Preparation of highly diffusible porous cross-linked lipase B from Candida antarctica conjugates: Advances in mass transfer and application in transesterification of 5-Hydroxymethylfurfural

Combined cross-linking of Rhizomucor miehei lipase and Candida antarctica lipase B for the effective enrichment of omega-3 fatty acids in fish oil

The incorporation of a non-specific lipase and a sn-1,3 specific one in a single immobilized system can be a promising approach for the exploitation of both lipases. A one-step immobilization platform mediated by an isocyanide-based multi-component reaction was applied to create co-cross-linked enzymes (co-CLEs) of lipases from Rhizomucor miehei (sn-1,3 specific) and Candida antarctica (non-specific). Glutaraldehyde was found to be effective cross-linker by producing specific activity of 16.9 U/mg and immobilization yield of 99 %. High activity recovery of up to 404 % was obtained for immobilized derivatives. Leaking experiment showed covalent nature of the cross-linking processes. BSA had considerable effect on the immobilization process, providing 87-100 % immobilization yields and up to 10 times improvement in the specific activity of the immobilized derivatives. Scanning electron microscopy images showed flower-like and rod-like structures for the CLEs prepared by glutaraldehyde and undecanedicarboxylic acid, respectively. The prepared co-CLEs were examined in non-selective enrichment of eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA) from fish oil, showing capability of releasing up to 100 % of both omega-3 fatty acids within 8 h of the reaction. The reusability of co-CLEs in five successive cycles presented retaining 63-72 % of their initial activities after the fifth reuse cycle in the hydrolysis reaction.

An Overview of Crosslinked Enzyme Aggregates: Concept of Development and Trends of Applications

Enzymes are commonly used as biocatalysts for various biological and chemical processes in industrial applications. However, their limited operational stability, catalytic efficiency, poor reusability, and high-cost hamper further industrial usage. Thus, crosslinked enzyme aggregates (CLEAs) are developed as a better enzyme immobilization tool to extend the enzymes' operational stability. This immobilization method is appealing because it is simpler due to the absence of ballast and permits the collective use of crude enzyme cocktails. CLEAs, so far, have been successfully developed using a variety of enzymes, viz., hydrolases, proteases, amidases, lipases, esterases, and oxidoreductase. Recent years have seen the emergence of novel strategies for preparing better CLEAs, which include the combi- and multi-CLEAs, magnetics CLEAs, and porous CLEAs for various industrial applications, viz., laundry detergents, organic synthesis, food industries, pharmaceutical applications, oils, and biodiesel production. To better understand the different strategies for CLEAs' development, this review explores these strategies and highlights the relevant concerns in designing innovative CLEAs. This article also details the challenges faced during CLEAs preparation and solutions for overcoming them. Finally, the trending strategies to improve the preparation of CLEAs alongside their industrial application trends are also discussed.

Advances in enzymatic conversion of biomass derived furfural and 5-hydroxymethylfurfural to value-added chemicals and solvents

The progress of versatile chemicals and bio-based fuels using renewable biomass has gained ample importance. Furfural and 5-hydroxymethylfurfural are biomass-derived compounds that serve as the cornerstone for high-value chemicals and have a myriad of industrial applications. Despite the significant research into several chemical processes for furanic platform chemicals conversion, the harsh reaction conditions and toxic by-products render their biological conversion an ideal alternative strategy. Although biological conversion confers an array of advantages, these processes have been reviewed less. This review explicates and evaluates notable improvements in the bioconversion of 5-hydroxymethylfurfural and furfural to comprehend the current developments in the biocatalytic transformation of furan. Enzymatic conversion of HMF and furfural to furanic derivative have been explored, while the latter has substantially overlooked a foretime. This discrepancy was reviewed along with the outlook on the potential usage of 5-hydroxymethylfurfural and furfural for the furan-based value-added products' synthesis.

Combined cross-linked enzyme aggregates of cyclodextrin glucanotransferase and maltogenic amylase from Bacillus lehensis G1 for maltooligosaccharides synthesis

