TiO2/rectorite-trapped cellulose composite nanofibrous mats for multiple heavy metal adsorption

Properties and environmental sustainability of fungal chitin nanofibril reinforced cellulose acetate films and nanofiber mats by solution blow spinning

Materials from biological origin composed by renewable carbon facilitate the transition from linear carbon-intensive economy to a sustainable circular economy. Accordingly, we use solution blow spinning to develop fully biobased cellulose acetate films and nanofiber mats reinforced with fungal chitin nanofibrils (ChNFs), an emerging bio-colloid with lower carbon footprint compared to crustacean-derived nanochitin. This study incorporates fungal ChNFs into spinning processes for the first time. ChNF addition reduces film surface roughness, modifies film water affinity, and tailors the nanofiber diameter of the mats. The covalently bonded β-D-glucans of ChNFs act as a binder to improve the interfacial properties and consequently load transference to enhance the mechanical properties. Accordingly, the Young's modulus of the films increases from 200 ± 18 MPa to 359 ± 99 MPa with 1.5 wt% ChNFs, while the elongation at break increases by ~45 %. Life cycle assessment (LCA) is applied to quantify the environmental impacts of solution blow spinning for the first time, providing global warming potential values of 69.7-347.4 kg·CO2-equiv.·kg-1. Additionally, this work highlights the suitability of ChNFs as reinforcing fillers during spinning and proves the reinforcing effect of mushroom-derived chitin in bio-based films, opening alternatives for sustainable materials development beyond nanocelluloses in the near future.

Cellulose-based adsorbent using in mercury detection and removal from water via an efficient grafting strategy of fluorometric sensors by click reaction

Mercury pollution in waters attracts lots of attention due to its serious toxicity and high bioenrichment and many efforts have been devoted in the development of adsorbents for mercury detection and removal. Herein, a cellulose-based adsorbent Cell-TriA-HQ is functionalized with quinoline fluorophore by covalent immobilization through "Click reaction" with high yield. In addition to the admirable adsorptive performance, the prepared adsorbent exhibits excellent selectivity and sensitivity towards Hg (II) in water that the detection limit for Hg (II) is determined to be as low as 1.92 × 10-7 M. The sensitive fluorescence enhancement response is considered to be resulted from the inhibition of photo-induced electron transfer between triazole and quinoline groups and the reinforcement of structural rigidity. The easy manipulation along with excellent performance of adsorption capacity, detective ability and reusability for the multifunctional adsorbent makes it potential in mercury monitoring and removal from aqueous solutions in the field of water treatment.

Sol-Gel-Derived TiO2 and TiO2/Cu Nanoparticles: Synthesis, Characterization, and Antibacterial Efficacy

This study reports on the antibacterial efficacy of both the TiO2 and TiO2/Cu nanoparticles prepared through the sol-gel method. The materials were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET) analysis. The SEM and TEM showed the spherical morphology of the nanoparticles, while EDX and XPS confirmed the incorporation of Cu into the TiO2 nanoparticles. The XRD confirmed the formation of the tetragonal anatase phase of TiO2/Cu while the FTIR revealed the functional groups linked to the doped TiO2 nanoparticles. The thermal stability of TiO2/Cu was found to be lower than pure TiO2. Moreover, TiO2 and the doped TiO2 nanoparticles were notably effective against Bacillus subtilis(B. subtilis) andEscherichia coli(E. coli); however, the addition of Cu to TiO2 did not have any effect on the antibacterial activity probably due to the lower weight content in the composites. Interestingly, the antibacterial efficiency was determined to be 90 and 80% against B. subtilis and E. coli, respectively.

