A critical review on strategies for improving efficiency of BaTiO3-based photocatalysts for wastewater treatment

Ag-Incorporated Cr-Doped BaTiO3 Aerogel toward Enhanced Photocatalytic Degradation of Methyl Orange

A novel Cr-doped BaTiO3 aerogel was successfully synthesized using a co-gelation technique that involves two metallic alkoxides and a supercritical drying method. This freshly prepared aerogel has a high specific surface area of over 100 m2/g and exhibits improved responsiveness to the simulated sunlight spectrum. Methyl orange (MO) was chosen as the simulated pollutant, and the results reveal that the Cr-doped BaTiO3 aerogel, when modified with the noble metal silver (Ag), achieves a pollutant removal rate approximately 3.2 times higher than that of the commercially available P25, reaching up to 92% within 60 min. The excellent photocatalytic performance of the Ag-modified Cr-doped BaTiO3 aerogel can be primarily attributed to its extensive specific surface area and three-dimensional porous architecture. Furthermore, the incorporation of Ag nanoparticles effectively suppresses the recombination of photo-generated electrons and holes. Stability and reusability tests have confirmed the reliability of the Ag-modified Cr-doped BaTiO3 aerogel. Therefore, this material emerges as a highly promising candidate for the treatment of textile wastewater.

Advanced photocatalysis as a viable and sustainable wastewater treatment process: A comprehensive review

In our era, water pollution not only poses a serious threat to human, animal, and biotic life but also causes serious damage to infrastructure and the ecosystem. A set of physical, chemical, and biological technologies have been exploited to decontaminate and/or disinfect water pollutants, toxins, microbes, and contaminants, but none of these could be ranked as sustainable and scalable wastewater technology. The photocatalytic process can harmonize the sunlight to degrade certain toxins, chemicals, microbes, and antibiotics, present in water. For example, transition metal oxides (ZnO, SnO2, TiO2, etc.), when integrated into an organic framework of graphene or nitrides, can bring about more than 90% removal of dyes, microbial load, pesticides, and antibiotics. Similarly, a modified network of graphitic carbon nitride can completely decontaminate petrochemicals. The present review will primarily highlight the mechanistic aspects for the removal and/or degradation of highly concerned contaminants, factors affecting photocatalysis, engineering designs of photoreactors, and pros and cons of various wastewater treatment technologies already in practice. The photocatalytic reactor can be a more viable and sustainable wastewater treatment opportunity. We hope the researcher will find a handful of information regarding the advanced oxidation process accomplished via photocatalysis and the benefits associated with the photocatalytic-type degradation of water pollutants and contaminants.

Silver doped barium titanate nanoparticles for enhanced visible light photocatalytic degradation of dyes

Due to the rapid growth of global population, new, fast and reliable methods must be developed to purify contaminated water. Various photocatalysts have been developed to remove organic dyes from water. Herein, Ag doped BaTiO3 has been synthesized using a facile solvothermal method and its excellent photocatalytic activities were demonstrated in degradation of both anionic and cationic dyes under visible light illumination. Ag doped BaTiO3 nanoparticles showed greater efficacy in the degradation of methylene blue (MB) and eosin yellow (EY) than undoped BaTiO3 nanoparticles, which makes them a better candidate for photocatalysis. 1.0 AgBT sample showed the highest photocatalytic activity for MB (99.1 % in 100 min) and EY (99.3 % in 60 min) dye degradation compared with those of other samples. Further, the trapping experiments revealed that hydroxyl radicals and holes are the active species in the photocatalytic process of MB and EY dye degradation and recycle test showed excellent stability of the synthesized material.

Facile synthesis of a GO-g-C3N4/BaTiO3 ternary nanocomposites for visible-light-driven photocatalytic degradation of rhodamine B

Photogenerated charge carriers can undergo rapid recombination in conventional photocatalyst systems, reducing their photocatalytic efficiency. To address this bottleneck, a g-C3N4/BaTiO3 (CNB) heterojunction composite was decorated with different mass ratios of graphene oxide (GO) to form a novel visible-light responsive ternary GO-g-C3N4/BaTiO3 (GOCNB) nanocomposite using a facile fabrication method. The GOCNB photocatalyst exhibited significantly higher light absorption and greater charge transfer than CNB, g-C3N4, or BaTiO3. The photodegradation performance of GOCNB was optimized with a 2% mass loading of GO, and it achieved a degradation rate constant of 14.9 × 10-3 min-1 for rhodamine B with an efficiency of 94% within 180 min. The rate constant was 8-fold and 6-fold higher than that of bare BaTiO3 and CNB, respectively. The stronger photocatalytic activity was attributed to the synergistic effect of GO, g-C3N4, and BaTiO3, with g-C3N4 and BaTiO3 promoting charge transfer within a wider visible light range and GO promoting electron mobility and the photocatalyst's adsorption capacity. In particular, the proposed system maintained the spatial separation of photogenerated electron-hole pairs, which is vital for high photocatalytic activity. This study provides new insights into semiconductor-based photocatalytic systems and suggests a route for more environmentally sustainable technologies.

