Selective adsorption of heavy metals from water by a hyper-branched magnetic composite material: Characterization, performance, and mechanism

Molecular level decontamination of trace quinolones and Serratia marcescens in wastewater via in situ Cu(III) complexes mediated Fenton-like oxidation

Co-pollution caused by antibiotics and antibiotic-resistant bacteria (ARB) in wastewater has led to widespread concerns. Hence, their targeted and synergistic decontamination is urgently required. A homogeneous Fenton-like oxidation system comprising cupric complexes-activated peroxymonosulfate (PMS) was demonstrated to synergistically decontaminate trace quinolones (QNs) and QNs-resistant Serratia marcescens (QRSM) in wastewater. More than 99 % of QNs were degraded within 60 min under alkaline condition, and the degradation efficiency was only slightly influenced by humic acid (up to 1 %) and various anions (up to 20 %), furthermore, the degraded pathway was proposed and the environmental risk after QNs degradation were also reduced. The activation of PMS via cupric complexes coupling in situ Cu(III) complexes generation promoted intramolecular electron transfer (IET) featuring the targeted oxidation of QNs. The produced Cu(III) and •OH played primary and secondary roles in the synergistic inactivation of QRSM by destroying the cell membranes and walls, DNA bases (T, A, C, and G), antibiotic resistance genes (ARGs, including intracellular ARGs and extracellular ARGs), and total DNA (including intracellular DNA and extracellular DNA). This study demonstrates a successful strategy and provides an innovative perspective for the molecular level decontamination of trace antibiotics and ARB using a homogeneous cupric complexes-activated Fenton-like oxidation system from metal ions inherent in breeding wastewater under alkaline condition.

Remarkable purification of organic dyes by NiOOH-modified industrial waste residues

Extracting functional materials from industrial waste residues to absorb organic dyes can maximize waste reuse and minimize water pollution. However, the extraordinarily low purification efficiency still limits the practical application of this strategy. Herein, the lamellar NiOOH is in-situ anchored on the industrial waste red mud surface (ARM/NiOOH) as an adsorbent to purify organic dyes in wastewater. ARM/NiOOH adsorbent with high specific surface area and porosity provides considerable active sites for the congo red (CR), thereby significantly enhancing the removal efficiency of CR. Besides, we fit a reasonable adsorption model for ARM/NiOOH adsorbent and investigate its adsorption kinetics. Resultantly, ARM/NiOOH adsorbent can remarkably adsorb 348.0 mg g-1 CR within 5 min, which is 7.91 times that of raw RM. Our work provides a strategy for reusing industrial waste and purifying sewage pollution, which advances wastewater treatment engineering.

Sustainable Zn2+ removal using highly efficient, novel, and cost-effective chitosan-magnetic biochar composite

This study focused on the development of a sustainable and low-cost adsorbent derived from the chitosan-biochar composite for the removal of Zn2+ from an aqueous solution. Biochar was prepared from cotton stalk residue by pyrolysis at 600 °C for 2 h, modified with FeCl3, and composed with chitosan in various ratios (1:3, 1:1, 3:1), leading to the formation of an efficient, thermally stable, and rich with functional groups chitosan-biochar composite denoted as CHB-Fe-CS. Functional groups (hydroxyl, carboxyl, and amine) were identified as key contributors to the adsorption mechanism. Langmuir isotherm (R2 = 0.99) and Pseudo-Second order (R2 = 0.99) were best fitted models with the experimental results indicating chemisorption-driven monolayer adsorption. The results revealed CHB-Fe-CS (3:1) composite obtained the highest adsorption capacity of 117.50 mg/g for Zn2+ under optimal conditions viz., 180 min batch time, 500 mg/l metal concentration, 4 g/l adsorbent dosage, 40 °C solution temperature, and 5.0 pH. Regeneration of the used adsorbent was performed using 0.2 mol/l HCl and obtained desorption efficiency of 67.48% and 51.48% after the 4th and 8th cycles. The adsorption mechanisms were dominated by ion exchange, surface complexation, and electrostatic attraction compared to intra-particle diffusion and physisorption. The CHB-Fe-CS demonstrated an economical, environment friendly, and good performing adsorbent for water decontamination.

