Effect of polymer source variation on the properties and performance of risperidone microspheres

Hyper-spectra imaging analysis of PLGA microspheres via machine learning enhanced Raman spectroscopy

Long-acting injectables (LAI) offer a cost-effective and patient-centric approach by reducing pill burden and improving compliance, leading to better treatment outcomes. Among various types of long-acting injectables, poly (lactic-co-glycolic acid) (PLGA) microspheres have been extensively investigated and reported in the literature. However, microsphere formulation development is still challenging due to the complexity of PLGA polymer, formulation screening, and processing, as well as time-consuming and cumbersome physicochemical characterization. A further challenge is the limited availability of drug substances in early formulation development. Therefore, there is a need to develop novel and advanced tools that can accelerate the early formulation development. In this manuscript, a novel comprehensive physicochemical characterization approach was developed by integrating Raman microscopy and the machine learning process. The physicochemical properties such as drug loading, particle size and size distribution, content uniformity/heterogeneity, and drug polymorphism of the microspheres can be obtained in a single run, without requiring separate methods for each attribute (e.g., liquid chromatography, particle size analyzer, thermal analysis, X-ray powder diffraction). This approach is non-destructive and can significantly reduce material consumption, sample preparation, labor work, and analysis time/cost, which will greatly facilitate the formulation development of PLGA microsphere products. In addition, the approach will potentially be beneficial in enabling automated high throughput screening of microsphere formulations.

Role of PLGA Variability in Controlled Drug Release from Dexamethasone Intravitreal Implants

Long-acting injectable formulations based on poly(lactide-co-glycolide) (PLGA) have been commercialized for over 30 years in at least 20 FDA-approved products. These formulations offer several advantages, including reduced dosing frequency, improved patient compliance, and maintenance of therapeutic levels of drug. Despite extensive studies, the inherent complexity of the PLGA copolymer still poses significant challenges associated with the development of generic formulations having drug release profiles equivalent to those of the reference listed drugs. In addition, small changes to PLGA physicochemical properties or the drug product manufacturing process can have a major impact on the drug release profile of these long-acting formulations. This work seeks to better understand how variability in the physicochemical properties of similar PLGAs affects drug release from PLGA solid implants using Ozurdex (dexamethasone intravitreal implant) as the model system. Four 50:50, acid-terminated PLGAs of similar molecular weights were used to prepare four dexamethasone intravitreal implants structurally equivalent to Ozurdex. The PLGAs were extensively characterized by using a variety of analytical techniques prior to implant manufacture using a continuous, hot-melt extrusion process. In vitro release testing of the four structurally equivalent implants was performed in both normal saline and phosphate-buffered saline (PBS), yielding drastically different results between the two methods. In normal saline, no differences in the release profiles were observed. In PBS, the drug release profiles were sensitive to small changes in the residual monomer content, carboxylic acid end group content, and blockiness of the polymers. This finding further underscores the need for a physiologically relevant in vitro release testing method as part of a robust quality control strategy for PLGA-based solid implant formulations.

The Impact of Post-Processing Temperature on PLGA Microparticle Properties

PURPOSE

Biodegradable poly(lactide-co-glycolide) (PLGA) microparticles loaded with either risperidone or naltrexone were prepared from an emulsification homogenization process. The objective of this study was to determine the impact the post-treatment temperature has on the properties and subsequent performance of the microparticles.

METHODS

The post-treatment temperature of an ethanolic solution was characterized from 10 ~ 35ºC for the naltrexone and risperidone micropartilces.

RESULTS

The wash temperature resulted in a typical triphasic in vitro release pattern at low wash temperatures or a biphasic pattern consisting of an elevated release rate at higher post-treatment temperatures. The post-treatment temperature largely influences the particle morphology, residual solvent levels, glass transition temperature, and drug loading and is molecule dependent, whereby these characteristics subsequently influence the drug release rate.

CONCLUSION

The study highlights the importance of both the post-treatment process and control during manufacturing to obtain a formulation within the desired product profile.

