simultaneously remove methyl orange, eriochrome black T, and methylene blue from the binary and trinary solutions but could effectively be used to selectively removal methylene blue. In addition, the dye removal ability at the breakthrough was enhanced with decreasing flow rate, and increasing bed height, pH, initial dye concentration, and nano zeolite content in the foam. To describe the breakthrough curves different models were utilized which best fits were obtained with Modified Dose-Response as compared to Thomas, Adams & Bohart, Yoon-Nelson, and Wolborska models.

Mn(II) Sorption on Stream Sediments Sampled in Manganese Mining Area: Dynamics and Mechanisms

The stream sediments that have been impacted by manganese (Mn) containing wastewater for decades contain not only abundant microorganisms but also organic/inorganic substances. To achieve effective treatment of manganese (Mn)-containing effluent and recovery of Mn from water/sediments, the Mn(II) sorption behaviors and mechanism on sediments of a stream in Mn mining areas were studied. In addition, the study analyzed the effects of various factors (initial concentration, solution pH, sediment dose, contact time, and coexisting cations) on the Mn sorption efficiency of Daxin sediments, and explored the contribution of microbial activity in the sediment sorption of Mn(II). The results showed that the sorption process of Mn(II) on the sediments was consistent with the Elovich and Freundlich models, and the removal of heavy metals was maximum at 40 °C (62.47–98.93%), pH = 8 (77.51%), initial concentration of 1 mmol·L−1 (95.37%) and sediment dosing of 12 g·L−1 (98.93%). The addition of 50 mM NaN3 inhibited the microbial activity in the Daxin sediment, reducing the sorption and removal rates of Mn(II) by 0.605 mg·g−1 and 8.92%, respectively. After sorption, the proportion of the Fe–Mn oxidation(iron–manganese) state in Daxin sediments decreased from 54% to 43%, while the proportion of the exchangeable state increased by 10.80%. Microorganisms in the sediment had a positive effect on inhibiting heavy metal migration and reducing the bioavailability of contaminants in the soil. Through this study, we hope to further understand the sorption and desorption mechanism of manganese by stream sediments in manganese ore areas, so as to provide a guide on the management and recovery of Mn from stream sediments in manganese mining areas.

Preparation and applications of chitosan and cellulose composite materials

Chitosan is a natural fiber, chemically cellulose-like biopolymer, which is processed from chitin. Its use as a natural polymer is getting more attention because it is non-toxic, renewable, and biocompatible. However, its poor mechanical and thermal strength, particle size, and surface area restrict its industrial use. Consequently, to improve these properties, cellulose and/or inorganic nanoparticles have been used. This review discusses the recent progress of chitosan and cellulose composite materials, their preparation, and their applications in different industrial sectors. It also discusses the modification of chitosan and cellulose composite materials to allow their use on a large scale. Finally, the recent development of chitosan composite materials for drug delivery, food packaging, protective coatings, and wastewater treatment are discussed. The challenges and perspectives for future research are also considered. This review suggests that chitosan and cellulose nano-composite are promising, low-cost products for environmental remediation involving a simple production process.

Application of magnetic chitosan nanocomposites modified by graphene oxide and polyethyleneimine for removal of toxic heavy metals and dyes from water

A new type of magnetic chitosan nanocomposites modified with graphene oxide and polyethyleneimine (MCS/GO-PEI) was synthesized, which was used as an adsorbent to remove the toxic heavy metals of As and Hg as well as anionic azo dyes of congo red and amaranth in environmental water. In this experiment, MCS/GO-PEI was first synthesized and the structure and morphology characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier-transform infrared spectrometry (FT-IR), X-ray diffractometer (XRD), vibrating sample magnetometry (VSM) and X-ray photoelectron spectroscopy (XPS). The adsorption performance of the material for four analytes was investigated through adsorption experiments. The kinetic and isothermal results showed that the adsorption process was well described by pseudo-second-order kinetic and Langmuir isotherm model. Besides, the important parameter pH in the adsorption process was investigated and optimized. The maximum adsorption capacities of the nanocomposites for arsenic, mercury ions, congo red, amaranth were 220.26, 124.84, 162.07, 93.81 mg g^-1 under optimum adsorption conditions, respectively. The adsorption-desorption showed that the adsorbents were presented adequate reusability. The as-prepared MCS/GO-PEI nanocomposite could serve as promising adsorbent for arsenic, mercury, congo red and amaranth in environmental water samples treatment technology.

Fly ash modified magnetic chitosan-polyvinyl alcohol blend for reactive orange 16 dye removal: Adsorption parametric optimization

A magnetic biocomposite blend of chitosan-polyvinyl alcohol/fly ash (m-Cs-PVA/FA) was developed by adding fly ash (FA) microparticles into the polymeric matrix of magnetic chitosan-polyvinyl alcohol (m-Cs-PVA). The effectiveness of m-Cs-PVA/FA as an adsorbent to remove textile dye (reactive orange 16, RO16) from aquatic environment was evaluated. The optimum adsorption key parameters and their significant interactions were determined by Box-Behnken Design (BBD). The analysis of variance (ANOVA) indicates the significant interactions can be observed between m-Cs-PVA/FA dose with solution pH, and m-Cs-PVA/FA dose with working temperature. Considering these significant interactions, the highest removal of RO16 (%) was found 90.3% at m-Cs-PVA/FA dose (0.06 g), solution pH (4), working temperature (30 °C), and contact time (17.5 min). The results of adsorption kinetics revealed that the RO16 adsorption was better described by the pseudo-second-order model. The results of adsorption isotherm indicated a multilayer adsorption process as well described by Freundlich model with maximum adsorption capacity of 123.8 mg/g at 30 °C. An external magnetic field can be easily applied to recover the adsorbent (m-Cs-PVA/FA). The results supported that the synthesized m-Cs-PVA/FA presents itself as an effective and promising adsorbent for textile dye with preferable adsorption capacity and separation ability during and after the adsorption process.

