Underwater suspended bifunctionalized polyethyleneimine-based sponge for selective removal of anionic pollutants from aqueous solution

Interactions Between Polyethyleneimine Xerogels and Acetic Acid Vapor from Degraded Cellulose Acetate. A Novel Therapy for Motion Picture Films Affected by the "Vinegar Syndrome"

Motion picture films made of cellulose acetate (CA) are subjected to degradation mainly due to the "vinegar syndrome". The goal of this study is to investigate the absorption of acetic acid vapor by some polyethyleneimine (PEI) xerogels, aim at developing innovative, inexpensive, reusable, and easy-to-produce and handle chemical inhibitors for the "vinegar syndrome". PEI-based xerogels (SPEI) are obtained through cryo-polymerization via epoxy-amine reaction between PEI and 1,4-Butanediol di-glycidyl ether (BDDE). The intent is to enhance the absorption of the acetic acid vapor by the porous and high-specific surface area network of the obtained PEI xerogel, allowing its neutralization through the free amino groups present in the gel. A chemical-physical, morphological, and rheological characterization of the SPEIs is performed and their behavior in the absorption and desorption of acetic acid is also studied. The efficacy of the SPEI in inhibiting the "vinegar syndrome" is evaluated on both CA-based real motion picture films, on which the deacetylation process is artificially and naturally induced. The characterization of degraded CA films stored with and without the inhibitor is evaluated using an already validated multi-analytical protocol. The excellent results achieved open interesting perspectives for the conservation of these 20th-century cultural heritage objects.

Effective removal of Congo red and hexavalent chromium from aqueous solutions by guar gum/sodium alginate/Mg/Al-layered double hydroxide composite microspheres

In this paper, Mg/Al-layered double hydroxide (Mg/Al-LDH) was modified with the natural polymers sodium alginate and guar gum, and the prepared GG/SA/Mg-Al-LDH composite microsphere adsorbent (G-LDH) showed better adsorption performance for Congo red and hexavalent chromium in aqueous solution than the Mg/Al-LDH. The SEM image of G-LDH shows a distinct micro-spherical morphology, and it can maintain the micro-spherical morphology even after adsorbing Congo Red and hexavalent chromium. G-LDH showed strong adsorption properties for CR (Congo red) and Cr (VI) solutions with initial concentrations of 80 mg L-1 and 100 mg L-1, with adsorption amounts of 361.6 mg g-1 and 461.7 mg g-1. The unique layered structure of Mg/Al-LDH made an indispensable contribution to the efficient adsorption capacity of G-LDH when GG was used to prepare composite microspheres. The adsorption process of G-LDH is consistent with the Langmuir isotherm model and the proposed secondary kinetic model as a heat-absorbing, spontaneous, monolayer, and chemisorption process. G-LDH is an innovative anion adsorbent with excellent adsorption performance at low cost, using natural polymer materials as the backbone and the layered structure of magnesium‑aluminum hydrotalcite as the support.

Quaternized and Hyperbranched Amidoxime-Modified Ultra-High-Molecular-Weight Polyethylene Fiber for Uranium Extraction from Seawater

The most promising material for uranium extraction from saltwater is generally acknowledged to be fibrous adsorbents. An irradiation-modified anti-biofouling ultra-high-molecular-weight polyethylene (UHMWPE-g-PGAO) fibrous adsorbent with a hyperbranched structure was synthesized. It exhibited adsorption capacities of 314.8 mg-U/g-Ads in aqueous solution and 4.04 mg-U/g-Ads in simulated seawater over a 28-day period. The ultra-high-molecular-weight polyethylene (UHMWPE) fiber was functionalized by covalently linking hyperbranched polyethyleneimine (h-PEI) to facilitate the migration of uranyl ions within the fibers. Additionally, amidoxime and quaternary ammonium groups were immobilized on the fiber surface to enhance uranium affinity and provide defense against marine organisms. This three-dimensional design of amidoxime and h-PEI-modified UHMWPE fiber retained more than 91.0% of its maximum adsorption capacity after undergoing five adsorption-desorption cycles. The UHMWPE-g-PGAO adsorbent exhibits significant antibacterial activity against Escherichia coli and Staphylococcus aureus, achieving an inactivation efficiency of over 99.9%. It is proved to be an innovative fiber adsorbent for uranium extraction from seawater for its biofouling resistance, robustness, and reusability.

