Adaptation of a clinical fixation device for biomechanical testing of the lumbar spine

Biomechanical Analysis of Wide Posterior Releases Compared With Inferior Facetectomy and Discectomy in the Thoracolumbar and Lumbar Spine

STUDY DESIGN

In vitro biomechanical analysis.

OBJECTIVES

Compare the destabilizing effects of anterior discectomy to posterior spinal releases.

SUMMARY OF BACKGROUND DATA

Posterior release and pedicle screw fixation has become the accepted form of treatment for lumbar and thoracolumbar pediatric scoliotic spinal deformity. A biomechanical evaluation of posterior releases with comparison to traditional anterior releases has not been reported in the lumbar spine.

METHODS

Eleven fresh-frozen human thoracolumbar specimens (T9-L5) were tested by a robotic manipulator (Staubli RX90; moment target of 5.0 Nm, force target of 50 N) in axial rotation (AR), plus lateral and anterior translation (LT and AT). Specimens underwent either sequential anterior release (partial and full discectomy) or posterior release (inferior facetectomy and wide posterior release) from T10 to L4. Partial discectomy retained the posterior 50% of disc and posterior longitudinal ligament, whereas full discectomy removed all of the disc and PLL. Wide posterior release included total facetectomy plus ligamentum flavum and spinous process resection.

RESULTS

Inferior facetectomy produced an average increase of 1.5° ± 1.0° (p = .0625), 1.0 ± 0.8 mm (p = .0313), and 0.2 ± 0.3 mm (p = .156) in AR, LT, and AT, respectively. Compared with partial facetectomy, wide posterior release produced an average additional increase of 8.1° ± 4.0° (p = .0312), 2.0 ± 2.2 mm (p = .4062), and 1.1 ± 1.0 mm (p = .0625) in AR, LT, and AT, respectively. Full discectomy produced 201%, 161%, and 153% of the motion relative to wide posterior release in AR, LT, and AT, respectively (p = .0043, .0087, and .0173). Partial discectomy and wide posterior release proved statistically equivalent.

CONCLUSIONS

Wide posterior release of the thoracolumbar spine allows significant correction and may be superior to inferior facetectomy in axial rotation. Although complete discectomy with PLL resection would likely allow greater correction, a more clinically realistic partial discectomy confers similar corrective potential in vitro compared with wide posterior release.

LEVEL OF EVIDENCE

Not applicable.

Internal Biomechanical Study of a 70-Year-Old Female Human Lumbar Bi-Segment Finite Element Model and Comparison with a Middle-Aged Male Model

The main purpose of this article is to study the biomechanics of spine tissue in elderly female. In this study, the L3-L5 lumbar bi-segmental finite element model for elderly female was obtained from the Advanced Human Modeling Laboratory of the Bioengineering Center at Wayne State University. The effects of flexion and extension on bone geometry, distribution of ligament fibers, location of nucleus, and changes in intervertebral disc height were studied by comparing the results obtained before and after the update of older female and middle-aged male models. For the purpose of comparing the calculated range of motion (ROM) with the experimental data, additional calculations for axial rotation and lateral bending were performed. The study found that the parameters of the model affected the deformation of the disc herniation, ligament and intervertebral disc, and the axial force carrying capacity of the model. The three predicted ROMs are usually similar to the experimental results. Only the older female model has a slightly larger ROM. Therefore, older women are more vulnerable to lumbar spine injuries than men.

Influence of follower load application on moment-rotation parameters and intradiscal pressure in the cervical spine

The objective of this study was to implement a follower load (FL) device within a robotic (universal force-moment sensor) testing system and utilize the system to explore the effect of FL on multi-segment cervical spine moment-rotation parameters and intradiscal pressure (IDP) at C45 and C56. Twelve fresh-frozen human cervical specimens (C3-C7) were biomechanically tested in a robotic testing system to a pure moment target of 2.0 Nm for flexion and extension (FE) with no compression and with 100 N of FL. Application of FL was accomplished by loading the specimens with bilateral cables passing through cable guides inserted into the vertebral bodies and attached to load controlled linear actuators. FL significantly increased neutral zone (NZ) stiffness and NZ width but resulted in no change in the range of motion (ROM) or elastic zone stiffness. C45 and C56 IDP measured in the neutral position were significantly increased with application of FL. The change in IDP with increasing flexion rotation was not significantly affected by the application of FL, whereas the change in IDP with increasing extension rotation was significantly reduced by the application of FL. Application of FL did not appear to affect the specimen's quantity of motion (ROM) but did affect the quality (the shape of the curve). Regarding IDP, the effects of adding FL compression approximates the effect of the patient going from supine to a seated position (FL compression increased the IDP in the neutral position). The change in IDP with increasing flexion rotation was not affected by the application of FL, but the change in IDP with increasing extension rotation was, however, significantly reduced by the application of FL.