Fruit waste-derived cellulose and graphene-based aerogels: Plausible adsorption pathways for fast and efficient removal of organic dyes

Construction of manganese ferrite/zinc ferrite anchored graphene-based hierarchical aerogel photocatalysts following Z-scheme electron transfer for visible-light-driven carbon dioxide reduction

Herein, atomic-level interfacial coupling between spinel-type MnFe2O4 (MFA) and ZnFe2O4 (ZFA) was achieved via a sol-gel method combined with phase separation. These composites were then anchored onto a three-dimensional graphene aerogel (GA) through ethylenediamine-assisted hydrothermal self-assembly, forming a hierarchically porous MFA/ZFA@GA with a high surface area (191.06 m2/g). The optimized MFA/ZFA@GA exhibited a CO production rate of 21.14 μmol·g-1·h-1 (96 % selectivity, 94 % stability) under visible light, a 3.87-fold enhancement over single-component systems. The in-situ MFA/ZFA heterojunction and graphene-enhanced electron transfer synergistically prolonged photogenerated electron lifetime by 10 times. The hierarchical pores also boosted CO2 adsorption (7.66 wt%), the appreciable saturation magnetization intensity (37.49 emu/g) enabled magnetic separation recovery, and *COOH monitoring confirmed rapid desorption kinetics for high CO selectivity. Experiments combined with theoretical calculations revealed a Z-scheme mechanism: MnFe2O4's reductive electrons (-0.79 V vs. NHE) drove CO2 reduction, while ZnFe2O4's oxidative holes (1.50 V vs. NHE) facilitated H2O oxidation. Strategic integration of heterostructures, carbon hybridization, and aerogel architectures offered an efficient pathway for monolithic photocatalyst design.

High-performance amino-crosslinked phosphorylated microcrystalline cellulose/MoS2 hybrid aerogel for polystyrene nanoplastics removal from aqueous environments

Currently, the development of high-performance adsorbents for the removal of nanoplastics in complex aquatic environments is challenging. In this study, a functionalized polyethyleneimine-phosphorylated microcrystalline cellulose/MoS2 (PEI-PMCC/MoS2) hybrid aerogel was prepared and applied to remove carboxyl-modified polystyrene (PS-COOH) nanoplastics from the aqueous solution. Benefiting from the introduced functional groups and the expanded lamellar structure in MoS2 nanosheets as well as the highly porous 3D structure of the aerogel, PEI-PMCC/MoS2 demonstrated high efficiency in PS-COOH nanoplastics removal, achieving a 402.4 ± 7.5 mg/g maximum adsorption capacity at the optimal adsorption pH of 7.0 (C0 = 300 mg/L). The adsorption isotherm and kinetics data fitted well with the Langmuir and pseudo-second-order models, respectively, suggesting that the removal of PS-COOH nanoplastics was dominated by the monolayer chemisorption process, and the thermodynamic studies revealed the exothermic nature of the spontaneous adsorption process. Furthermore, the adsorption performance of PEI-PMCC/MoS2 in different complex aqueous environments, as well as its reusability, was evaluated, and the interactions between PEI-PMCC/MoS2 and PS-COOH nanoplastics were analyzed to elaborate the adsorption mechanism. These results confirmed the high nanoplastics removal efficiency and favorable reusability in PEI-PMCC/MoS2, laying a solid foundation for developing high-performance adsorbents for nanoplastics removal.

Hydrophobic Pedicularis Kansuensis/graphene aerogel with solar thermal effect enables efficient removal of sulfadiazine and oil from water

The contamination of water resources by organic pollutants is a significant factor contributing to the scarcity of water resources. Furthermore, the various forms and quantities of organic pollutants present a considerable challenge to their management and remediation. Antibiotics and oil are two typical organic pollutants in water, which have a serious impact on the environment and biological health. It is thus imperative to eradicate these two principal pollutants from the aquatic environment. The remediation of polluted water by adsorption represents an effective approach, with the adsorbent's performance determining the process's efficacy. In this study, Pedicularis Kansuensis/graphene aerogel (PKGA) was prepared, and its adsorption performance of sulfadiazine (SDZ) with low concentration and oil with high concentration was investigated. The results demonstrated that PKGA has good adsorption and removal ability for both SDZ and oil in water. The porous structure, hydrophobicity, and oleophilicity of PKGA facilitate the effective elimination of organic contaminants from aqueous media. The adsorption of SDZ by PKGA is an endothermic spontaneous process. The equilibrium adsorption of SDZ by PKGA increased with increasing temperature and the theoretical maximum equilibrium adsorption at 35 °C was 70.67 mg/g. Additionally, the adsorption capacity of PKGA for oil ranged from 51.27 to 120.71 g/g, indicating its potential for oil-water separation. Notably, PKGA, a representative carbon-based material, exhibits a photothermal effect that enhances its adsorption capabilities for removing SDZ and viscous oil from water. This study offers a novel perspective on organic pollutant adsorption and removal in water.