In situ forming risperidone implants: Effect of PLGA attributes on product performance

Despite the unique advantages of injectable, long-acting in situ forming implant formulations based on poly(lactide-co-glycolide) (PLGA) and N-Methyl-2-Pyrrolidone (NMP), only six products are commercially available. A better understanding of PLGA will aid in the development of more in situ forming implant innovator and generic products. This article investigates the impact of slight changes in PLGA attributes, i.e., molecular weight (MW), lactide:glycolide (L/G) ratio, blockiness, and end group, on the in vitro and in vivo performance of PLGA-based in situ forming implant formulations. Perseris (risperidone) for extended-release injectable suspension was selected as the reference listed drug (RLD). A previously developed adapter-based USP 2 method was used for the in vitro release testing of various risperidone implant formulations. A rabbit model was used to determine the in vivo pharmacokinetic profiles of the formulations (subcutaneous administration) and deconvolution (Loo-Riegelman method) was conducted to obtain the in vivo release profiles. The results showed that a 5 KDa difference in the MW (19.2, 24.2, 29.2 KDa), a 5% variation in the L/G ratio (85/15, 80/20, 75/25) and the end-cap (acid vs ester) all significantly impacted the formulation behavior both in vitro and in vivo. Higher MW, higher L/G ratio and ester end-cap PLGA all resulted in longer release durations. The formulations prepared with polymers with different blockiness values (within the blockiness range tested) did not show differences in in vitro and in vivo release. An in vitro-in vivo correlation (IVIVC) was not developed due to the different in vitro and in vivo phase separation rates, swelling tendencies and consequent significantly different release profiles. This is the first report evaluating the impact of PLGA property variation (over a narrow range) on the performance of in situ forming implants. The knowledge gained will provide a better understanding of the mechanisms underlying risperidone in situ forming implant performance and will aid the development of future products.

Scanning Analysis of Sequential Semisolvent Vapor Impact To Study Naltrexone Release from Poly(lactide-co-glycolide) Microparticles

Poly(lactide-co-glycolide) (PLGA)-based microparticle formulations have been a mainstay of long-acting injectable drug delivery applications for decades. Despite a long history of use, tools and techniques to analyze and understand these formulations are still under development. Recently, a new characterization method was introduced known as the surface analysis after sequential semisolvent impact using sequential semisolvent vapors. The vapor-based technique is named, for convenience, surface analysis of (semisolvent) vapor impact (SAVI). In the SAVI method, discretely controlled quantities of selected organic semisolvents in the vapor phase were applied to PLGA microparticles to track particle morphological changes by laser scanning confocal microscopy. Subsequently, the morphological images were analyzed to calculate mean peak height (Sa), core height (Sk), kurtosis (Sku), dale void volume (Vvv), the density of peaks (Spd), maximum height (Hm), and the shape ratio (Rs). Here, the SAVI method was applied to naltrexone-loaded microparticles manufactured internally and Vivitrol, a commercial formulation. SAVI analysis of these microparticles indicated that the two primary mechanisms controlling the naltrexone release were the formation of discrete, self-crystallized portions of naltrexone within the PLGA structure and the degradation of PLGA chains through nucleophilic substitution. The relatively higher amounts of naltrexone crystals resulted in prolonged release than lower amounts of crystals. Data from gel permeation chromatography, differential scanning calorimetry, and in vitro release measurements all point to the importance of naltrexone crystal formation. This study highlights the utility of SAVI for gaining further insights into the microstructure of PLGA formulations and using SAVI data to support research, product development, and quality control applications for microparticle formulations of pharmaceuticals.

Implications of particle size on the respective solid-state properties of naltrexone in PLGA microparticles

A thorough understanding of the complexities in formulating and manufacturing polymeric microspheres is required for new and generic drug applications. Specifically, for an ANDA application for polymeric microsphere-based products, the applicant must meet Q1 (qualitative) and Q2 (quantitative) sameness, and in some cases, Q3 (e.g., microstructural) sameness. Herein, we report the naltrexone crystallinity in a PLGA microparticle system prepared from a dichloromethane-benzyl alcohol solvent system results in a crystallinity dependence as a function of microparticle size from the same batch - illustrating intrabatch microstructural variability. As the particle size increases, the crystallinity increases, with additional polymorphic forms more readily noted at the large particle sizes. Furthermore, during dissolution, a polymorphic transition and/or crystallization occurs at larger size fractions. This study highlights the importance of controlling the manufacturing parameters during microparticle formation, specifically solvent extraction and particle size control. Furthermore, with the approval of generic microparticles formulations on the horizon, this study highlights the importance of Q3, the same components in the same concentration with the same arrangement of matter, whereby microparticles can have varying microstructural properties across particle sizes from the same batch.