Modular hydrogel selectively adsorbs phosphates and hexavalent chromium while enabling phosphate recovery

Electroplating wastewater containing high concentrations of phosphates and hexavalent chromium Cr(VI) poses serious environmental pollution. Moreover, phosphorus, as a non-renewable resource, necessitates its recovery to meet sustainable development goals. To address this issue, this study used sodium alginate as the scaffold module, synthesized lanthanum carbonate in situ within a chitosan module to serve as the phosphate adsorption module, and employed polyethyleneimine (PEI) modules to enhance the adsorption capacity for Cr(VI), successfully fabricating a modular hydrogel (LC-CSP). LC-CSP exhibits a complex porous structure and surface morphology, forming an ultra-low-density fiber network with good strength and elasticity, ensuring uniform distribution and exposure of active sites. Under optimal conditions for single-component adsorption, LC-CSP achieved adsorption capacities of 232.02 mg/g for phosphates and 474.61 mg/g for Cr(VI). Additionally, LC-CSP demonstrated excellent reusability, retaining over 83 % of its performance after five cycles. In simulated electroplating wastewater experiments with various interfering substances, LC-CSP maintained high removal efficiencies (>90.72 %) for phosphates and Cr(VI). Post-experiment, enriched water after phosphate desorption was further treated to recover phosphorus resources in complex water environments. Multiple characterization techniques elucidated the adsorption mechanisms of LC-CSP: phosphate adsorption primarily involved ligand exchange, electrostatic interactions, and hydrogen bonding, while Cr(VI) adsorption included electrostatic interactions, hydrogen bonding, and reduction reactions. Finally, fixed-bed simulated wastewater adsorption experiments validated the technical potential of LC-CSP for practical electroplating wastewater management.

Advanced treatment and reuse of dye wastewater using thermo-irreversible on/off switch starch with disruption of dissolution/precipitation dynamic equilibrium

The development of irreversible on/off switching materials is a potential strategy for unidirectional capture and encapsulation of pollutants, preventing the pollutant leakage problem resulting from the reversible dissolution of flocculants. Herein, a thermo-irreversible on/off switch starch (TISS) is prepared through modifying starch by etherification grafting glycidyl phenyl ether and 2,4-bis(dimethylamino)-6-chloro-[1,3,5]-triazine. It breaks the dissolution/precipitation dynamic equilibrium across heating-cooling cycles by thermal-induced irreversible coil-to-globule self-assembly of polymer chains, resulting in a 50-fold decrease in polymer solubility. Particularly, TISS shows a superior double-locking effect on pollutants and flocculants through its unique irreversible conformation memory capability, leading to a high-quality reuse water. 99.9 % of reactive brilliant red dye and 97.9 % of TISS remain fixed within sludge flocs even after prolonged immersion in cold water at 24 °C for 60 days. Furthermore, direct recycling and reuse of dye-bath energy can be realized through the isothermal flocculation and dyeing method, showing a 75 % decrease in energy consumption after three cycles compared to traditional dyeing techniques. This work presents a novel approach to constructing an irreversible pollutant delivery system using thermo-irreversible on/off switch starch, addressing the problems of high energy dissipation and water quality fluctuations during wastewater treatment.