Biodegradable taro stem cellulose aerogel: A simple approach for adsorbing microplastics and dyestuffs contaminants

Water pollution and agricultural waste are pressing global issues. Herein, a biomass aerogel derived from waste taro stem microcrystalline cellulose (TS-MCC) was fabricated, in which, the effects of cellulose amount, cross-linker content, pre-freezing protocols on the aerogel's property were studied. The optimized TS-MCC2.0 aerogel exhibited a hierarchical porous structure with good mechanical property (65.04 kPa) and adsorption capacities, with the qm towards microplastics (Polystyrene, PS) and dye (Congo red, CR) being 418.6 mg/g and 951.51 mg/g at 298 K, respectively. Meanwhile, it exhibited good applicability under different pH (3-11) and ionic strength environments, as well as the retained notably simultaneous adsorption ability even under mixed contaminant systems. The mathematical models suggested that the adsorption of PS and CR both fitted pseudo-second-order kinetics, and the adsorption isotherms could be described by the Langmuir and Freundlich models, respectively. Hydrogen bonding, electrostatic attraction, and π-π interactions were inferred as the main adsorption mechanisms towards PS and CR according to Fourier transform infrared spectrometer and X-ray photoelectron spectroscopy analysis. Moreover, the adsorption efficiencies were 92.37 % for PS and 88.34 % for CR after 5 reuse cycles. Therefore, this study provides a green aerogel sorbent for adsorbing microplastics and dyes contaminants.

Enhanced removal of emerging contaminants from tap water by developing graphene oxide and nanoplatelet hybrid aerogels

The removal of emerging contaminants (ECs) from drinking water is a current challenge of global concern. Graphene-based sorbents are attracting increasing interest in this field owing to the chemical versatility of graphene-based materials, their commercial availability and processability in various 3D structures. Herein, for the first time, graphene aerogels (GAs) are reported based on the synergy of graphene oxide (GO) and graphene nanoplatelets (GNPs) derived from waste tire and their use as a sorbent for a mixture of ECs in tap water. Reduction of GO up to 52.1% (O/C = 0.092) was demonstrated through X-ray photoelectron spectroscopy, whereas no changes in the GNP structure during aerogel synthesis were demonstrated with comprehensive spectroscopic and microscopic characterisation. Adsorption of a selection of ECs in a mixture from tap water was tested under flow conditions by inserting the aerogels into filtration cartridges and filtering tap water spiked with the mixture of ECs. Remarkably, the GO + GNP aerogel showed an increase in adsorption capacity of about 2.3 times that of the rGO aerogel owing to the higher obtained surface area, 27 instead of 16 m2 g-1, and the resultant more-reduced structure.

Facile synthesis of a 3D magnetic graphene oxide/Fe3O4/banana peel-derived cellulose composite aerogel for the efficient removal of tetracycline

Many initiatives have incorporated graphene oxide (GO) and biomass into aerogels for wastewater treatment. We report on the facile fabrication of a magnetic GO/Fe3O4/banana peel-derived cellulose (bio-cellulose) aerogel using an ultrasound-assisted mechanical mixing method and freeze-drying technique for the removal of tetracycline (TC). The component materials and composite aerogel were characterized using Fourier-transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD), Raman spectroscopy, field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), nitrogen adsorption-desorption analysis, and vibrating sample magnetometry (VSM). The effects of solution pH and adsorbent dose on the adsorption performance of the synthesized adsorbents were investigated. The adsorption behavior at the equilibrium of the GO/Fe3O4/bio-cellulose aerogel was studied and analyzed using four well-known non-linear models: Langmuir, Freundlich, Sips, and Temkin. The results showed that the experimental data fitted well with the Freundlich and Sips isotherm models. The maximum adsorption capacity achieved from the Sips model was 238.7 mg g-1. The adsorption kinetics were studied and proved to follow the Elovich kinetic model with an initial rate of 0.89 g g-1 min-1. These results confirm the favorable adsorption of TC on the heterogeneous surface that exhibits a wide range distribution of adsorption energies of the desired GO/Fe3O4/bio-cellulose aerogel. The experimental findings demonstrate that the aerogel possesses the notable features of environmental friendliness, cost-effectiveness, and comparatively high TC adsorption capacity. Therefore, utilizing biomass to develop the structure of the magnetic GO-based composite aerogel is significantly promising for antibiotic-containing wastewater treatments.