Synthesis of Aminomethylpyridine-Decorated Polyamidoamine Dendrimer/Apple Residue for the Efficient Capture of Cd(II)

Water contamination irritated by Cd(II) brings about severe damage to the ecosystem and to human health. The decontamination of Cd(II) by the adsorption method is a promising technology. Here, we construct aminomethylpyridine-functionalized polyamidoamine (PAMAM) dendrimer/apple residue biosorbents (AP-G1.0-AMP and AP-G2.0-AMP) for adsorbing Cd(II) from aqueous solution. The adsorption behaviors of the biosorbents for Cd(II) were comprehensively evaluated. The maximum adsorption capacities of AP-G1.0-AMP and AP-G2.0-AMP for Cd(II) are 1.40 and 1.44 mmol·g-1 at pH 6. The adsorption process for Cd(II) is swift and can reach equilibrium after 120 min. The film diffusion process dominates the adsorption kinetics, and a pseudo-second-order model is appropriate to depict this process. The uptake of Cd(II) can be promoted by increasing concentration and temperature. The adsorption isotherm follows the Langmuir model with a chemisorption mechanism. The biosorbents also display satisfied adsorption for Cd(II) in real aqueous media. The adsorption mechanism indicates that C-N, N═C, C-O, CONH, N-H, and O-H groups participate in the adsorption for Cd(II). The biosorbents display a good regeneration property and can be reused with practical value. The as-prepared biosorbents show great potential for removing Cd(II) from water solutions with remarkable significance.

Alginate Modified Magnetic Polypyrrole Nanocomposite for the Adsorptive Removal of Heavy Metal

The presence of heavy metals with high acute toxicity in wastewater poses a substantial risk to both the environment and human health. To address this issue, we developed a nanocomposite of alginate-encapsulated polypyrrole (PPy) decorated with α-Fe2O3 nanoparticles (Alg@Mag/PPy NCs), fabricated for the removal of mercury(II) from synthetic wastewater. In the adsorption experiments, various parameters were examined to identify the ideal conditions. These parameters included temperature (ranging from 298 to 323 K), initial pH levels (ranging from two to nine), interaction time, amount of adsorbent (from 8 to 80 mg/40 mL), and initial concentrations (from 10 to 200 mg/L). The results of these studies demonstrated that the removal efficiency of mercury(II) was obtained to be 95.58% at the optimum pH of 7 and a temperature of 303 K. The analysis of adsorption kinetics demonstrated that the removal of mercury(II) adhered closely to the pseudo-second-order model. Additionally, it displayed a three-stage intraparticle diffusion model throughout the entire adsorption process. The Langmuir model most accurately represented equilibrium data. The Alg@Mag/PPy NCs exhibited an estimated maximum adsorption capacity of 213.72 mg/g at 303 K, surpassing the capacities of most of the other polymer-based adsorbents previously reported. The thermodynamic analysis indicates that the removal of mercury(II) from the Alg@Mag/PPy NCs was endothermic and spontaneous in nature. In summary, this study suggests that Alg@Mag/PPy NCs could serve as a promising choice for confiscating toxic heavy metal ions from wastewater through adsorption.

Removal of Phosphate by Adsorption with 2-Phenylimidazole-Modified Porous ZIF-8: Powder and Chitosan Spheres