Synthesis of recyclable and light-weight graphene oxide/chitosan/genipin sponges for the adsorption of diclofenac, triclosan, and microplastics

Emerging micropollutants, such as pharmaceuticals and microplastics (MPs), have become a pressing water environmental concern. The aim of this study is to synthesize chitosan sponges using graphene oxide (GO) and genipin (GP) for the removal of pharmaceuticals (diclofenac (DCF) and triclosan (TCS)) and MPs, verify their adsorption mechanisms, evaluate the effects of temperature, pH, and salinity on their adsorption capacities, and determine their reusability. The GO5/CS/GP sponge exhibited a macroporous nature (porosity = 95%, density = 32.6 mg/cm3). GO and cross-linker GP enhanced the adsorption of DCF, TCS, and polystyrene (PS) MPs onto the CS sponges. The adsorption of DCF, TCS, and PS MPs involved multiple steps: surface diffusion and pore diffusion of the sponge. The adsorption isotherms demonstrated that Langmuir model was the most fitted well model to explain adsorption of TCS (qm = 7.08 mg/g) and PS MPs (qm = 7.42 mg/g) on GO5/CS/GP sponge, while Freundlich model suited for DCF adsorption (qm = 48.58 mg/g). DCF adsorption was thermodynamically spontaneous and endothermic; however, the adsorption of TCS and PS MPs was exothermic (283-313 K). The optimal pH was 5.5-7 due to the surface charge of the GO5/CS/GP sponge (pHzpc = 5.76) and ionization of DCF, TCS, and PS MPs. As the salinity increased, DCF removal efficiency drastically decreased due to the weakening of electrostatic interactions; however, TCS removal efficiency remained stable because TCS adsorption was mainly caused by hydrophobic and π-π interactions rather than electrostatic interaction. The removal of PS MPs was enhanced by the electrostatic screening effects of high Na+ ions. PS nanoplastics (average size = 26 nm) were removed by the GO5/CS/GP sponge at a rate of 73.0%, which was better than that of PS MPs (41.5%). In addition, the GO5/CS/GP sponge could be recycled over five adsorption-desorption cycles.

Anodic Electrodepositing Bioinspired Cu-BDC-NH2@Graphene Oxide Membrane for Efficient Uranium Extraction

The challenge of removing trace levels of heavy metal ions, particularly uranium, from wastewater is a critical concern in environmental management. Uranium, a key element in long-term nuclear power generation, often poses significant extraction difficulties in wastewater due to its low concentration, interference from other ions, and the complexity of aquatic ecosystems. This study introduces an anodic electrodeposited hierarchical porous 2D metal-organic framework (MOF) Cu-BDC-NH2@graphene oxide (GO) membrane for effective uranium extraction by mimicking the function of the superb-uranyl-binding protein. This membrane is characterized by its hierarchical pillared-layer structures resulting from the controlled orientation of Cu-BDC-NH2 MOFs within the laminated GO layers during the electrodeposition process. The integration of amino groups from 2D Cu-BDC-NH2 and carboxylate groups from GO enables a high affinity to uranyl ions, achieving an unprecedented uranium adsorption capacity of 1078.4 mg/g and outstanding selectivity. Our findings not only demonstrate a breakthrough in uranium extraction technology but also pave the way for advancements in water purification and sustainable energy development, proposing a practical and efficient strategy for creating orientation-tunable 2D MOFs@GO membranes tailored for high-efficiency uranium extraction.

Robust functionalized cellulose-based porous composite for efficient capture and ultra-fast desorption of aqueous heavy metal pollution

The heavy metal pollution control industry requires convenient and cost-effective solutions to address complex aqueous environment. Adsorption method can be an effective strategy to realize these goals. Considering the importance of environmental and sustainable development strategies, there is an urgent need to develop efficient, green and non-toxic heavy metal adsorbents. In this work, a robust aminated cellulose-based porous adsorbent (PGPW) was developed from delignified wood and amino-rich polymer using a solvent-free, mild, simple and efficient preparation method. Such adsorbent exhibited excellent adsorption capacity (188.68 mg g-1) for Cu(II), and its adsorption behavior was consistent with pseudo-second order kinetic and Langmuir isotherm models. Notably, PGPW with superior compressibility could be squeezed to achieve rapid desorption and reach equilibrium within 5 min, while still retaining 87 % adsorption efficiency after 50 cycles. In addition, PGPW showed remarkable selectivity towards various coexisting ionic systems and demonstrated a considerable adsorption capacity in natural water applications. The adsorption mechanism of heavy metal ions on porous adsorption material was elucidated. This approach provides a simple, gentle and sustainable strategy for preparing functionalized wood-based composites with efficient adsorption and ultra-fast desorption of heavy metal ions.