Application of Anionic Hydrogels from Date Palm Waste for Dye Adsorption in Wastewater Treatment

This work aimed to develop an anionic cellulose nanofiber (CNF) bio-adsorbent from date palm tree waste and to investigate its removal efficiency compared to cationic methylene blue dye from contaminated water. Date palm pulp was first prepared from date palm leaves through acid hydrolysis using H2SO4, followed by hydrolysis in a basic medium using KOH, in which the process completely removed the components of hemicellulose, lignin, and silica. To obtain anionic CNF, the resulting pulp was further treated with H2SO4, followed by centrifugation. Biogel formation of the CNF suspension was promoted by sonication, where its removal efficiency of methylene blue dye was studied as a function of dye concentration, temperature, contact time, and pH value. In this work, we investigated two isotherms, i.e., Langmuir and Freundlich. The Langmuir model's consistency with the experimental data suggests that the adsorption of methylene blue dye onto CNF is monolayer and surface-limited. The reported maximum removal efficiency of 5 mg/g at 60 °C indicates the optimal temperature for adsorption in this specific case. Additionally, a pseudo-second-order model and Elovich model were also utilized to obtain a better understanding of the adsorption mechanism, in which we found not just physical adsorption but also an indication of a chemical reaction occurring between methylene blue dye and CNF. According to the results, that pseudo-second-order model's consistency with the experimental data suggests that the adsorption of methylene blue (MB) onto CNF is rate-limiting step involving chemisorption between the two. The study reveals that CNF adsorbents derived from renewable natural waste sources such as date palm leaves can be effective in removing cationic contaminants such as methylene blue dye.

Gels for Water Remediation: Current Research and Perspectives

The development of cost-effective and high-performance technologies for wastewater treatment is essential for achieving a sustainable economy. Among the various methods available for water remediation, adsorption is widely recognized as an effective and straightforward approach for removing a range of pollutants. Gel materials, particularly hydrogels and aerogels, have attracted significant research interest due to their unique properties. Hydrogels, for instance, are noted for their ability to be regenerated and reused, ease of separation and handling, and suitability for large-scale applications. Additionally, their low cost, high water absorption capacity, and contribution to environmental protection are important advantages. Aerogels, on the other hand, are distinguished by their low thermal conductivity, transparency, flexibility, high porosity, mechanical strength, light weight, large surface area, and ultralow dielectric constant. This review provides a comprehensive analysis of the current literature, highlighting gaps in knowledge regarding the classification, preparation, characterization, and key properties of these materials. The potential application of hydrogels and aerogels in water remediation, particularly in removing contaminants such as dyes, heavy metals, and various organic and inorganic pollutants, is also discussed.

Effect of pyrolysis temperature on characteristics and chloramphenicol adsorption performance of NH2-MIL-53(Al)-derived amine-functionalized porous carbons

Several activities such as aquaculture, human and feedstock therapies can directly release antibiotics into water. Due to high stability, low hydrolysis and non-biodegradation, they can accumulate in the aqueous environment and transport to aquatic species. Here, we synthesized amine-functionalized porous carbons (ANC) by a direct-pyrolysis process of NH2-MIL-53(Al) as a sacrificial template at between 600 and 900 °C and utilized them to eliminate chloramphenicol antibiotic from water. The NH2-MIL-53(Al)-derived porous carbons obtained high surface areas (304.7-1600 m2 g-1) and chloramphenicol adsorption capacities (148.3-261.5 mg g-1). Several factors such as hydrogen bonding, Yoshida hydrogen bonding, and π-π interaction, hydrophobic interaction possibly controlled adsorption mechanisms. The ANC800 could be reused four cycles along with high stability in structure. As a result, NH2-MIL-53(Al)-derived porous carbons are recommended as recyclable and efficient adsorbents to the treatment of antibiotics in water.