Electrospinning and electrospun polysaccharide-based nanofiber membranes: A review

The electrospinning technology has set off a tide and given rise to the attention of a widespread range of research territories, benefiting from the enhancement of nanofibers which made a spurt of progress. Nanofibers, continuously produced via electrospinning technology, have greater specific surface area and higher porosity and play a non-substitutable key role in many fields. Combined with the degradability and compatibility of the natural structure characteristics of polysaccharides, electrospun polysaccharide nanofiber membranes gradually infiltrate into the life field to help filter air contamination particles and water pollutants, treat wounds, keep food fresh, monitor electronic equipment, etc., thus improving the life quality. Compared with the evaluation of polysaccharide-based nanofiber membranes in a specific field, this paper comprehensively summarized the existing electrospinning technology and focused on the latest research progress about the application of polysaccharide-based nanofiber in different fields, represented by starch, chitosan, and cellulose. Finally, the benefits and defects of electrospun are discussed in brief, and the prospects for broadening the application of polysaccharide nanofiber membranes are presented for the glorious expectation dedicated to the progress of the eras.

Tunable structure of TiO2 deposited by DC magnetron sputtering to adsorb Cr (VI) and Fe (III) from water

TiO2 thin films with mixtures of the anatase, rutile, and brookite phases were deposited on glass substrates via magnetron sputtering. Based on XRD and Raman results, the TiO2-0.47 and TiO2-3.47 films principally contained the brookite phase, while the TiO2-1.27 and TiO2-2.13 films were primarily anatase. The capacities of the TiO2 films to adsorb heavy metals were tested with Cr(VI) and Fe(III) solutions, and the maximum Cr(VI) and Fe(III) adsorption capacities were realized with the TiO2-0.47 film (334.5 mg/g) and TiO2-3.47 film (271.3 mg/g), respectively. SEM‒EDS results revealed the presence of Cr and Fe on the surfaces of the films, thus corroborating the ability of the TiO2 films to adsorb and remove heavy metals. They are strong candidates for use in wastewater treatment plants.

Yeast biomass ornamented macro-hierarchical chitin nanofiber aerogel for enhanced adsorption of cadmium(II) ions

There is an urgent need to develop sustainable, renewable, and environment-friendly adsorbents to rectify heavy metals from water. In the current study, a green hybrid aerogel was prepared by immobilizing yeast on chitin nanofibers in the presence of a chitosan interacting substrate. A cryo-freezing technique was employed to construct a 3D honeycomb architecture comprising the hybrid aerogel with excellent reversible compressibility and abundant water transportation pathways for the accelerated diffusion of Cadmium(II) (Cd(II)) solution. This 3D hybrid aerogel structure offered copious binding sites to accelerate the Cd(II) adsorption. Moreover, the addition of yeast biomass amplified the adsorption capacity and reversible wet compression of hybrid aerogel. The monolayer chemisorption mechanism explored by Langmuir and pseudo-second-order kinetic exhibited a maximum adsorption capacity of 127.5 mg/g. The hybrid aerogel demonstrated higher compatibility for Cd(II) ions as compared to the other coexisted ions in wastewater and manifested a better regeneration potential following four consecutive sorption-desorption cycles. Complexation, electrostatic attraction, ion-exchange and pore entrapment were perhaps major mechanisms involved in the removal of Cd(II) revealed by XPS and FT-IR. This study unveiled a novel avenue for efficient green-synthesized hybrid aerogel that may be sustainably used as an excellent purifying agent for Cd(II) removal from wastewater.

Highly fluorescent composite of boron nitride quantum dots decorated on cellulose nanofibers for detection and removal of Hg(II) ions from waste water