Due to rapid socioeconomic development, increased phosphorus concentrations can cause eutrophication of water bodies, with devastating effects on environmental sustainability and aquatic ecosystems. In this study, ZIF-8-PhIm was prepared for phosphorus removal using 2-phenylimidazole via the solvent-assisted ligand exchange (SALE) method. The structure and composition of ZIF-8-PhIm were characterized by various methods, including X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), 1H nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), and Brunauer-Emmett-Teller (BET) analysis. Compared to the ZIF-8 material, it exhibited a multistage pore structure with larger pore capacity and pore size, increased hydrophilicity, exposure of more adsorption sites, and also stronger electrostatic interaction. Under optimized conditions (T = 298 K, C0 = 150 mg/L, dose = 0.2 g/L), the adsorption capacity of ZIF-8-PhIm reached 162.93 mg/g, which was greater than that of the ZIF-8 material (92.07 mg/g). The Langmuir isotherm and pseudo-second-order kinetic models were suitable for describing the phosphate adsorption of ZIF-8-PhIm. The main effects of ZIF-8-PhIm on phosphate adsorption were Zn-O-P bonding and electrostatic interactions. It also had good regeneration properties. The ZIF-8-PhIm/CS spheres were prepared using chitosan (CS) as the cross-linking agent. The results of dynamic adsorption experiments on the spheres showed a saturation capacity of 85.69 mg/g and a half-penetration time of 514.15 min at 318 K according to the fitted results.

A strategy-purifying wastewater with waste materials: Zn2+ modified waste red mud as recoverable adsorbents with an enhanced removal capacity of congo red

The strategy, called purifying wastewater with waste materials (PWWM), can simultaneously improve the secondary utilization of industrial waste materials and in turn, reduce environmental pollution. However, the PWWM strategy has still not been extensively used because of its low purification efficiency of organic pollutants and extremely difficult secondary utilization process. Herein, we use zinc aluminum silicate (ZAS) to modify waste granular red mud (GRM) to form a recoverable adsorbent, called ZAS/GRM adsorbent. The ZAS has been found to exhibit exceptional adsorption performance with the ability to firmly anchor onto the surface of GRM, in which heavy metal ions can effectively solidify and reduce their outflow. Furthermore, many voids have been tactfully designed in the ZAS/GRM adsorbents by using a water vapor project, which provide more active sites for congo red (CR) organic dye, thereby remarkably improving the removal efficiency of CR. From our purification of CR, we find that the CR adsorption capacity of the ZAS/GRM adsorbent is 3.509 mg g^-1, which is four times higher than pure GRM (0.820 mg g^-1). This study demonstrates our PWWM strategy is highly effective and can inspire more research on waste reuse.

Synthesis of functional poly(amidoamine) dendrimer decorated apple residue cellulose for efficient removal of aqueous Hg(II)

Water pollution caused by Hg(II) exerts hazardous effect to the environment and public health. The design and fabrication of eco-friendly bioadsorbents for efficient removal of Hg(II) from aqueous solution is a promising strategy. Herein, a series of bioadsorbents were synthesized by the decoration of apple residue cellulose with different generation (G) Schiff base functionalized poly(amidoamine) (PAMAM) dendrimers (SA-G0/CE, SA-G1.0/CE and SA-G2.0/CE). The structures of SA-G0/CE, SA-G1.0/CE and SA-G2.0/CE were characterized and their adsorption performances were determined comprehensively by considering various factors. The maximum adsorption capacity of SA-G0/CE, SA-G1.0/CE and SA-G2.0/CE for Hg(II) are 1.18, 1.73 and 1.88 mmol·g^-1, respectively. The as-prepared bioadsorbents exhibit competitive adsorption capacity as compared with other reported adsorbents. Moreover, they exhibit remarkable adsorption selectivity toward Hg(II) with the coexistence of Ni(II), Cd(II), Mn(II), or Pb(II). The bioadsorbents display satisfactory adsorption performance in real water sample and can be reused with good regeneration property. Adsorption mechanism reveals that the functional groups of OH, -CONH-, CN and NC take part in the adsorption for Hg(II). The work not only opens a pathway to realize the reuse of apple residue, but also provides a promising strategy to construct efficient bioadsorbents for the decontamination of Hg(II) from aqueous solution.