Multifunctional amphibious superhydrophilic-oleophobic cellulose nanofiber aerogels for oil and water purification

Aerogels are of a popular choice for oil-water separation and water purification due to their attractive properties, such as lightweight, large surface area, and high porosity. Developing robust aerogels with multifunctional characteristics is highly desirable but remains challenging nowadays. Herein, we develop a facile one-pot condensation strategy for the fabrication of superhydrophilic-oleophobic (SHI-OP) composite aerogels using cellulose nanofibers (CNF), 3-glycidy-loxypropyl trimethoxysilane (GPTMS), polyethyleneimine (PEI) and fluorine-contained compound (FS-60). The resulted aerogels exhibit a directional lamellar structure with interconnected macropores, super-lightweight with high porosity of 98.30 % and low density of 0.0256 g·cm-3. Also, the aerogels are mechanically durable against repeated compression. Meanwhile, the amphibious SHI-OP feature of the composite aerogels in both air and water states enables them to not only absorb trace amount of water from contaminated oils, but also separate oil-water mixtures with separation efficiency of over 99 % and high permeation flux of over 9060 L/m2·h. Moreover, the aerogels also show excellent dye adsorption capability and reusability toward anionic dyes with a maximum adsorption capacity of 1245.68 mg/g. Such robust and multifunctional aerogels with special surface wettability provide good opportunity for liquid purification and dye-containing wastewater treatment.

Valorization of sugarcane bagasse with in situ grown MoS2 for continuous pollutant remediation and microbial decontamination

In this study, sugarcane bagasse (SB) was strategically subjected to a delignification process followed by the in situ growth of multi-layered molybdenum disulfide (MoS2) nanosheets with hexagonal phase (2H-phase) crystal structure via hydrothermal treatment. The MoS2 nanosheets underwent self-assembly to form nanoflower-like structures in the aligned cellulose inter-channels of delignified sugarcane bagasse (DSB), the mechanism of which was understood through FTIR and XPS spectroscopic studies. DSB, due to its porous morphology and abundant hydroxyl groups, shows remediation capabilities of methylene blue (MB) dye through physio-sorption but shows a low adsorption capacity of 80.21 mg/g. To improve the removal capacity, DSB after in situ growth of MoS2 (DSB-MoS2) shows enhanced dye degradation to 114.3 mg/g (in the dark) which further improved to 158.74 mg/g during photodegradation, due to catalytically active MoS2. Interestingly, DSB-MoS2 was capable of continuous dye degradation with recyclability for three cycles, reaching an efficiency of > 83%, along with a strong antibacterial response against Gram-positive Staphylococcus aureus (S.aureus) and Gram-negative Escherichia coli (E. coli). The present study introduces a unique strategy for the up-conversion of agricultural biomass into value-added bio-adsorbents, which can effectively and economically address the remediation of dyes with simultaneous microbial decontamination from polluted wastewater streams.

Fruit waste-derived cellulose-polyaniline composite for adsorption-coupled reduction of chromium oxyanions

Hexavalent chromium oxyanions, known as potentially toxic micropollutants, exist in the effluents and discharges of metallurgical, electroplating, refractory, chemical, and tanning industries. The exposure of chromium-contaminated water causes severe health hazards. The present work outlines a facile approach to grow polyaniline (PANI) on fruit-waste-derived cellulose (CEL) via oxidative polymerization of aniline; followed by chemical processing with NH4OH to obtain CEL-PANI-EB composites for adsorptive separation-coupled reduction of highly toxic hexavalent chromium oxyanions. The spectroscopic analyses of the CEL-PANI-EB composite before and after adsorption of Cr(VI) oxyanions revealed hydrogen bonding, electrostatic, and complexation as major interactive pathways. The adsorbed hexavalent chromium oxyanions are reduced into Cr(III) species by oxidation of PANI-based benzenoid amine into quinoid imine in the CEL-PANI-EB composite. The adsorption of Cr(VI) oxyanions by the CEL-PANI-EB composite showed negligible effects of other anionic co-pollutants, like NO3- and SO42-. The CEL-PANI-EB composite adsorbed Cr(VI) oxyanions with a removal capacity of 469 mg g-1, based on the Langmuir adsorption isotherm model. The hydroxyl functionalities in cellulose and amine/imine functionalities in PANI facilitate the electrostatic attraction between the CEL-PANI-EB and Cr(VI) oxyanions in an acidic environment beside the hydrogen linkages. The adsorbed Cr(VI) oxyanions are reduced to Cr(III)-based species by the benzenoid amines of PANI, as revealed from the XPS analyses. The CEL-PANI-EB composite showed excellent recyclability and maintained 83.4% adsorption efficiency after seven runs of chromium adsorption-desorption. The current findings reveal the potential of CEL-PANI-EB composites for the adsorptive removal of Cr(VI) oxyanions and their conversion into a lesser toxic form, making them promising materials for wastewater treatment applications.