Maltooligosaccharides (MOS) are functional oligosaccharides that can be synthesized through enzymatic cascade reaction between cyclodextrin glucanotransferase (CGTase) and maltogenic amylase (Mag1) from Bacillus lehensis G1. To address the problems of low operational stability and non-reusability of free enzymes, both enzymes were co-immobilized as combined cross-linked enzyme aggregates (Combi-CLEAs-CM) with incorporation of bovine serum albumin (BSA) and Tween 80 (Combi-CLEAs-CM-add). Combi-CLEAs-CM and Combi-CLEAs-CM-add showed activity recoveries of 54.12 % and 69.44 %, respectively after optimization. Combi-CLEAs-CM-add showed higher thermal stability at higher temperatures (40 °C) with longer half-life (46.20 min) as compared to those of free enzymes (36.67 min) and Combi-CLEAs-CM (41.51 min). Both combi-CLEAs also exhibited higher pH stability over pH 5 to pH 9, and displayed excellent reusability with >50 % of initial activity retained after four cycles. The reduction in K_m value of about 22.80 % and 1.76-fold increase in starch hydrolysis in comparison to Combi-CLEAs-CM attested the improvement of enzyme-substrate interaction by Tween 80 and pores formation by BSA in Combi-CLEAs-CM-add. The improved product specificity of Combi-CLEAs-CM-add also produced the highest yield of MOS (492 mg/g) after 3 h. Therefore, Combi-CLEAs-CM-add with ease of preparation, excellent reusability and high operational stability is believed to be highly efficacious biocatalyst for MOS production.

Scalability of U-Shape Magnetic Nanoparticles-Based Microreactor–Lipase-Catalyzed Preparative Scale Kinetic Resolutions of Drug-like Fragments

The production of active pharmaceutical ingredients (APIs) and fine chemicals is accelerating due to the advent of novel microreactors and new materials for immobilizing customized biocatalysts that permit long-term use in continuous-flow reactors. This work studied the scalability of a tunable U-shape magnetic nanoparticles (MNPs)-based microreactor. The reactor consisted of a polytetrafluoroethylene tube (PTFE) of various inner diameters (ID = 0.75 mm, 1.50 mm, or 2.15 mm) and six movable permanent magnets positioned under the tube to create reaction chambers allowing the fluid reaction mixture to flow through and above the enzyme-loaded MNPs anchored by permanent magnets. The microreactors with various tube sizes and MNP capacities were tested with the preparative scale kinetic resolution of the drug-like alcohols 4-(3,4-dihydroisoquinolin-2(1H)-yl)butan-2-ol (±)-1a and 4-(3,4-dihydroquinolin-1(2H)-yl)butan-2-ol (±)-1b, utilizing Lipase B from Candida antarctica immobilized covalently onto MNPs, leading to highly enantioenriched products [(R)-2a,b and (S)-1a,b]. The results in the U-shape MNP flow reactor were compared with reactions in the batch mode with CaLB-MNPs using similar conditions. Of the three different systems, the one with ID = 1.50 mm showed the best balance between the maximum loading capacity of biocatalysts in the reactor and the most effective cross-section area. The results showed that this U-shaped tubular microreactor might be a simple and flexible instrument for many processes in biocatalysis, providing an easy-to-set-up alternative to existing techniques.

Evaluating the potential of engineered Trichoderma atroviride and its laccase-mediated system for the efficient bioconversion of 5-hydroxymethylfufural

5-Hydroxymethylfurfural (HMF) is a fermentation inhibitor which is formed during acid-based thermochemical pre-treatment of biomass. The present study involves two approaches for HMF conversion; the first includes screening and identification of fungal strains which produce oxidoreductases for HMF bioconversion, and thereafter evaluating their roles in HMF conversion. Out of the ten fungal strains screened, genetically engineered Trichoderma atroviride (Lac⁺) showed maximum HMF bioconversion and the activities of ligninolytic enzymes produced were noted. Maximum HMF conversion of 99% was achieved at pH 5.0 and 30 °C when 72 h old 10% inoculum of T. atroviride (Lac⁺) was utilized for 6 days. Based on the fungal bioconversion of HMF to 2, 5 diformylfuran with 58% yield, laccase was observed to influence the conversion process. Thus, a comparative study was established on HMF conversion by 100 U/mL of commercial laccases and partially purified laccase from T. atroviride (Lac+). In the presence of TEMPO, T. atroviride laccase showed comparable HMF conversion to commercial laccases, which establishes the efficiency of fungi and ligninolytic enzymes in bioconversion of HMF to value-added products.