To address the challenge of heavy-metal ions in wastewater, boron nitride quantum dots (BNQDs) were synthesized in-situ on rice straw derived cellulose nanofibers (CNFs) as substrate. The composite system exhibited strong hydrophilic-hydrophobic interactions, as corroborated by FTIR, integrated the extraordinary fluorescence properties of BNQDs with fibrous-network of CNFs (BNQD@CNFs) yielding a surface of 35.147 m² g^-1 of luminescent fibers. Morphological studies revealed uniform distribution of BNQDs on CNFs due to hydrogen bonding, according high thermal stability with peak degradation occurring at 347.7 °C and quantum yield of 0.45. The nitrogen-rich surface of BNQD@CNFs exhibited strong affinity for Hg(II), quenching the fluorescence intensity due to combined inner-filter effect and photo-induced electron transfer. The limit of detection (LOD) and limit of quantification (LOQ) were 4.889 nM and 11.1 5 nM, respectively. BNQD@CNFs concomitantly exhibited adsorption of Hg(II) owing to strong electrostatic interactions, confirmed by X-ray photon spectroscopy. Presence of polar BN bonds favoured 96 % removal of Hg(II) at 10 mg L^-1 with maximum adsorption capacity of 314.5 mg/ g. Parametric studies corresponded to pseudo-second order kinetics and Langmuir isotherm with R² ≈ 0.99. BNQD@CNFs exhibited recovery rate between 101.3 %-111 % for real water samples and recyclability upto 5 cycles, demonstrating high potential in wastewater remediation.

Recent advances in the hybridization of cellulose and semiconductors: Design, fabrication and emerging multidimensional applications: A review

Cellulose is a plentiful, biodegradable, renewable, and natural polymer in the world that can be widely utilized in the production of polymer nanocomposites. Cellulose is developed in nanomaterials owing to its remarkable inherent features of low density, non-toxicity, and affordability, as well as the amazing sample characteristics of strength and thermal stability. Recently, there has been a lot of interest in organic-inorganic composites because of their adaptable qualities. Cellulose and semiconductors have exciting properties, and new combinations of both materials may result in efficient functional hybrid composites with distinct properties. Lately, a huge study was reported on cellulose and semiconductor-based nanocomposites. In this review, we summarize the present research development in the preparation methods, structure, features, and possible applications of multifunctional cellulose and semiconductor-based nanocomposites. The cellulose/semiconductor based nanocomposites have massive potential applications in the areas of photodegradation of organic dyes, hydrogen production, metal removal, biomedical, and sensor applications. It is also assumed that this article will promote additional investigation and will establish innovative capabilities to enhance novel cellulose and semiconductor based nanocomposites with new and exciting applications.

Heavy Metal Removal from Aqueous Effluents by TiO2 and ZnO Nanomaterials

The presence of heavy metals in wastewater, such as Ni, Pb, Cd, V, Cr, and Cu, is a serious environmental problem. This kind of inorganic pollutant is not biodegradable for several years, and its harmful effect is cumulative. Recently, semiconductor nanomaterials based on metal oxides have gained interest due to their efficiency in the removal of heavy metals from contaminated water, by inducing photocatalytic ion reduction when they absorb light of the appropriate wavelength. The most commonly applied semiconductor oxides for these purposes are titanium oxide (TiO2), zinc oxide (ZnO), and binary nanomaterials composed of both types of oxides. The main purpose of this work is to critically analyse the existent literature concerning this topic focusing specially in the most important factors affecting the adsorption or photocatalytic capacities of this type of nanomaterials. In particular, photocatalytic activity is altered by various factors, such as proportion of polymorphs, synthesis method, surface area, concentration of defects and particle size, among others. After a survey of the actual literature, it was found that, although these metal oxides have low absorption capacity for visible light, it is possible to obtain an acceptable heavy metal reduction performance by sensitization with dyes, doping with metallic or nonmetallic atoms, introduction of defects, or the coupling of two or more semiconductors.