Mechanisms and factors affecting the removal of minocycline from aqueous solutions using graphene-modified resorcinol formaldehyde aerogels

In recent years, concerns about the presence of pharmaceutical compounds in wastewater have increased. Various types of residues of tetracycline family antibiotic compounds, which are widely used, are found in environmental waters in relatively low and persistent concentrations, adversely affecting human health and the environment. In this study, a resorcinol formaldehyde (RF) aerogel was prepared using the sol-gel method at resorcinol/catalyst ratio of 400 and resorcinol/water ratio of 2 and drying at ambient pressure for removing antibiotics like minocycline. Next, RF aerogel was modified with graphene and to increase the specific surface area and porosity of the modified sample and to form the graphene plates without compromising the interconnected porous three-dimensional structure of the aerogel. Also, the pores were designed according to the size of the minocycline particles on the meso- and macro-scale, which bestowed the modified sample the ability to remove a significant amount of the minocycline antibiotic from the aqueous solution. The removal percentage of the antibiotic obtained by UV-vis spectroscopy. Ultimately, the performance of prepared aerogels was investigated under various conditions, including adsorbent doses (4-10 mg), solution pHs (2-12), contact times of the adsorbent with the adsorbate (3-24 h), and initial concentration of antibiotic (40-100 mg/l). The results from the BET test demonstrated that the surface area of the resorcinol formaldehyde aerogel sample, which included 1 wt% graphene (RF-G1), exhibited an augmentation in comparison to the surface area of the pure aerogel. Additionally, it was noted that the removal percentage of minocycline antibiotic for both the unmodified and altered samples was 71.6% and 92.1% at the optimal pH values of 4 and 6, respectively. The adsorption capacity of pure and modified aerogel for the minocycline antibiotic was 358 and 460.5 mg/g, respectively. The adsorption data for the modified aerogel was studied by the pseudo-second-order model and the results obtained from the samples for antibiotic adsorption with this model revealed a favorable fit, which indicated that the chemical adsorption in the rapid adsorption of the antibiotic by the modified aerogel had occurred.

Treating waste with waste: Adsorption of anionic dyes in wastewater with surfactant-modified phosphogypsum

Phosphogypsum (PG) is a solid waste generated during the wet process of phosphoric acid production. The environmental-friendly disposal and recycling of PG is vital in the field of environmental solid waste treatment. In this study, PG is used for adsorbent of dyes in wastewater to achieve the goal of recycling waste with waste. Surfactant-modified phosphogypsum (ODBAC@PG) was prepared using octadecyl dimethyl benzyl ammonium chloride (ODBAC) as modifier. ODBAC@PG exhibits high adsorption capability for anionic dyes (methyl blue (MeB) and indocyanine carmine (IC)). The pseudo-second-order kinetic model fits the kinetic experimental data for the adsorption of two organic anionic dyes. Langmuir adsorption isotherm fits the adsorption characteristics of MeB and IC on ODBAC@PG, exhibiting a monolayer adsorption pattern. Thermodynamic parameters indicate the spontaneous and exothermic properties of MeB and IC on ODBAC@PG. MeB and IC have antagonistic effects on each other in binary adsorption system. High adsorption capacity after six cycles of experiments demonstrates the high reusability of ODBAC@PG. The nature for the adsorption includes electrostatic interaction, hydrogen bond and hydrophobic interaction. Using ODBAC@PG for dyes wastewater treatment can accomplish the goal of treating waste with waste and turning waste into treasure.

Characterization of an Iron-Copper Bimetallic Metal-Organic Framework for Adsorption of Methyl Orange in Aqueous Solution

Iron-based organic frame material MIL-53 (Fe) was synthesized by the hydrothermal method with Cu2+ incorporated to obtain bimetallic composite MIL-53 (Fe, Cu). The structure and morphology of the material were characterized by SEM, XRD, BET, FTIR, XPS, and zeta potential. The adsorption performance of MIL-53 (Fe, Cu) on methyl orange was tested under a variety of conditions, including the effects of pH and material dosage, by the static adsorption test. The results show that under the condition of pH = 7, a temperature of 30°C, and an adsorbent dosage of 20 mg, the removal rate of MIL-53 (Fe, Cu) for methyl orange can reach more than 96% within 4 h, and the maximum adsorption capacity after fitting by the thermodynamic model can reach 294.43 mg/g, showing the excellent adsorption performance of MIL-53 (Fe, Cu) on methyl orange. In addition, by exploring the adsorption mechanism of MIL-53 (Fe, Cu) on methyl orange, it is found that the adsorption of MIL-53 (Fe, Cu) on methyl orange depends on chemical adsorption, as evidenced by combining Fe3+ and Cu2+ in the material with methyl orange molecules to form complexes to achieve adsorption. While the specific surface area of the material had no obvious effect on adsorption, the effects of pH, temperature, and concentration were explored. At a pH of 6.5, greater adsorption occurred at higher temperatures, as determined by thermodynamic model fitting, as well as with higher initial methyl orange molecule concentration.