Recent developments and challenges in uranium extraction from seawater through amidoxime-functionalized adsorbents

As per statistical estimations, we have only around 100 years of uranium life in terrestrial ores. In contrast, seawater has viable uranium resources that can secure the future of energy. However, to achieve this, environmental challenges need to be overcome, such as low uranium concentration (3.3 ppb), fouling of adsorbents, uranium speciation, oceanic temperature, and competition between elements for the active site of adsorbent (such as vanadium which has a significant influence on uranium adsorption). Furthermore, the deployability of adsorbent under seawater conditions is a gigantic challenge; hence, leaching-resistant stable adsorbents with good reusability and high elution rates are extremely needed. Powdered (nanostructured) adsorbents available today have limitations in fulfilling these requirements. An increase in the grafting density of functional ligands keeping in view economic sustainability is also a major obstacle but a necessity for high uranium uptake. To cope with these challenges, researchers reported hundreds of adsorbents of different kinds, but amidoxime-based polymeric adsorbents have shown some remarkable advantages and are considered the benchmark in uranium extraction history; they have a high affinity for uranium because of electron donors in their structure, and their amphoteric nature is responsible for effective uranium chelation under a wide range of pH. In this review, we have mainly focused on recent developments in uranium extraction from seawater through amidoxime-based adsorbents, their comparative analysis, and problematic factors that are needed to be considered for future research.

Flexible fabrication chitosan-polyamidoamine aerogels by one-step method for efficient adsorption and separation of anionic dyes

Chitosan in situ grown polyamidoamine (CTS-Gx PAMAM (x = 0, 1, 2, 3)) aerogels were fabricated by a facile one-step freeze-drying method, with glutaraldehyde serving as a crosslinker. The three-dimensional skeletal structure of aerogel provided numerous adsorption sites and accelerated the effective mass transfer of pollutants. The adsorption kinetics and isotherm studies of the two anionic dyes were consistent with the pseudo-second-order and Langmuir models, indicating that the removal of rose bengal (RB) and sunset yellow (SY) was a monolayer chemisorption process. The maximum adsorption capacity of RB and SY reached 370.28 mg/g and 343.31 mg/g, respectively. After five adsorption-desorption cycles, the adsorption capacities of the two anionic dyes reached 81.10% and 84.06% of the initial adsorption capacities, respectively. The major mechanism between the aerogels and dyes was systematically investigated based on using Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and energy-dispersive spectroscopy analyses, confirming that electrostatic interaction, hydrogen bonding and van der Waals interactions were the main driving forces for the superior adsorption performance. Furthermore, the CTS-G2 PAMAM aerogel exhibited good filtration and separation performance. Overall, the novel aerogel adsorbent possesses excellent theoretical guidance and practical application potential for the purification of anionic dyes.

Biomimetic Polylactic Acid Electrospun Fibers Grafted with Polyethyleneimine for Highly Efficient Methyl Orange and Cr(VI) Removal

The rapid growth of industrialization has resulted in the release of large quantities of pollutants into the environment, especially dyes and heavy metals, which are environmentally hazardous for humans and animals. It is considered as the most promising and environmentally friendly route to develop green materials by using the green modification method, which has no negative impact on the environment. In this work, the green material of polylactic acid (PLA) was used as the substrate material, and a novel modification method of polydopamine (PDA)-assisted polyethyleneimine (PEI) grafting was developed. The electrospun PLA fibers are mainly composed of stereocomplex crystallites, which were achieved via the electrospinning of poly(l-lactic acid) and poly(d-lactic acid). The water-soluble PEI was grafted onto the PDA-modified PLA fibers through the glutaraldehyde-assisted cross-linking reaction. The prepared composite fibers can be degraded, which is environmentally friendly and meets the requirements of sustainable development. The potential application of such PLA composite fibers in wastewater treatment was intensively evaluated. The results show that at appropriate fabrication conditions (PDA concentration of 3 g·L^-1 and a PEI molecular weight of 70,000 g·mol^-1), the composite fibers exhibit the maximum adsorption capacities of 612 and 398.41 mg·g^-1 for methyl orange (MO) and hexavalent chromium [Cr(VI)], respectively. Simultaneously, about 64.79% of Cr(VI) adsorbed on the composite fibers was reduced to Cr(III). The above results show that the PLA composite fibers have a good development prospect in the field of wastewater treatment.