Simultaneous removal of aqueous same ionic type heavy metals and dyes by a magnetic chitosan/polyethyleneimine embedded hydrophobic sodium alginate composite: Performance, interaction and mechanism

Heavy metals and azo dyes caused huge harm to the aqueous system and human health. A magnetic chitosan/polyethyleneimine embedded hydrophobic sodium alginate composite (MCPS) was designed and prepared to simultaneously remove aqueous same ionic type heavy metals and azo dyes. In mono-polluted system, the optimal pH for Cr(VI), MO (methyl orange), Cu(Ⅱ) and MB (methylene blue) were 3, 2, 6 and 12 with a saturated adsorption capacity of 87.53, 66.41, 351.03 and 286.54 mg/g, respectively. Pseudo-second-order was suitable to describe the adsorption kinetics of them and the adsorption isotherms were more consistent with the Langmuir isotherm model being a spontaneous, endothermic, and entropy-increasing process. In binary-polluted system, MCPS possessed simultaneous adsorption for Cr (Ⅵ)-MO and Cu(Ⅱ)-MB pollutants at their optimal pH, in addition, whether in anionic or cationic solution, the removal of heavy metals were promoted with the add of azo dyes but the removal of azo dyes were suppressed with the add of heavy metals. Both Cr (Ⅵ)-MO and Cu(Ⅱ)-MB pollutants could be effectively adsorbed and desorbed from MCPS by changing the pH of the aqueous solution to realize recyclability. Lastly, removal mechanism was revealed in detail by FT-IR, EDS and XPS.

Biosorption of zinc (II) from synthetic wastewater by using Inula Viscosa leaves as a low-cost biosorbent: Experimental and molecular modeling studies

The use of biosorption as a strategy for lowering the amount of pollution caused by heavy metals is particularly encouraging. In this investigation, a low-cost and efficient biosorbent, Inula Viscosa leaves were used to remove zinc ions (Zn²⁺) from synthetic wastewater. A Fourier transform infrared spectroscopy experiment, a scanning electron microscopy experiment, and an energy dispersive X-ray spectroscopy experiment were used to describe the support. Several different physicochemical factors, such as the beginning pH value, contact duration, initial zinc concentration, biosorbent dose, and temperature, were investigated in this study. When the Langmuir, Freundlich, Temkin, Toth, and Redlich-Peterson models were used to match the data from the Inula Viscosa leaves biosorption isotherms, it was found that the biosorption isotherms correspond most closely with the Langmuir isotherm. On the other hand, the kinetic biosorption process was investigated using pseudo-first-order, pseudo-second-order (PS2), and Elovich models. The PS2 model was the one that provided the most accurate description of the biosorption kinetics. The thermodynamics process shows the spontaneous and endothermic character of Zn²⁺ sorption on Inula Viscosa leaves, which also entails the participation of physical interactions. In addition, the atom-in-molecule analysis, density functional theory, and the conductor like screening model for real solvents, were used to investigate the relationship that exists between quantum calculations and experimental outcomes.

Regeneration mechanism of a novel high-performance biochar mercury adsorbent directionally modified by multimetal multilayer loading

Biochar that is directly obtained by pyrolysis exhibits a low adsorption efficiency; furthermore, the process of recycling adsorbents is ineffective. To solve these problems, conventional chemical coprecipitation, sol-gel, multimetal multilayer loading and biomass pyrolysis coking processes have been integrated. After selecting specific components for structural design, a novel high-performance biochar adsorbent was obtained. The effects of the O₂ concentration and temperature on the regeneration characteristics were explored. An isothermal regeneration method to repair the deactivated adsorbent in a specific atmosphere was proposed, and the optimal regeneration mode and conditions were determined. The microscopic characteristics of the regenerated samples were revealed along with the mechanism of Hg⁰ removal and regeneration by using temperature-programmed desorption technology and adsorption kinetics. The results show that doping multiple metals can reduce the pyrolysis reaction barrier of the modified biomass. On the modified surface of the sample, the doped metals formed aggregated oxides, and the resulting synergistic effect enhanced the oxidative activity of the biochar carriers and the threshold effect of Ce oxide. The optimal regeneration conditions (5% O₂ and 600 °C) effectively coordinated the competitive relationship between the deep carbonization process and the adsorption/oxidation site repair process; in addition, these conditions provided outstanding structure-effect connections between the physico-chemical properties and Hg⁰ removal efficiency of the regenerated samples. Hg⁰ adsorption by the regenerated samples is a multilayer mass transfer process that involves the coupling of physical and chemical effects, and the surface adsorption sites play a leading role.