Effective utilization of discarded reverse osmosis post-carbon for adsorption of dyes from wastewater

In this study, the deployment of post Reverse Osmosis (RO)-carbon as a adsorbent for dye removal from water has been investigated. The post RO-carbon was thermally activated (RO900), and the material thus obtained exhibited high surface area viz. 753 m2/g. In the batch system, the efficient Methylene Blue (MB) and Methyl Orange (MO) removal was obtained by using 0.08 g and 0.13 g/50 mL adsorbent dosage respectively. Moreover, 420 min was the optimized equilibration time for both the dyes. The maximum adsorption capacities of RO900 for MB and MO dyes were 223.29 and 158.14 mg/g, respectively. The comparatively higher MB adsorption was attributed to the electrostatic attraction between adsorbent and MB. The thermodynamic findings revealed the process as spontaneous, endothermic, and accompanied by entropy increment. Additionally, simulated effluent was treated, and >99% dye removal efficiency was achieved. To mimic an industrial perspective, MB adsorption onto RO900 was also carried out in continuous mode. The initial dye concentration and effluent flow rate were among the process parameters that were optimized using the continuous mode of operation. Further, the experimental data of continuous mode was fitted with Clark, Yan, and Yoon-Nelson models. Py-GC/MS investigation revealed that dye-loaded adsorbents could be pyrolyzed to produce valuable chemicals. The cost and low toxicity associated benefits of discarded RO-carbon over other adsorbents reveal the significance of the present study.

Combination mechanism of the ternary composite based on Fe3O4-chitosan-graphene oxide prepared by solvothermal method

Magnetic nanohybrid combining chitosan and graphene have demonstrated promising application in environmental remediation. Herein, ternary composite MCG based on Fe₃O₄, chitosan (CS) and graphene oxide (GO) was facilely prepared via solvothermal method. The as prepared composite was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), Raman, Brunauer/Emmett/Teller-Barret/Joyner/Halenda (BET-BJH) and thermo gravimetric-differential thermal analysis (TG-DTA). The combination mechanism of MCG was unveiled via employing the hard-soft acid-base (HSAB) theory and spectroscopic investigations including X-ray photoelectron spectroscopy (XPS), Ultraviolet-visible (UV-Vis) and fluorescent emission spectra. Particularly, combination mechanism of MCG was elucidated by the probable site to site interaction of the couplet components in MCG, as follows. (1) CS-Fe₃O₄. The primary interaction is N(NH₂)-Fe(III), electron donates from N to Fe, transforming one half of the amino groups of chitosan into positive N⁺. (2) GO-CS. Amidation reaction is the primary interaction form, converting the other half of the amino groups of chitosan into -C(O)NH-. (3) GO-Fe₃O₄. Dominant interactions are those of epoxy, hydroxyl and aromatic ring with Fe(III). Moreover, MCG exhibits fair adsorption performance on divalent heavy metals in six consecutive cycles. These explorations may shed light on the design of efficient adsorbent based on Fe₃O₄-chitosan-graphene architecture.

Adsorptive removal of multiple organic dyes from wastewater using regenerative microporous carbon: Decisive role of surface-active sites, charge and size of dye molecules

Present work addresses the synthesis of microporous activated carbon (SDAC) by a facile thermochemical conversion of teak sawdust powder. The high surface area (1999 m² g^-1), excellent microporosity (average pore size: 2.62 nm), and turbostratic carbon structure with intertwined graphitic domains make SDAC a highly efficient adsorptive material for the removal of organic pollutants. The spectroscopic analyses (FTIR, Raman, and XPS) and adsorption locator calculations revealed multiple interactions between organic dyes and SDAC adsorbent, i.e., electrostatic, π-π, n-π interactions, and hydrogen linkages. The size, chemical functionalities, aromatic rings, electronegative and heteroatoms in dye molecules, along with the surface-active sites, microstructured and textural features of SDAC adsorbent collectively governed the interaction pathways and adsorption efficiency. The calculated adsorption energy using Monte Carlo-based simulation annealing method signified faster and higher adsorption of malachite green than methylene blue dye at surface-active sites (-COOH, CO, C-OH, and π-electron-rich domains) of SDAC adsorbent, corroborating the experimental results. The batch-mode adsorptive separation results showed remarkably high adsorption efficiency (>99%) for industrial wastewater to remove cationic and anionic dyes together. The SDAC displayed significantly high adsorption of methylene blue dye (625 mg.g^-1) with excellent recyclability without measurable loss of adsorption efficiency even after ten cycles. The SDAC fixed-bed column showed a dye removal capacity of 594 mg.g^-1 at 90% breakthrough in a continuous-mode process signifying its applicability for a real-time industrial run. The excellent conformity between batch mode and fixed bed continuous column adsorption data, along with higher removal capacity and remarkable recyclability, promise the use of SDAC adsorbent for industrial wastewater treatment to remove multiple organic pollutants.