Spirulina platensis Immobilized Alginate Beads for Removal of Pb(II) from Aqueous Solutions

Microalgae contain a diversity of functional groups that can be used as environmental adsorbents. Spirulina platensis is a blue-green microalga that comprises protein-N, which is advantageous for use in nitrogen-containing biomass as adsorbents. This study aimed to enhance the adsorption properties of alginate hydrogels by employing Spirulina platensis. Spirulina platensis was immobilized on sodium alginate (S.P@Ca-SA) via crosslinking. The results of field-emission scanning electron microscopy, Fourier-transform infrared, and X-ray photoelectron spectroscopy analyses of the N-containing functional groups indicated that Spirulina platensis was successfully immobilized on the alginate matrix. We evaluated the effects of pH, concentration, and contact time on Pb(II) adsorption by S.P@Ca-SA. The results demonstrated that S.P@Ca-SA could effectively eliminate Pb(II) at pH 5, reaching equilibrium within 6 h, and the maximum Pb(II) sorption capacity of S.P@Ca-SA was 87.9 mg/g. Our results indicated that S.P@Ca-SA fits well with the pseudo-second-order and Freundlich models. Compared with Spirulina platensis and blank alginate beads, S.P@Ca-SA exhibited an enhanced Pb(II) adsorption efficiency. The correlation implies that the amino groups act as adsorption sites facilitating the elimination of Pb(II).

Chitosan-based composite microspheres for treatment of hexavalent chromium and EBBR from aqueous solution

Hexavalent chromium is widely used in industrial fields, but its pollution has posed a great threat to the environment due to its high toxicity. We created a chitosan-based microsphere biosorbent (CP) by combining polyethyleneimine with chitosan adopting inverse emulsion polymerization method. Under the optimal conditions (pH = 3), the maximum adsorption capacity of composite microspheres can reach 299.89 mg g^-1, which is much higher than that of chitosan microspheres (168.91 mg g^-1). When the amount of CP is 0.25 g L^-1, the removal rate of 50 mg L^-1 Cr(VI) and 50 mg L^-1 Eriochrome blue-black R (EBBR) can reach 95% and 99%, respectively. The time required for CP to reach adsorption equilibrium (180 min) was significantly shorter than that of chitosan microspheres (540 min), and the adsorption rate was significantly improved. Langmuir isotherm model, pseudo-second-order kinetic model and thermodynamic calculation results penetrated an endothermic spontaneous, monolayer, and chemical adsorption process. Biomass composite microspheres CP has obvious selectivity and the adsorption capacity retention rate of CP was still 71.32% after four adsorption cycles. This work proposed an easily prepared and biomass-based microspheres for the effective removal of Cr(VI) in printing and dyeing wastewater pollution through adsorption.

Preparation of a laminated structured polyethyleneimine cryogel for carbon capture

A cryogel solid amine adsorbent with a laminated structure has been prepared by crosslinking polyethylenimine (PEI) with ethylene glycol diglycidyl ether (EGDE) at a low temperature via liquid nitrogen treatment and freeze-drying. The effects of cryogenic treatment on the morphology of the cryogels were investigated. The liquid nitrogen treatment and freeze drying were critical to create the layered structure. The fast formation of ice crystals at 77 K served as a template which directed the ordered lamellar structure of the PEI and EGDE cross-linked polymer networks. The PEI cryogel adsorbent showed excellent CO₂ adsorption performance both in dry and wet conditions. In dry conditions, the PEI-gel-5-0.25 cryogel showed a 5.60 mmol/g of CO₂ adsorption capacity at 75 °C. After being swelled with water, the PEI-gel-15-0.25 cryogel showed an extremely high CO₂ adsorption capacity of 11.39 mmol/g at 25 °C. The adsorption behaviors of adsorbents with varied water contents were explained using kinetic simulations and intraparticle diffusion simulations. It was found that the presence of water can significantly enhance the diffusion process. The regeneration performance was examined in both dry and wet conditions. After 20 adsorption-desorption cycles, the adsorption capacity of the regenerated PEI cryogel had barely decreased, indicating reliable regeneration stability.