A Review on Biotechnological Approaches Applied for Marine Hydrocarbon Spills Remediation

The increasing demand for petroleum products generates needs for innovative and reliable methods for cleaning up crude oil spills. Annually, several oil spills occur around the world, which brings numerous ecological and environmental disasters on the surface of deep seawaters like oceans. Biological and physico-chemical remediation technologies can be efficient in terms of spill cleanup and microorganisms—mainly bacteria—are the main ones responsible for petroleum hydrocarbons (PHCs) degradation such as crude oil. Currently, biodegradation is considered as one of the most sustainable and efficient techniques for the removal of PHCs. However, environmental factors associated with the functioning and performance of microorganisms involved in hydrocarbon-degradation have remained relatively unclear. This has limited our understanding on how to select and inoculate microorganisms within technologies of cleaning and to optimize physico-chemical remediation and degradation methods. This review article presents the latest discoveries in bioremediation techniques such as biostimulation, bioaugmentation, and biosurfactants as well as immobilization strategies for increasing the efficiency. Besides, environmental affecting factors and microbial strains engaged in bioremediation and biodegradation of PHCs in marines are discussed.

Lipase immobilization via cross-linked enzyme aggregates: Problems and prospects - A review

In this review we have focused on the preparation of cross-linked enzyme aggregates (CLEAs) from lipases, as these are among the most used enzyme in bioprocesses. This immobilization method is considered very attractive due to preparation simplicity, non-use of supports and the possibility of using crude enzyme extracts. CLEAs provide lipase stabilization under extreme temperature or pH conditions or in the presence of organic solvents, in addition to preventing enzyme leaching in aqueous medium. However, it presents some problems in the preparation and limitations in their use. The problems in preparation refer mainly to the crosslinking step, and may be solved using an aminated feeder. The problems in handling have been tackled designing magnetic-CLEAs or trapping the CLEAs in particles with better mechanical properties, the substrate diffusion problems has been reduced by producing more porous-CLEAs, etc. The enzyme co-immobilization using combi-CLEAs is also a new tendency. Therefore, this review explores the CLEAs methodology aimed at lipase immobilization and its applications.

Insolubilization of Tramates versicolor laccase as cross-linked enzyme aggregates for the remediation of trace organic contaminants from municipal wastewater

The novelty of this study deals with the biocatalytic treatment of trace organic contaminants (TrOCs) from municipal wastewater by insolubilized laccase. Laccase from Trametes versicolor was aggregated by three-phase partitioning technique followed by cross-linking with glutaraldehyde to produce insolubilized laccase as cross-linked enzyme aggregates (CLEAs). The optimal conditions for CLEAs preparation include ammonium sulphate concentration of 83% (w/v), crude to t-butanol ratio of 1.00: 1.05 (v/v), pH 5.3, and glutaraldehyde concentration of 20 mM obtained via statistical design. The efficiency of insolubilization of the CLEAs laccase based on the k_cat/k_m ratio was approximately 4.8-fold greater than that of free laccase. The developed CLEAs showed greater resistance to product inhibition mediated by ABTS than the free enzyme and exhibited excellent catalytic activity even after the tenth successive cycle. Further, free laccase and the synthesized CLEAs laccase were utilized to treat five analgesics, two NSAIDS, three antibiotics, two antilipemics, and three pesticides in the municipal wastewater. Under the batch process with operating conditions of pH 7.0 and 20 °C, 1000 U/L of CLEAs, laccase removed 11 TrOCs in the range of about 20-99%. However, the inactivated CLEAs only adsorbed 2-25% of TrOCs. It was observed that acetaminophen, mefenamic acid, trimethoprim, and metolachlor depicted almost complete removal with CLEAs laccase. The performance of CLEAs laccase in a perfusion basket reactor was tested for the removal of TrOCs from municipal wastewater.

Cross-linked enzyme aggregates immobilization: preparation, characterization, and applications

Enzymes are commonly used as biocatalysts for various biological and chemical processes. However, some major drawbacks of free enzymes (e.g. poor reusability and instability) significantly restrict their industrial practices. How to overcome these weaknesses remain considerable challenges. Enzyme immobilization is one of the most effective ways to improve the reusability and stability of enzymes. Cross-linked enzyme aggregates (CLEAs) has been known as a novel and versatile carrier-free immobilization method. CLEAs is attractive due to its simplicity and robustness, without purification. It generally shows: high catalytic specificity and selectivity, good operational and storage stabilities, and good reusability. Moreover, co-immobilization of different kinds of enzymes can be acquired. These CLEAs advantages provide opportunities for further industrial applications. Herein, the preparation parameters of CLEAs were first summarized. Next, characterization of structural and catalytic properties, stability and reusability are also proposed. Finally, some important applications of this technique in: environmental protection, industrial chemistry, food industry, and pharmaceutical synthesis and delivery are introduced. Potential challenges and future research directions, such as improving cross-linking efficiency and internal mass transfer efficiency, are also presented. This implies that CLEAs provide an efficient and feasible technique to improve the properties of enzymes for use in the industry.