Effect of calcination temperatures on the performance of rectorite for cadmium immobilization in soil: Freeze-thaw, plant growth, and microbial diversity

The immobilization of cadmium (Cd(II)) in soil using calcined rectorite (REC) was investigated in this research. The results of immobilization show that a small amount of REC calcined at 700 °C (REC-700 °C) could effectively immobilize 90% of Cd(II) in soil, while the immobilization efficiency of REC only reached 42%. Moreover, the immobilization efficiency of REC calcined at 300 °C and 500 °C (REC-300 °C and REC-500 °C) were lower than REC. To investigate the mechanism, the materials before and after immobilization were fully analyzed by Fourier transform infrared spectroscopy (FT-IR), powdery X-ray diffraction analysis (XRD), and scanning electron microscopy (SEM). The results indicate that the structure of REC has been changed after calcination at different temperatures and Cd(II) was successfully immobilized on materials. Losing free water, structural water and OH groups respectively, the layer spacing of REC-300 °C and REC-500 °C was shrunk. However, the crystal structure of REC was destroyed after calcination at 700 °C, resulting in the generation of new phases. According to the XRD result, more cadmium hydroxide (Cd(OH)₂) were produced on REC-700 °C, indicating that more OH groups were formed during immobilization. Furthermore, Tessier test demonstrates that Cd(II) in soil changed from exchangeable state and water soluble state to carbonate bound state and iron manganese oxide bound state during immobilization. The result of microbial community indicates that REC-700 °C can restore the microbial composition of Cd(II)-contaminated soil. The effects of pH, freeze-thaw, REC dosage, and initial heavy metal concentration were also evaluated to provide a theoretical basis for the subsequent application of the material in the remediation of contaminated soil.

Genetically modified metallothionein/cellulose composite material as an efficient and environmentally friendly biosorbent for Cd2+ removal

Metallothioneins (MTs) are a class of cysteine-rich metal-binding proteins. Cadmium (Cd) is one of the toxic heavy metal pollutants. In our previous research, the full-length cDNA of MT (Cd specificity) from freshwater crab (Sinopotamon henanense) (ShMT) was cloned and genetically modified to ShMT3 by site-directed mutagenesis to enhance the tolerance for Cd²⁺, however, it was limited in actual Cd²⁺ adsorption due to instability. Here, ShMT3-CBM, a novel recombinant fusion protein, was prepared. CBM is a carbohydrate binding module that can specifically bind cellulose while ShMT3 can effectively chelate Cd²⁺. The biosorbent Cellulose1-ShMT3-CBM was obtained by screening suitable cellulose materials. The selective adsorption experiments showed that Cellulose1-ShMT3-CBM had a preference for Cd²⁺. In low-concentration Cd²⁺ solutions, the removal efficiency was >99 %, and the adsorption equilibrium was reached within 15 min. The saturated adsorption capacity of Cellulose1-ShMT3-CBM for Cd²⁺ is 180.35 ± 4.67 mg/g (Dry Weight). Regeneration experiments showed that adsorption efficiency was maintained after six cycles. The MTT experiment showed that Cellulose1-ShMT3-CBM had low cytotoxicity. Meanwhile, Cellulose1-ShMT3-CBM can preferentially remove Cd²⁺ in actual water samples and boiler sewage. In this study, an environmentally friendly biosorbent which can adsorb Cd²⁺ efficiently and quickly was prepared for actual water treatment.

Electrospun molecularly imprinted sodium alginate/polyethylene oxide nanofibrous membranes for selective adsorption of methylene blue

Molecular imprinting technique is an efficient method to improve the selective adsorption capacity for the target pollutant. In this study, sodium alginate/polyethylene oxide molecularly imprinted nanofibrous membrane (SA/PEO-MINM) with average diameter of 185 ± 20 nm was successfully synthesized by electrospinning for selective adsorption of methylene blue (MB). Benefiting from the molecular imprinted technology, the adsorption amount of SA/PEO-MINM for MB was increased by about 65%, significantly higher than the non-imprinted membrane. Results showed that the adsorption equilibrium could be well fitted with Langmuir isotherm model and the maximum adsorption capacity towards MB was 3186.7 mg/g. Kinetic experiments well complied with the Pseudo second order model. Reusability studies indicated that the removal efficiency of MB could maintain 93% of the original adsorption capacity after four consecutive adsorption/desorption cycles. More importantly, the SA/PEO-MINM with high surface area and specific adsorption recognition sites showed excellent selective adsorption capacity in the adsorption experiment of MB and methylene orange mixed dye solution. In general, the SA/PEO-MINM can be successfully applied for the selective removal of MB from dye wastewater.