Synthesis of mesoporous-structured MIL-68(Al)/MCM-41-NH2 for methyl orange adsorption: Optimization and Selectivity

Here, we report a novel amino-modified mesoporous-structured aluminum-based metal-organic framework adsorbent, MIL-68(Al)/MCM-41-NH₂, for dye sewage treatment. The introduction of molecular sieves overcomes the inherent defects of microporous MOFs in contaminant transfer and provides more active sites to enhance adsorption efficiency. Compared with using organic amino ligands directly, this strategy is ten times cheaper. The composite was well characterized and analyzed in terms of morphology, structure and chemical composition. Batch experiments were carried out to study the influences of essential factors on the process, such as pH and temperature. In addition, their interactions and the optimum conditions were examined using response surface methodology (RSM). The adsorption kinetics, isotherms and thermodynamics were systematically elucidated. In detail, the adsorption process conforms to pseudo-second-order kinetics and follows the Sips and Freundlich isothermal models. Moreover, the maximum adsorption capacity Q_s of methyl orange (MO) was 477 mg g^-1. It could be concluded that the process was spontaneous, exothermic, and entropy-reducing. Several binary dye systems have been designed for selective adsorption research. Our material has an affinity for anionic pigments. The adsorption mechanisms were discussed in depth. The electrostatic interaction might be the dominant effect. Meanwhile, hydrogen bonding, π-π stacking, and pore filling might be important driving forces. The excellent thermal stability and recyclability of the adsorbent are readily noticed. After five reuse cycles, the composite still possesses a removal efficiency of 90% for MO. Overall, the efficient and low-cost composite can be regarded as a promising adsorbent for the selective adsorption of anionic dyes from wastewater.

Green Preparation of Durian Rind-Based Cellulose Nanofiber and Its Application in Aerogel

In this study, a green, highly efficient and low energy consumption preparation method of cellulose nanofiber (CNF) was developed by using agricultural and forestry waste durian rinds as raw materials. The power of ultrasonic treatment was successfully reduced to only 360 W with low molecular weight liquid DMSO. The obtained durian rind-based CNF had a diameter of 8–20 nm and a length of several micrometers. It had good dispersion and stability in water, and could spontaneously cross-link to form hydrogel at room temperature when the concentration was more than 0.5%. The microscopic morphology and compressive properties of CNF aerogels and composite cellulose aerogels prepared from durian rind-based CNF were evaluated. It was found that CNF could effectively prevent the volume shrinkage of aerogel, and the concentration of CNF had a significant effect on the microstructure and mechanical properties of aerogel. The CNF aerogel with 1% CNF exhibited a sheet structure braced by fibers, which had the strongest compression performance. The porosity of CNF aerogels was high to 99%. The compressive strength of the composite cellulose aerogel with durian rind-based CNF was effectively enhanced.

Interfacial Imide Polymerization of Functionalized Filled Microcapsule Templates by the Pickering Emulsion Method for the Rapid Removal of 3,4,5-Trichlorophenol from Wastewater

In this work, an olive oil-filled composite capsule (C-O/W) adsorbent was prepared for the adsorption of 3,4,5-trichlorophenol (3,4,5-TCP) by the emulsion templating method. Using methylene diisocyanate (HDI) and 1,6-hexanediamine (HMDA) as functional monomers, olive oil was encapsulated in a shell layer composed of graphene oxide and a polymer by interfacial imine polymerization. The contaminant target was efficiently removed by the hydrophobic interaction between olive oil and chlorophenols. The removal of 3,4,5-TCP was remarkable, with an encapsulation rate of 85%. The unique microcapsule structure further enhanced the kinetic performance, which reached 92% of the maximum value within 40 min. The adsorption of different chlorophenols was investigated using 2-chlorophenol (2-CP), 2,6-dichlorophenol (2,6-DCP), and 3,4,5-TCP. The adsorption of 3,4,5-TCP by the C-O/W microcapsules was found to be much higher than that of other chlorophenols. When analyzing a real sample, the content of 3,4,5-TCP was significantly reduced after adsorption by the C-O/W microcapsules, demonstrating that the C-O/W microcapsules were also capable of removing 3,4,5-TCP from a complex environment. This simple and inexpensive preparation strategy provides a new method for the synthesis of functionalized C-O/W microcapsule adsorbents and an effective adsorbent of 3,4,5-TCP.