Bridging the gap between fundamental research and product development of long acting injectable PLGA microspheres

INTRODUCTION

Long acting Injectable PLGA microspheres have gained more and more interest and attention in the field of life cycle management of pharmaceutical products due to their biocompatibility and biodegradability. So far, a multitude of trial-and-error experiments at lab scale have been used for establishing the correlation relationship between critical process parameters, critical material attributes and critical quality attributes. However, few published studies have elaborated on the development of PLGA microspheres from an industrial perspective.

AREAS COVERED

In this review, the scale-up feasibility of translational technologies of PLGA microspheres manufacturing have been evaluated. Additionally, state-of-the-art of technologies and facilities in PLGA development have been summarized. Meanwhile, the industrial knowledge matrix of PLGA microspheres development and research are establishing which provide comprehensive insight for understanding properties of PLGA microspheres as controlled/sustained release vehicle.

EXPERT OPINION

There is still big gap between fundamental research in academic institute and product development in pharmaceuticals. Therefore, the difference and connection between them should be identified gradually for better understanding of PLGA microspheres development.

Transitioning from a lab-scale PLGA microparticle formulation to pilot-scale manufacturing

The complexity of scale-up manufacturing of PLGA microparticles creates a significant challenge when transitioning from benchtop-scale formulation development into larger clinical scale batches. Minor changes in the initial formulation composition (e.g., PLGA molecular weight, solvent type, and drug concentration) and processing parameters (e.g., extraction kinetics and drying condition) during scale-up production can result in significantly different performance of the prepared microparticles. The objectives of the present study were to highlight the in vitro and in vivo performance of a candidate benchtop-scale batch created with a rotor-stator mixer, transitioned into an in-line manufacturing process at ~15× scale of a long-acting naltrexone formulation. Physicochemical properties (such as drug loading, residual benzyl alcohol content, and morphology) as well as the in vitro release characteristics of the prepared naltrexone microparticles between the benchtop-scale and in-line process pilot-scale were determined. The pharmacokinetics of the naltrexone microspheres were investigated using the rat model. The results demonstrate that while the morphologies of the particles were different from a visual assessment and slight differences were observed in the in vitro release profiles, the in vivo pharmacokinetics illustrate similar kinetics. Our study shows that scale-up production having the same drug release kinetics can be made by controlling the formulation and processing parameters.

In vitro-in vivo correlation of PLGA microspheres: Effect of polymer source variation and temperature

Development of Level A in vitro-in vivo correlations (IVIVCs) remains challenging for complex long-acting parenterals, such as poly(lactic-co-glycolic acid) PLGA microspheres. The nature of the PLGA polymer excipient has a dominant influence on the performance of PLGA microspheres. These microsphere systems typically exhibit multiphasic in vitro/in vivo release/absorption characteristics and may also show interspecies differences (animal model versus human data). These issues contribute to the difficulties in the development of IVIVCs for PLGA microsphere systems. To gain a better understanding of how to achieve IVIVCs for PLGA microspheres, microsphere formulations with similar as well as different release characteristics were prepared using PLGAs from different sources. Efforts were then made to establish IVIVCs for these formulations using in vitro release profiles obtained at both 37°C (human body temperature) and 39°C (rabbit body temperature) with in vivo data obtained from an animal model (rabbit). Risperidone was selected as the model drug; microsphere formulations were prepared under the same processing methods using apparently similar PLGAs from different sources. Owning to the different physicochemical properties of the PLGAs (such as inherent viscosity, monomer ratio (L/G ratio) and blockiness), the formulations exhibited significant differences in critical quality attributes (such as particle size, particle size distribution, porosity and pore size) and consequently had different in vitro and in vivo performance. IVIVCs were developed and it was shown that model predictability improved when IVIVCs were established using those formulations with comparable release characteristics. In addition, IVIVCs were established with T_scaling factors close to 1 using in vitro release profiles acquired at 39°C, emphasizing the importance of considering the body temperature in understanding interspecies differences. The present work provides a comprehensive understanding of the impact of the PLGA source variation on IVIVC development and predictability for complex long-acting parenterals such as PLGA microspheres.