Selective extraction of synthetic cathinones new psychoactive substances from wastewater, urine and cocktail using dummy molecularly imprinted polymers

Dummy molecularly imprinted polymers (DMIPs) for selective extraction of five common synthetic cathinones (SCs) were prepared by bulk polymerization. DMIPs materials possessed narrow diameter distribution (30-60 µm) and large specific surface area (329.6 m² g^-1). Imprinting factors for cathinone, methcathinone, mephedrone, methylone and ethylone were 1.11-1.82. DMIPs could also quickly adsorb SCs from aqueous solutions within 5 min. Therefore, the materials were used as solid-phase extraction (SPE) sorbents to selectively extract five SCs in complex samples. An accurate and sensitive analytical method based on DMIPs-SPE combined with HPLC-MS/MS was established. Under optimal conditions, the established method showed low limits of detection (0.002-0.1 ng mL^-1), satisfactory recoveries (84.1-97.7%) and good repeatability (relative standard deviation (RSD) below 9%). The method was successfully verified using wastewater, urine and cocktail samples. Recoveries of SCs at three spiking levels were in the range of 75.1-98.6%, with RSD values below 7.0%. Compared with commercial sorbents, DMIPs showed better clean-up ability with matrix effect values of -24.1%-8.3% for all SCs in wastewater, urine and cocktail samples. Therefore, the developed DMIPs-SPE-HPLC-MS/MS strategy could be used as a specific and cost-effective method for sensitive determination of SCs in complex samples.

Selective adsorption of anionic dye from wastewater using polyethyleneimine based macroporous sponge: Batch and continuous studies

Dyes are well known for their hazardous impacts on public health and the environment. Dye removal using monolithic adsorbents is an attractive approach for industrial applications and process design owing to their utilization in both static and dynamic adsorption experiments. In the present work, polyethyleneimine (PEI) based macroporous monolithic sponge (S₁₀₀) was engineered by ice-templating method and used as an adsorbent. Both batch and continuous operations for dye removal were studied. The effect of various parameters such as pH, adsorbent amount, flow rate, influent dye concentration, and adsorbent bed height on adsorption performance of S₁₀₀ was studied and modelled using Langmuir/Freundlich isotherms for static operations and Adam-Bohart/Thomas model in packed-bed column experiments. Under optimum conditions, the adsorbent showed a remarkably higher adsorption capacity towards CR (1666.67 mg/g), which is considerably higher than most PEI-based adsorbents. Amine groups in S₁₀₀ offered exceptional selectivity for anionic Congo red (CR) against cationic Methylene blue (MB) dye (separation factor of 208 and 87 in absence and presence of sodium chloride, respectively). It can be easily regenerated in alkaline medium without a significant loss in percent adsorption capacity and shows good thermal and mechanical stability. Notably, in column studies, a relatively smaller percentage of unused bed height (32.3%) was observed with higher dye uptake for 16 mg S₁₀₀ at flow rate 10 mL/h and inlet concentration 300 mg/L. Thus, the adsorbent displays an outstanding physiochemical characteristic, excellent selectivity for anionic dye, ease of regeneration and high adsorption performance in both batch and continuous studies.

