Revised adaptive active disturbance rejection sliding mode control strategy for vertical stability of active hydro-pneumatic suspension

Adaptive differential steering strategy for distributed driving unmanned ground vehicle with variable configurations based on modified localized modelling sliding mode control

When performing complex tasks such as position transfer and material transportation, the distributed driving unmanned platform with variable configurations needs to address the challenge of multi-wheel cooperative torque distribution control to achieve high-performance differential steering and enhance vehicle dynamics. The configuration change will impact the dynamic performance of the unmanned platform, posing a challenge to the performance of the existing control strategy based on mathematical model development. In order to address the aforementioned issues, this paper analyzes the impact of changes in vehicle configuration on steering gain and proposes a hierarchical adaptive differential steering strategy based on variable vehicle configurations. Firstly, the response characteristics of the yaw angle relative to the active yaw moment under the influence of changes in wheelbase and tread are analyzed. Based on this analysis, two structural modes, maneuverable and balanced, are selected. Secondly, a localized-modelling sliding mode control method with an extended state observer is proposed to estimate the desired yaw moment in the upper controller, considering the motor's execution delay. Then, the lower controller optimizes the torque of each wheel in real-time using the whale optimization algorithm. It aims to optimize tire energy dissipation and tire load rate while ensuring driving stability and achieving differential steering. Finally, through co-simulation and experiments on a scaled prototype, the reliability of the dynamics theory and the superiority of the control algorithm are validated. This optimization has led to significant improvements in the tire dissipation energy index and tire load rate index.

Research on Electric Oil-Pneumatic Active Suspension Based on Fractional-Order PID Position Control

In this study, an electric oil and gas actuator based on fractional-order PID position feedback control is proposed, through which the damping coefficient of the suspension system is adjusted to realize the active control of the suspension. An FOPID algorithm is used to control the motor's rotational angle to realize the damping adjustment of the suspension system. In this process, the road roughness is collected by the sensors as the criterion of damping adjustment, and the particle swarm algorithm is utilized to find the optimal objective function under different road surface slopes, to obtain the optimal cornering value. According to the mathematical and physical model of the suspension system, the simulation model and the corresponding test platform of this type of suspension system are built. The simulation and experimental results show that the simulation results of the fractional-order nonlinear suspension model are closer to the actual experimental values than those of the traditional linear suspension model, and the accuracy of each performance index is improved by more than 18.5%. The designed active suspension system optimizes the body acceleration, suspension dynamic deflection, and tire dynamic load to 89.8%, 56.7%, and 73.4% of the passive suspension, respectively. It is worth noting that, compared to traditional PID control circuits, the FOPID control circuit designed for motors has an improved control performance. This study provides an effective theoretical and empirical basis for the control and optimization of fractional-order nonlinear suspension systems.

Backstepping integral sliding mode control for pneumatic manipulators via adaptive extended state observers

In this paper, a nonlinear control strategy is proposed for a pneumatic manipulator based on an adaptive extended state observer and a backstepping integral sliding mode controller. A single degree of freedom dynamic model is established for the pneumatic manipulator using an Euler-Lagrange dynamic equation. The adaptive extended state observer is designed by an adaptive law to estimate uncertainties and disturbances. The backstepping integral sliding mode controller is proposed using an integral sliding mode surface based on backstepping technique. Comparative experiments verify effectiveness of the proposed nonlinear control strategy for the pneumatic manipulator.

Fast Distributed Model Predictive Control Method for Active Suspension Systems

In order to balance the performance index and computational efficiency of the active suspension control system, this paper offers a fast distributed model predictive control (DMPC) method based on multi-agents for the active suspension system. Firstly, a seven-degrees-of-freedom model of the vehicle is created. This study establishes a reduced-dimension vehicle model based on graph theory in accordance with its network topology and mutual coupling constraints. Then, for engineering applications, a multi-agent-based distributed model predictive control method of an active suspension system is presented. The partial differential equation of rolling optimization is solved by a radical basis function (RBF) neural network. It improves the computational efficiency of the algorithm on the premise of satisfying multi-objective optimization. Finally, the joint simulation of CarSim and Matlab/Simulink shows that the control system can greatly minimize the vertical acceleration, pitch acceleration, and roll acceleration of the vehicle body. In particular, under the steering condition, it can take into account the safety, comfort, and handling stability of the vehicle at the same time.