Adsorption of Hexavalent Chromium and Divalent Lead Ions on the Nitrogen-Enriched Chitosan-Based Activated Carbon

Optimizing the physicochemical properties of the chitosan-based activated carbon (Ch-ACs) can greatly enhance its performance toward heavy metal removal from contaminated water. Herein, Ch was converted into a high surface area (1556 m2/g) and porous (0.69 cm3/g) ACs with large content of nitrogen (~16 wt%) using K2CO3 activator and urea as nitrogen-enrichment agents. The prepared Ch-ACs were tested for the removal of Cr(VI) and Pb(II) at different pH, initial metal ions concentration, time, activated carbon dosage, and temperature. For Cr(VI), the best removal was at pH = 2, while for Pb(II) the best pH for its removal was in the range of 4-6. At 25 °C, the Temkin model gives the best fit for the adsorption of Cr(VI), while the Langmuir model was found to be better for Pb(II) ions. The kinetics of adsorption of both heavy metal ions were found to be well-fitted by a pseudo-second-order model. The findings show that the efficiency and the green properties (availability, recyclability, and cost effectiveness) of the developed adsorbent made it a good candidate for wastewaters treatment. As preliminary work, the prepared sorbent was also tested regarding the removal of heavy metals and other contaminations from real wastewater and the obtained results were found to be promising.

An Innovative Method of Converting Ferrous Mill Scale Wastes into Superparamagnetic Nanoadsorbents for Water Decontamination

The need to recycle and develop nanomaterials from waste, and use them in environmental applications has become increasingly imperative in recent decades. A new method to convert the mill scale, a waste of the steel industry that contains large quantity of iron and low impurities into a nanoadsorbent that has the necessary properties to be used for water purification is presented. The mill scale waste was used as raw material for iron oxide nanopowder. A thorough characterization was performed in each stage of the conversion process from the mill scale powder to magnetic nanopowder including XRD (X-ray diffraction), SEM (scanning electron microscopy), TEM (transmission electron microscopy), BET (Brunauer, Emmett and Teller) and magnetization properties. Iron oxide nanoparticles were approximately 5-6 nm with high specific surface area and good magnetic properties. These are the necessary properties that a magnetic nanopowder must have in order to be used as nanoadsorbents in the heavy metal removal from waters. The iron oxide nanoparticles were evaluated as adsorbents for the removal of Cu, Cd and Ni ions.

Eco-Friendly Adsorbent from Waste of Mint: Application for the Removal of Hexavalent Chromium

A serious environmental disaster is looming on the horizon due to the indiscriminate release of heavy metals into the soil and wastewater from human industrial practices. In this study, waste mint (WM) was used to remove chromium(VI) from aqueous solution using batch experiments. The adsorbent material (WM) was characterized using scanning electron microscopy coupled with energy dispersive analysis of X-ray spectroscopy (SEM-EDS), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The adsorption parameters optimized were as follows: pH solution (2–11), initial concentration of Cr(VI) (10–50 mg/L), adsorbent dose (0.1–10 g/L), and temperature conditions (298 K, 308 K, and 318 K). The experimental data fitted well to the fractional power kinetic model (0.97≤R2≤ 0.99) and Langmuir isotherm (R2 = 0.984) with a maximum adsorption capacity Qmax = 172.41 mg/g. The thermodynamic parameters for Cr(VI) sorption were also calculated, confirming that the adsorption process was spontaneous and accompanied by an exothermic adsorption (−4.83 ≤ ΔG ≤ −3.22 kJ/mol and ΔH = −28.93 kJ/mol). The Cr(VI) removal percentage was within the range of 41–98%, and the highest removal was noted at pH = 2. The results of the present study suggest that WM is a potential low-cost adsorbent for the removal of chromium(VI) from aqueous solutions.

Recent Developments in Chitosan-Based Adsorbents for the Removal of Pollutants from Aqueous Environments

The quality of water is continuously under threat as increasing concentrations of pollutants escape into the aquatic environment. However, these issues can be alleviated by adsorbing pollutants onto adsorbents. Chitosan and its composites are attracting considerable interest as environmentally acceptable adsorbents and have the potential to remove many of these contaminants. In this review the development of chitosan-based adsorbents is described and discussed. Following a short introduction to the extraction of chitin from seafood wastes, followed by its conversion to chitosan, the properties of chitosan are described. Then, the emerging chitosan/carbon-based materials, including magnetic chitosan and chitosan combined with graphene oxide, carbon nanotubes, biochar, and activated carbon and also chitosan-silica composites are introduced. The applications of these materials in the removal of various heavy metal ions, including Cr(VI), Pb(II), Cd(II), Cu(II), and different cationic and anionic dyes, phenol and other organic molecules, such as antibiotics, are reviewed, compared and discussed. Adsorption isotherms and adsorption kinetics are then highlighted and followed by details on the mechanisms of adsorption and the role of the chitosan and the carbon or silica supports. Based on the reviewed papers, it is clear, that while some challenges remain, chitosan-based materials are emerging as promising adsorbents.