A Membrane-Supported Bifunctional Poly(amidoxime-ethyleneimine) Network for Enhanced Uranium Extraction from Seawater and Wastewater

Uranium extraction from natural seawater and wastewater are quintessential requirements to supply uninterrupted carbon-free nuclear energy and to prevent potential radiochemical and toxicological effects, respectively. Owing to the complexity and low-concentration uranium of these water samples, the design and synthesis of sorbent materials for uranium extraction with meaningful efficiencies remains a grand challenge. Herein, we reported a novel three-dimensional bifunctional network of hyperbranched poly(amidoxime-ethyleneimine) (PAO-h-PEI) using PEI as the skeleton material via cyanoethylation, crosslinking and then amidoximation. As a result of the synergistic supramolecular strategy, the PAO-h-PEI membrane achieved a remarkable adsorption capacity of 985.7 mg/g for aqueous uranium solution, which was 2.5 folds that of the monofunctional h-PEI membrane (387.6 mg/g). The PAO-h-PEI membrane also exhibited good selectivity towards uranium in the presence of various metal ions, high-content salt, and natural organic matter as well as common anions. According to the XPS and FTIR results, the utilization of amines as the second ligand enhanced uranyl binding by providing additional coordination sites or by interacting with oxime to force N-OH dissociation. The good reusability (adsorption rate of 93% after six adsorption-desorption cycles) and satisfactory adsorption performance in extracting low-concentration uranium in real seawater demonstrate its practicability.

Adsorption properties and recognition mechanisms of a novel surface imprinted polymer for selective removal of Cu(II)-citrate complexes

Cu(II)-citrate (Cu(II)-CA) complex, as one of the components in plating solutions, increases the difficulty of Cu(II) treatment due to its stable structure and high mobility. In this work, a novel surface imprinted polymer (Cu-CA-SIP) for selective removal of Cu(II)-CA complex from aqueous solution is synthesized by using polyethyleneimine (PEI) grafted onto chloromethylated polystyrene (CMP) microspheres. Cu(II)-CA anions are successfully imprinted with the molar ration of 1:1 by Cu-CA-SIP at initial pH 4.0. Nearly 100% removal rate can be achieved even at low Cu(II)-CA concentration (0.5 mmol/L), and the maximum Cu(II) uptake of Cu-CA-SIP reaches 1.38 mmol/g at 303 K. In Cu(II)/Fe(III)-CA, Cu(II)/Ni(II)-CA, Cu(II)/Zn(II)-CA and Cu(II)/Cd(II)-CA systems, the relative selectivity coefficients of Cu-CA-SIP for Cu(II)-CA are 9.66, 2.32, 1.40 and 44.55, respectively. Moreover, Cu-CA-SIP can be retrieved with negligible loss of adsorption capacity after six times of reuse. The Cu-CA-SIP column can effectively treat the actual electroplating wastewater within 114 BV, and can still reach 104 BV after three dynamic cycles. Therefore, an innovative imprinted material is designed for the first time on the basis of coordination-configuration recognition mechanism for the treatment of electroplating wastewater, providing a new insight in developing surface imprinted polymer in environmental remediation.

Thiolated Polyethyleneimine-Based Polymer Sponge for Selective Removal of Hg2+ from Aqueous Solution

Polymer sponges with molecular recognition provide a facile approach to water purification and industrial separation with easy operation. Herein, a thiolated polyethyleneimine (PEI)-based polymer sponge was prepared through cryo-polymerization of PEI, followed by grafting of PEI and then post-modification of the amine functionalities present within the hyperbranched structure with methyl mercaptoacetate, which afford high density of thiol functional groups on the surface of the sponge. The developed sponge was characterized by scanning electron microscopy and element analysis, and the adsorption kinetic and isotherm studies were conducted in detail. The sponge presents a remarkable maximum adsorption capacity of 2899.7 mg/g, which can be attributed to its high density of thiol functionalities. The sponge also shows excellent selectivity toward Hg²⁺ against other metal ions and natural organic matter, indicating its great potential in removing mercury from real water bodies. In addition, the sponge can be chemically regenerated and exhibits good reusability, which decreases the economic and environmental impacts. Hence, the high removal efficiency, high selectivity toward mercury, and good reusability of the sponge material highlight it as a promising sorbent for mercury removal in water pollution treatment.