Cellulose-Based Nanofibers Processing Techniques and Methods Based on Bottom-Up Approach-A Review

In the past decades, cellulose (one of the most important natural polymers), in the form of nanofibers, has received special attention. The nanofibrous morphology may provide exceptional properties to materials due to the high aspect ratio and dimensions in the nanometer range of the nanofibers. The first feature may lead to important consequences in mechanical behavior if there exists a particular orientation of fibers. On the other hand, nano-sizes provide a high surface-to-volume ratio, which can have important consequences on many properties, such as the wettability. There are two basic approaches for cellulose nanofibers preparation. The top-down approach implies the isolation/extraction of cellulose nanofibrils (CNFs) and nanocrystals (CNCs) from a variety of natural resources, whereby dimensions of isolates are limited by the source of cellulose and extraction procedures. The bottom-up approach can be considered in this context as the production of nanofibers using various spinning techniques, resulting in nonwoven mats or filaments. During the spinning, depending on the method and processing conditions, good control of the resulting nanofibers dimensions and, consequently, the properties of the produced materials, is possible. Pulp, cotton, and already isolated CNFs/CNCs may be used as precursors for spinning, alongside cellulose derivatives, namely esters and ethers. This review focuses on various spinning techniques to produce submicrometric fibers comprised of cellulose and cellulose derivatives. The spinning of cellulose requires the preparation of spinning solutions; therefore, an overview of various solvents is presented showing their influence on spinnability and resulting properties of nanofibers. In addition, it is shown how bottom-up spinning techniques can be used for recycling cellulose waste into new materials with added value. The application of produced cellulose fibers in various fields is also highlighted, ranging from drug delivery systems, high-strength nonwovens and filaments, filtration membranes, to biomedical scaffolds.

Kinetics, thermodynamics, equilibrium, surface modelling, and atomic absorption analysis of selective Cu(ii) removal from aqueous solutions and rivers water using silica-2-(pyridin-2-ylmethoxy)ethan-1-ol hybrid material

The removal of heavy metals is attracting considerable attention due to their undesirable effects on the environment. In this investigation, a new adsorbent based on silica functionalized with pyridin-2-ylmethanol (SiPy) was successfully synthesized to yield to a hybrid material. FTIR, SEM, TGA, and specific surface area analysis were used to characterize the structure and morphology of the SiPy hybrid material. Various heavy metal ions such as Cu(ii), Zn(ii), Cd(ii), and Pb(ii) were selected to examine the adsorption efficiency of the newly prepared adsorbent, optimized at varying solution pH, contact time, concentration, and temperature. The adsorbent SiPy displayed good adsorption capacity of 90.25, 75.38, 55.23, and 35.12 mg g⁻¹ for Cu(ii), Zn(ii), Cd(ii), and Pb(ii), respectively, at 25 min and pH = 6. The adsorption behaviors of metal ions onto the SiPy adsorbent fitted well with the pseudo-second-order kinetic mode and the isotherm was better described by the Langmuir isotherm. The thermodynamic studies disclose spontaneous and endothermic adsorption process. Furthermore, the SiPy adsorbent retained good selectivity and regeneration properties after five adsorption–desorption cycles of Cu(ii). A computational investigation of the adsorption mechanism indicates that the N-pyridine, O-hydroxyl, and ether O-atoms play a predominant role during the capture of Cu(ii), Zn(ii), Cd(ii), and Pb(ii). This study proposes the SiPy adsorbent as an attractive material for the selective removal of Cu(ii) from real river water and real industrial wastewater.

The removal of heavy metals is attracting considerable attention due to their undesirable effects on the environment.