Selective removal of aqueous Hg2+ by magnetic composites sulfur-containing on the hyper-branched surface: Characterization, performance and mechanism

The adsorbents with recyclable, large adsorption capacity and selective adsorption can effectively remove the pollution and harm of heavy metal ions in water. Therefore, two magnetic composites containing sulfur (MCP-S4 and MCP-S8) on the hyper-branched surface were prepared, furthermore, their structures were characterized and adsorption performance was analyzed by FTIR, XRD, TGA, BET, SEM, TEM, VSM and ICP. The results showed that both MCP-S4 and MCP-S8 had superparamagnetism with saturation susceptibility of 22.10 and 22.26 emu/g, and owned a specific surface area of 11.394 and 11.235 m²/g, respectively. MCP-S4 and MCP-S8 could selectively adsorb Hg²⁺ with the exist of Fe³⁺, Cu²⁺, Co²⁺, Ni²⁺, Mn²⁺, and Al³⁺ in solution. The adsorption kinetics accorded with pseudo-second-order model and Boyd film diffusion model, and the adsorption isotherm was fitted better with Langmuir isotherm model and D-R model, furthermore, the adsorption was an entropic-increasing and endothermic process. The removal rate of Hg²⁺ from simulated sewage by the two materials was more than 91%, and the adsorption retention rate was more than 85% after five adsorption-desorption cycles. The adsorption mechanism was analyzed by comparing the changes of FTIR, EDS and XPS spectra before and after adsorption. It was found that functional groups (C-N, CONH, CS, SH) could form stable chelates with Hg²⁺, which was the main reason why MCP-S4 and MCP-S8 could adsorb Hg²⁺ selectively, furthermore, S atoms of CS and -SH played a leading role in the process of adsorption. In addition, DFT calculation was also used as an auxiliary means to verify the adsorption mechanism.

Effects of synthesis temperature on ε-MnO2 microstructures and performance: Selective adsorption of heavy metals and the mechanism onto (100) facet compared with (001)

The heavy-metal adsorbent ε-MnO₂ was produced through a simple, one-step oxidation-reduction reaction at three different synthesis temperatures (25 °C, 50 °C and 75 °C) and their morphology and chemical-physical properties were compared. Of the three materials, MnO₂-25 had the largest specific surface area and the highest surface hydroxyl concentration. Its optimal performance was demonstrated by batch adsorption experiments with Pb²⁺, Cd²⁺ and Cu²⁺. Of the three metals, Pb²⁺ was adsorbed best (339.15 mg/g), followed by Cd²⁺ (107.50 mg/g) and Cu²⁺ (86.30 mg/g). When all three metals were present, Pb²⁺ was still absorbed best but now more Cu²⁺ was adsorbed than Cd²⁺. In order to explore the mechanism for the inconsistent adsorption order of Cd²⁺ and Cu²⁺ in single and competitive adsorption, we combined experimental data with density functional theory (DFT) calculations to elucidate the distinct adsorption nature of MnO₂-25 towards these three metals. This revealed that the adsorption affinity of the (100) facet was superior to (001), and since the surface complexes were also more stable on (100), this facet was most likely determining the adsorption order for the single metals. When the metals were present in combination, Pb²⁺ preferentially occupied the active adsorption sites of (100), forcing Cu²⁺ to be adsorbed on the (001) facet where Cd²⁺ was only poorly bound. Thus, the adsorption behavior was affected by MnO₂-25 surface chemistry at a molecular scale. This study provides an in-depth understanding of the adsorption mechanisms of the heavy metals on this adsorbent and offers theoretical guidance for production of adsorbent with improved removal efficiency.

