Determination of feed forces to improve process understanding of Fused Deposition Modeling 3D printing and to ensure mass conformity of printed solid oral dosage forms

Polyvinyl Alcohol, a Versatile Excipient for Pharmaceutical 3D Printing

Three-dimensional (3D) printing in the pharmaceutical field allows rapid manufacturing of a diverse range of pharmaceutical dosage forms, including personalized items. The application of this technology in dosage form manufacturing requires the judicious selection of excipients because the selected materials must be appropriate to the working principle of each technique. Most techniques rely on the use of polymers as the main material. Among the pharmaceutically approved polymers, polyvinyl alcohol (PVA) is one of the most used, especially for fused deposition modeling (FDM) technology. This review summarizes the physical and chemical properties of pharmaceutical-grade PVA and its applications in the manufacturing of dosage forms, with a particular focus on those fabricated through FDM. The work provides evidence on the diversity of dosage forms created using this polymer, highlighting how formulation and processing difficulties may be overcome to get the dosage forms with a suitable design and release profile.

Texture analysis – a versatile tool for pharmaceutical evaluation of solid oral dosage forms

In the past few decades, texture analysis (TA) has gained importance as a valuable method for the characterization of solid oral dosage forms. As a result, an increasing number of scientific publications describe the textural methods that evaluate the extremely diverse category of solid pharmaceutical products. Within the current work, the use of texture analysis in the characterization of solid oral dosage forms is summarised with a focus on the evaluation of intermediate and finished oral pharmaceutical products. Several texture methods are reviewed regarding the applications in mechanical characterization, and mucoadhesion testing, but also in estimating the disintegration time and in vivo specific features of oral dosage forms. As there are no pharmacopoeial standards for pharmaceutical products tested through texture analysis, and there are important differences between reported results due to different experimental conditions, the choice of testing protocol and parameters is challenging. Thereby, this work aims to guide the research scientists and quality assurance professionals involved in different stages of drug development into the selection of optimal texture methodologies depending on the product characteristics and quality control needs.

3D printing of amorphous solid dispersions: A comparison of fused deposition modeling and drop-on-powder printing

Nowadays, a high number of pipeline drugs are poorly soluble and require solubility enhancement by e.g., manufacturing of amorphous solid dispersion. Pharmaceutical 3D printing has great potential in producing amorphous solid oral dosage forms. However, 3D printing techniques differ greatly in terms of processing as well as tablet properties. In this study, an amorphous formulation, which had been printed via Fused Deposition Modeling and drop-on-powder printing, also known as binder jetting, was characterized in terms of solid-state properties and physical stability. Solid state assessment was performed by differential scanning calorimetry, powder X-ray diffraction and polarized microscopy. The supersaturation performance of the amorphous solid dispersion was assessed via non-sink dissolution. We further evaluated both 3D printing techniques regarding their processability as well as tablet uniformity in terms of dimension, mass and content. Challenges and limitations of each 3D printing technique were discussed. Both techniques are feasible for the production of amorphous formulations. Results indicated that Fused Deposition Modeling is better suited for production, as the recrystallization tendency was lower. Still, filament production and printing presented a major challenge. Drop-on-powder printing can be a viable alternative for the production of amorphous tablets, when a formulation is not printable by Fused Deposition Modeling.

An Additive Manufacturing Direct Slicing Algorithm Based on a STEP Model

The Standard Template Library (STL) file is the most common data format for the description of an additive manufacturing (AM) geometric model, but it has some disadvantages, such as large errors of the geometric model description, the easy loss of topology information, data duplication, large file sizes, and so on. Aiming at these problems, a direct slicing algorithm based on a Standard for the Exchange of Product Model Data (STEP) model was proposed. For the parts composed of basic types of surfaces such as boundary curves, spherical surfaces and cylindrical surfaces, the traditional geometric method was used to calculate the intersection. For the parts with complex surfaces, the three-dimensional models were described based on Non-Uniform Rational B-Spline (NURBS) surfaces. The NURBS surfaces were layered using a discrete tracking algorithm, the tracking starting point was determined, the intersection line between the tangent plane and each NURBS sub-surface was obtained, and the closed layer contour was formed. Finally, the slicing simulations and printing experiments of solid parts were carried out using the direct slicing algorithm based on the STEP model. It was shown that the dimensional accuracy and surface quality of the printed parts from this algorithm had been significantly improved.