Recent advances in waste-derived functional materials for wastewater remediation

Water pollution is a major concern for public health and a sustainable future. It is urgent to purify wastewater with effective methods to ensure a clean water supply. Most wastewater remediation techniques rely heavily on functional materials, and cost-effective materials are thus highly favorable. Of great environmental and economic significance, developing waste-derived materials for wastewater remediation has undergone explosive growth recently. Herein, the applications of waste (e.g., biowastes, electronic wastes, and industrial wastes)-derived materials for wastewater purification are comprehensively reviewed. Sophisticated strategies for turning wastes into functional materials are firstly summarized, including pyrolysis and combustion, hydrothermal synthesis, sol-gel method, co-precipitation, and ball milling. Moreover, critical experimental parameters within different design strategies are discussed. Afterward, recent applications of waste-derived functional materials in adsorption, photocatalytic degradation, electrochemical treatment, and advanced oxidation processes (AOPs) are analyzed. We mainly focus on the development of efficient functional materials via regulating the internal and external characteristics of waste-derived materials, and the material's property-performance correlation is also emphasized. Finally, the key future perspectives in the field of waste-derived materials-driven water remediation are highlighted.

Ultralight, Mechanically Enhanced, and Thermally Improved Graphene-Cellulose-Polyethyleneimine Aerogels for the Adsorption of Anionic and Cationic Dyes

Graphene-cellulose-polyethyleneimine aerogels (GA-MCC-PEI) were prepared using a simple, environmentally friendly method to remove anionic and cationic dyes in water. Graphene-cellulose hydrogels were prepared using a hydrothermal method and then immersed in a polyethyleneimine aqueous solution for 48 h to obtain graphene-cellulose-polyethyleneimine hydrogels, which were then freeze-dried. The light and porous composite aerogels had a good compression resistance, and the maximum allowable pressure of the graphene-cellulose-polyethyleneimine aerogel with a cellulose content of 43% was 21.76 kPa, which was 827 times its weight. Adsorption of the anionic dye amaranth and the cationic dye methylene blue by the graphene-cellulose-polyethyleneimine aerogel was satisfactorily modeled using the Langmuir isothermal equation, indicating monolayer adsorption. When the cellulose content was 39%, the equilibrium adsorption capacities of the composite aerogel for amaranth and methylene blue were 369.37 mg/g and 237.33 mg/g, respectively. This graphene-cellulose-polyethyleneimine aerogel can be used to remove dye pollutants in water to maintain ecological balance, thus broadening the application space of aerogel materials, that is, as adsorbents in different environments.

Enhanced Sonocatalytic Performance of Non-Metal Graphitic Carbon Nitride (g-C3N4)/Coconut Shell Husk Derived-Carbon Composite

This study focused on the modification of graphitic carbon nitride (g-C3N4) using carbon which was obtained from the pyrolysis of coconut shell husk. The sonocatalytic performance of the synthesized samples was then studied through the degradation of malachite green. In this work, pure g-C3N4, pure carbon and carbon/g-C3N4 composites (C/g-C3N4) at different weight percentages were prepared and characterized by using XRD, SEM-EDX, FTIR, TGA and surface analysis. The effect of carbon amount in the C/g-C3N4 composites on the sonocatalytic performance was studied and 10 wt% C/g-C3N4 showed the best catalytic activity. The optimization study was conducted by using response surface methodology (RSM) with a central composite design (CCD) model. Three experimental parameters were selected in RSM including initial dye concentration (20 to 25 ppm), initial catalyst loading (0.3 to 0.5 g/L), and solution pH (4 to 8). The model obtained was found to be significant and reliable with R2 value (0.9862) close to unity. The degradation efficiency of malachite green was optimized at 97.11% under the conditions with initial dye concentration = 20 ppm, initial catalyst loading = 0.5 g/L, solution pH = 8 after 10 min. The reusability study revealed the high stability of 10 wt% C/g-C3N4 as sonocatalyst. In short, 10 wt% C/g-C3N4 has a high potential for industrial application since it is cost effective, reusable, sustainable, and provides good sonocatalytic performance.