CO to formaldehyde transformation study on pristine and Au-modified BaTiO3(001) through DFT calculations

CONTEXT

BaTiO3 is one of the most important ferroelectric oxides in electronic applications. Also, it has attractive properties for catalysis that could be used for reducing contamination levels, especially carbon monoxide, CO. CO is one of the main gaseous pollutants generally released from the combustion of fossil fuel. In this work, the CO transformation on pristine and Au-modified BaTiO3 perovskite for H2CO obtention is studied. The CO adsorption and hydrogenation on pristine BaTiO3 leads to formaldehyde synthesis as the most stable product through two possible routes. Furthermore, hydrogenation stages are less probable on pristine BaTiO3. On Au-modified BaTiO3 formaldehyde is the principal product too but Au adatom generates H2CO competition with HCOH. After BaTiO3 modification with Au unpaired electrons were generated. These unpaired electrons are related to the adatom reactivity. According to the obtained results, pristine and Au-modified BaTiO3 can adsorb and hydrogenate CO generating formaldehyde as the principal product. BaTiO3 modifications with Au increase the reactivity of the perovskite in the CO hydrogenation reactions. CO hydrogenation process on Au suggests that further hydrogenation stages beyond formaldehyde are possible.

METHODS

The study was performed through ab initio calculations using the periodic spin-polarized Density Functional Theory (DFT) as implemented in Quantum ESPRESSO. DFT calculations were carried out using the Plane Wave self-consistent field (PWscf). Spin density difference allows us to identify reactive regions related to dangling bonds and unpaired electrons. A plane wave basis set was used to represent the electron states. Vanderbilt pseudopotentials with nonlinear core correction were used to model the ionic cores and valence electrons interaction. Exchange-correlation energies were treated within the generalized gradient approximation (GGA) with the Perdew-Burke-Ernzerhof (PBE) parameterization.

Piezo-photocatalytic properties of BaTiO3/CeO2 nanoparticles with heterogeneous structure synthesized by a gel-assisted hydrothermal method

BaTiO3/CeO2 nanoparticles with heterogeneous structure were successfully synthesized via a gel-assisted hydrothermal method. The molar ratio of Ti/Ce was set as 1 : 0, 0.925 : 0.075, 0.9 : 0.1; 0.875 : 0.125, and 0.85 : 0.15 in the dried gels. Affected by the values of Ti/Ce, the particle sizes of hydrothermal products decreased obviously, and the surface of nanoparticles became rough and even had small protrusions. XRD, SEM, HRTEM, XPS, DRS, ESR, and PFM were used to characterize the nanoparticle textures. We speculated that the main body and surface of nanoparticles were BaTiO3 and CeO2 protrusions, respectively. The catalytic performance of BaTiO3/CeO2 nanoparticles was characterized by their abilities to degrade RhB in water under different external conditions (light irradiation, ultrasonic oscillation, or both). In all test groups, BaTiO3/CeO2 nanoparticles with a Ti/Ce molar ratio of 0.875 : 0.125 in the initial dried gel exhibited the strongest catalytic ability when light irradiation and ultrasonication were applied simultaneously owing to the appropriate amount of Ce3+ and oxygen vacancies.

A Breakthrough in Photocatalytic Wastewater Treatment: The Incredible Potential of g-C3N4/Titanate Perovskite-Based Nanocomposites

Water pollution has emerged as a major global environmental crisis due to the massive contamination of water resources by the textile dyeing industry, organic waste, and agricultural residue. Since water is fundamental to life, this grave disregard puts lives at risk, making the protection of water resources a serious issue today. Recent research has shown great interest in improving the photocatalytic performance of graphitic carbon nitride (g-C3N4) for wastewater treatment. However, the photocatalytic removal activity of pure g-C3N4 is poor, owing to its minimal surface area, fast recombination of photo-generated electron-hole pairs, and poor light absorption. Recently, titanate perovskites (TNPs) have attracted significant attention in both environmental remediation and energy conversion due to their exceptional structural, optical, physiochemical, electrical, and thermal properties. Accordingly, TNPs can initiate a variety of surface catalytic reactions and are regarded as an emerging category of photocatalysts for sustainability and energy-related industries when exposed to illumination. Therefore, in this review article, we critically discuss the recent developments of extensively developed g-C3N4/TNPs that demonstrate photocatalytic applications for wastewater treatment. The different synthetic approaches and the chemical composition of g-C3N4/TNP composites are presented. Additionally, this review highlights the global research trends related to these materials. Furthermore, this review provides insight into the various photocatalytic mechanisms, including their potential impact and significance. Also, the challenges faced by such materials and their future scope are discussed.