Simultaneous removal of lead, manganese, and copper released from the copper tailings by a novel magnetic modified biosorbent

Potentially toxic elements including lead (Pb), manganese (Mn), and copper (Cu) released from copper tailings would cause severe long-term environmental risks and potential threats to human health. To prevent these negative effects caused by the release of the metals, a novel magnetic carboxyl groups modified bagasse with high adsorption affinity and strong magnetism was synthesized through an in-situ precipitation method and used to simultaneously remove Pb, Mn, and Cu from the eluate of copper tailings. Results showed that release of Pb, Mn, and Cu from the copper tailings was pH, time, and particle size dependent, and maximum concentrations of them released in the eluate was 1.7, 1.9, and 4.1 mg L^-1 under weak acid conditions. Batch adsorption experiment showed that the as-synthesized magnetic modified bagasse could selectively absorb Pb, Mn, and Cu from a complex solution with adsorption capacity of 137.3, 13.1, and 90.0 mg g^-1, respectively. X-ray photoelectron spectroscopy (XPS) and energy dispersive spectroscopy-mapping (EDS-mapping) demonstrated that Pb, Mn, and Cu interacted with the magnetic modified biosorbent mainly through coordination and ion exchange. Column experiments showed that higher than 99.5% of the released Pb, Mn, and Cu could be simultaneously removed by the magnetic modified bagasse, and the maximum concentrations of them released in the eluate of the copper tailings were all decreased to lower than 0.01 mg L^-1, which reached the discharge standards. After recycled by a magnet, the magnetic modified bagasse could be collected easily and used repeatedly. Because of the high efficiency and easy recovery, the used method had great practical application value in removal of potentially toxic elements released from metallic tailings.

Removal of p-nitrophenol from simulated sewage using MgCo-3D hydrotalcite nanospheres: capability and mechanism

4-Nitrophenol (4-NP) is an organic pollutant found in the wastewater discharged from coking and petrochemical industries, and it is highly toxic, persistent, and bioaccumulative. 4-NP is difficult to degrade and causes serious damage to human health and the ecological environment. In this study, MgCo-3D hydrotalcite nanospheres were synthesized via the hot solvent method using ZIF-67 as a template for 4-NP removal from wastewater. The composition and structure of MgCo-3D hydrotalcite nanospheres were characterized via X-ray diffraction (XRD), Scanning electron microscope (SEM), Transmission Electron Microscope (TEM), Fourier-transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), Energy Dispersive Spectroscopy (EDS), and BET analyses. The maximum adsorption capacity was 131.59 mg g-1 under the optimized conditions (pH = 7, t = 298 K, C 0 = 50 mg L-1, dose = 0.4 g L-1). The adsorption obeyed the Langmuir, Redlich-Peterson and Sips models and pseudo-second-order kinetics, and the adsorption activation energy was 29.4 kJ mol-1, indicating a monolayer physical adsorption phenomenon. The adsorption of 4-NP on the MgCo-3D hydrotalcite nanospheres mainly involved hydrogen bonding and electrostatic interactions. The nanospheres were regenerated using the hot-air purging method. After five adsorption-desorption cycles, the adsorption capacity reached 107.6 mg g-1, indicating the good regeneration performance of the MgCo-3D hydrotalcite nanospheres.

Simultaneous Removal of Heavy Metals (Cu, Cd, Cr, Ni, Zn and Pb) from Aqueous Solutions Using Thermally Treated Romanian Zeolitic Volcanic Tuff

Increased concentrations of heavy metals in the environment are of public health concern, their removal from waters receiving considerable interest. The aim of this paper was to study the simultaneous adsorption of heavy metals (Cu, Cd, Cr, Ni, Zn and Pb) from aqueous solutions using the zeolitic volcanic tuffs as adsorbents. The effect of thermal treatment temperature, particle size and initial metal concentrations on the metal ions sorption was investigated. The selectivity of used zeolite for the adsorption of studied heavy metals followed the order: Pb > Cr > Cu > Zn > Cd > Ni. The removal efficiency of the heavy metals was strongly influenced by the particle sizes, the samples with smaller particle size (0−0.05 mm) being more efficient in heavy metals removal than those with larger particle size (1−3 mm). Generally, no relevant changes were observed in heavy metals removal efficiency for the treatment temperatures of 200 °C and 350 °C. Moreover, at a higher temperature (550 °C), a decrease in the removal efficiencies was observed. The Cd, Zn, Cu, Cr, Zn and Ni sorption was best described by Langmuir model according to the high values of correlation coefficient. The pseudo-first-order kinetic model presented the best correlation of the experimental data.