Evaluation of the bond strength of chlorhexidine incorporated into the adhesive system composition: A PRISMA guided meta-analysis

Antibacterial Agents for Composite Resin Restorative Materials: Current Knowledge and Future Prospects

Resin composites became the material of choice for direct restorations in anterior and posterior teeth. Despite the revolutionary improvement in the material, restoration failure is still a major drawback due to the material's inherent negative properties, including a lack of antibacterial effects. Therefore, many attempts have been made to incorporate antibacterial agents into resin composite materials to improve their antimicrobial properties and prevent secondary caries formation. Multiple laboratory studies have been conducted using different antibacterial agents, such as quaternary ammonium compounds, methacryloyloxydodecylpyridinium bromide, magnesium oxide nanoparticles, chlorhexidine, and chitosan. This review provides a glance at the current status of these materials and the research directions needed in the future.

The effect of mechanical and chemo-mechanical temporary cement cleaning methods on shear bond strength with self-adhesive resin cement (an in-vitro study)

BACKGROUND

Adhesive tooth-colored restorations are strongly dependent on the substrate surface cleanliness to allow intimate contact between resin cement and dentin surface, so several methods were adopted for the total cleaning of temporary cement residues. This study aimed to assess the effect of mechanical and chemo-mechanical cleaning methods of temporary cement on the immediate shear bond strength of self-adhesive resin cement to dentin surface.

METHODS

Forty freshly extracted lower first premolars were cut to expose a flat dentin surface. Discs of temporary crown composite resin material were constructed and cemented to the flat dentin surface using resin-based and non-eugenol temporary cement then stored at room temperature in distilled water. Dividing of samples into two groups according to the method of temporary cement cleaning. Group I (n = 20) mechanical cleaning using the rotary instrument, and group II (n = 20) chemo-mechanical cleaning using chlorhexidine-containing scrub. CAD/CAM reinforced Composite discs were bonded to the dentin surface using self-adhesive composite resin cement, then measurement of shear bond strength was done using a universal testing machine. Further analysis of failure mode after debonding was performed by Scanning electron microscope.

RESULTS

No statistically significant difference was found between the mean shear bond strength of the two cleaning methods (P-value = 0.636). Regardless of the cleaning method, the group cemented with resin-based temporary cement showed statistically significantly higher mean shear bond strength than non-eugenol temporary cement (P-value = 0.048).

CONCLUSION

Both cleaning methods (mechanical and chemo-mechanical) applied in this study were effective in cleaning temporary cement remnants from the dentin substrate surface with statistically significant differences between results of shear bond strength with significantly higher values recorded with resin-based temporary cement.

Incorporation of MMP inhibitors into dental adhesive systems and bond strength of coronal composite restorations: A systematic review and meta-analysis of in vitro studies

Purpose

To systematically review in vitro studies that incorporated MMP inhibitors into adhesive systems in terms of the effect on immediate and aged bond strength of dental composite to dentine.

Materials and methods

Independently, two reviewers conducted an electronic search in three databases (MEDLINE, EMBASE, and Google Scholar) following the Preferred Reporting Items for Systematic Review and Meta-Analyses Protocols (PRISMA-P), up to 6 March 2022.

Results

The search resulted in 894 papers, 33 of which were eligible to be included in the review; of those, 13 fulfilled the meta-analysis eligibility criteria. Nineteen inhibitors were used among the studies, and those included in the meta-analysis were 2%, 0.2% chlorhexidine (CHX), 5 µM GM1489, and 0.5%, 1% benzalkonium chloride (BAC). In the meta-analysis, while above inhibitors showed no adverse effect on bond strength, 0.2% CHX and 5 µM GM1489 caused a significant increase in immediate and 12-months bond strength. All other inhibitors resulted in a significant increase in bond strength at six months of ageing.

Conclusions

Incorporation of MMP inhibitors into the adhesive system has no unfavourable effect on immediate bond strength but a favourable effect on longer-term bond strength. Additionally, inhibitors other than CHX could have similar or better effects on bond strength.

A meta-analysis of metal biosorption by suspended bacteria from three phyla

Biosorption of heavy metals by bacterial biomass has been the subject of significant research interest in last decades due to its efficiency, relatively low cost and minimal negative effects for the surrounding environment. In this meta-analysis, the biosorption efficiencies of different bacterial strains for Cu(II), Cd(II), Zn(II), Cr(III), Mn(II), Pb(II) and Ni(II) were evaluated. Optimum conditions for the biosorption process such as initial metal concentration, temperature, pH, contact time, metal type, biomass dosage and bacterial phyla, were evaluated for each heavy metal. According to the results, the efficiencies of bacterial biomass for removal of heavy metal were as follows: Cd(II) > Cr(III) > Pb(II) > Zn(II) > Cu(II) > Ni(II) > Mn(II). Firmicute phyla showed the highest overall (living and dead) biosorption efficiency for heavy metals. Living biomass of Proteobacteria had the best biosorption performance. Living bacterial biomass was significantly more efficient in biosorption of Cu(II), Zn(II) and Pb(II) than dead biomass. The maximum biosorption efficiency of bacterial strains for Cd(II), Pb(II) and Zn(II) was achieved at pH values between 6 and 7.5. High temperatures (>35 °C) reduced the removal efficiencies for Cu(II) and Zn(II) and increased the efficiencies for Cd(II) and Cr(III) ions. The maximum biosorption efficiency of non-essential heavy metals occurred with short contact times (<2 h). Essential metals such as Zn and Cu were more efficiently removed with long biosorption durations (>24 h). The mean biosorption capacity of bacterial biomass was between 71.26 and 125.88 mg g^-1. No publication bias existed according to Egger's and Begg's test results.

The effect of chlorhexidine primer application on the clinical performance of composite restorations: a literature review

To discuss the effectiveness of chlorhexidine (CHX) used as therapeutic dentin primer in adhesively bonded composite restorations. OVERVIEW: An electronic search in MEDLINE database, accessed through PubMed was conducted. No restrictions of languages and date of publication were made. The following key words were used: "chlorhexidine", "composite" and "composite resins." Clinical studies in which CHX was used during bonding procedures were included in this review. Six studies met the inclusion criteria. Of these, five studies were carried out on noncarious cervical lesions (NCCL). Only one study was carried out on class II preparation of permanent molars. In all studies, either etch-and-rinse and self-etch adhesive systems were used during bonding procedures. On the basis of the reviewed clinical trials, it can be concluded that CHX primer application does not seem to influence clinical outcome of composite restorations. CLINICAL SIGNIFICANCE: Current scientific evidence cannot neither strongly recommend nor discourage the application of CHX as therapeutic primer in composite restorations. Studies with longer follow-up periods with adhesive restorations placed on dentin after caries removal, rather than only on NCCL, are desirable to further investigate the therapeutic effect of CHX during bonding procedures.