Optical investigation and computational modelling of BaTiO3 for optoelectronic devices applications

ABX₃ perovskite-based materials have attracted research attention in various electronic and optoelectronic applications. The ability to tune the energy band gap through various dopants makes perovskites a potential candidate in many implementations. Among various perovskite materials, BaTiO₃ has shown great applicability as a robust UV absorber with an energy band gap of around 3.2 eV. Herein, we provide a new sonochemical-assisted solid-phase method for preparing BaTiO₃ thin films that optoelectronic devices can typically be used. BaTiO₃ nano-powder and the thin film deposited on a glass substrate were characterized using physicochemical and optical techniques. In addition, the work demonstrated a computational attempt to optically model the BaTiO₃ from the atomistic level using density functional theory to the thin film level using finite difference time domain Maxwell's equation solver. Seeking repeatability, the dispersion and the extinction behavior of the BaTiO₃ thin film have been modeled using Lorentz-Dude (LD) coefficients, where all fitting parameters are listed. A numerical model has been experimentally verified using the experimental UV-Vis spectrometer measurements, recording an average root-mean-square error of 1.44%.

Bioenergy Generation and Wastewater Purification with Li0.95Ta0.76Nb0.19Mg0.15O3 as New Air-Photocathode for MFCs

MFC is a promising technology that can be used for simultaneous electricity generation and wastewater treatment. Power energy generation of a ferroelectric cathodic ceramic, Li0.95Ta0.76Nb0.19Mg0.15O3 (LTNMg), has been measured in microbial fuel cells, integrating a single chamber fed by industrial wastewater (CODinitial = 471 mg L−1, and pHinitial = 7.24 at T = 27 °C). In this process, the mixed multicomponent oxide material has been prepared and characterized by XRD, PSD, TEM, and UV-Vis spectroscopy. The catalytic activity has been investigated by COD determination, analysis of heavy metals, and polarization measurement. The results show a high COD reduction efficiency, which reaches 95.70% after a working time of 168 h with a maximal power density of 228 mW m−2. In addition, the maximum value of generated voltage in the open-circuit potential (OCP) of this MFC configuration has been increased from 340 mV in the absence of a light source to 470 mV under irradiation, indicating the presence of a promoting photocatalytic effect of LTNMg, which improved the process of the cathodic electron transfer inside the MFC device.

Insights into photocatalytic degradation of phthalate esters over MSnO3 perovskites (M = Mg, Ca): Experiments and density functional theory

In this study, the physicochemical and photocatalytic properties of two kinds of stannate perovskite oxides (MgSnO₃ and CaSnO₃) were investigated under simulated sunlight, where dimethyl phthalate (DMP) and diethyl phthalate (DEP) were selected as the probe pollutants. The results of photochemical characterization showed that MgSnO₃ perovskite exhibited better photocatalytic performance than CaSnO₃ perovskite. MgSnO₃ perovskite could effectively degrade 75% of DMP and 79% of DEP through pseudo-first-order reaction kinetics, which remained good in pH 3.0 to 9.0. Quenching experiments and electron paramagnetic resonance (EPR) characterization indicated that photogenerated holes (h⁺), superoxide (O₂^-), and hydroxyl radicals (OH) worked in the photo-degradation, while O₂^- played the most important role. Furthermore, intermediates identification and density functional theory (DFT) calculations were used to explore the degradation mechanism. For both DMP and DEP, the reactive oxygen species (ROS, including O₂^- and OH) were responsible for the hydroxylation of benzene ring and the breaking of the aliphatic chain, while h⁺ was prone to break the aliphatic chain. This work is expected to provide new insights on the photocatalytic mechanism of stannate perovskites for environmental remediation.

Effects of particle size and polymorph type of TiO2 on the properties of BaTiO3 nanopowder prepared by solid-state reaction

Barium titanate (BaTiO₃) has attracted considerable attention as a perovskite ferroelectric ceramic material for electronic multilayer ceramic capacitors (MLCCs). Fine BaTiO₃ nanopowders with a considerably high tetragonality directly influence the typical properties of nanopowders; however, their synthesis has remained challenging. In this study, we analyzed the effect of two different TiO₂ powders with anatase and rutile phases in a solid-state reaction with barium carbonate (BaCO₃). The effect of the particle size ratio (TiO₂/BaCO₃) of the raw materials on the tetragonality and particle size of the as-synthesized BaTiO₃ powders was also determined through extensive characterization of the powders by X-ray diffraction, field-emission scanning electron microscopy, and Raman spectroscopy. The present investigation reveals that the design BaTiO₃ structure is expected to advance the development of efficient catalytic and sensor materials for sustainable environmental applications.